Ensure that the DAC output is enabled at the correct time by
moving it to the DCE link encoder similarly to how digital
outputs are enabled.
This also removes the call to DAC1EncoderControl from the DCE
HWSS, which always felt like it was a hacky solution.
Fixes: 0fbe321a93 ("drm/amd/display: Implement DCE analog link encoders (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Tested-by: Mauro Rossi <issor.oruam@gmail.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Apparently the VBIOS SelectCRTC_Source function overwrites
a few registers (such as FMT_*) which DC writes in a different
place, which can cause problems.
Instead of using the SelectCRTC_Source function from the
VBIOS, use the DAC_SOURCE_SELECT register directly, similarly
to how it is done for digital link encoders.
Fixes: 3be26d81b1 ("drm/amd/display: Support DAC in dce110_hwseq")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Tested-by: Mauro Rossi <issor.oruam@gmail.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The VBIOS DAC1EncoderControl() function can initialize the DAC,
by writing board-specific values to certain registers.
Call this at link encoder hardware initialization time similarly
to how the equivalent UNIPHYTransmitterControl initialization
is done.
This fixes DAC output on the Radeon HD 7790.
Also remove the ENCODER_CONTROL_SETUP enum from the
dac_encoder_control_prepare_params function which is actually
not a supported operation for DAC encoders.
Fixes: 0fbe321a93 ("drm/amd/display: Implement DCE analog link encoders (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Tested-by: Mauro Rossi <issor.oruam@gmail.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Apparently, the VBIOS DAC1EncoderControl function is much more
graceful about turning off the DAC. It writes various DAC
registers in a specific sequence. Use that instead of just
clearing the DAC_ENABLE register.
Do this in just the dce110_link_encoder_disable_output
function and remove it from the HWSS.
Fixes: 0fbe321a93 ("drm/amd/display: Implement DCE analog link encoders (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Tested-by: Mauro Rossi <issor.oruam@gmail.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The analog engine is already there in the link_analog_engine
variable and assigned to enc_init_data.analog_engine already.
I suspect this was a rebase mistake.
Fixes: 436d0d22aa ("drm/amd/display: Pass proper DAC encoder ID to VBIOS")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Tested-by: Mauro Rossi <issor.oruam@gmail.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It turned that using 4 level page tables on GMC generations which support
57bit VAs actually doesn't work at all.
Background is that the GMC actually can't switch between 4 and 5 levels,
but rather just uses a subset of address space when less than 5 levels are
selected.
Philip already removed the automatically switch to 4levels, now fix it as
well should it be enabled by module parameters.
v2: fix AMDGPU_GMC_HOLE_MASK as well, fix off by one issue pointed out
by Philip
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
xgmi support atomics between links. Set them to true. This only set for
GFX12 onwards to avoid regression on older generations
v2: Use correct xgmi flag that indicates CPU connection
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes issues when the code moves forward with a potential
NULL pointer, without checking.
Removed one redundant NULL check for a function parameter. This check
is already done in the only caller.
Signed-off-by: Andrew Martin <andrew.martin@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The plane scaling hw seems to have the same min/max plane scaling limits
for all 16 bpc / 64 bpp interleaved pixel color formats.
Therefore add cases to amdgpu_dm_plane_get_min_max_dc_plane_scaling() for
all the 16 bpc fixed-point / unorm formats to use the same .fp16
up/downscaling factor limits as used by the fp16 floating point formats.
So far, 16 bpc unorm formats were not handled, and the default: path
returned max/min factors for 32 bpp argb8888 formats, which were wrong
and bigger than what many DCE / DCN hw generations could handle.
The result sometimes was misscaling of framebuffers with
DRM_FORMAT_XRGB16161616, DRM_FORMAT_ARGB16161616, DRM_FORMAT_XBGR16161616,
DRM_FORMAT_ABGR16161616, leading to very wrong looking display, as tested
on Polaris11 / DCE-11.2.
So far this went unnoticed, because only few userspace clients used such
16 bpc unorm framebuffers, and those didn't use hw plane scaling, so they
did not experience this issue.
With upcoming Mesa 26 exposing 16 bpc unorm formats under both OpenGL
and Vulkan under Wayland, and the upcoming GNOME 50 Mutter Wayland
compositor allowing for direct scanout of these formats, the scaling
hw will be used on these formats if possible for HiDPI display scaling,
so it is important to use the correct hw scaling limits to avoid wrong
display.
