Pull the whole BDW IPS min CDCLK stuff into the IPS code
so that all the details around IPS are contained in once
place.
Note that while
- min_cdclk = DIV_ROUND_UP(min_cdclk * 100, 95);
vs.
+ min_cdclk = max(DIV_ROUND_UP(crtc_state->pixel_rate * 100, 95), min_cdclk)
may look different, they are in fact the same because
min_cdclk==crtc_state->pixel_rate at this point in
intel_crtc_compute_min_cdclk() on BDW.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029215217.3697-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
On ADLP+ during modeset enabling and disabling, enable and disable the DP2
configuration for MST slave transcoders as required by the specification.
Update the documentation of intel_ddi_config_transcoder_func() /
intel_ddi_disable_transcoder_func() based on the above. While at it also
clarify the programming steps of these functions specific to transcoder
types.
v2:
- Enable/disable the DP2 config from
intel_ddi_config_transcoder_func()/intel_ddi_disable_transcoder_func().
(Jani)
- Handle all ADLP+ platforms in one patch, instead of doing that
separately wrt. PTL.
Bspec: 55424, 54128, 65448, 68849
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030192313.4030617-5-imre.deak@intel.com
On ADLP+ during modeset enabling configure the DDI function without
enabling it for MST slave transcoders before programming the data and
link M/N values. The DDI function gets enabled separately later in the
transcoder enabling sequence.
Align the code with the spec based on the above.
v2: Move this patch earlier in the series, addressing the DP2
config fixes for all ADLP+ platforms later.
Bspec: 55424, 54128, 65448, 68849
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030192313.4030617-3-imre.deak@intel.com
On PTL during modeset enabling configure the DDI function without
enabling it for MST slave transcoders before programming the data and
link M/N values. The DDI function gets enabled separately later in the
transcoder enabling sequence.
This fixes a slave transcoder getting stuck during enabling, leading
to page flip timeout errors on the corresponding pipe.
The spec requires the same programming step for ADLP+ platforms, that
will be addressed separately (on those platforms the above transcoder
getting stuck issue was not observed).
Bspec: 68849
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030192313.4030617-2-imre.deak@intel.com
If the system boots with MBUS joining enabled but we disable
the relevant pipe during sanitation we later get into trouble
as the rest of the code doesn't expect MBUS joining to be
enabled unless the set of active pipes is in agreement.
We could relax some of the MBUS joining related checks during
normal atomic commits to let this slide, but that might also
let some real bugs through. So let's sanitize the MBUS joining
instead. And in order to keep things more or less in sync we'll
do the related credit, cdclk/mdclk ratio, etc. updates as well.
We'll stick to sturct drm_i915_private for now (instead of
struct intel_display) since the rest of the skl wm code does the
same, and we might need to bakport this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241031155646.15165-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We'll be wanting to reprogram the PIPE_MBUS_DBOX_CTL registers
during an upcoming MBUS sanitation stage. Extract the reprogramming
loop into a helper that doesn't depend on the full atomic state
so that it can be reused.
We'll stick to sturct drm_i915_private for now (instead of
struct intel_display) since the rest of the skl wm code does the
same, and we might need to bakport this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241031155646.15165-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Certain resolutions require 12 DSC slices support along with ultrajoiner.
For such cases, the third DSC Engine per Pipe is enabled. Each DSC
Engine processes 1 Slice, resulting in a total of 12 VDSC slices
(4 Pipes * 3 DSC Instances per Pipe).
Add support for 12 DSC slices and 3 DSC engines for such modes.
v2: Add missing check for 3 slices support only with 4 joined pipes.
(Suraj)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030041036.1238006-8-ankit.k.nautiyal@intel.com
According to the DSC spec, the slice width should be chosen such that
the picture width (hactive) is evenly divisible by the slice width.
If not, extra pixels (padding) must be added to the last slice to
ensure all slices have the same width.
Currently, we do not support handling these extra pixels.
Therefore, select a slice count that evenly divides the hactive
(slice_width = hactive / slice_count).
This check is already implemented for DSI, where the slice count is
selected from the BIOS.
For DP, currently with 1, 2, 4 slices per pipe it is unlikely to have
slice count not being able to divide hactive, but with 3 DSC engines
and 3 slices, we can have such cases. Adding this check prepares for
future scenarios where such configurations might be used.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030041036.1238006-7-ankit.k.nautiyal@intel.com
At the moment dsc_split represents whether the dsc splitter is used
or not. With 3 DSC engines, the splitter can split into two streams
or three streams.
Instead of representing the splitter's state, it is more effective to
represent the number of DSC streams per pipe.
