i.MX arm64 device tree change for 6.1:
- New board support: i.MX8DXL EVK, Kontron SL/BL i.MX8MM OSM-S, i.MX8MM
Gateworks GW7904, MSC SM2S-IMX8PLUS SoM and carrier board, NXP
LS2081ARDB.
- Update i.MX8MQ device tree to use generic name 'dma-controller' for
SDMA.
- A number of i.MX8ULP device tree improvements and updates: correct
parent clock of LPI2C & LPSPI, increase the clock speed of LPSPI, add
PMU and mailbox device, drop undocumented CGC property, enable FEC, etc.
- Add interconnect property for various i.MX8MP blk-ctrl devices.
- Enable VPU PGC, blk-ctrl and PCIe support for i.MX8MP SoC.
- A set of changes from Peng Fan to add various devices for i.MX93 SoC,
including MU, blk-ctrl, PMU, LPI2C, LPSPI, SRC, etc.
- Two set of changes to update LS1043A and LS1046A device trees on
various aspects, including USB3, PCIe, DMA, mdio-mux, QSPI Flash, etc.
- Board imx8mq-librem5 update: add USB role switching, add RGB PWM
notification LEDs, add voice coil motor for focus control, fix MIPI_CSI
description.
- A series from Frieder Schrempf to improve imx8mm-kontron device trees
for VSELECT switch, DDRC operating point, SPI NOR partition layout etc.
- A set of display and PMIC related additions and improvements on
imx8mm-verdin board.
- A number of i.MX8M Plus DHCOM PDK2 device tree improvments from Marek
Vasut.
- A few imx8mp-venice device tree updates on USB, cpufreq and WiFi/BT.
- A series from Vladimir Oltean to enable multiple switch CPU ports
support.
- Other small and random board specific updates.
* tag 'imx-dt64-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (90 commits)
arm64: dts: ls1046a-qds: Modify the qspi flash frequency
arm64: dts: ls1046a-qds: add mmio based mdio-mux nodes for FPGA
arm64: dts: ls1046a: add gpios based i2c recovery information
arm64: dts: ls1046a: use a pseudo-bus to constrain usb and sata dma size
arm64: dts: ls1046a: make dma-coherent global to the SoC
arm64: dts: ls1046a: add missing dma ranges property
arm64: dts: ls1046a: Add big-endian property for PCIe nodes
arm64: dts: ls1046a: Add the PME interrupt and big-endian to PCIe EP nodes
arm64: dts: ls1046a: Enable usb3-lpm-capable for usb3 node
arm64: dts: ls1043a-rdb: add pcf85263 rtc node
arm64: dts: ls1043a-qds: add mmio based mdio-mux support
arm64: dts: ls1043a: use a pseudo-bus to constrain usb and sata dma size
arm64: dts: ls1043a: add gpio based i2c recovery information
arm64: dts: ls1043a: make dma-coherent global to the SoC
arm64: dts: ls1043a: add missing dma ranges property
arm64: dts: ls1043a: Add big-endian property for PCIe nodes
arm64: dts: ls1043a: Add SCFG phandle for PCIe nodes
arm64: dts: ls1043a: use pcie aer/pme interrupts
arm64: dts: ls1043a: Enable usb3-lpm-capable for usb3 node
arm64: dts: ls1043a: fix the wrong size of dcfg space
...
Link: https://lore.kernel.org/r/20220918092806.2152700-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree change for 6.1
- A series from Alexander Stein to add missing properties for i.MX6 SRAM.
- Drop 'interrupts' property when 'interrupts-extended' is present. This
fixes a dtbs_check warning with i.MX6 DT.
- Update device trees to use generic name 'dma-controller' for SDMA.
- A set of changes from Krzysztof Kozlowski to align SPI, LED and
gpio-keys node name with dtschema.
- A series of indentation and white-space cleanups from Marcel Ziswiler
to address various checkpatch warnings.
- Add DDR pinmux defines to VF610 DT header.
- A couple of changes from Peng Fan to update clock-names and add IPG
clock for i.MX7ULP LPI2C devices.
- Improve device tree structure for Kontron i.MX6UL/ULL based boards.
- A series of changes from Tim Harvey to add CAN regulator for Gateworks
i.MX6QDL boards.
- Various small and random board specific updates.
