Add device tree overlay to support the MayQueen PixPaper e-paper display
on the Renesas RZ/V2H EVK (KAKIP board). The display is connected via
SPI0 interface and uses GPIO pins for reset, busy, and DC control.
The overlay configures:
- RSPI0 pinmux for SPI communication (MOSI, MISO, CLK, CE0),
- PixPaper display device with proper GPIO assignments,
- SPI frequency set to 1MHz for stable operation.
This enables support for the Open-EP Community pixpaper-213-c module on
the RZ/V2H platform.
Signed-off-by: Wig Cheng <onlywig@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260124163611.3279104-1-onlywig@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Armadillo-800EVA board provides an SD card slot and an AWL13 SDIO
interface connected to the SDHI1 controller. Routing between these two
interfaces is controlled by a mechanical DIP switch and a set of
multiplexers.
To support this, add:
- A fixed 3.3V regulator for SDHI1 power, controlled by PORT16 (G2),
- SDHI1 pinmux groups for data, control, and card detection,
- A gpio-hog for PORT6 (J5) to control the SDHI1/AWLAN multiplexer.
PORT176 (N21) is already configured as output-high in this DTS (via
lcd0-mux-hog), routing the SDSLOT2_ENABLE signal to PORT6. Since the
hardware includes an external 10k pull-up resistor (R94) on this line,
PORT6 is configured as an input to allow the physical DIP switch to
determine the routing without SoC interference.
Both configurations have been verified:
- SD card (CON8): detected as mmcblk1, high-speed SDHC,
- SDIO (CON14): detected as mmc1, high-speed SDIO.
Signed-off-by: bui duc phuc <phucduc.bui@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260224074532.60046-1-phucduc.bui@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on Ebisu
board. The clock generator supplies 100 MHz differential clock for both
PCIe slot and BT/WLAN expansion port, as well as for the USB 3.0 PHY.
This configuration is valid for SW49 in OFF position, which means the
PCIe signals are routed to the PCIe slot and U11 9FGV0841 PCIe clock
generator output 3 supplies clock to the PCIe slot.
In case the SW49 is set to ON position, which means the PCIe signals
are routed to the EX BT/WLAN expansion port, and U11 9FGV0841 PCIe
clock generator output 4 supplies clock to the port and &pciec0_rp
clocks should be changed to "clocks = <&pcie_usb_clk 4>;". Once the
BT/WLAN port is tested, this can be implemented using a DTO. Until
then, assume SW49 is set to OFF position.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on ULCB
boards. The clock generator supplies 100 MHz differential clock for
both PCIe ports, the USB 3.0 PHY and SATA.
SATA is not yet described in the ULCB DT, therefore the connection to
this clock generator is not described here either.
The H3 ULCB schematic does describe connection from output DIF7 to
USB3S1_CLK_*, but these signals do not exist on the SoC, therefore
this connection is also not described.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the
'ref' clock frequency value is set to 500 MHz which is the default 'ref'
clock frequency value.
Add support for CPU frequency scaling defining those 3 frequencies in
the opp-table with the assumption that the 'ref' clock is set to its
default value.
Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260115164905.1203453-1-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The U-Boot SPL is responsible for initializing the hardware and it does
also initialize HSCIF0 and its pinmux, mark the HSCIF0 pinmux as needed
in all bootloader stages. The SPL also uses OTP to determine the exact
V4H SoC variant during DRAM initialization, to determine which is the
maximum allowed DRAM rate, mark OTP as required in all bootloader stages
as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260112234642.225993-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The default settings for the Versa3 device on the Renesas RZ/G3S SMARC
SoM board have PLL2 disabled. PLL2 was later enabled together with audio
support, as it is required to support both 44.1 kHz and 48 kHz audio.
With PLL2 enabled, it was observed that Linux occasionally either hangs
during boot (the last log message being related to the I2C probe) or
randomly crashes. This was mainly reproducible on cold boots. During
debugging, it was also noticed that the Unicode replacement character (�)
sometimes appears on the serial console. Further investigation traced this
to the configuration applied through the Versa3 register at offset 0x1c,
which controls PLL enablement.
The appearance of the Unicode replacement character suggested an issue
with the SoC reference clock. The RZ/G3S reference clock is provided by
the Versa3 clock generator (REF output).