Replace the `dsc.dsc_split` member with `dsc.num_streams` to indicate the
number of DSC streams used per pipe. This change will implicitly
convey the splitter's operation mode.
v2: Avoid new enum for dsc split. (Suraj)
v3:
-Replace dsc_split with num_stream. (Suraj)
-Avoid extra parentheses. (Jani)
v4: Set num_streams to 1, if VDSC_JOINER not set while readout.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030041036.1238006-3-ankit.k.nautiyal@intel.com
For some platforms, the maximum slices per DSC engine is 4, while for
others it is 2. Update the comment to reflect this and clarify that
the 'valid_dsc_slicecount' list represents the valid number of slices
per pipe.
Currently, we are working with 1, and 2 slices per DSC engine,
which works for all platforms. With this the number of slices per pipe
can be 1,2 or 4 with different slice & DSC engine configuration.
Add a #TODO for adding support for 4 slices per DSC engine where
supported.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030041036.1238006-2-ankit.k.nautiyal@intel.com
The TRANS_DDI_FUNC_CTL bit used to enable/disable HDCP rekeying
has moved from bit 12 (Xe2) to bit 15 (Xe3); update the RMW
toggle accordingly.
Also drop the misleading workaround comment tag on this function
since disabling of HDCP rekeying is something that happens on
all platforms, not just those impacted by that workaround.
While we're here, also re-order the if/else ladder to use
standard "newest platform first" order.
v2: add additional definition instead of function, commit message typo
fix and update.
v3: restore lost conditional from v2.
v4: subject line and subject message updated, fix the if ladder order,
fix the bit definition order.
v5: Add the bspec link and remove the Wa comment tag
v6: Rebase over new changes
v7: Fix commit subject and message, reladder the if/else blocks
Bspec: 69964
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241104185055.739605-1-suraj.kandpal@intel.com
Changes in Dynamic Range and Mastering infoframe
should not trigger a full modeset. Therefore, allow
fastset. DP SDP programming is already hooked up in the
fastset flow but HDMI AVI infoframe update is not, add it.
Any other infoframe that can be fastset should be added to
the helper intel_hdmi_fastset_infoframes().
v3:
- Create a wrapper intel_ddi_update_pipe_hdmi to stick to
uniform naming (Jani)
- Do not disable HDMI AVI infoframe if already disabled (Uma)
v2:
- Update HDMI AVI infoframe during fastset.
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241023044122.3889137-1-chaitanya.kumar.borah@intel.com
We are currently seeing unexpected link trainings with several different
eDP panels. These are caused by these panels stating bad link status in
their dpcd registers. This can be observed by doing following test:
1. Boot up without Xe module loaded
2. Load Xe module with PSR disabled:
$ modprobe xe enable_psr=0
3. Read panel link status register
$ dpcd_reg read --offset 0x200e --count=1
0x200e: 00
4. Enable PSR, sleep for 2 seconds and disable PSR again:
$ echo 0x1 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
$ echo "-1" > /sys/kernel/debug/dri/0000:00:02.0/xe_params/enable_psr
$ echo 0x0 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
$ sleep 2
$ cat /sys/kernel/debug/dri/0/i915_edp_psr_status | grep status
$ echo 0x1 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
Source PSR/PanelReplay status: DEEP_SLEEP [0x80310030]
5. Now read panel link status registers again:
$ dpcd_reg read --offset 0x200e --count=1
0x200e: 80
Workaround this by not trusting link status registers after PSR is enabled
until first short pulse interrupt is received.
v2:
- clear link_ok flag on pipe disable
- remove useless comment
- modify intel_dp_needs_link_retrain return statement
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029122415.1789528-1-jouni.hogander@intel.com
Currently, even though there is a bit to control FEC enable/disable
individually, the FEC Decode Enable sequence is sent by the SOC only
once TRANS_CONF enable is set. This ties the FEC enabling too tightly
to modeset and therefore cannot be re-issued (in case of failure)
without a modeset.
From PTL, FEC_DECODE_EN sequence can be sent to a DPRX independent
of TRANS_CONF enable. This allows us to re-issue an FEC_DECODE_EN
sequence without a modeset. Hence allowing us to have a retry
mechanism in case the DPRX does not respond with an FEC_ENABLE
within certain amount of time.
