Refactor the ad7606 drivers to dynamically allocate the channel info.
The channel info was getting a bit unwieldy. In some cases, the
indio_dev->channels field was getting assigned up to 3 different times,
each in a different function, making it difficult to see where the info
was coming from. This problem stems from the number of permutations of
the channel array needed to support various modes of operation and data
buses. We already have 4 per chip (hardware mode, software mode, AXI ADC
backend and AXI ADC backend with software mode) and we intend to add two
more per chip when adding SPI offload support.
To make it easier to read and maintain, move all of the channel setup
to a single function that dynamically allocates and fills in the channel
info.
Additionally, this lets us remove some hacks where we had to compute an
offset due to the fact that sometimes there was a soft timestamp channel
at the start of the array. Now the timestamp channel is always at the
end of the array as is typical in other drivers.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-9-4b605427774c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79124 is a 12-bit, 8-channel, SAR ADC. The ADC supports
an automatic measurement mode, with an alarm interrupt for out-of-window
measurements. The window is configurable for each channel.
The I2C protocol for manual start of the measurement and data reading is
somewhat peculiar. It requires the master to do clock stretching after
sending the I2C slave-address until the slave has captured the data.
Needless to say this is not well suopported by the I2C controllers.
Thus do not support the BD79124's manual measurement mode but implement
the measurements using automatic measurement mode, relying on the
BD79124's ability of storing latest measurements into register.
Support also configuring the threshold events for detecting the
out-of-window events.
The BD79124 keeps asserting IRQ for as long as the measured voltage is
out of the configured window. Thus, prevent the user-space from choking
on the events and mask the received event for a fixed duration (1 second)
when an event is handled.
The ADC input pins can be also configured as general purpose outputs.
Make those pins which don't have corresponding ADC channel node in the
device-tree controllable as GPO.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/ca3886c9abcb268ca976e62cd7da28bf5d6e6382.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The new devm_iio_adc_device_alloc_chaninfo_se() -helper is intended to
help drivers avoid open-coding the for_each_node -loop for getting the
channel IDs. The helper provides standard way to detect the ADC channel
nodes (by the node name), and a standard way to convert the "reg"
-properties to channel identification numbers, used in the struct
iio_chan_spec. Furthermore, the helper can optionally check the found
channel IDs are smaller than given maximum. This is useful for callers
which later use the IDs for example for indexing a channel data array.
The original driver treated all found child nodes as channel nodes. The
new helper requires channel nodes to be named channel[@N]. This should
help avoid problems with devices which may contain also other but ADC
child nodes. Quick grep from arch/* with the sun20i-gpadc's compatible
string didn't reveal any in-tree .dts with channel nodes named
otherwise. Also, same grep shows all the in-tree .dts seem to have
channel IDs between 0..num of channels.
Use the new helper.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/e367a803c0d625e60c9fca16c55a25eee06b5a89.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The new devm_iio_adc_device_alloc_chaninfo_se() -helper is intended to
help drivers avoid open-coding the for_each_node -loop for getting the
channel IDs. The helper provides standard way to detect the ADC channel
nodes (by the node name), and a standard way to convert the "reg"
-properties to channel identification numbers, used in the struct
iio_chan_spec. Furthermore, the helper can optionally check the found
channel IDs are smaller than given maximum. This is useful for callers
which later use the IDs for example for indexing a channel data array.
The original driver treated all found child nodes as channel nodes. The
new helper requires channel nodes to be named channel[@N]. This should
help avoid problems with devices which may contain also other but ADC
child nodes. Quick grep from arch/* with the rzg2l_adc's compatible
string didn't reveal any in-tree .dts with channel nodes named
otherwise. Also, same grep shows all the .dts seem to have channel IDs
between 0..num of channels.
Use the new helper.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/e84ccff01070eaee3dd1ae2d7e109f963168f586.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are a few use-cases where child nodes with a specific name need to
be parsed. Code like:
fwnode_for_each_child_node()
if (fwnode_name_eq())
...
can be found from a various drivers/subsystems. Adding a macro for this
can simplify things a bit.
In a few cases the data from the found nodes is later added to an array,
which is allocated based on the number of found nodes. One example of
such use is the IIO subsystem's ADC channel nodes, where the relevant
nodes are named as channel[@N].
Add helpers for iterating and counting device's sub-nodes with certain
name instead of open-coding this in every user.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/2767173b7b18e974c0bac244688214bd3863ff06.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows writing u64 values to the ADMV8818's high and low-pass
filter frequencies. It includes the following changes:
- Rejects negative frequencies in admv8818_write_raw.
- Adds a write_raw_get_fmt function to admv8818's iio_info, returning
IIO_VAL_INT_64 for the high and low-pass filter 3dB frequency channels.
Fixes: f34fe888ad ("iio:filter:admv8818: add support for ADMV8818")
Signed-off-by: Brian Pellegrino <bpellegrino@arka.org>
Signed-off-by: Sam Winchenbach <swinchenbach@arka.org>
Link: https://patch.msgid.link/20250328174831.227202-7-sam.winchenbach@framepointer.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SARADC IP on the GXLX SoC itself is identical to the one found on
GXL SoCs. However, GXLX SoCs require poking the first three bits in the
MESON_SAR_ADC_REG12 register to get the three MPLL clocks (used as clock
generators for the audio frequencies) to work.
The reason why there are MPLL clock bits in the ADC register space is
entirely unknown and it seems that nobody is able to comment on this.
So clearly mark this as a workaround and add a warning so users are
notified that this workaround can change (once we know what these bits
actually do).
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patch.msgid.link/20250330101922.1942169-3-martin.blumenstingl@googlemail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some BH1750 sensors require a hardware reset before they can be
detected on the I2C bus. This implementation adds support for an
optional reset GPIO that can be specified in the device tree.
The reset sequence pulls the GPIO low and then high before initializing
the sensor, which enables proper detection with tools like i2cdetect.
This is particularly important for sensors that power on in an
undefined state.
Signed-off-by: Sergio Perez <sergio@pereznus.es>
Link: https://patch.msgid.link/20250324135920.6802-2-sergio@pereznus.es
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On Intel platforms, the HID_USAGE_SENSOR_HUMAN_PROXIMITY report size is 16
bits. This patch adds support for handling 16-bit report sizes for the
HID_USAGE_SENSOR_HUMAN_PROXIMITY usage in the HID sensor proximity driver.
Previously, the driver only supported 8-bit and 32-bit report sizes. With
this change, the driver can now correctly process 16-bit proximity data,
ensuring accurate human presence detection on platforms where this report
size is used.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20250317013634.4117399-1-lixu.zhang@intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use regmap cache to replace the maintenance of the interrupt mapping
state by a member variable intio. The interrupt mapping is initialized
when the driver is probed, and it is perfectly cacheable.
The patch will still leave the function set_interrupts(). A follow up
patch takes care of it, when cleaning up the INT enable register
variable.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250313165049.48305-2-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move getting the scan_type to ad4030_conversion(). Previously, we were
getting the scan_type in two other places, then storing it in the
state struct before using it in ad4030_conversion(). This was a bit
fragile against potential future changes since it isn't obvious that
anything that could potentially change the scan_type would need to
also update the state struct. Also, the non-obviousness of this led to
a redundant call to iio_get_current_scan_type() in
ad4030_single_conversion() since it also calls ad4030_set_mode() which
in turn calls ad4030_conversion().
To simplify things, just call iio_get_current_scan_type() in
ad4030_conversion() where the returned struct is actually used and
don't bother storing it in the state struct.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250310-iio-adc-ad4030-check-scan-type-err-v1-4-589e4ebd9711@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