After checking with the Renesas Versa3 hardware team, it was found that
this is related to the PLL2 lock bit being set through the
renesas,settings DT property.
The PLL lock bit must be set to avoid unstable clock output from the PLL.
However, due to the Versa3 hardware design, when a PLL lock bit is set,
all outputs (including the REF clock) are temporarily disabled until the
configured PLLs become stable.
As an alternative, the bypass bit can be used. This does not interrupt the
PLL2 output or any other Versa3 outputs, but it may result in temporary
instability on PLL2 output while the configuration is applied. Since PLL2
feeds only the audio path and audio is not used during early boot, this is
acceptable and does not affect system boot.
Drop the PLL2 lock bit and set the bypass bit instead.
This has been tested with more than 1000 cold boots.
Fixes: a94253232b ("arm64: dts: renesas: rzg3s-smarc-som: Add versa3 clock generator node")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260302135703.162601-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The HW user manual for the Renesas RZ/V2H(P) SoC (a.k.a r9a09g057)
states that only WDT1 is supposed to be accessed by the CA55 cores.
WDT0 is supposed to be used by the CM33 core, WDT2 is supposed
to be used by the CR8 core 0, and WDT3 is supposed to be used
by the CR8 core 1.
Remove wdt{0,2,3} from the SoC specific device tree to make it
compliant with the specification from the HW manual.
This change is harmless as there are currently no users of the
wdt{0,2,3} device tree nodes, only the wdt1 node is actually used.
Fixes: 095105496e ("arm64: dts: renesas: r9a09g057: Add WDT0-WDT3 nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260203124247.7320-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Set an appropriate ramp delay for the SD0 I/O voltage regulator in the
CN15 SD overlay to make UHS-I voltage switching reliable during card
initialization.
This issue was observed on the RZ/V2H EVK, while the same UHS-I cards
worked on the RZ/V2N EVK without problems. Adding the ramp delay makes
the behavior consistent and avoids SD init timeouts.
Before this change SD0 could fail with:
mmc0: error -110 whilst initialising SD card
With the delay in place UHS-I cards enumerate correctly:
mmc0: new UHS-I speed SDR104 SDXC card at address aaaa
mmcblk0: mmc0:aaaa SR64G 59.5 GiB
mmcblk0: p1
Fixes: 3d6c2bc762 ("arm64: dts: renesas: Add CN15 eMMC and SD overlays for RZ/V2H and RZ/V2N EVKs")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260123225957.1007089-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a ramp delay of 60 uV/us to the vqmmc_sdhi0 voltage regulator to
fix UHS-I SD card detection failures.
Measurements on CN78 pin 4 showed the actual voltage ramp time to be
21.86ms when switching between 3.3V and 1.8V. A 25ms ramp delay has
been configured to provide adequate margin. The calculation is based
on the voltage delta of 1.5V (3.3V - 1.8V):
1500000 uV / 60 uV/us = 25000 us (25ms)
Prior to this patch, UHS-I cards failed to initialize with:
mmc0: error -110 whilst initialising SD card
After this patch, UHS-I cards are properly detected on SD0:
mmc0: new UHS-I speed SDR104 SDXC card at address aaaa
mmcblk0: mmc0:aaaa SR64G 59.5 GiB
Fixes: d065453e5e ("arm64: dts: renesas: rzt2h-rzn2h-evk: Enable SD card slot")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260123225957.1007089-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pull fsverity fixes from Eric Biggers:
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux:
fsverity: fix build error by adding fsverity_readahead() stub
fsverity: remove fsverity_verify_page()
f2fs: make f2fs_verify_cluster() partially large-folio-aware
f2fs: remove unnecessary ClearPageUptodate in f2fs_verify_cluster()
Pull crypto library fix from Eric Biggers:
"Fix a big endian specific issue in the PPC64-optimized AES code"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: powerpc/aes: Fix rndkey_from_vsx() on big endian CPUs
Stephen retired and stepped back from -next maintainership, update his
entry in CREDITS to recognise his 18 years of hard work making it what
it is today and all the impact it's had on our development process.
Also update to his current GnuPG key while we're here.
