The kernel test robot reports the following warning.
drivers/spi/spi-cadence-quadspi.c:966:24: warning: comparison of distinct pointer types ('typeof (len) *' (aka 'unsigned int *') and 'typeof (500UL) *' (aka 'unsigned long *')) [-Wcompare-distinct-pointer-types]
msecs_to_jiffies(max(len, 500UL)))) {
^~~~~~~~~~~~~~~
include/linux/minmax.h:58:19: note: expanded from macro 'max'
#define max(x, y) __careful_cmp(x, y, >)
^~~~~~~~~~~~~~~~~~~~~~
include/linux/minmax.h:42:24: note: expanded from macro '__careful_cmp'
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~~~~~~~
include/linux/minmax.h:32:4: note: expanded from macro '__safe_cmp'
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~~~~~~~
include/linux/minmax.h:18:28: note: expanded from macro '__typecheck'
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
1 warning generated.
This happens because size_t is unsigned long on 64-bit platforms like
arm64 but it is unsigned int on 32-bit platforms like arm. Omitting the
"UL" would result in a warning on 64-bit platforms. Squash it by type
casting the arguments to size_t using max_t(). This way builds on both
type of platforms can be satisfied. There is no chance of any truncation
since 500 is small enough to fit into both int and long.
Fixes: f453f29397 ("spi: cadence-quadspi: Wait at least 500 ms for direct reads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210108181457.30291-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a new warning report by build for make ARCH=MIPS allmodconfig:
drivers/spi/spi-cadence-quadspi.c: In function 'cqspi_direct_read_execute':
./include/linux/minmax.h:18:28: warning: comparison of distinct pointer types lacks a cast
18 | (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
| ^~
./include/linux/minmax.h:32:4: note: in expansion of macro '__typecheck'
32 | (__typecheck(x, y) && __no_side_effects(x, y))
| ^~~~~~~~~~~
./include/linux/minmax.h:42:24: note: in expansion of macro '__safe_cmp'
42 | __builtin_choose_expr(__safe_cmp(x, y), \
| ^~~~~~~~~~
./include/linux/minmax.h:58:19: note: in expansion of macro '__careful_cmp'
58 | #define max(x, y) __careful_cmp(x, y, >)
| ^~~~~~~~~~~~~
drivers/spi/spi-cadence-quadspi.c:1153:24: note: in expansion of macro 'max'
1153 | msecs_to_jiffies(max(len, 500UL)))) {
| ^~~
"len" is unsigned,however,"500" is unsigned long.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20210107115704.3835282-1-siyanteng@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
This series adds Tegra210, Tegra186, and Tegra194 Quad SPI driver and
enables Quad SPI on Jetson Nano and Jetson Xavier NX.
QSPI controller is available on Tegra210, Tegra186 and Tegra194.
Tegra186 and Tegra194 has additional feature of combined sequence mode
where command, address and data can all be transferred in a single transfer.
Combined sequence mode is useful only when using DMA mode transfer.
This series does not have combined sequence mode feature as Tegra186/Tegra194
GPCDMA driver is not upstreamed yet.
This series includes
- dt-binding document
- QSPI driver for Tegra210/Tegra186/Tegra194
- Enables QSPI on Jetson Nano and Jetson Xavier NX.
Delta between patch versions:
[v5]: Simplified implementation in Patch-0006
[v4]: Updated dummy cycles implementation based on v3 feedback
- Added dummy_data bit field int spi_transfer to indicate corresponding
transfer is dummy bytes transfer.
- Updated Tegra QSPI transfer_one_message to identify dummy transfer and
to use HW supported dummy bytes transfer when dummy cycles are with in
Tegra QSPI supported max HW dummy cycles otherwise fallsback to transfer
dummy bytes from software.
- Updated dt-bindings based on v3 feedback.
[v3]: v2 has some mixed patches sent out accidentally.
v3 sends proper patches with fixes mentioned in v2.
[v2]: below v1 feedback
- Added SPI_MASTER_USES_HW_DUMMY_CYCLES flag for controllers supporting
hardware dummy cycles and skips dummy bytes transfer from software for
these controllers.
- Updated dt-binding doc with tx/rx tap delay properties.