While at it, replace struct drm_i915_private with struct intel_display
v4:
- More code refactor [Jani]
- use struct intel_display [Jani]
- Optimize logging [Jani]
v3:
- Make the commit message more legible [Jani]
- Refactor code to re-use existing code [Jani]
- Do away with platform dependent FEC enable checks [Jani]
v2:
- Refactor code to avoid duplication and improve readability [Jani]
- In case of PTL, wait for FEC status directly after FEC enable [Srikanth]
- Wait for FEC_ENABLE_LIVE_STATUS to be cleared before
re-enabling FEC [Srikanth]
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241024061002.4085137-1-chaitanya.kumar.borah@intel.com
From LNL onwards there is a new hardware feature, which
allows to detect if the driver wrongly allocated DBuf
entries and they happen to overlap. If enabled this will
cause a specific interrupt to occur.
We now handle it in the driver, by writing correspondent
error message to kernel log.
v2: Initialize dbuf overlap flag in runtime_defaults (Jani Nikula)
v3: Unmask the overlap detection interrupt (Uma)
v4: use display over i915 (Jani Nikula)
v5: Use display instead of dev_priv (Jani Nikula)
v6: rebased to resolve merge conflicts
Bspec: 69450, 69464
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030103319.207235-1-vinod.govindapillai@intel.com
While updating the source OUI on the sink the driver should avoid
writing the OUI if it's already up-to-date to prevent the sink from
resetting itself in response to the update. On eDP - the only output
type where the OUI was updated so far - the driver ensured this by
comparing the current source OUI DPCD register values with the expected
Intel OUI value, skipping the update in case of a match. On some non-eDP
sinks - at least on Synaptics branch devices - this method doesn't work,
since the source OUI DPCD registers read back as all 0, even after
updating the registers.
Handle the above kind of sinks by tracking when the OUI was updated and
so should be valid, regardless of what the DPCD registers contain.
eDP sinks reset the written source OUI value when the panel power is
disabled, invalidate the OUI state accordingly.
This is required by a follow-up patch updating the source OUI for
non-eDP sink types as well.
v2: Fix setting intel_dp::oui_valid=true, if the DPCD register contains
already the expected value.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-5-imre.deak@intel.com
If the source OUI DPCD register value matches the expected Intel OUI
value, the write timestamp doesn't get updated leaving it at the 0
initial value if the OUI wasn't written before. This can lead to an
incorrect wait duration in intel_dp_wait_source_oui(), since jiffies is
not inited to 0 in general (on a 32 bit system INITIAL_JIFFIES is set to
5 minutes ahead of wrap-around). Fix this by intializing the write
timestamp in the above case as well.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-4-imre.deak@intel.com
The sink's capabilities, like the DSC caps, depend on the source OUI
written to the sink's DPCD registers and so this OUI value should be
valid for the whole duration of the detection. An eDP sink will reset
this OUI value when the panel power is disabled, so prevent the
disabling - happening by default after a 1 sec idle period - for the
whole duration of detection.
v2: Update the documentation for intel_pps_on(). (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-3-imre.deak@intel.com
Make sure that a DP connector detection doesn't happen in parallel
with an ongoing modeset on the connector. The reasons for this are:
- Besides reading the capabilities, EDID etc. the detection may change
the state of the sink (via the AUX bus), for instance by setting the
LTTPR mode or the source OUI (the latter introduced by an upcoming
patch). It's better to avoid such changes affecting an onging modeset
in any way.
- During a modeset's link training any access to DPCD registers, besides
the registers used for link training should be avoided, at least in
the LTTPR non-transparent and transparent link training modes.
Such asynchronous accesses - besides connector detection - can also
happen via the AUX device node for instance, for those a parallel
modeset will have to be avoided in a similar way to the change in this
patch. (A topic for a follow-up change.)
- The source OUI written to an eDP sink is valid only while the panel
power is enabled. A modeset on eDP will enable/disable the panel power
synchronously; this should be prevented in the middle of the connector
detection, to ensure a consistent sink state (which depends on the
source OUI) for the whole duration of detection. The panel power could
still get disabled during detection after an idle period (1 sec), this
will be prevented by the next patch.
v2: (Ville)
- s/wait_for_crtc_hw_done/wait_for_connector_hw_done
- Get drm_device using an intel_display instead of drm_i915_private ptr.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-2-imre.deak@intel.com
Use x100, or ver * 100 + rel, versions for full IP version checks,
similar to what xe driver does:
- Replace IP_VER(14, 1) inline with 1401, etc.
- Convert DISPLAY_VER_FULL() to DISPLAY_VERx100()
- Convert IS_DISPLAY_VER_FULL() to IS_DISPLAY_VERx100()
- Convert IS_DISPLAY_VER_STEP() to IS_DISPLAY_VERx100_STEP()
This makes ver.rel versions easier to use, follows the xe driver
pattern, and drops the dependency on the IP_VER() macro.
v2: Rebase, drop IP_VER() from xe compat headers
v3: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029155536.753413-1-jani.nikula@intel.com
