Qualcomm ARM64 DT updates for v5.19
This adds MDIO bus description on the IPQ6018 platform.
On MSM8916 the BAM-DMUX WWAN network device is added and the Huawei
Ascend G7 gains sound card definition and clarified installation
instructions.
MSM8992 and MSM8994 continues to be worked on, gaining multimedia clock
controller, on-chip memory, watchdog and various cleanup changes. The
Xiaomi Mi 4C gains CPU regulators and fixes to the framebuffer
definition, while Huawei Nexus 6P gains eMMC support.
On MSM8996 the modem and sensor remtoeprocs are added and enabled in the
Dragonboard 820c and the Xiaomi devices.
On MSM8998 a few newly added clocks related to the sensor subsystem bus
are marked as protected by default and the OnePlus devices gains NFC.
The SC7180 platform and devices thereon are further polished and
limozeen moves to using edp-panel for EDID-based detection, over
statically defined panels.
On SC7280 GPI DMA, WiFi remoteproc and network device, LPASS audio
clocks, resets for SDCC controllers and a new CRD revision are added. A
supply glitch on the PCIe power and a current leak for Bluetooth during
suspend are corrected. The Herobrine board gains eDP support and the IDP
gains backlight. USB is marked wakeup capable.
On SDM845 the IPA, WLED based backlight and second WiFi channel are
enabled for Xiaomi Pocophone F1, the firmware name is modified to not
conflict with other boards. On RB3 the CAN bus controller is added and
the WiFi calibration variant is defined to allow adding the board's
calibration information into linux-firmware.
SM6350 gains I2C busses, UFS and WiFi support, and the numbering of
uart9 is corrected.
On SM7225 and the Fairphone 4 UFS, WiFi and haptics are enabled.
On SM8150 PCIe, Ethernet and uSD card support is added, and enabled for
the SA8155p ADP board. The PDC interrupt controller is also added and
described as wakup interrupt parent for TLMM.
Camera subsystem and control interface are defined for SM8250. On the
Sony Xperia 1 II the audio amplifiers are enabled.
On SM8350 GPI DMA engines are added and linked to the I2C and SPI
serial engines. Surface Duo 2 gains battery charger support.
On SM8450 the two PCIe controller/PHYs are enabled, GPI DMA and QUP
serial engine instances are added. Remoteproc instances are enabled on
SM8450 HDK.
Last, but not least, a number of DeviceTree validation errors across
various boards are corrected.
* tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (150 commits)
arm64: dts: qcom: Only include sc7180.dtsi in sc7180-trogdor.dtsi
arm64: dts: qcom: sc7180-trogdor: Simplify spi0/spi6 labeling
arm64: dts: qcom: sc7180-trogdor: Simplify trackpad enabling
arm64: dts: qcom: sc7280: eDP for herobrine boards
arm64: dts: qcom: sa8155p-adp: Disable multiple Tx and Rx queues for ethernet IP
arm64: dts: qcom: sm8150: Fix iommu sid value for SDC2 controller
arm64: dts: qcom: sm8350-duo2: enable battery charger
arm64: dts: qcom: Enable pm8350c pwm for sc7280-idp2
arm64: dts: qcom: pm8350c: Add pwm support
arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7180: Remove ipa interconnect node
arm64: dts: qcom: sc7280-idp: Enable GPI DMAs
arm64: dts: qcom: sc7280: Add GENI I2C/SPI DMA channels
arm64: dts: qcom: sc7280: Add GPI DMAengines
arm64: dts: qcom: sm8450: Fix qmp phy node (use phy@ instead of lanes@)
arm64: dts: qcom: db845c: Add support for MCP2517FD
arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
arm64: dts: qcom: sc7280: Add SAR sensors to herobrine crd
arm64: dts: qcom: sm8250: camss: Add CCI definitions
...
Link: https://lore.kernel.org/r/20220509204451.325675-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM DT updates for v5.19
This contains a long overdue overhaul of the MSM8974 DeviceTrees,
aligning the style, structure and naming with what we've learned since
the introduction of this platform.
