DC 3.2.303 contains some improvements as summarized below:
* Improve brightness control
* Add support for UHBR10 eDP
* OPTC required only for DTBCLK_P for dcn401
* Fix TBT monitor resume issue
* Code cleanup
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DTBCLK_P is used to generate virtual pixel clock, and to drive the HPO
stream encoder clock. Programming the required clock when
enabling/disabling both components can cause issues.
For example, if HPO is being disabled and clock source is changed to
REFCLK, virtual pixel rate will then be wrong, causing issues in CRTC.
[HOW]
Only program the DTBCLK_P when programming CRTC, as its expected it will
be enabled prior to HPO, and disabled after HPO in all valid cases.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enables starting and stopping IPS residency measurements
and querying the IPS residency information consisting of residency
percent, entry counter, total time active & inactive, and histograms
for the specified IPS mode.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
A number of values are assigned to variables but the stored values are
not used afterwards.
[HOW]
The assignments are removed. If the variables are not used, they are
removed as well.
This fixes 9 UNUSED_VALUE issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
MacroTileSizeBytes is set to either 256 or 65535 and it is never
4096. Its branch is not taken, and should be removed. Similarly,
mode_422 is always 0 and thus ppe will always be 1. The ternary
operator should be removed.
This fixes 2 DEADCODE issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prioritize Aux-based over PWM-based brightness control
for more types of panels and introduce a new structure
to store and manage the type of brightness control used.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Muyuan Yang <muyuan.yang@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some issues which customer only can provide full
dump for analyze, without register history, it's hard to
debug HW status.
[How]
1. Put register read/write into WPP log so we can trace the logs
from full memory dump.
2. MALL doesn't add into WPP, add it.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Connected with a Thunderbolt monitor and do the suspend and the system
may hang while resume.
The TBT monitor HPD will be triggered during the resume procedure
and call the drm_client_modeset_probe() while
struct drm_connector connector->dev->master is NULL.
It will mess up the pipe topology after resume.
[How]
Skip the TBT monitor HPD during the resume procedure because we
currently will probe the connectors after resume by default.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If two monitors with TMDS signals were timing synced and one was
disconnected, the stream would go out of sync too early due to
the PLL turning off and the system could hang
[How]
On link disable output, change PHY FSM transition from TX_EN-to-PHY_OFF
to TX_EN-to-PLL_ON for TMDS
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are more IPS modes other than DMUB_IPS_ENABLE that enables IPS. We
need to enable the hotplug detect idle workqueue for those modes as
well.
[How]
Modify the if condition to initialize the workqueue in all IPS modes
except for DMUB_IPS_DISABLE_ALL.
Fixes: 65444581a4 ("drm/amd/display: Determine IPS mode by ASIC and PMFW versions")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current state should be used when waiting for DET update
instead of new context.
For any streams decreasing in DET, pipes used in the current state
should be checked since those pipes need to free their DET before
DET can be reallocated.
[How]
Pass in current_state instead of context.
Use pipe from current_state instead of context. This assumes that
pipe in the current_state is an OTG_MASTER pipe if the pipe in the context is an OTG_MASTER pipe.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where an MPO plane is being dragged around partially off-screen,
it is possible to get a flip where the only scaling parameters to change
are the clip rect size and position. Currently, clip rect size changes
are considered medium updates, which can result in the clip rect being used
for HW programming being larger than the clip rect that was used for the
last DML validation. This can lead to mismatches in different parts of the
pipe and can result in a p-state hang.
[How]
- consider clip rect size changes scaling changes, therefore full updates
- refactor get_scaling_info_update_type for clarity
- remove clip_size_change update flag
Clip rect size changes were previously demoted from full updates as an
optimization when the MPO + ODM policy changed to always pre-allocate MPO
pipes, but it created the issue described above. Personally testing this
use case, the performance feels fine with full update spam, and we expect
this is a fairly infrequent use case. If the performance needs to be
optimized in the future, consider reworking the entire update type logic
to run a DML pass and determine the update type based on what DML says
will actually change.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Certain transitions from HW to SW cursor can be missed, which will
result in black visual confirm instead of expected blue/red. Need to add
handling for cursor visual confirm to dc_update_visual_confirm_color.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Videos using YUV420 format may result in high power being used.
