SoCFPGA DTS updates for v6.14
- Remove unused and undocumented property "snps,max-mtu"
- Add gpio and spi node for Agilex5
- Add VGIC maintenance interrupt for Agilex
- Use correct reset name of "stmmaceth-ocp" instead of "ahb"
- Drop unused #address-cells/#size-cells in the cyclone5-mcvevk
* tag 'socfpga_dts_updates_v6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: altera: Remove unused and undocumented "snps,max-mtu" property
arm64: dts: socfpga: agilex5: Add gpio0 node and spi dma handshake id
arm64: dts: socfpga: agilex: Add VGIC maintenance interrupt
arm: dts: socfpga: use reset-name "stmmaceth-ocp" instead of "ahb"
ARM: dts: socfpga_cyclone5_mcvevk: Drop unused #address-cells/#size-cells
Link: https://lore.kernel.org/r/20250103023012.1268627-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor improvements in ARM DTS for v6.14
1. Marvell: Use un-deprecated hp-det-gpios (no ABI impact expected).
2. SoCFPGA: Drop spidev devices which are not properly described in DTS,
but are using some other compatibles. This was part of wider tree
effort to fix such incorrect hardware descriptions.
Important: Dropping this device node will have user-visible impact:
spidev device will not register.
* tag 'dt-cleanup-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: socfpga: remove non-existent DAC from CycloneV devkit
ARM: dts: marvell: mmp2-olpc-xo-1-75: Switch to {hp,mic}-det-gpios
Link: https://lore.kernel.org/r/20241231132847.135814-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor improvements in ARM64 DTS for v6.14
1. Spreadtrum:
- Correct few issues pointed out by DT schema around properties and
node names.
- Move fuel-gauge from DTSI to DTS, because it belongs to the board.
- Use undeprecated properties, like battery-detect-gpios, already
supported by Linux.
2. Uniphier: Use un-deprecated hp-det-gpios (no ABI impact expected).
* tag 'dt64-cleanup-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
arm64: dts: sprd: Fix battery-detect-gpios property
arm64: dts: uniphier: Switch to hp-det-gpios
arm64: dts: sprd: sc9863a: reorder clocks, clock-names per bindings
arm64: dts: sprd: sc9863a: fix in-ports property
arm64: dts: sprd: sc2731: move fuel-gauge monitored-battery to device DTS
arm64: dts: sprd: sp9860g-1h10: fix factory-internal-resistance-micro-ohms property
arm64: dts: sprd: sp9860g-1h10: fix constant-charge-voltage-max-microvolt property
Link: https://lore.kernel.org/r/20241231132847.135814-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM64 changes for v6.14
1. Exynos8895: Add UART nodes, PMU (performance) for the M2 cluster and
I2C controllers in the camera block (HSI2C in CAM0-3).
2. Exynos990: Add Power Management Unit (Samsung block), PMU
(performance) for M5 cluster and two clock controllers.
3. ExynosAutov920: Add watchdog and DMA controllers.
4. Google GS101: Minor fixes for phy and USB. Add USB Type-C.
5. Exynos850-e850-96 board: Drop gap in memory layout.
6. New SoC: Exynos9810.
7. New boards, all mobile phones:
- Exynos9810:
Samsung Galaxy S9 (SM-G960F)
- Exynos990:
Samsung Galaxy S20 FE (SM-G780F)
Samsung Galaxy S20 5G (SM-G980F)
* tag 'samsung-dt64-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (23 commits)
arm64: dts: exynos8895: Add camera hsi2c nodes
arm64: dts: exynos990: Add clock management unit nodes
arm64: dts: exynos: gs101-oriole: add pd-disable and typec-power-opmode
arm64: dts: exynos: gs101-oriole: enable Maxim max77759 TCPCi
arm64: dts: exynos: Add initial support for Samsung Galaxy S9 (SM-G960F)
arm64: dts: exynos: Add Exynos9810 SoC support
arm64: dts: exynos850-e850-96: Specify reserved secure memory explicitly
arm64: dts: exynos990: Add a PMU node for the third cluster
arm64: dts: exynosautov920: Add DMA nodes
arm64: dts: exynos8895: Add a PMU node for the second cluster
dt-bindings: clock: samsung: Add Exynos990 SoC CMU bindings
arm64: dts: exynosautov920: add watchdog DT node
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 (x1slte)
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 5G (x1s)
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 Series boards (x1s-common)
dt-bindings: arm: samsung: samsung-boards: Add bindings for SM-G981B and SM-G980F board
arm64: dts: exynos: gs101: allow stable USB phy Vbus detection
arm64: dts: exynos: gs101: phy region for exynos5-usbdrd is larger
MAINTAINERS: add myself and Tudor as reviewers for Google Tensor SoC
arm64: dts: exynos990: Add pmu and syscon-reboot nodes
...