On top of this the Sony Rhine platform gained I2C masters, NFC and
pstore support and the Fairphone 2 gained touchscreen support.
For the new SDX65 platform reserved-memory nodes, rpmpd, SPMI, CPU
clocks, SDHCI controller, SMMU and TCSR mutex was added. As was the
initial DeviceTree for the related PMX65 PMIC.
MSM8226 gained VADC and RTC support and support for the ASUS ZenWatch 2
was added.
* tag 'qcom-dts-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (62 commits)
ARM: dts: qcom: msm8974-FP2: Add supplies for remoteprocs
ARM: dts: qcom: msm8974-FP2: Configure charger
ARM: dts: qcom: msm8974-FP2: Add support for touchscreen
ARM: dts: qcom: sdx55: Remove ipa interconnect node
ARM: dts: qcom: msm8974: Add missing license headers
ARM: dts: qcom: msm8974-FP2: Add mmc* aliases
ARM: dts: qcom: msm8974-FP2: We're msm8974pro
ARM: dts: qcom-msm8974*: Remove unnecessary include
ARM: dts: qcom-msm8974-rhine: Add pstore node
ARM: dts: qcom-msm8974-rhine: Add NFC and enable I2C hosts
ARM: dts: qcom-msm8974*: Clean up old GPIO declarations
ARM: dts: qcom-msm8974*: Consolidate I2C/UART/SDHCI
ARM: dts: qcom-msm8974*: Enable IMEM unconditionally
ARM: dts: qcom-msm8974: Sort and clean up nodes
ARM: dts: qcom-msm8974: Convert ADSP to a MMIO device
ARM: dts: qcom-msm8974pro-*: Use the 8974pro name in DT filenames
ARM: dts: qcom-msm8974pro: Use &labels
ARM: dts: qcom-msm8974-castor: Use &labels
ARM: dts: qcom-msm8974-{"hon","am"}ami: Commonize and modernize the DTs
ARM: dts: qcom-msm8974-klte: Use &labels
...
Link: https://lore.kernel.org/r/20220509172125.313259-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Keystone2 device tree updates for v5.19
* Cleanups for SPI NOR / flash
* tag 'ti-keystone-dt-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
ARM: dts: keystone: Fix missing fallback and case in SPI NOR node compatible
ARM: dts: keystone: Align SPI NOR node name with dtschema
Link: https://lore.kernel.org/r/20220507163435.tcg46cacwqhe7n64@busily
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v5.19-rc1
This adds some improvements on Tegra234 (QSPI, CCPLEX), improves the
SDMMC clock speed on Tegra194 and adds the ASRC audio block on various
chip generations. Memory controller channels are also added on Tegra186
and later and the missing DFLL reset is added for Tegra210.
* tag 'tegra-for-5.19-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add missing DFLL reset on Tegra210
arm64: tegra: Add memory controller channels
arm64: tegra: Enable ASRC on various platforms
arm64: tegra: Add ASRC device on Tegra186 and later
arm64: tegra: Update PWM fan node name
arm64: tegra: Add node for Tegra234 CCPLEX cluster
arm64: tegra: Add QSPI controllers on Tegra234
arm64: tegra: Update SDMMC1/3 clock source for Tegra194
Link: https://lore.kernel.org/r/20220506143005.3916655-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Changes for v5.19-rc1
Updates the memory controller bindings to properly validate the number
of entries in the reg and reg-names properties.
* tag 'tegra-for-5.19-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: memory: tegra: Update validation for reg and reg-names
Link: https://lore.kernel.org/r/20220506143005.3916655-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas DT binding updates for v5.19 (take two)
- Document support for the R-Car V4H SoC and the White Hawk
development board stack,
- Document support for the RZ/V2M SoC and the RZ/V2M Evaluation Kit
Board,
- Document SPI Multi I/O Bus Controller (RPC-IF) support for RZ/G2UL,
- Miscellaneous fixes and improvements.
