AT91 DT #2 for 5.16:
- Add DT nodes for TCB and RTC blocks on SAMA7G5
- Add TCB0 for clocksource and clockevent functionality fallback only in
case PIT64B will fail to probe and as a testbed for this feature on
the Evaluation Kit.
* tag 'at91-dt-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama7g5-ek: use blocks 0 and 1 of TCB0 as cs and ce
ARM: dts: at91: sama7g5: add tcb nodes
ARM: dts: at91: sama7g5: add rtc node
Link: https://lore.kernel.org/r/20211025163428.26285-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rainier was missed when enabling all of the other machines in
commit 239566b032 ("ARM: dts: aspeed: Set earlycon boot argument").
Signed-off-by: Joel Stanley <joel@jms.id.au>
These were meant to be part of commit 4fb27b3f91 ("ARM: dts: aspeed:
rainier: Add system LEDs") but went missing.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The state of this GPIO determines whether a factory reset has been
requested. If a physical switch is used, it can be high or low. During boot,
the software checks and records the state of this switch. If it is different
than the previous recorded state, then the read-write portions of memory are
reformatted.
Signed-off-by: Isaac Kurth <isaac.kurth@ibm.com>
Reviewed-by: Adriana Kobylak <anoo@us.ibm.com>
Link: https://lore.kernel.org/r/20210714214741.1547052-1-blisaac91@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The MCTP LPC driver was loaded by hacking up the compatible in the
devicetree node for KCS 4. With the introduction of the raw KCS driver
this hack is no-longer required. Use the regular compatible string for
KCS 4 and configure the appropriate SerIRQ.
The reset state of the status bits on KCS 4 is inappropriate for the
MCTP LPC binding. Switch to KCS 3 which has a different reset behaviour.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set I2C bus 14 to multi-master mode and add the panel device that will
register the I2C controller as a slave device.
In addition, in early Everest systems, the panel device was behind an
I2C switch, which doesn't work for slave mode. Get it working (albeit
unreliably, since a master transaction might switch the switch at any
moment) by defaulting the switch channel to the one with the panel.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Changes for omap gpmc bindings and devicetree files for v5.16
A series of changes to update the gpmc related bindings to yaml
format, and a few non-urgent dts fixes.
* tag 'omap-for-v5.16/gpmc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap: fix gpmc,mux-add-data type
ARM: dts: omap: Fix boolean properties gpmc,cycle2cycle-{same|diff}csen
dt-bindings: memory-controllers: ti,gpmc: Convert to yaml
dt-bindings: mtd: ti,gpmc-onenand: Convert to yaml
dt-bindings: mtd: ti,gpmc-nand: Convert to yaml
dt-bindings: memory-controllers: Introduce ti,gpmc-child
dt-bindings: net: Remove gpmc-eth.txt
dt-bindings: mtd: Remove gpmc-nor.txt
Link: https://lore.kernel.org/r/pull-1634280279-284035@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is already in v5.15-rc5, but I'm adding it here as well to get
a clean build of the dts files.
* tag 'arm-soc/for-5.15/devicetree':
ARM: dts: bcm2711-rpi-4-b: Fix usb's unit address
ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formatting
ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states
ARM: dts: bcm2711: fix MDIO #address- and #size-cells
ARM: dts: bcm283x: Fix VEC address for BCM2711
Adapt gpio subnode names to match the yaml binding and removal
of the actually non-matching fallback-string for usb-phys
on rk3066/rk3188 (most-specific compatible is and must always
be used).
* tag 'v5.16-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove usb-phy fallback string from rk3066a/rk3188
ARM: dts: rockchip: change gpio nodenames
Link: https://lore.kernel.org/r/3630369.N7QejLDta5@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
IXP4xx DTS changes for the v5.16 kernel:
- Add the PTP timesource
- Push down PCI interrupt properties to the individual
board files.
* tag 'ixp4xx-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ixp4xx: Group PCI interrupt properties together
ARM: dts: Add PTP timesource to the IXP456x
Link: https://lore.kernel.org/r/CACRpkdbSJ662h_B9mAGdXWBeq8ZwKTQvSJ7cZ2x2d8UgELP5QA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX arm64 device tree changes for 5.16:
- New board support: LX2160A based BlueBox3, S32G2 EVB and RDB2 boards.
- Quite some updates on imx8mq-librem5 board: delay the startup of the
SDIO, add power sequencing for M.2 cards, add wifi regulator, add
panel reset GPIO, fix led_r and led_g pinctrl, etc.