Tested on AMD Polaris 11 / DCE 11.2 with upcoming Mesa 26 and GNOME 50
on HiDPI displays with scaling enabled. The mutter Wayland compositor now
correctly falls back to scaling via desktop compositing instead of direct
scanout, thereby avoiding wrong image display. For unscaled mode, it
correctly uses direct scanout.
Fixes: 580204038f ("drm/amd/display: Enable support for 16 bpc fixed-point framebuffers.")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This solves a priority inversion issue, caused by the language
runtime making high-priority queues wait for activity on
lower-priority queues.
Signed-off-by: Andrew Martin <andrew.martin@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Shaper programming has high chance to fail on first time after
power-on or reboot. This can be verified by running IGT's kms_colorop.
[How]
Always power on the shaper and 3DLUT before programming by
removing the debug flag of low power mode.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fix fastboot broken in driver.
This is caused by an open source backport change 7495962c.
from the comment, the intended check is to disable fastboot
for pre-DCN10. but the logic check is reversed, and causes
fastboot to be disabled on all DCN10 and after.
fastboot is for driver trying to pick up bios used hw setting
and bypass reprogramming the hw if dc_validate_boot_timing()
condition meets.
Fixes: 7495962cbc ("drm/amd/display: Disable fastboot on DCE 6 too")
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <Mario.Limonciello@amd.com>
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This gets rid of a header that is only used once. The copyrights and
license specifications are all already covered in the au1100fb.c file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The global wrappers also have the advantage to do stricter format
checking, so the pr_devel formats are also checked if DEBUG is not
defined. The global variants only check for DEBUG being defined and not
its actual value, so the #define to zero is dropped, too.
There is only a slight semantic change as the (by default disabled)
debug output doesn't contain __FILE__ any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The header asm/mach-au1x00/au1000.h is unused apart from pulling in
<linux/delay.h> (for mdelay()) and <linux/io.h> (for KSEG1ADDR()). Then
the only platform specific part in the driver is the usage of the KSEG1ADDR
macro, which for the non-mips case can be stubbed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Helge Deller <deller@gmx.de>
%zu is the dedicated type for size_t. %d only works on 32bit
architectures where size_t is typedef'd to be unsigned int. (And then
the signedness doesn't fit, but `gcc -Wformat` doesn't stumble over this.
Also the size of dma_addr_t is architecture dependent and it should be
printkd using %pad (and the value passed by reference).
This prepares allowing this driver to be compiled on non-mips platforms.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Using global data to store device specific data is a bad pattern that
breaks if there is more than one device. So expand driver data and drop
the global variables.
While there is probably no machine that has two or more au1100fb
devices, this makes the driver a better template for new drivers and
saves some memory if there is no such bound device.
bloat-o-meter reports (for ARCH=arm allmodconfig + CONFIG_FB_AU1100=y
and ignoring the rename of the init function):
add/remove: 1/4 grow/shrink: 2/2 up/down: 1360/-4800 (-3440)
Function old new delta
au1100fb_drv_probe 2648 3328 +680
$a 12808 13484 +676
au1100fb_drv_resume 404 400 -4
au1100fb_fix 68 - -68
au1100fb_var 160 - -160
fbregs 2048 - -2048
$d 9525 7009 -2516
Total: Before=38664, After=35224, chg -8.90%
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Save a local pointer to new_sock->sk and hold a reference before
installing callbacks in rds_tcp_accept_one. After
rds_tcp_set_callbacks() or rds_tcp_reset_callbacks(), tc->t_sock is
set to new_sock which may race with the shutdown path. A concurrent
rds_tcp_conn_path_shutdown() may call sock_release(), which sets
new_sock->sk = NULL and may eventually free sk when the refcount
reaches zero.
Subsequent accesses to new_sock->sk->sk_state would dereference NULL,
causing the crash. The fix saves a local sk pointer before callbacks
are installed so that sk_state can be accessed safely even after
new_sock->sk is nulled, and uses sock_hold()/sock_put() to ensure
sk itself remains valid for the duration.
