Add dts nodes for 6 EHRPWM instances on SoC. Disable EHRPWM nodes in the
dtsi files and only enable the ones that are actually pinned out on a
given board.
Includes a minor formatting fixup for the serdes node to line up the
nodes appropriately.
Signed-off-by: Vijay Pothukuchi <vijayp@ti.com>
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221107070009.11500-2-r-ravikumar@ti.com
McASP nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the McASP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-12-afd@ti.com
Mailbox nodes defined in the top-level AM65x SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-11-afd@ti.com
PCIe nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.
As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-10-afd@ti.com
MCAN nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-9-afd@ti.com
MDIO nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-8-afd@ti.com
Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).
Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-7-afd@ti.com
ECAP nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-6-afd@ti.com
EPWM nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-5-afd@ti.com
SPI nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-4-afd@ti.com
I2C nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-3-afd@ti.com
UART nodes defined in the top-level AM65x SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-2-afd@ti.com
I2C nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-13-afd@ti.com
MCAN nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-12-afd@ti.com
Mailbox nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-11-afd@ti.com
Mailbox nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-10-afd@ti.com
Mailbox nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-9-afd@ti.com
UART nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-8-afd@ti.com
I2C nodes defined in the top-level J7200 SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-7-afd@ti.com
UART nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-6-afd@ti.com
MCAN nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-5-afd@ti.com
MCASP nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCASP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-4-afd@ti.com
I2C nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-3-afd@ti.com
UART nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-2-afd@ti.com
OSPI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-11-afd@ti.com
SDHCI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-10-afd@ti.com
MCAN nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-9-afd@ti.com
MDIO nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-8-afd@ti.com
Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).
Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-7-afd@ti.com
ECAP nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-6-afd@ti.com
EPWM nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-5-afd@ti.com
SPI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-4-afd@ti.com
I2C nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-3-afd@ti.com
UART nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-2-afd@ti.com
The GPMC node defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless it is extended with pinmux information.
As the pinmux is only known at the board integration level, this node
should only be enabled when provided with this information.
Disable the GPMC node in the dtsi file. Since the ELM is made to work
with the GPMC, disable it too.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-11-afd@ti.com
MCAN nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-10-afd@ti.com
MDIO nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes (in both CPSW and ICSSG) in the dtsi files and
only enable the ones that are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-9-afd@ti.com
Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).
Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-8-afd@ti.com
PCIe nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.
As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-7-afd@ti.com
ECAP nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-6-afd@ti.com
EPWM nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-5-afd@ti.com
SPI nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-4-afd@ti.com
I2C nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-3-afd@ti.com
UART nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-2-afd@ti.com
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Use BPF CO-RE (Compile Once, Run Everywhere) to support old kernels
when using bperf (perf BPF based counters) with cgroups.
- Support HiSilicon PCIe Performance Monitoring Unit (PMU), that
monitors bandwidth, latency, bus utilization and buffer occupancy.
Documented in Documentation/admin-guide/perf/hisi-pcie-pmu.rst.
- User space tasks can migrate between CPUs, so when tracing selected
CPUs, system-wide sideband is still needed, fix it in the setup of
Intel PT on hybrid systems.
- Fix metricgroups title message in 'perf list', it should state that
the metrics groups are to be used with the '-M' option, not '-e'.
- Sync the msr-index.h copy with the kernel sources, adding support for
using "AMD64_TSC_RATIO" in filter expressions in 'perf trace' as well
as decoding it when printing the MSR tracepoint arguments.
- Fix program header size and alignment when generating a JIT ELF in
'perf inject'.
- Add multiple new Intel PT 'perf test' entries, including a jitdump
one.
- Fix the 'perf test' entries for 'perf stat' CSV and JSON output when
running on PowerPC due to an invalid topology number in that arch.
- Fix the 'perf test' for arm_coresight failures on the ARM Juno
system.
- Fix the 'perf test' attr entry for PERF_FORMAT_LOST, adding this
option to the or expression expected in the intercepted
perf_event_open() syscall.
- Add missing condition flags ('hs', 'lo', 'vc', 'vs') for arm64 in the
'perf annotate' asm parser.