- Added qspi_out clock to dt-binding doc which will be used later with
ddr mode support.
- All other v1 feedback on some cleanup.
Sowjanya Komatineni (9):
dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM
dt-bindings: spi: Add Tegra Quad SPI device tree binding
MAINTAINERS: Add Tegra Quad SPI driver section
spi: tegra210-quad: Add support for Tegra210 QSPI controller
spi: spi-mem: Mark dummy transfers by setting dummy_data bit
spi: tegra210-quad: Add support for hardware dummy cycles transfer
arm64: tegra: Enable QSPI on Jetson Nano
arm64: tegra: Add QSPI nodes on Tegra194
arm64: tegra: Enable QSPI on Jetson Xavier NX
.../bindings/spi/nvidia,tegra210-quad.yaml | 117 ++
MAINTAINERS | 8 +
.../dts/nvidia/tegra194-p3509-0000+p3668-0000.dts | 12 +
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 28 +
arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts | 12 +
arch/arm64/boot/dts/nvidia/tegra210.dtsi | 5 +-
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-mem.c | 1 +
drivers/spi/spi-tegra210-quad.c | 1410 ++++++++++++++++++++
include/dt-bindings/clock/tegra210-car.h | 2 +-
include/linux/spi/spi.h | 2 +
12 files changed, 1604 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
create mode 100644 drivers/spi/spi-tegra210-quad.c
--
2.7.4
Tegra Quad SPI controller hardware supports sending dummy bytes based
on programmed dummy clock cycles after the actual transfer bytes.
This patch adds this support of hardware dummy bytes transfer and
skips transfer of dummy bytes from the software.
For dummy cycles more than Tegra Quad SPI hardware maximum dummy
cycles limit, driver transfers dummy bytes from the software.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-7-git-send-email-skomatineni@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Double Transfer Rate (DTR) mode transfers data twice per clock cycle.
Add support for parsing DTR ops and set up the registers to allow it.
Most SPI NOR flashes expect 2 byte commands. Parse the 2-byte opcode
from SPI MEM and set it up in the CQSPI_REG_OP_EXT_LOWER register.
Increment the delay needed before issuing indirect writes because larger
delay is needed for DTR mode. With the current delay some writes end up
missing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-8-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing a direct read via DMA the timeout for completion is set
equal to the read length. This is fine for larger reads. For a small
read like the Read Status Register command, the timeout would be 1 or 2
milliseconds. This is not enough to cover the overhead needed in setting
up DMA.
Make sure the timeout is at least 500 ms to allow DMA ample time to
finish. For reads larger than 500 bytes, the timeout will continue to be
equal to the read length.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201222184425.7028-7-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI MEM deals with dummy bytes but the controller deals with dummy
cycles. Multiplying bytes by 8 is correct if the dummy phase uses 1S
mode since 1 byte will be sent in 8 cycles. But if the dummy phase uses
4S mode then 1 byte will be sent in 2 cycles.
To correctly translate dummy bytes to dummy cycles, the dummy buswidth
also needs to be taken into account. Divide 8 by the buswidth to get the
correct multiplier for getting the number of cycles.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-5-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a command does not have an address phase it goes via the STIG path.
The dummy cycles are not initialized for the STIG commands. As a result,
STIG commands with dummy cycles will not work.
Initialize the dummy cycle field before issuing the STIG command to make
sure it is sent correctly. Move the code to calculate dummy cycle value
to a separate function so it is not repeated twice. DTR support will add
some more logic here to it is worth it to extract it out in a function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-4-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit 9326e4f1e5 ("spi: Limit the spi device max speed to
controller's max speed"), the SPI device max speed is set to the
controller's max speed if it is larger. The Cadence QSPI controller does
not set the controller's max speed so it is left at its initial value of
0. This means the SPI device max speed is always set to 0.
The SPI device max speed is used to calculate the baud rate divider when
performing an operation. If this speed is 0, the default divider of 32
is used. No matter what speed is specified by the device tree property
'spi-max-frequency', the device will always operate at ref_clk / 32.
Fix this by setting master->max_speed_hz to the ref clock speed so the
correct divider can be calculated.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of the 'include/uapi/linux/spi/spi.h' header, the
type of the macros are enforced to 'unsigned long int' via the _BITUL()
macro.