- Fix the SPI chipselect polarity for a couple of i.MX8MM boards.
- Add GPU nodes for i.MX8MM 2D and 3D core.
- Add VPU and DISP blk-ctrl devices for i.MX8MM.
- A series from Michael Walle to LS1028A device trees and add GPU
support.
- Random and small updates on various boards.
* tag 'imx-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (37 commits)
arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card
arm64: dts: imx8mm-venice-gw7901.dts: disable pgc_gpumix
arm64: dts: imx8mq-librem5: set debounce interval of volume buttons to 50ms
arm64: dts: imx8mq-librem5: Limit the max sdio frequency
arm64: dts: imx8mq-librem5: add power sequencing for M.2 cards
arm64: dts: imx8mq-librem5: delay the startup of the SDIO
arm64: dts: imx8mq-librem5: wire up the wifi regulator
arm64: dts: imx8mq-librem5: Fix led_r and led_g pinctrl assignments
arm64: dts: imx8mq-librem5: add reset gpio to mantix panel description
arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY
arm64: dts: imx8mm: add DISP blk-ctrl
arm64: dts: imx8mm: add VPU blk-ctrl
arm64: dts: imx8mm: Add GPU nodes for 2D and 3D core
arm64: dts: imx8mm: put USB controllers into power-domains
arm64: dts: imx8mm: add GPC node
arm64: dts: ls1028a: mark internal links between Felix and ENETC as capable of flow control
arm64: dts: freescale: Fix 'interrupt-map' parent address cells
arm64: dts: ls1028a: use phy-mode instead of phy-connection-type
arm64: dts: ls1028a: move PHY nodes to MDIO controller
arm64: dts: ls1028a: disable usb controller by default
...
Link: https://lore.kernel.org/r/20211016140138.1603-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree changes for 5.16:
- New board support: Kobo Libra H2O, Tolino Vision 5, SKOV LT2 and
Colibri i.MX6ULL eMMC variants.
- A series from Fabio Estevam to correct SPI chipselect polarity for
various i.MX6/7 boards.
- A couple of patches from Krzysztof Kozlowski to clean up unsupported
properties from imx6dl-b1x5v2 and imx6dl-prtrvt boards.
- A series from Li Yang to clean up LS1021a based boards and add missing
device nodes.
- A series from Matthias Schiffer to fix typo, add SPI-NOR flash and
partition layout for imx7-tqma7/mba7 boards.
- Fix the schema check errors in i.MX PCIe device nodes.
- Other random and small fix-up and device additions.
* tag 'imx-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (42 commits)
ARM: dts: ls1021a-tsn: use generic "jedec,spi-nor" compatible for flash
ARM: dts: ls1021a: move thermal-zones node out of soc/
ARM: dts: ls1021a-tsn: remove undocumented property "position" from mma8452 node
ARM: dts: ls1021a-qds: change fpga to simple-mfd device
ARM: dts: ls1021a: add #power-domain-cells for power-controller node
ARM: dts: ls1021a: add #dma-cells to qdma node
ARM: dts: ls1021a: fix memory node for schema check
ARM: dts: ls1021a: remove regulators simple-bus
ARM: dts: ls1021a: disable ifc node by default
ARM: dts: ls1021a: breakup long values in thermal node
ARM: dts: ls1021a: fix board compatible to follow binding schema
ARM: dts: ls1021a: update pcie nodes for dt-schema check
ARM: dts: ls1021a-qds: Add node for QSPI flash
ARM: dts: ls1021a: change to use SPDX identifiers
ARM: dts: ls1021a: change dma channels order to match schema
ARM: dts: ls1021a: remove clock-names property for i2c nodes
ARM: dts: imx6dl-prtrvt: drop undocumented TRF7970A NFC properties
ARM: dts: imx6: phytec: Add gpio pinctrl for i2c bus recovery
ARM: dts: imx6: skov: provide panel support for lt2 variants
ARM: dts: imx6qdl-apalis: Fix typo in ADC comment
...
Link: https://lore.kernel.org/r/20211016140138.1603-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt64 for 5.16 (part 1)
Add support for Globalscale MOCHAbin an Armada 7040 based development
board.