* tag 'imx-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (40 commits)
ARM: dts: imx6qdl-gw54xx: add CAN regulator
ARM: dts: imx6qdl-gw53xx: add CAN regulator
ARM: dts: imx6qdl-gw52xx: add CAN regulator
ARM: dts: imx: update sdma node name format
ARM: dts: imx6: skov: migrate to resistive-adc-touch
ARM: dts: imx6sx-udoo-neo: don't use multiple blank lines
ARM: dts: imx6sl: use tabs for code indent
ARM: dts: imx6sx: add missing properties for sram
ARM: dts: imx6sll: add missing properties for sram
ARM: dts: imx6sl: add missing properties for sram
ARM: dts: imx6qp: add missing properties for sram
ARM: dts: imx6dl: add missing properties for sram
ARM: dts: imx6q: add missing properties for sram
ARM: dts: imx7ulp: Add IPG clock for lpi2c
ARM: dts: imx7ulp: update the LPI2C clock-names
ARM: dts: vf610: ddr pinmux
ARM: dts: imx6qdl-dhcom: Move IPU iomux node from PDK2 to SoM file
ARM: dts: imx6ul-kontron: Add imx6ull-kontron-bl to Makefile
ARM: dts: imx6ul-kontron: Simplify devicetree structure
ARM: dts: vf610: align SPI node name with dtschema
...
Link: https://lore.kernel.org/r/20220918092806.2152700-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v6.1-rc1
These changes enable PCI, Ethernet and HDA support on Jetson AGX Orin.
DMA support is enabled for I2C on a number of SoC generations and the
Google Pixel C (a.k.a. Smaug) device receives Bluetooth and Wi-Fi
support.
Other than that this also contains some minor cleanups and fixes.
* tag 'tegra-for-6.1-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add GPCDMA support for Tegra I2C
arm64: tegra: Add iommus for HDA on Tegra234
arm64: tegra: Enable HDA node for Jetson AGX Orin
arm64: tegra: Add context isolation domains on Tegra234
arm64: tegra: Fixup iommu-map property formatting
arm64: dts: tegra: smaug: Add Wi-Fi node
arm64: dts: tegra: smaug: Add Bluetooth node
arm64: tegra: Enable MGBE on Jetson AGX Orin Developer Kit
arm64: tegra: Add MGBE nodes on Tegra234
arm64: tegra: Fix up compatible for Tegra234 GPCDMA
arm64: tegra: Enable PCIe slots in P3737-0000 board
arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT
arm64: tegra: Add regulators required for PCIe
Link: https://lore.kernel.org/r/20220916101957.1635854-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Changes for v6.1-rc1
Adds device tree bindings for the MGBE found on Tegra234 SoCs, as well
as stream IDs for the shared host1x context devices.
* tag 'tegra-for-6.1-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Add Host1x context stream IDs on Tegra234
dt-bindings: net: Add Tegra234 MGBE
Link: https://lore.kernel.org/r/20220916101957.1635854-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AT91 DT for v6.1 #2
It contains:
- new SAMA5D3 based board, namely SAMA5D3-EDS
- adjustments to pass the DT binding validations
- disable AES on some LAN966 based boards as they are reserverd by
secure OS
* tag 'at91-dt-6.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
spi: dt-bindings: atmel,at91rm9200-spi: Add DMA related properties
ARM: dts: at91: Add `atmel,usart-mode` required property to serial nodes
ARM: dts: at91: sam9x60ek: Add DBGU compatibles to uart1
ARM: dts: at91: sama7g5: Swap rx and tx for spi11
dts: arm: at91: Add SAMA5D3-EDS Board
dt-bindings: arm: at91: Add info on SAMA5D3-EDS
ARM: dts: lan966x: disable aes
Link: https://lore.kernel.org/r/20220916105407.1287452-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The qspi flash in ls1046a QDS board can operate at 50MHz frequency.
Therefore, update the maximum supported freq in dts file.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is mmio based mdio mux function in the FPGA device on ls1046a-qds
board. Add the mmio based mdio-mux nodes to ls1043a-qds boards and
add simple-mfd as a compatbile for the FPGA node to reflect the
multi-function nature of it.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add scl-gpios property for i2c recovery and add SoC specific
compatible string for SoC specific fixup.