* tag 'renesas-dt-bindings-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: soc: renesas: Move renesas,rzg2l-sysc from arm to soc
dt-bindings: memory: renesas,rpc-if: Document RZ/G2UL SoC
dt-bindings: arm: renesas: Document Renesas RZ/V2M SoC and EVK board
dt-bindings: power: renesas,rcar-sysc: Document r8a779g0 SYSC bindings
dt-bindings: reset: renesas,rst: Document r8a779g0 reset module
dt-bindings: arm: renesas: Document R-Car V4H White Hawk DT bindings
Link: https://lore.kernel.org/r/cover.1651828616.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas ARM DT updates for v5.19 (take two)
- I2C, sound, USB, CANFD, timer, watchdog, (Q)SPI, cpufreq, and
thermal support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- Initial support for the R-Car V4H SoC and the Renesas White Hawk
development board stack,
- DMA, RTC, and USB support for the RZ/N1D SoC,
- Initial support for the RZ/V2M SoC an the RZ/V2M Evaluation Kit
Board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (40 commits)
arm64: dts: renesas: Add initial device tree for RZ/V2M EVK
arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY
ARM: dts: r9a06g032: Add USB PHY DT support
ARM: dts: r9a06g032: Add internal PCI bridge node
ARM: dts: r9a06g032: Describe the RTC
arm64: dts: renesas: Add interrupt-names to CANFD nodes
arm64: dts: renesas: r9a07g043: Add SPI Multi I/O Bus controller node
arm64: dts: renesas: r9a07g043: Create thermal zone to support IPA
arm64: dts: renesas: r9a07g043: Add TSU node
arm64: dts: renesas: r9a07g043: Add OPP table
arm64: dts: renesas: r9a07g043: Add RSPI{0,1,2} nodes
arm64: dts: renesas: r9a07g054: Fix external clk node names
arm64: dts: renesas: r9a07g044: Fix external clk node names
ARM: dts: r9a06g032: Fix the NAND controller node
ARM: dts: r9a06g032: Fill the UART DMA properties
ARM: dts: r9a06g032: Describe the DMA router
ARM: dts: r9a06g032: Add the two DMA nodes
arm64: dts: renesas: Remove empty rgb output endpoints
...
Link: https://lore.kernel.org/r/cover.1651828603.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v5.19, part two
1. Cleanups: unused and undocumented dma-channels and dma-requests.
2. Correct compatible of Samsung EEPROM on S5PV210.
* tag 'samsung-dt-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: drop useless 'dma-channels/requests' properties
ARM: dts: s5pv210: drop useless 'dma-channels/requests' properties
ARM: dts: exynos: add atmel,24c128 fallback to Samsung EEPROM
Link: https://lore.kernel.org/r/20220506081438.149192-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor cleanup of ARM DTS for v5.19, part two
Align SPI NOR node names to DT schema and drop unused/undocumented
dma-channels/dma-requests.
* tag 'dt-cleanup-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: socfpga: drop useless 'dma-channels/requests' properties
ARM: dts: zynq-7000: drop useless 'dma-channels/requests' properties
ARM: dts: marvell: align SPI NOR node name with dtschema
ARM: dts: omap: align SPI NOR node name with dtschema
ARM: dts: nuvoton: align SPI NOR node name with dtschema
Link: https://lore.kernel.org/r/20220506081438.149192-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor cleanup of ARM64 DTS for v5.19
Align SPI NOR node names and freq-table-hz to DT schema. Drop
unused/undocumented dma-channels/dma-requests.
* tag 'dt64-cleanup-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: broadcom: drop useless 'dma-channels/requests' properties
arm64: dts: stratix10/agilex: drop useless 'dma-channels/requests' properties
arm64: dts: marvell: align SPI NOR node name with dtschema
arm64: dts: microchip: align SPI NOR node name with dtschema
arm64: dts: hisilicon: align 'freq-table-hz' with dtschema in UFS
Link: https://lore.kernel.org/r/20220506081438.149192-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UART 0 to 2 do not have DMA support, while UART 3 to 7 do.