* tag 'mvebu-dt64-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: add Globalscale MOCHAbin
Link: https://lore.kernel.org/r/877deemefy.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the conversion of rockchip-usb-phy.yaml a long time used fallback
string for rk3066a/rk3188 was added. The linux driver doesn't do much with
the GRF phy address range, however the u-boot driver rockchip_usb2_phy.c
does. The bits in GRF_UOC0_CON2 for rk3066a/rk3188 and rk3288 for example
don't match. Remove the usb-phy fallback string for rk3066a/rk3188
to prevent possible strange side effects.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828111218.10026-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Move the PCI 'interrupt-map-mask' and '#interrupt-cells' properties
alongside the 'interrupt-map' property in each board dts. This avoids
having incomplete set of interrupt properties which may fail validation.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
STM32 DT for v5.16, round 1
Highlights:
----------
- MPU:
- ST boards:
- Add new stm32mp135f-dk board. It embedds new STM32MP135 SoC,
with 512 MB of DDR3. Several connections are available on this
board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI,
Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in
this tag.
- Change IRQ level for STUSB1600 on DKx boards.
- Fix SAI subclocks range.
- Add ck_usb0_48m clock in USB OHCI node device to match with
STM32MP15 datasheet.
- DH boards:
- Reduce DHCOR SPI NOR frequency to 50 MHz to avoid sporadic issues.
- Fix SAI pin muxing.
- Odyssey:
- Set DCMI pins.
* tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
ARM: dts: stm32: fix SAI sub nodes register range
ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey
ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
ARM: dts: stm32: add initial support of stm32mp135f-dk board
dt-bindings: stm32: document stm32mp135f-dk board
ARM: dts: stm32: add STM32MP13 SoCs support
Link: https://lore.kernel.org/r/9d52c3e2-a3b9-89f3-1896-7cd3560e7010@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas ARM DT updates for v5.16 (take two)
- SPI Multi I/O Bus, SDHI, and Ethernet support for the RZ/G2L SoC,
- SPI Multi I/O Bus, camera, and video-on support for the R-Car V3U
SoC,
- SPI FLASH support for the Falcon development board,
- eMMC, microSD, and Ethernet support for the RZ/G2L SMARC EVK
development board,
- 2 GHz High-Performance support for the R-Car H3e-2G, M3e-2G, and
M3Ne-2G SoCs,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
mailmap: Fix text encoding for Niklas Söderlund
arm64: dts: renesas: rcar-gen3e: Add Cortex-A57 2 GHz opps
arm64: dts: renesas: rzg2l-smarc-som: Enable Ethernet
arm64: dts: renesas: r9a07g044: Add GbEthernet nodes
arm64: dts: renesas: Add ports node to all adv7482 nodes
arm64: dts: renesas: r8a779a0: Add and connect all CSI-2, ISP and VIN nodes
arm64: dts: renesas: rzg2l-smarc: Enable microSD on SMARC platform
arm64: dts: renesas: rzg2l-smarc-som: Enable eMMC on SMARC platform
arm64: dts: renesas: r9a07g044: Add SDHI nodes
arm64: dts: renesas: falcon-cpu: Add SPI flash via RPC
arm64: dts: renesas: r8a779a0: Add RPC node
arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node
Link: https://lore.kernel.org/r/cover.1634298094.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ASPEED device tree updates for 5.15
- New machines:
* TYAN S7106 BMC, a x86 server from about four years ago
- Descriptions for the AST2600 ADC, which now has an upstream driver
- Lots of GPIO line names. The OpenBMC project has adopted a scheme for
naming the lines, and new additions will follow this guide
- New I2C devices for Rainier, Everest, EthanolX, Mt Jade
- Fixes for fp5280g2 which has seen some recent development, including
the addtion of a QEmu machine for testing
* tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: fp5280g2: Use the 64M layout
ARM: dts: aspeed: Add TYAN S7106 BMC machine
ARM: dts: aspeed: rainier: Add power-config-full-load gpio
ARM: dts: aspeed: p10bmc: Define secure boot gpio
ARM: dts: aspeed: mtjade: Add some gpios
ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
ARM: dts: everest: Define name for gpio line B6
ARM: dts: everest: Define name for gpio line Q2
ARM: dts: rainier: Define name for gpio line Q2
ARM: dts: everest: Add 'factory-reset-toggle' as GPIOF6
ARM: dts: aspeed: everest: Add I2C bus 15 muxes
ARM: dts: aspeed: rainier: Add system LEDs
ARM: dts: aspeed: amd-ethanolx: Add FRU EEPROM
ARM: dts: fp5280g2: Enable KCS 3 for MCTP binding
Link: https://lore.kernel.org/r/CACPK8XdrMzY9tzdof7KpzxKquTo7GcWW4N9Zqwtmmu73C7htXA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