Link: https://lore.kernel.org/r/20241231131742.134329-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
thead-dt-for-v6.14: T-HEAD Devicetrees for v6.14
Add mailbox node for the T-Head TH1520 RISC-V SoC. The mailbox bindings
and driver were already merged in v6.13:
b2cf36e4a2 ("dt-bindings: mailbox: Add thead,th1520-mailbox bindings")
5d4d263e1c ("mailbox: Introduce support for T-head TH1520 Mailbox driver")
Signed-off-by: Drew Fustini <drew@pdp7.com>
* tag 'thead-dt-for-v6.14' of https://github.com/pdp7/linux:
riscv: dts: thead: Add mailbox node
mdio-gpio is not a valid pattern according to mdio-gpio.yaml.
Use the generic 'mdio' name to fix the following dt-schema warnings:
'mdio-gpio' does not match '^mdio(-(bus|external))?(@.+|-([0-9]+))?$'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently there are 3 type of boards (imx6q|imx6qp|imx6dl-sabresd)
based on imx6qdl-sabresd.dtsi, they all do not set the dr_mode for
usbotg device node. The chipidea usb driver will configure it to otg
mode by default if the dr_mode is not set, but some testcases need to
parse the dr_mode from DT and decide the follow-up test strategy, here
set the dr_mode to otg explicitly for these 3 imx6qdl-sabresd based
boards.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to adv7180.yaml, the correct property name is
"adi,force-bt656-4".
Update it accordingly to fix several dt-schema warnings:
adv7280@21: 'adv,force-bt656-4' does not match any of the regexes: ...
imx6qdl-apalis.dtsi is the only in-tree kernel user of this property.
BSD does have a adv7180 driver, so should not be impacted.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The regulator handling was introduced by commit `966d73152078 (usb: phy:
mxs: enable regulator phy-3p0 to improve signal qualilty, 2024-07-26)`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d731520 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d731520 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In the schematics, the MCLK2 pin is shown as connected to CODEC_CLK32K,
which is derived from the same 32KHZ_PMIC clock as Bluetooth/WiFi and
GPS clocks. 32KHZ_PMIC is connected to the BTCLK pin, represented in
mainline as S2MPS11_CLK_BT.
Add the MCLK2 clock to the WM1811 codec clock property to properly
describe the hardware.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20240816-midas-audio-tab3-v2-4-48ee7f2293b3@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
When the serial console is enabled, we need to disable power delivery
since serial uses the SBU1/2 pins and appears to confuse the TCPCI,
resulting in endless interrupts.
For now, change the DT such that the serial console continues working.
Note1: We can not have both typec-power-opmode and
new-source-frs-typec-current active at the same time, as otherwise DT
binding checks complain.
Note2: When using a downstream DT, the Pixel boot-loader will modify
the DT accordingly before boot, but for this upstream DT it doesn't
know where to find the TCPCI node. The intention is for this commit to
be reverted once an updated Pixel boot-loader becomes available.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241203-gs101-phy-lanes-orientation-dts-v2-5-1412783a6b01@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
On Pixel 6 (and Pro), a max77759 companion PMIC for USB Type-C
applications is used, which contains four functional blocks (at
distinct I2C addresses):
* top (including GPIO)
* charger
* fuel gauge
* TCPCi
While in the same package, TCPCi and Fuel Gauge have separate I2C
addresses, interrupt lines and interrupt status registers and can be
treated independently.
The TCPCi is required to detect and handle connector orientation in
Pixel's USB PHY driver, and to configure the USB controller's role
(host vs device).