Fill the "dmas" and "dma-names" properties for each of these nodes.
Please mind that these nodes go through the dmamux node which will
redirect the requests to the right DMA controller. The first 4 cells of
the "dmas" properties will be transferred as-is to the DMA
controllers. The last 2 cells are consumed by the dmamux. Which means
cell 0 and 4 are almost redundant, one giving the controller request ID
and the other the dmamux channel which is a 1:1 translation of the
request IDs, shifted by 16 when pointing to the second DMA controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220421095323.101811-11-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SoC is always present on sc7180-trogdor.dtsi and thus we should
include it in the "generic" dtsi file for trogdor. Previously we had
removed it from there because we had to do the spi6/spi0 swizzle, so
each trogdor variant board had to include sc7180.dtsi and then
sc7180-trogdor.dtsi so that the latter dtsi file could modify the right
spi bus for EC and H1 properties that are common to all trogdor boards.
Now that we're done with that we can replace sc7180.dtsi includes with
sc7180-trogdor.dtsi and include sc7180.dtsi in sc7180-trogdor.dtsi as
was originally intended. We still need to include sc7180-trogdor.dtsi
before the bridge dtsi files though because those rely on the panel
label.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-4-swboyd@chromium.org
We had to do this spi0/spi6 flip-flop on trogdor-r0 because the spi
buses got swizzled between r0 and r1. The swizzle stopped after r1, but
we kept this around to support either hardware possibility and to keep
trogdor-r0 working.
trogdor-r0 isn't supported upstream, so this swizzle is not doing
anything besides making a pattern that others tryt to copy for the EC and
H1 nodes. Let's remove it and simplify the dts files.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-3-swboyd@chromium.org
Add eDP support to herobrine boards, splitting up amongst the
different files as makes sense. Rationale for the current split of
things:
* The eDP connector itself is on qcard. However, not all devices with
a qcard will use an eDP panel. Some might use MIPI and, presumably,
someone could build a device with qcard that had no display at all.
* The qcard provides a PWM for backlight that goes to the eDP
connector. This PWM is also provided to the board and it's expected
that it would be used as the backlight PWM even for herobrine
devices with MIPI displays.
* It's currently assumed that all herobrine boards will have some sort
of display, either MIPI or eDP (but not both).
* We will assume herobrine-rev1 has eDP. The schematics allow for a
MIPI panel to be hooked up but, aside from some testing, nobody is
doing this and most boards don't have all the parts stuffed for
it. The two panels would also share a PWM for backlight, which is
weird.
* herobrine-villager and herobrine-hoglin (crd) also have eDP.
* herobrine-hoglin (crd) has slightly different regulator setup for
the backlight. It's expected that this is unique to this board. See
comments in the dts file.
* There are some regulators that are defined in the qcard schematic
but provided by the board like "vreg_edp_bl" and
"vreg_edp_3p3". While we could put references to these regulators
straight in the qcard.dtsi file, this would force someone using
qcard that didn't provide those regulators to provide a dummy or do
an ugly /delete-node/. Instead, we'll add references in
herobrine.dtsi.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220426124053.v2.1.Iedd71976a78d53c301ce0134832de95a989c9195@changeid
Fix the issues seen with ethernet traffic getting stalled on SA8155p-ADP
board with default (or larger) mtu size of 1500 bytes, by disabling
multiple Tx and Rx queues for the stmmac IP block.
With the single queue setup, the ethernet traffic is stable,
wget / curl can work well on the board and no ethernet stall is
observed even when longer netperf / iperf3 test are run. Also
a performance of ~940 Mbits/sec is observed on the 1G link, so
there is no observable degradation in performance as well.
Fixes: c5cb42cc84 ("arm64: dts: qcom: sa8155p-adp: Enable ethernet node")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220423195003.353150-1-bhupesh.sharma@linaro.org