Signed-off-by: Zhang Ying <ying.zhang22455@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Wrap the usb and sata controllers in an intermediate simple-bus and use
it to constrain the dma address size of these usb controllers to the 40
bits that they generate toward the interconnect. This is required
because the SoC uses 48 bits address sizes and this mismatch would lead
to smmu context faults because the usb generates 40-bit addresses while
the smmu page tables are populated with 48-bit wide addresses.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These SoCs are really completely dma coherent in their entirety so add
the dma-coherent property at the soc level in the device tree and drop
the instances where it's specifically added to a few select devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These chips have a 48-bit address size so make sure that the dma-ranges
reflects this. Otherwise the linux kernel's dma sub-system will set
the default dma masks to full 64-bit, badly breaking dmas.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing node for rtc device under i2c and fix style problems at
the same time.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is mmio based mdio mux function in the FPGA device on ls1043a-qds
board. Add the mmio based mdio-mux nodes to ls1043a-qds boards and
add simple-mfd as a compatbile for the FPGA node to reflect the
multi-function nature of it. Also connect the ethernet interfaces to
these phy interfaces.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Wrap the usb and sata controllers in an intermediate simple-bus and use
it to constrain the dma address size of these usb controllers to the 40
bits that they generate toward the interconnect. This is required
because the SoC uses 48 bits address sizes and this mismatch would lead
to smmu context faults because the usb generates 40-bit addresses while
the smmu page tables are populated with 48-bit wide addresses.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add scl-gpios property for i2c recovery and add SoC specific compatible
string for SoC specific fixup.
Signed-off-by: Zhang Ying <ying.zhang22455@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1043a is really completely dma coherent in their entirety so add the
dma-coherent property at the soc level in the device tree and drop the
instances where it's specifically added to a few select devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1043a has a 48-bit address size so make sure that the dma-ranges
reflects this. Otherwise the linux kernel's dma sub-system will set the
default dma masks to full 64-bit, badly breaking dmas.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the big-endian property for LS1043A PCIe nodes for accessing PEX_LUT
and PF register block.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1043A PCIe controller has some control registers
in SCFG block, so add the SCFG phandle for each PCIe
controller node.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After the binding has been updated to include more specific interrupt
definition, update the dts to use the more specific interrupt names.
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
NXP Erratum A008585 affects A57 core cluster used in LS2085 rev1.
However this problem has been fixed in A72 core cluster used in LS2088.
Therefore remove the erratum from LS2088A. Keeping it only in LS2085.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Sandeep Malik <sandeep.malik@nxp.com>
Acked-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify a channel zero in idle state to avoid enterring tri-stated state
for PCA9547.
Some information about E-00013:
- Description: I2C1 and I2C3 buses are missing pull-up.
- Impact: When the PCA954x device is tri-stated, the I2C bus will float.
This makes the I2C bus and its associated downstream devices
inaccessible.
- Hardware fix: Populate resistors R189 and R190 for I2C1 and resistors
R228 and R229 for I2C3.
- Software fix: Remove the tri-state option from the PCA954x
driver(PCA954x always on enable status, specify a channel zero in dts to
fix the errata E-00013).
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the cpld node name to be generic board-contrl and add mmio mdio
mux nodes from the on-board FPGA.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCIe support on the Gateworks GW74xx board. While at it,
fix the related gpio line names from the previous incorrect values.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is to support the EVK (Evaluation Kit Board) for the i.MX8DXL.
The patch has enabled the serial console, SD/EMMC interface, and
the eqos and fec ethernet network.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.
This patch adds the basic support for i.MX8DXL SoC.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ddr-pmu on i.mx8dxl has a different interrupt number.
Add a node label to ddr-pmu so that it could be referred
and changed in i.mx8dxl dts.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW74xx supports an on-board Laird Connectivity Sterling LWB5+ module
which uses a Cypress CYW4373W chip to provide 1x1 802.11 a/b/g/n/ac +
Bluetooth 5.2.
Add the proper device-tree nodes for it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add regulator config for cpu-supply in order to support cpufreq.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for USB DR on USB1 interface. Host/Device detection is done
using the usb-role-switch connector with a GPIO as USB1_OTG_ID is not
connected internally.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit "arm64: dts: ls1028a: enable swp5 and eno3 for all boards" which
Shawn declared as applied, but for which I can't find a sha1sum, has
enabled a new Ethernet port on the LS1028A-RDB (&enetc_port3), but
U-Boot, which passes a MAC address to Linux' device tree through the
/aliases node, fails to do this for this newly enabled port.
Fix that by adding more ethernet aliases in the only
backwards-compatible way possible: at the end of the current list.
And since it is possible to very easily convert either swp4 or swp5 to
DSA user ports now (which have a MAC address of their own), using these
U-Boot commands:
=> fdt addr $fdt_addr_r
=> fdt rm /soc/pcie@1f0000000/ethernet-switch@0,5/ports/port@4 ethernet
it would be good if those DSA user ports (swp4, swp5) gained a valid MAC
address from U-Boot as well. In order for that to work properly,
provision two more ethernet aliases for &mscc_felix_port{4,5} as well.
The resulting ordering is slightly unusual, but to me looks more natural
than eno0, eno2, swp0, swp1, swp2, swp3, eno3, swp4, swp5.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node names should be generic, so change the sdma node name format 'sdma'
into 'dma-controller'.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