This change adds the TCPCi part as it can be independent and doesn't
need a top-level MFD.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241203-gs101-phy-lanes-orientation-dts-v2-4-1412783a6b01@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Exynos 9810 is an ARMv8 mobile SoC found in various Samsung devices,
such as Samsung Galaxy S9 (starlte), S9 Plus (star2lte),
Note 9 (crownlte) and perhaps others.
Add minimal support for this SoC, including basic stuff like:
- PSCI for bringing up secondary cores
- ARMv8 generic timer
- GPIO and pinctrl.
The firmware coming with the devices based on this SoC is buggy
and doesn't configure CNTFRQ_EL0, as required by spec, so it's
needed to hardcode the frequency in the timer node.
Co-developed-by: Maksym Holovach <nergzd@nergzd723.xyz>
Signed-off-by: Maksym Holovach <nergzd@nergzd723.xyz>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20241214-exynos9810-v4-1-4e91fbbc2133@gmail.com
[krzysztof: Rename and move PMU nodes to proper sorting position]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Instead of carving out the secure area in 'memory' node, let's describe
it in 'reserved-memory'. That makes it easier to understand both RAM
regions and particular secure world memory region. Originally the device
tree was created in a way to make sure it was well aligned with the way
LittleKernel bootloader modified it. But later it was found the
LittleKernel works fine with properly described reserved regions, so
it's possible now to define those in a cleaner way.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20241211033027.12985-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Renesas DTS updates for v6.14
- Add more serial (SCIF), power monitor, ADC, and sound support for
the RZ/G3S SoC and the RZ/G3S SMARC SoM and development board,
- Add support for the R-Car V4H ES3.0 (R8A779G3) SoC on the White Hawk
Single development board,
- Add display support for the R-Car V4M SoC and the Gray Hawk Single
development board,
- Add video capture support for the Gray Hawk Single development
board,
- Add initial support for the RZ/G3E (R9A09G047) SoC and the RZ/G3E
SMARC SoM and Carrier-II EVK development board,
- Add support for 5-port MATEnet on the Falcon Ethernet sub-board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.14-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (33 commits)
arm64: dts: renesas: r9a09g047: Add I2C nodes
arm64: dts: renesas: rzg3s-smarc: Add sound card
arm64: dts: renesas: rzg3s-smarc: Enable SSI3
arm64: dts: renesas: Add da7212 audio codec node
arm64: dts: renesas: rzg3s-smarc-som: Add versa3 clock generator node
arm64: dts: renesas: r9a08g045: Add SSI nodes
arm64: dts: renesas: rzg3s-smarc-som: Enable ADC
arm64: dts: renesas: r9a08g045: Add ADC node
arm64: dts: renesas: Add initial device tree for RZ/G3E SMARC EVK board
arm64: dts: renesas: Add initial support for RZ/G3E SMARC SoM
arm64: dts: renesas: r9a09g047: Add OPP table
arm64: dts: renesas: Add initial DTSI for RZ/G3E SoC
arm64: dts: renesas: falcon-ethernet: Describe PHYs connected on the breakout board
arm64: dts: renesas: r8a779a0: Remove address- and size-cells from AVB[1-5]
dt-bindings: clock: renesas: Document RZ/G3E SoC CPG
dt-bindings: soc: renesas: Document RZ/G3E SMARC SoM and Carrier-II EVK
dt-bindings: soc: renesas: Document Renesas RZ/G3E SoC variants
arm64: dts: renesas: gray-hawk-single: Add video capture support
arm64: dts: renesas: gray-hawk-single: Add DisplayPort support
arm64: dts: renesas: r8a779h0: Add display support
...
Link: https://lore.kernel.org/r/cover.1734689803.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT for v6.14, round 1
Highlights:
----------
- MPU:
- STM32MP13:
- Populate all timer counter nodes in Soc file.
- Enable counter (timers) on stm32mp135f-dk.
- DH core: increase CPU voltage to fit with STM32MP135F datasheet.
- STMP32MP15:
- Populate all timer counter nodes in Soc file.
- Enable counter (timers) on stm32mp15 EV1 and DK boards.
- OCTAVO:
- LXA-TAC (gen1/2): disable RTC, update aliases and
adjust USB gadget.
- Add LXA-TAC gen3 based on OSD32MP153x SIP:
STMP32MP153, RAM, PMIC.
- DH: minor fixes.
- STM32MP25:
- Enable imx335/CSI/DCMIPP pipeline on stm32mp257f-ev1.
