On ATSM the PL1 limit is disabled at power up. The previous uapi assumed
that the PL1 limit is always enabled and therefore did not have a notion of
a disabled PL1 limit. This results in erroneous PL1 limit values when the
PL1 limit is disabled. For example at power up, the disabled ATSM PL1 limit
was previously shown as 0 which means a low PL1 limit whereas the limit
being disabled actually implies a high effective PL1 limit value.
To get round this problem, the PL1 limit uapi is expanded to include a
special value 0 to designate a disabled PL1 limit. A read value of 0 means
that the PL1 power limit is disabled, writing 0 disables the limit.
The link between this patch and the bugs mentioned below is as follows:
* Because on ATSM the PL1 power limit is disabled on power up and there
were no means to enable it, we previously implemented the means to
enable the limit when the PL1 hwmon entry (power1_max) was written to.
* Now there is a IGT igt@i915_hwmon@hwmon_write which (a) reads orig value
from all hwmon sysfs (b) does a bunch of random writes and finally (c)
restores the orig value read. On ATSM since the orig value is 0, when
the IGT restores the 0 value, the PL1 limit is now enabled with a value
of 0.
* PL1 limit of 0 implies a low PL1 limit which causes GPU freq to fall to
100 MHz. This causes GuC FW load and several IGT's to start timing out
and gives rise to these Intel CI bugs. After this patch, writing 0 would
disable the PL1 limit instead of enabling it, avoiding the freq drop
issue.
v2: Add explanation for bugs mentioned below (Rodrigo)
v3: Eliminate race during PL1 disable and verify (Tvrtko)
Change return to -ENODEV if verify fails (Tvrtko)
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/8062
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/8060
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230401024146.1826092-1-ashutosh.dixit@intel.com
The encoder update_prepare()/complete() hooks were added to hold a
TC port link reference for all outputs in the atomic state around the
whole modeset enable sequence - thus locking the ports' TC mode - and
set the TBT/DP-alt PLL type corresponding to the current TC mode.
Since nothing depends on the PLL selection before/after then encoder's
pre_pll_enable/post_pll_disable hooks are called, the above steps can be
moved to these hooks, so do that and remove the
update_prepare()/complete() hooks.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-30-imre.deak@intel.com
Enable the power required for the HPD live status register access
instead of depending on the caller blocking the TC-cold power state
(during HW readout and connector probing).
A follow up patch will remove connecting/disconnecting the PHY around
connector probing, so querying the HPD status can happen in this case
without TC-cold being blocked.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-24-imre.deak@intel.com
Simplify tc_cold_block()/unblock() by dropping their power domain
parameter. The power domain depends on the current TC mode, which -
after the previous patch - can't change while the PHY is connected,
holding a TC-cold-off power domain reference. Based on this the domain
can be deducted from the current TC mode instead of having to pass this
as a parameter.
Blocking TC-cold for the PHY HW readout happens before the current TC
mode is determined, so here the initial power domain must be still
manually passed.
For debugging still keep track of the domain used for tc_cold_block()
and verify that it remained the same until tc_cold_unblock().
While at it rename tc_cold_get_power_domain() to
tc_phy_cold_off_domain(), reflecting the name of platform specific hook
added in the next patch.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-19-imre.deak@intel.com
A follow-up patch simplifies the tc_cold_block()/unblock() functions,
dropping the power domain parameter. For this it must be ensured that
the power domain - which depends on the actual TC mode and so the VBT
legacy port flag - can't change while the PHY is in a connected state
and accordingly TC-cold is blocked. Make this so, by fixing up the VBT
legacy flag only in the disconnected TC mode, instead of whenever the
HPD state is retrieved.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-15-imre.deak@intel.com
Add generic handlers to connect/disconnect a PHY.
Setting the TC mode to the target mode deducted from the HPD state and -
if connecting to this mode fails - falling back to connecting to the
default (TBT) mode are common to all platforms; move the logic for this
from the ICL specific connect / disconnect handlers to the generic ones.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-12-imre.deak@intel.com
Move the TC port specific fields from intel_digital_port to a new
intel_tc_port struct. Pass an intel_tc_port pointer to all static
functions in intel_tc.c keeping dig_port accessible for these via a
pointer stored in the new struct.
The next patch will allocate the intel_tc_port dynamically, allowing
moving the struct definition to intel_tc.c.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-6-imre.deak@intel.com
DSC_Output_Format_Sink_Support entry is added to i915_dsc_fec_support_show
to depict if sink supports DSC output formats (RGB/YCbCr420/YCbCr444).
Also, new debugfs entry is created to enforce output format. This is
required because of our driver policy. For ex. if a mode is supported
in both RGB and YCbCr420 output formats by the sink, our policy is to
try RGB first and fall back to YCbCr420, if mode cannot be shown
using RGB. So, to test other output formats like YCbCr420 or YCbCr444,
we need a debugfs entry (force_dsc_output_format) to force this
output format.
v2: -Func name changed to intel_output_format_name() (Jani N)
-Return forced o/p format from intel_dp_output_format() (Jani N)
v3: -output_format_str[] to remain static (Jani N)
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-8-suraj.kandpal@intel.com
Now that we have laid the groundwork for YUV420 Enablement
we fill up native_420 field in vdsc_cfg and add appropriate
checks wherever required.
---v2
-adding native_422 field as 0 [Vandita]
-filling in second_line_bpg_offset, second_line_offset_adj
and nsl_bpg_offset in vds_cfg when native_420 is true
---v3
-adding display version check to solve igt issue
--v7
-remove is_pipe_dsc check as its always true for D14 [Jani]
--v10
-keep sink capability check [Jani]
-move from !(x == y || w == z) to x !=y && w != z [Jani]
--v11
-avoid native_420 computation if not gen14 [Uma]
--v12
-fix state mismatch issue of compressed_bpp
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-6-suraj.kandpal@intel.com
Implementation of VDSC for YCbCr420.
Add QP tables for 8,10,12 BPC from rc_tables.h in intel_qp_tables.c
(Derived from C-Model, which is given along with DSC1.2a Spec from Vesa)
intel_lookup_range_min/max_qp functons need to take into account the
output format. Based on that appropriate qp table need to be chosen.
Other rc_parameters need to be set where currently values for 444 format
is hardcoded in calculate_rc_parameters( ).
vdsc_cfg struct needs to be filled with output format information, where
these are hardcoded for 444 format.
Bspec: 49259
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Vandita Kulkarni <Vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-5-suraj.kandpal@intel.com