This causes some -Wformat warnings in the spi-stm32 driver.
This patch adds a double-negation operator to the bit-masks. Essentially,
the important values for debugging are 0 or 1, while masking them directly
would show 0 or BIT(x) values.
This way, the type of the arguments are automatically re-cast.
Fixes: f7005142da ("spi: uapi: unify SPI modes into a single spi.h header")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210104143103.56510-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change moves all the SPI mode bits into a separate 'spi.h' header in
uAPI. This is meant to re-use these definitions inside the kernel as well
as export them to userspace (via uAPI).
The SPI mode definitions have usually been duplicated between between
'include/linux/spi/spi.h' and 'include/uapi/linux/spi/spidev.h', so
whenever adding a new entry, this would need to be put in both headers.
They've been moved from 'include/linux/spi/spi.h', since that seems a bit
more complete; the bits have descriptions and there is the SPI_MODE_X_MASK.
This change also does a conversion of these bitfields to _BITUL() macro.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI devices, require toggling the CS every transferred byte.
Enable such possibility in the spi-orion driver.
Note that in order to use it, in the driver of a secondary device
attached to this controller, the SPI bus 'mode' field must be
updated with SPI_CS_WORD flag before calling spi_setup() routine.
In addition to that include a work-around - some devices, such as
certain models of SLIC (Subscriber Line Interface Card),
may require extra delay after CS toggling, so add a minimal
timing relaxation in relevant places.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-3-kostap@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-orion driver disables its clocks whenever it is not used.
In usual case during boot (i.e. using SPI flash) it is not a problem,
as the child device driver is present and probed along with
spi_register_master() execution.
However in case the child device driver is not ready
(e.g. when its type is module_spi_driver) the spi_setup() callback
can be called after the spi-orion probe. It may happen,
that as a result there will be an attempt to access controller's
registers with the clocks disabled.
Prevent such situations and make sure the clocks are on,
each time the spi_setup() is called.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-2-kostap@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 36e2c7421f ("fs: don't allow splice read/write without
explicit ops") we've required that file operation structures explicitly
enable splice support, rather than falling back to the default handlers.
Most /proc files use the indirect 'struct proc_ops' to describe their
file operations, and were fixed up to support splice earlier in commits
40be821d627c..b24c30c67863, but the mountinfo files interact with the
VFS directly using their own 'struct file_operations' and got missed as
a result.
This adds the necessary support for splice to work for /proc/*/mountinfo
and friends.
Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull NTB fixes from Jon Mason:
"Bug fix for IDT NTB and Intel NTB LTR management support"
* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
ntb: idt: fix error check in ntb_hw_idt.c
Pull crypto fixes from Herbert Xu:
"Fix a number of autobuild failures due to missing Kconfig
dependencies"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qat - add CRYPTO_AES to Kconfig dependencies
crypto: keembay - Add dependency on HAS_IOMEM
crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY
Pull objtool fix from Ingo Molnar:
"Fix a segfault that occurs when built with Clang"
* tag 'objtool-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix seg fault with Clang non-section symbols
Pull timer fixes from Ingo Molnar:
"Update/fix two CPU sanity checks in the hotplug and the boot code, and
fix a typo in the Kconfig help text.
[ Context: the first two commits are the result of an ongoing
annotation+review work of (intentional) tick_do_timer_cpu() data
races reported by KCSAN, but the annotations aren't fully cooked
yet ]"
* tag 'timers-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix spelling mistake in Kconfig "fullfill" -> "fulfill"
tick/sched: Remove bogus boot "safety" check
tick: Remove pointless cpu valid check in hotplug code
Pull scheduler fix from Ingo Molnar:
"Fix a context switch performance regression"
* tag 'sched-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Optimize finish_lock_switch()
Commit c9a3c4e637 ("mfd: ab8500-debugfs: Remove extraneous curly
brace") removed a left-over curly brace that caused build failures, but
Joe Perches points out that the subsequent 'seq_putc()' should also be
removed, because the commit that caused all these problems already added
the final '\n' to the seq_printf() above it.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 886c812165 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull PCI fixes from Bjorn Helgaas:
- Fix a tegra enumeration regression (Rob Herring)
- Fix a designware-host check that warned on *success*, not failure
(Alexander Lobakin)
* tag 'pci-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dwc: Fix inverted condition of DMA mask setup warning
PCI: tegra: Fix host link initialization
Clang errors:
drivers/mfd/ab8500-debugfs.c:1526:2: error: non-void function does not return a value [-Werror,-Wreturn-type]
}
^
drivers/mfd/ab8500-debugfs.c:1528:2: error: expected identifier or '('
return 0;
^
drivers/mfd/ab8500-debugfs.c:1529:1: error: extraneous closing brace ('}')
}
^
3 errors generated.
