When the driver was converted from soc_camera software support for
V4L2_FIELD_SEQ_TB and V4L2_FIELD_SEQ_BT were added. This was done by
capturing twice to the same VB2 buffer, but at different offsets.
This turned out to be a bad idea and it never really worked properly in
all situations. As the hardware can't support this mode natively remove
trying to emulate it in software. It's still possible to capture TOP or
BOTTOM fields separately or both ALTERNATING. If user-space wants the
same fields in the same buffer the same hack to capture twice to the
same buffer can be done.
Removing this error prone emulated support pave ways in future work to
simplify the internal buffer handling and making it less fragile, while
enabling adding support for other features the hardware actually
supports.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add multiplexed streams support. CAL has 8 DMA-engines and can capture 8
separate streams at the same time. The driver filters the streams based
on CSI-2 virtual channel number and datatype. CAL may have (depending on
the SoC) two CSI-2 RX blocks, which share the 8 DMA-engines, so the
number of capturable streams does not change even if there are two CSI-2
RX blocks.
Add 8 video device nodes, each representing a single DMA-engine, and set
the number of source pads on CSI-2 RX blocks to 8. Each video node can be
connected to any of the source pads on either of the CSI-2 RX instances
using media links. CSI-2 RX block's subdevice internal routing is used
to route the incoming CSI-2 streams to one of the 8 source pads.
Only video data streams are supported at the moment.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
When v4l2_subdev_init_finalize() fails no changes have been made to
the runtime-pm device state yet, so the probe_error_media_entity_cleanup
rollback path should not touch the runtime-pm device state.
Instead this should be done from the probe_error_v4l2_subdev_cleanup
rollback path. Note the pm_runtime_xxx() calls are put above
the v4l2_subdev_cleanup() call to have the reverse call order of probe().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Fixes: 289c25923e ("media: ov2740: Use sub-device active state")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Extract values needed by ipu6_queue_buf_ready() function from fw abi
structure. This will allow to reuse same buf ready code when fw abi
change.
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Document the CCS PLL flags with short comments. The CCS spec has more
information on them while the added documentation helps finding the
relevant information in the CCS spec.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Print the PLL calculator flags right away when the PLL calculator is
called. Previously this was done only in a successful case and that didn't
really help solving a problem when one happened.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The LINK_DECOUPLED flag isn't used by the PLL calculator other than
printing it. The number of OP/VT lanes are already printed in any case.
Thus drop the flag as it has no function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
In general the CCS PLL calculator prints debugging information on the
process to ease debugging. This case was not annotated, do that now.
Remove an extra multiplication while at it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The PLL calculator does a search of the PLL configuration space for all
valid OP pre-PLL clock dividers. The maximum did not take into account the
CCS PLL flag CCS_PLL_FLAG_EXT_IP_PLL_DIVIDER in which case also odd PLL
dividers (other than 1) are valid. Do that now.
Fixes: 4e1e8d240d ("media: ccs-pll: Add support for extended input PLL clock divider")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The ccs_pll_calculate_vt_tree() function does a search over possible VT
PLL configurations to find the "best" one. If the sensor does not support
odd pre-PLL divisors and the minimum value (with constraints) isn't 1,
other odd values could be errorneously searched (and selected) for the
pre-PLL divisor. Fix this.
Fixes: 415ddd9939 ("media: ccs-pll: Split limits and PLL configuration into front and back parts")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The ccs_pll_calculate() function does a search over possible PLL
configurations to find the "best" one. If the sensor does not support odd
pre-PLL divisors and the minimum value (with constraints) isn't 1, other
odd values could be errorneously searched (and selected) for the pre-PLL
divisor. Fix this.
Fixes: 415ddd9939 ("media: ccs-pll: Split limits and PLL configuration into front and back parts")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The 3840x2160 mode operates with the imx334 reset values.
If we switch to other modes and then return to the 3840x2160 mode,
it should function correctly. so updated the mode_3840x2160_regs
array with the imx334 reset values.
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Optimized the resolution arrays by integrating a common register array.
Adjusted the register array values for 1920x1080@30 and 3840x2160@30
resolutions to align with the common register array values.
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
There was a hardware bug which need IPU6 driver to disable the ATS. This
workaround is not needed anymore as the bug was fixed in hardware level.
Additionally, Arrow Lake has the same IPU6 PCI ID and x86 stepping but
does not have the bug. Removing the Meteor Lake workaround is also
required for the driver to function on Arrow Lake.
Signed-off-by: Hao Yao <hao.yao@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Fixes: 25fedc0219 ("media: intel/ipu6: add Intel IPU6 PCI device driver")
Cc: stable@vger.kernel.org
[Sakari Ailus: Added tags and explanation of what is fixed.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
For continuous PLL lock, it is recommended to extend the temperature
ramp down range of the DS90UB953-Q1 serializer based on the device's
initial temperature [1].
The serializer's die temperature is reported only to the deserializer
through the sensor status registers, and for UB9702, it is recommended
to set the temperature ramp during the link setup sequence, i.e. before
we even probe the ub953 driver.
Add support to the deserializer driver to configure ub953's temperature
ramp.
[1]: Section 7.3.1.1 - https://www.ti.com/lit/gpn/ds90ub953-q1
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
For DS90UB9702-Q1, it is recommended to configure some serializer
settings over the back-channel before the forward-channel is active.
This can only be done if the serializer's I2C address on the FPD-Link
bus is populated in the device tree node.
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The serializer's I2C address on the FPD-Link bus is usually communicated
to the deserializer once the forward-channel is established. But in some
cases it might be necessary to program the serializer (over the
back-channel) before the forward-channel is established.
This can be used e.g. to correct serializer configuration which
otherwise would prevent the FC to be enabled. To be able to communicate
to the serializer before the forward-channel is up, the deserializer
driver neds to know the default i2c address of the serializer.
Allow setting the serializer i2c address using the 'reg' property. This
is optional, and usually not needed.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
We have some code in probe() which is related to RX port initialization,
and should be in ub960_init_rx_ports(). Move the code there.
We also move ub960_reset() so that it is accessible from
ub960_init_rx_ports().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The driver does a lot of iteration over the RX ports with for loops. In
most cases the driver will skip unused RX ports. Also, in the future
patches the FPD-Link IV support will be refreshed with TI's latest init
sequences which involves a lot of additional iterations over the RX
ports, often only for FPD-Link IV ports.
To make the iteration simpler and to make it clearer what we're
iterating over (all or only-active, all or only-fpd4), add macros and
support functions for iterating the RX ports. Use the macros in the
driver, replacing the for loops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The driver supports both UB960 and UB9702. While devices work in similar
ways and have a lot of identical registers, there are also plenty of
differences.
To clarify the situation a bit, move the UB9702 registers to a separate
section and prefix them with UB9702.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The driver is missing checks for i2c read/write errors in many places.
Now that we have added the err parameter to the read/write functions in
the previous patch, add error handling to all the missing places.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
To make future error handling in the drivers easier, add "int *err"
parameter to all the i2c register access functions. It functions the
same was as with e.g. CCI reg write/read helpers.
This was accomplished with the following semantic patch:
@@
identifier FUNC =~ "^ub9.._(rxport_|txport_|ind_)?(read|write|update_bits)(16|_ind)?$";
@@
FUNC(...
+ , int *err
) {
...
int ret;
+
+ if (err && *err)
+ return *err;
...
+ if (ret && err)
+ *err = ret;
+
return ret;
}
@@
identifier FUNC =~ "^ub9.._(rxport_|txport_|ind_)?(read|write|update_bits)(16|_ind)?$";
@@
FUNC(...
+ , NULL
)
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