Fixes: 826c1004d4 ("net/rds: rds_tcp_conn_path_shutdown must not discard messages")
Reported-by: syzbot+96046021045ffe6d7709@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=96046021045ffe6d7709
Signed-off-by: Allison Henderson <achender@kernel.org>
Link: https://patch.msgid.link/20260216222643.2391390-1-achender@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent cleanups and code consolidations in the s390 tape device driver
renamed files and function namespaces from tape_34xx to tape_3490 to
better reflect the single support of the IBM 3490E device in the
codebase.
These changes also renamed the driver name to tape_3490, which
consequently broke userspace as the sysfs driver path is now
/sys/bus/ccw/drivers/tape_3490/ instead of
/sys/bus/ccw/drivers/tape_34xx/.
Change the device driver name back to tape_34xx to fix userspace.
Fixes: 9872dae610 ("s390/tape: Rename tape_34xx.c to tape_3490.c")
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
For SQE128, sqe->cmd provides 80 bytes for uring_cmd. Add macro to
check if size of user struct does not exceed 80 bytes at compile time.
User doesn't have to track this manually during development.
Replace io_uring_sqe_cmd() inline func with macro and add
io_uring_sqe128_cmd() which checks struct
size for 16 bytes cmd and 80 bytes cmd respectively.
Signed-off-by: Govindarajulu Varadarajan <govind.varadar@gmail.com>
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_should_commit(), io_uring_classic_poll(), and io_do_iopoll() compare
struct io_kiocb's opcode against IORING_OP_URING_CMD to implement
special treatment for uring_cmds. The recently added opcode
IORING_OP_URING_CMD128 is meant to be equivalent to IORING_OP_URING_CMD,
so treat it the same way in these functions.
Fixes: 1cba30bf9f ("io_uring: add support for IORING_SETUP_SQE_MIXED")
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
gcc-16 warns about an instance that older compilers did not:
arch/arm64/mm/hugetlbpage.c: In function 'huge_pte_clear':
arch/arm64/mm/hugetlbpage.c:369:57: error: parameter 'addr' set but not used [-Werror=unused-but-set-parameter=]
The issue here is that __pte_clear() does not actually use its second
argument, but when CONFIG_ARM64_CONTPTE is enabled it still gets
updated.
Replace the macro with an inline function to let the compiler see
the argument getting passed down.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dev Jain <dev.jain@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Quentin forwards a report from Hyesoo Yu, describing an interesting
problem with the use of WFxT in __delay() when a vcpu is loaded and
that KVM is *not* in VHE mode (either nVHE or hVHE).
In this case, CNTVOFF_EL2 is set to a non-zero value to reflect the
state of the guest virtual counter. At the same time, __delay() is
using get_cycles() to read the counter value, which is indirected to
reading CNTPCT_EL0.
The core of the issue is that WFxT is using the *virtual* counter,
while the kernel is using the physical counter, and that the offset
introduces a really bad discrepancy between the two.
Fix this by forcing the use of CNTVCT_EL0, making __delay() consistent
irrespective of the value of CNTVOFF_EL2.
Reported-by: Hyesoo Yu <hyesoo.yu@samsung.com>
Reported-by: Quentin Perret <qperret@google.com>
Reviewed-by: Quentin Perret <qperret@google.com>
Fixes: 7d26b0516a ("arm64: Use WFxT for __delay() when possible")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/ktosachvft2cgqd5qkukn275ugmhy6xrhxur4zqpdxlfr3qh5h@o3zrfnsq63od
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
ASoC: Fixes for v7.0 merge window
A reasonably small set of fixes and quriks that came in during the merge
window, there's one more pending that I'll send tomorrow if you didn't
send a PR already.
`clippy` has changed behavior in [1] (Rust 1.95) where it no longer
warns about the `let_and_return` lint when a comment is placed between
the let binding and the return expression. Nightly thus fails to build,
because the expectation is no longer fulfilled.
Thus replace the expectation with an `allow`.