Disabling MPO may result in lower power usage.
Update interface that can be used to check power profile of a dc_state.
[How]
Allow pstate switching in VBlank as last entry in strategy candidates.
Add helper functions that can be used to determine power level:
-get power profile after a dc_state has undergone full validation
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The "dpp35_dppclk_control" routine is incorrectly disabling the register clock gater
when the DPP is enabled.
The "DISPCLK_R_GATE_DISABLE" should never be set to 1 in the normal operating mode.
This will disable the clock gater and the DPPCLK register clock branch will always be running.
As a consequence, the dynamic power will be higher than expected.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently the absence of UHBR cable ID caps from USB-C PD does not block UHBR
rates. In situations where DPCD reports valid UHBR capability but USB-C PD
does not, such as using a USB-C to DP1.4 dongle connected to a native DP2.1
cable, link loss and lightup failures can be seen as a result.
Additionally, in edge cases where a platform supports cable ID but DMUB
doesn't correctly return cable ID caps, driver currently also allows UHBR.
[HOW]
Block UHBR rates over DP alt mode if cable id indicates no UHBR support.
Additionally, block UHBR rates if a cable ID supported platform receives no
reply from a DMUB cable id query.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current pipe unlock order set within dcn401_interdependent_update_lock.
Separate the logic from the functionality to allow for unit testing
and make it easier to debug.
[How]
Add a flag to indicate if a pipe unlock order should be set.
Create function to determine unlock order.
Indicate which pipes should be unlocked first using
array stored in dc scratch memory.
Pipes indicated in array can be unlocked in any order.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A stream without dsc_aux should not be eliminated from
the dsc determination. Whether it needs a dsc recompute depends on
whether its mode has changed or not. Eliminating such a no-dsc stream
from the dsc determination policy will end up with inconsistencies
in the new dc_state when compared to the current dc_state,
triggering a dsc recompute that should not have happened.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Turning off OTG before DIG is on and backlight is on, might cause:
DIG FIFO underflow.
EDP output unexpected video data. That might violate EDP spec.
EDP spec requires black light should be off before validate
video data is turned off.
Currently garbage issue only occurs in one type of EDP to MIPI converter.
[How]
Add monitor patch to call blank_stream() before disable_crtc().
That will be no impact for current sequence.
If there are more types of EDP panels meeting this issue later,
we might remove this monitor patch and fix the current sequence.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Existing last step of dsc policy is to restore pbn value under minimum compression
when try to greedily disable dsc for a stream failed to fit in MST bw.
Optimized dsc params result from optimization step is not necessarily the minimum compression,
therefore it is not correct to restore the pbn under minimum compression rate.
Restore the pbn under minimum compression instead of the value from optimized pbn could result
in the dsc params not correct at the modeset where atomic_check failed due to not
enough bw. One or more monitors connected could not light up in such case.
Restore the optimized pbn value, instead of using the pbn value under minimum
compression.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add partition config nodes in sysfs to get resource instance details for
a particular partition mode. A resource could be anything like an xcc,
vcn decoder, system dma units etc.
Details of various resource instances are available under
/sys/bus/pci/devices/.../compute_partition_config/
Select a partition configuration:
/sys/bus/pci/devices/.../compute_partition_config/xcp_config
Number of instances of a resource:
/sys/bus/pci/devices/.../compute_partition_config/<rsrc_name>/num_inst
Total partitions sharing the resource:
/sys/bus/pci/devices/.../compute_partition_config/<rsrc_name>/num_shared
v2: Update node name as per spec
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A reset on initialization will be needed if a new PSP TOS needs to be
loaded than the one currently active on the system. This is possible
only on SOCs which support a full device reset which results in unload
of active PSP TOS.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a separate function to read badpage data during initialization.
Reading bad pages will need hardware access and cannot be done during
reset. Hence in cases where device needs a full reset during
init itself, attempting to read will cause a deadlock.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_i2c_add and amdgpu_i2c_init were added in 2015's commit
d38ceaf99e ("drm/amdgpu: add core driver (v4)")
but never used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
