The Quartz64 Model B has a Winbound 25Q64DWZPIG SPI flash chip,
identified as 'U13' on the component placement schematic.
In the Quartz 64 Model-B Schematic from 20220124 on page 17, we can see
that the VCC connector is connected to VCCIO_FLASH and page 4 shows that
that in turn is connected to the VCCIO2 domain.
That domain uses vcc_1v8 as its power source.
This fixes the following warning:
spi-nor spi4.0: supply vcc not found, using dummy regulator
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250503152917.138648-3-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to paragraph "7.16. Power" of the RTL8211F-CG datasheet, gmac0
needs to have a 3.3V power supply.
On page 22 of the NanoPi R5S version 2204, that is identified as
VCC_GEPHY_3V3 which is connected to the VCC_3V3 power source.
This fixes the following warning:
rk_gmac-dwmac fe2a0000.ethernet: supply phy not found, using dummy regulator
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250503152917.138648-2-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The USB-C port on the NanoPC-T6 was not providing VBUS (vbus5v0_typec
regulator disabled, gpio-58 out lo) due to misconfiguration. The
original setup with regulator-always-on and regulator-boot-on forced
the port on, masking the issue, but removing these properties revealed
that the fusb302 driver was not enabling the regulator dynamically.
Changes:
- Removed regulator-always-on and regulator-boot-on from vbus5v0_typec
and vbus5v0_usb to allow driver control.
- Changed power-role from "source" to "dual" in the usb-c-connector to
support OTG functionality.
- Added pd-revision = /bits/ 8 <0x2 0x0 0x1 0x2> to the FUSB302MPX
node to specify USB Power Delivery (PD) Revision 2.0, Version 1.2,
ensuring the driver correctly advertises PD capabilities and
negotiates power roles (source/sink).
- Added op-sink-microwatt and sink-pdos for proper sink mode
configuration (1W min, 15W max).
- Added typec-power-opmode = "1.5A" to enable 1.5A fallback for non-PD
USB-C devices, aligning with the 5V/2A hardware limit.
- Set try-power-role to "source" to prioritize VBUS enablement.
- Adjusted usb_host0_xhci dr_mode from "host" to "otg" and added
usb-role-switch for dual-role support.
Testing:
- Verified VBUS (5V) delivery to a sink device (USB thumb drive).
- Confirmed USB host mode with lsusb detecting connected devices.
- Validated USB device mode with adb devices when connected to a PC.
- Tested dual-role (OTG) functionality with try-power-role set to
"source" and "sink"; "source" prioritizes faster VBUS activation.
- Validated functionality with a mobile device, including USB Power
Delivery, file transfer, USB tethering, MIDI, and image transfer.
- Tested USB-C Ethernet adapter compatibility in host mode.
- Tested USB-C hub compatibility in host mode.
Signed-off-by: John Clark <inindev@gmail.com>
Link: https://lore.kernel.org/r/20250422210345.196050-1-inindev@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Orange Pi 5 Max and Ultra has onboard AP6611s with Bluetooth 5.3
connected via UART7.
The chip reports as:
[ 3.747864] Bluetooth: hci0: BCM: chip id 3
[ 3.750021] Bluetooth: hci0: BCM: features 0x0f
[ 3.775923] Bluetooth: hci0: SYN43711A0
[ 3.775930] Bluetooth: hci0: BCM (001.001.030) build 0000
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Link: https://lore.kernel.org/r/20250427182019.1862-1-honyuenkwun@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa Rock 5B component placement document identifies the SPI Nor
Flash chip as 'U4300' which is described on page 25 of the Schematic
v1.45. There we can see that the VCC connector is connected to the
VCC_3V3_S3 power source.
This fixes the following warning:
spi-nor spi5.0: supply vcc not found, using dummy regulator
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250425092601.56549-5-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As described on page 37 of PineTab2 Schematic-20230417, the SPI Flash's
VCC connector is connected to VCCIO_FLASH and according to page 6 of
that same schematic, that belongs to the VCC_1V8 power source.
This fixes the following warning:
spi-nor spi4.0: supply vcc not found, using dummy regulator
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250425092601.56549-4-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/) for the Haikou
devkit with Tiger RK3588 SoM.
The Video Demo adapter is an adapter connected to the fake PCIe slot
labeled "Video Connector" on the Haikou devkit.
It's main feature is a Leadtek DSI-display with touchscreen and a camera
(that is not supported yet). To drive these components a number of
additional regulators are grouped on the adapter as well as a PCA9670
gpio-expander to provide the needed additional gpio-lines.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org> # Makefile
Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250226140942.3825223-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the necessary DT changes to enable eDP0 on RK3588S EVB1 board:
- Set pinctrl of pwm12 for backlight
- Enable edp0/hdptxphy0/vp2
- Assign the parent of DCLK_VOP2_SRC to PLL_V0PLL
- Add aux-bus/panel nodes
For RK3588, the PLL_V0PLL is specifically designed for the VOP2. This
means the clock rate of PLL_V0PLL can be adjusted according to the dclk
rate of relevant VP. It is typically assigned as the dclk source of a
specific VP when the clock of relevant display mode is unusual, such as
the eDP panel 'lg,lp079qx1-sp0v' paired with RK3588S EVB1, which has a
clock rate of 202.02MHz.
Additionally, the 'force-hpd' is set for edp0 because the HPD pin on the
panel side is not connected to the eDP HPD pin on the SoC side according
to the RK3588S EVB1 hardware design.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-14-damon.ding@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the binding header now providing the SCMI_SRST_H_TRNG_NS constant,
switch back to it from the temporary numeric value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull soundwire fix from Vinod Koul:
- add missing config symbol CONFIG_SND_HDA_EXT_CORE required for asoc
driver CONFIG_SND_SOF_SOF_HDA_SDW_BPT
* tag 'soundwire-6.15-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
ASoC: SOF: Intel: Let SND_SOF_SOF_HDA_SDW_BPT select SND_HDA_EXT_CORE