[ The errors were:
error: this lint expectation is unfulfilled
--> rust/pin-init/src/lib.rs:1279:10
|
1279 | #[expect(clippy::let_and_return)]
| ^^^^^^^^^^^^^^^^^^^^^^
|
= note: `-D unfulfilled-lint-expectations` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(unfulfilled_lint_expectations)]`
error: this lint expectation is unfulfilled
--> rust/pin-init/src/lib.rs:1295:10
|
1295 | #[expect(clippy::let_and_return)]
| ^^^^^^^^^^^^^^^^^^^^^^
- Miguel ]
Link: https://github.com/rust-lang/rust-clippy/pull/16461 [1]
Signed-off-by: Benno Lossin <lossin@kernel.org>
Cc: stable@vger.kernel.org # Needed in 6.18.y and later.
Link: https://patch.msgid.link/20260215132232.1549861-1-lossin@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
These callback functions take a generic `T` that is used in the body as
the generic argument in `Registration` and `ThreadedRegistration`. Those
types require `T: 'static`, but due to a compiler bug this requirement
isn't propagated to the function. Thus add the bound. This was caught in
the upstream Rust CI [1].
[ The three errors looked similar and will start appearing with Rust
1.95.0 (expected 2026-04-16). The first one was:
error[E0310]: the parameter type `T` may not live long enough
Error: --> rust/kernel/irq/request.rs:266:43
|
266 | let registration = unsafe { &*(ptr as *const Registration<T>) };
| ^^^^^^^^^^^^^^^^^^^^^^
| |
| the parameter type `T` must be valid for the static lifetime...
| ...so that the type `T` will meet its required lifetime bounds
|
help: consider adding an explicit lifetime bound
|
264 | unsafe extern "C" fn handle_irq_callback<T: Handler + 'static>(_irq: i32, ptr: *mut c_void) -> c_uint {
| +++++++++
- Miguel ]
Link: https://github.com/rust-lang/rust/pull/149389 [1]
Signed-off-by: Benno Lossin <lossin@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 29e16fcd67 ("rust: irq: add &Device<Bound> argument to irq callbacks")
Reviewed-by: Gary Guo <gary@garyguo.net>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://lore.kernel.org/rust-for-linux/20260217222425.8755-1-cole@unwrap.rs/
Link: https://patch.msgid.link/20260214092740.3201946-1-lossin@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
When creating guest partition objects, the hypervisor may fail to
allocate root partition pages and return an insufficient memory status.
In this case, deposit memory using the root partition ID instead.
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Reviewed-by: Mukesh R <mrathor@linux.microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
The HV_STATUS_INSUFFICIENT_CONTIGUOUS_MEMORY status indicates that the
hypervisor lacks sufficient contiguous memory for its internal allocations.
When this status is encountered, allocate and deposit
HV_MAX_CONTIGUOUS_ALLOCATION_PAGES contiguous pages to the hypervisor.
HV_MAX_CONTIGUOUS_ALLOCATION_PAGES is defined in the hypervisor headers, a
deposit of this size will always satisfy the hypervisor's requirements.
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Reviewed-by: Mukesh R <mrathor@linux.microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Introduce hv_deposit_memory_node() and hv_deposit_memory() helper
functions to handle memory deposit with proper error handling.
The new hv_deposit_memory_node() function takes the hypervisor status
as a parameter and validates it before depositing pages. It checks for
HV_STATUS_INSUFFICIENT_MEMORY specifically and returns an error for
unexpected status codes.
This is a precursor patch to new out-of-memory error codes support.
No functional changes intended.
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Reviewed-by: Mukesh R <mrathor@linux.microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Replace direct comparisons of hv_result(status) against
HV_STATUS_INSUFFICIENT_MEMORY with a new hv_result_needs_memory() helper
function.
This improves code readability and provides a consistent and extendable
interface for checking out-of-memory conditions in hypercall results.
No functional changes intended.
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Reviewed-by: Mukesh R <mrathor@linux.microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Pull more non-MM updates from Andrew Morton:
- "two fixes in kho_populate()" fixes a couple of not-major issues in
the kexec handover code (Ran Xiaokai)
- misc singletons
* tag 'mm-nonmm-stable-2026-02-18-19-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib/group_cpus: handle const qualifier from clusters allocation type
kho: remove unnecessary WARN_ON(err) in kho_populate()
kho: fix missing early_memunmap() call in kho_populate()
scripts/gdb: implement x86_page_ops in mm.py
objpool: fix the overestimation of object pooling metadata size
selftests/memfd: use IPC semaphore instead of SIGSTOP/SIGCONT
delayacct: fix build regression on accounting tool