- Fix 'perf mem record -C' option processing, it was being chopped up
when preparing the underlying 'perf record -e mem-events' and thus
being ignored, requiring using '-- -C CPUs' as a workaround.
- Improvements and tidy ups for 'perf test' shell infra.
- Fix Intel PT information printing segfault in uClibc, where a NULL
format was being passed to fprintf.
* tag 'perf-tools-for-v6.1-2-2022-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (23 commits)
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf auxtrace arm64: Add support for parsing HiSilicon PCIe Trace packet
perf auxtrace arm64: Add support for HiSilicon PCIe Tune and Trace device driver
perf auxtrace arm: Refactor event list iteration in auxtrace_record__init()
perf tests stat+json_output: Include sanity check for topology
perf tests stat+csv_output: Include sanity check for topology
perf intel-pt: Fix system_wide dummy event for hybrid
perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
perf test: Fix attr tests for PERF_FORMAT_LOST
perf test: test_intel_pt.sh: Add 9 tests
perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
perf test: test_intel_pt.sh: Add jitdump test
perf test: test_intel_pt.sh: Tidy some alignment
perf test: test_intel_pt.sh: Print a message when skipping kernel tracing
perf test: test_intel_pt.sh: Tidy some perf record options
perf test: test_intel_pt.sh: Fix return checking again
perf: Skip and warn on unknown format 'configN' attrs
perf list: Fix metricgroups title message
perf mem: Fix -C option behavior for perf mem record
perf annotate: Add missing condition flags for arm64
...
Pull Kbuild fixes from Masahiro Yamada:
- Fix CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y compile error for the
combination of Clang >= 14 and GAS <= 2.35.
- Drop vmlinux.bz2 from the rpm package as it just annoyingly increased
the package size.
- Fix modpost error under build environments using musl.
- Make *.ll files keep value names for easier debugging
- Fix single directory build
- Prevent RISC-V from selecting the broken DWARF5 support when Clang
and GAS are used together.
* tag 'kbuild-fixes-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
kbuild: fix single directory build
kbuild: add -fno-discard-value-names to cmd_cc_ll_c
scripts/clang-tools: Convert clang-tidy args to list
modpost: put modpost options before argument
kbuild: Stop including vmlinux.bz2 in the rpm's
Kconfig.debug: add toolchain checks for DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
Kconfig.debug: simplify the dependency of DEBUG_INFO_DWARF4/5
Pull more clk updates from Stephen Boyd:
"This is the final part of the clk patches for this merge window.
The clk rate range series needed another week to fully bake. Maxime
fixed the bug that broke clk notifiers and prevented this from being
included in the first pull request. He also added a unit test on top
to make sure it doesn't break so easily again. The majority of the
series fixes up how the clk_set_rate_*() APIs work, particularly
around when the rate constraints are dropped and how they move around
when reparenting clks. Overall it's a much needed improvement to the
clk rate range APIs that used to be pretty broken if you looked
sideways.
Beyond the core changes there are a few driver fixes for a compilation
issue or improper data causing clks to fail to register or have the
wrong parents. These are good to get in before the first -rc so that
the system actually boots on the affected devices"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (31 commits)
clk: tegra: Fix Tegra PWM parent clock
clk: at91: fix the build with binutils 2.27
clk: qcom: gcc-msm8660: Drop hardcoded fixed board clocks
clk: mediatek: clk-mux: Add .determine_rate() callback
clk: tests: Add tests for notifiers
clk: Update req_rate on __clk_recalc_rates()
clk: tests: Add missing test case for ranges
clk: qcom: clk-rcg2: Take clock boundaries into consideration for gfx3d
clk: Introduce the clk_hw_get_rate_range function
clk: Zero the clk_rate_request structure
clk: Stop forwarding clk_rate_requests to the parent
clk: Constify clk_has_parent()
clk: Introduce clk_core_has_parent()
clk: Switch from __clk_determine_rate to clk_core_round_rate_nolock
clk: Add our request boundaries in clk_core_init_rate_req
clk: Introduce clk_hw_init_rate_request()
clk: Move clk_core_init_rate_req() from clk_core_round_rate_nolock() to its caller
clk: Change clk_core_init_rate_req prototype
clk: Set req_rate on reparenting
clk: Take into account uncached clocks in clk_set_rate_range()
...