The cleanup in ab8500_interrupts_show left a curly brace around, remove
it to fix the error.
Fixes: 886c812165 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.
Fix this by inverting the condition.
[bhelgaas: join string to make it greppable]
Fixes: 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.
This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.
So just initialize 'val' to zero to avoid the issue.
Fixes: 110b055b28 ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Refactor 'perf stat' per CPU/socket/die/thread aggregation fixing use
cases in ARM machines.
- Fix memory leak when synthesizing SDT probes in 'perf probe'.
- Update kernel header copies related to KVM, epol_pwait. msr-index and
powerpc and s390 syscall tables.
* tag 'perf-tools-2020-12-24' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (24 commits)
perf probe: Fix memory leak when synthesizing SDT probes
perf stat aggregation: Add separate thread member
perf stat aggregation: Add separate core member
perf stat aggregation: Add separate die member
perf stat aggregation: Add separate socket member
perf stat aggregation: Add separate node member
perf stat aggregation: Start using cpu_aggr_id in map
perf cpumap: Drop in cpu_aggr_map struct
perf cpumap: Add new map type for aggregation
perf stat: Replace aggregation ID with a struct
perf cpumap: Add new struct for cpu aggregation
perf cpumap: Use existing allocator to avoid using malloc
perf tests: Improve topology test to check all aggregation types
perf tools: Update s390's syscall.tbl copy from the kernel sources
perf tools: Update powerpc's syscall.tbl copy from the kernel sources
perf s390: Move syscall.tbl check into check-headers.sh
perf powerpc: Move syscall.tbl check to check-headers.sh
tools headers UAPI: Synch KVM's svm.h header with the kernel
tools kvm headers: Update KVM headers from the kernel sources
tools headers UAPI: Sync KVM's vmx.h header with the kernel sources
...
Pull coccinelle updates from Julia Lawall.
* 'for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccicheck: Correct usage of make coccicheck
coccinelle: update expiring email addresses
coccinnelle: Remove ptr_ret script
kbuild: do not use scripts/ld-version.sh for checking spatch version
remove boolinit.cocci
Commit 64a1b95bb9 ("genirq: Restrict export of irq_to_desc()") removed
the export of irq_to_desc() unless powerpc KVM is being built, because
there is still a use of irq_to_desc() in modular code there.
However it used:
#ifdef CONFIG_KVM_BOOK3S_64_HV
Which doesn't work when that symbol is =m, leading to a build failure:
ERROR: modpost: "irq_to_desc" [arch/powerpc/kvm/kvm-hv.ko] undefined!
Fix it by checking for the definedness of the correct symbol which is
CONFIG_KVM_BOOK3S_64_HV_MODULE.
Fixes: 64a1b95bb9 ("genirq: Restrict export of irq_to_desc()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull misc vfs updates from Al Viro:
"Assorted patches from previous cycle(s)..."
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix hostfs_open() use of ->f_path.dentry
Make sure that make_create_in_sticky() never sees uninitialized value of dir_mode
fs: Kill DCACHE_DONTCACHE dentry even if DCACHE_REFERENCED is set
fs: Handle I_DONTCACHE in iput_final() instead of generic_drop_inode()
fs/namespace.c: WARN if mnt_count has become negative
Pull documentation fixes from Jonathan Corbet:
"A small set of late-arriving, small documentation fixes"
* tag 'docs-5.11-2' of git://git.lwn.net/linux:
docs: admin-guide: Fix default value of max_map_count in sysctl/vm.rst
Documentation/submitting-patches: Document the SoB chain
Documentation: process: Correct numbering
docs: submitting-patches: Trivial - fix grammatical error