- Add I2S, SAI, SPDIFRX supports.
- Add and enable COMBOPHY on stm32mp257f-ev1. Combophy is used
by PCIe and USB3.
* tag 'stm32-dt-for-v6.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (23 commits)
arm64: dts: st: enable imx335/csi/dcmipp pipeline on stm32mp257f-ev1
arm64: dts: st: add csi & dcmipp node in stm32mp25
ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM
ARM: dts: stm32: add counter subnodes on stm32mp157 dk boards
ARM: dts: stm32: add counter subnodes on stm32mp157c-ev1
ARM: dts: stm32: add counter subnodes on stm32mp135f-dk
ARM: dts: stm32: populate all timer counter nodes on stm32mp15
ARM: dts: stm32: populate all timer counter nodes on stm32mp13
ARM: dts: stm32: lxa-tac: Add support for generation 3 devices
ARM: dts: stm32: lxa-tac: move adc and gpio{e,g} to gen{1,2} boards
dt-bindings: arm: stm32: add compatible strings for Linux Automation LXA TAC gen 3
ARM: dts: stm32: lxa-tac: adjust USB gadget fifo sizes for multi function
ARM: dts: stm32: lxa-tac: extend the alias table
ARM: dts: stm32: lxa-tac: disable the real time clock
ARM: dts: stm32: Fix IPCC EXTI declaration on stm32mp151
ARM: dts: stm32: Sort M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT
ARM: dts: stm32: Increase CPU core voltage on STM32MP13xx DHCOR SoM
ARM: dts: stm32: Deduplicate serial aliases and chosen node for STM32MP15xx DHCOM SoM
arm64: dts: st: Enable COMBOPHY on the stm32mp257f-ev1 board
arm64: dts: st: Add combophy node on stm32mp251
...
Link: https://lore.kernel.org/r/7ffcca65-3953-413a-bcf3-0702a6b0518b@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the camera pipeline with a imx335 sensor connected to the
dcmipp via the csi interface.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add nodes describing the csi and dcmipp controllers handling the
camera pipeline on the stm32mp25x.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Remove "enable-dma" and "bus-id" properties which are both unused in the
kernel and undocumented. Most likely they are leftovers from downstream.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Remove "snps,max-mtu" property which is both unused in the kernel and
undocumented. Most likely they are leftovers from downstream.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add gpio0 controller node and correct DMA handshake ID for SPI
tx and rx channels.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add VGIC maintenance interrupt and interrupt-parent property for
interrupt controller, required to run Linux in virtualized environment.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The ahb reset is deasserted in probe before first register access, while the
stmmacheth-ocp reset needs to be asserted every time before changing the phy
mode in Arria10[1].
Changed in Upstream to "ahb"(331085a423 arm64: dts: socfpga: change the
reset-name of "stmmaceth-ocp" to "ahb" ).This change was intended for arm64
socfpga and it is not applicable to Arria10.
Further with STMMAC-SELFTEST Driver enabled, ethtool test also FAILS.
$ ethtool -t eth0
[ 322.946709] socfpga-dwmac ff800000.ethernet eth0: entered promiscuous mode
[ 323.374558] socfpga-dwmac ff800000.ethernet eth0: left promiscuous mode
The test result is FAIL
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -110
3. MMC Counters -110
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC -110
7. MC Filter -110
8. UC Filter 0
9. Flow Control -110
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame -110
30. Multichannel Jumbo -95
31. Split Header -95
32. TBS (ETF Scheduler) -95
[ 324.881327] socfpga-dwmac ff800000.ethernet eth0: Link is Down
[ 327.995360] socfpga-dwmac ff800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Link:[1] https://www.intel.com/content/www/us/en/docs/programmable/683711/21-2/functional-description-of-the-emac.html
Fixes: 331085a423 ("arm64: dts: socfpga: change the reset-name of "stmmaceth-ocp" to "ahb")
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The properties #address-cells and #size-cells are only useful if there
is a ranges property or child nodes with "reg" properties.
This fixes a W=1 warning:
arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts:51.22-72.4: Warning (avoid_unnecessary_addr_size): /soc/i2c@ffc04000/stmpe811@41: unnecessary #address-cells/#size-cells without "ranges", "dma-ranges" or child "reg" property
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