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x509 public key code gained a dependency on the sha256 hash
implementation, causing a rare link time failure in randconfig
builds:
arm-linux-gnueabi-ld: crypto/asymmetric_keys/x509_public_key.o: in function `x509_get_sig_params':
x509_public_key.c:(.text.x509_get_sig_params+0x12): undefined reference to `sha256'
arm-linux-gnueabi-ld: (sha256): Unknown destination type (ARM/Thumb) in crypto/asymmetric_keys/x509_public_key.o
x509_public_key.c:(.text.x509_get_sig_params+0x12): dangerous relocation: unsupported relocation
Select the necessary library code from Kconfig.
Fixes: 2c62068ac8 ("x509: Separately calculate sha256 for blacklist")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Align to the commit bf4afc53b7 ("Convert 'alloc_obj' family to use the
new default GFP_KERNEL argument") update the 'kmalloc_obj' declaration
for userspace to fix below compile error:
In file included from arch/arm/boot/compressed/../../../../lib/decompress_unxz.c:241,
from arch/arm/boot/compressed/decompress.c:56:
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'xz_dec_init':
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c:787:28: error: implicit declaration of function 'kmalloc_obj'; did you mean 'kmalloc'? [-Wimplicit-function-declaration]
787 | struct xz_dec *s = kmalloc_obj(*s);
| ^~~~~~~~~~~
| kmalloc
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Fixes: 69050f8d6d ("treewide: Replace kmalloc with kmalloc_obj for non-scalar types")
Fixes: bf4afc53b7 ("Convert 'alloc_obj' family to use the new default GFP_KERNEL argument")
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull RTC updates from Alexandre Belloni:
- loongson: Loongson-2K0300 support
- s35390a: nvmem support
- zynqmp: rework calibration
* tag 'rtc-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1390: fix number of bytes read from RTC
rtc: class: Remove duplicate check for alarm
rtc: optee: simplify OP-TEE context match
rtc: interface: Alarm race handling should not discard preceding error
rtc: s35390a: implement nvmem support
rtc: loongson: Add Loongson-2K0300 support
dt-bindings: rtc: loongson: Document Loongson-2K0300 compatible
dt-bindings: rtc: loongson: Correct Loongson-1C interrupts property
dt-bindings: rtc: renesas,rz-rtca3: Add RZ/V2N support
dt-bindings: rtc: cpcap: convert to schema
rtc: zynqmp: use dynamic max and min offset ranges
rtc: zynqmp: rework set_offset
rtc: zynqmp: rework read_offset
rtc: zynqmp: check calibration max value
rtc: zynqmp: correct frequency value
rtc: amlogic-a4: Remove IRQF_ONESHOT
rtc: pcf8563: use correct of_node for output clock
rtc: max31335: use correct CONFIG symbol in IS_REACHABLE()
rtc: nvvrs: Add ARCH_TEGRA to the NV VRS RTC driver
Pull rust fixes from Miguel Ojeda:
"Toolchain and infrastructure:
- Pass '-Zunstable-options' flag required by the future Rust 1.95.0
- Fix 'objtool' warning for Rust 1.84.0
'kernel' crate:
- 'irq' module: add missing bound detected by the future Rust 1.95.0
- 'list' module: add missing 'unsafe' blocks and placeholder safety
comments to macros (an issue for future callers within the crate)
'pin-init' crate:
- Clean Clippy warning that changed behavior in the future Rust
1.95.0"
* tag 'rust-fixes-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: list: Add unsafe blocks for container_of and safety comments
rust: pin-init: replace clippy `expect` with `allow`
rust: irq: add `'static` bounds to irq callbacks
objtool/rust: add one more `noreturn` Rust function
rust: kbuild: pass `-Zunstable-options` for Rust 1.95.0
Pull runtime verifier fix from Steven Rostedt:
- Fix multiple definition of __pcpu_unique_da_mon_this
After refactoring monitors, we used static per-cpu variables with the
same names across different per-cpu monitors. This is explicitly
disallowed for modules on some architectures (alpha) or if
CONFIG_DEBUG_FORCE_WEAK_PER_CPU is enabled (e.g. Fedora's debug
kernel). Make sure all those variables have different names to avoid
compilation issues.
* tag 'trace-rv-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rv: Fix multiple definition of __pcpu_unique_da_mon_this
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
