pinctrl: renesas: Updates for v6.11
- Add support for the new RZ/V2H(P) (R9A09G057) Soc,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic pinctrl-scmi.c driver could not be used for i.MX95 because
i.MX95 SCMI firmware not supports functions, groups or generic
'Pin Configuration Type and Enumerations' listed in SCMI Specification.
i.MX95 System Control Management Interface(SCMI) firmware only supports
below pin configuration types which are OEM specific types:
192: PIN MUX
193: PIN CONF
194: DAISY ID
195: DAISY VAL
To Support fsl,pins property together with SCMI OEM protocol, add this
driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20240521-pinctrl-scmi-imx95-v1-3-9a1175d735fd@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PDC was hooked up as a wakeup parent in the DTS in
commit 71f080633d ("arm64: dts: qcom: sdm670: Hook up PDC as
wakeup-parent of TLMM"), but the wakeirq mapping was not defined so it
had no effect. Add the mapping for wakeup interrupts on the PDC to their
corresponding pins.
Configuring a pin IRQ as dual-edge would break it unless the
wakeirq_dual_edge_errata flag is set.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20240523230619.256882-2-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current version of the pinctrl driver has some issues:
1. Duplicated "gpio" pmx function
The common code will add a "gpio" pmx functon to every pin group, so
it's not necessary to define a separate "gpio" pmx function in pin
groups.
2. Duplicated pmx function name
There are some same function name in different pin groups, which will
cause some problems. For example, when we want to use PAD_GPIO0 as
refclk output function, the common clk framework code will search the
entire pin function lists, then return the first one matched, in this
case the matched function list only include the PAD_CO_CLKO pin group
because there are three "refclk" pin function, which is added by
refclk_grp, spi_cs1_grp and gpio_grp.
To solve this problem, a simple way is just add a pingrp refix to
function name like mt7620 pinctrl driver does.
3. Useless "-" or "rsvd" functon
It's really unnecessary to add a reserved pin mux function to the
function lists, because we never use it.
Signed-off-by: Weihao Li <cn.liweihao@gmail.com>
Link: https://lore.kernel.org/r/20240527022036.31985-1-user@blabla
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We were not resetting the pointer to the associated gpio_device once
we are done displaying a pin's information.
This meant that once we reached the end of a gpio-range, if there
were pins right after it that did not belong to any known range,
they would be associated with the previous range's gpio device.
This resulted in those pins appearing as <4294966783:old_gdev> instead
of the expected <0:?> (due to gpio_num being -1).
Signed-off-by: Léo DUBOIN <lduboin@freebox.fr>
Link: https://lore.kernel.org/r/c40d0634abefa19e689ffd450e0f48a8d63c4fc4.1714049455.git.lduboin@freebox.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We previously only looked at the 'pin_base' of the pinctrl_gpio_ranges
struct for determining if a pin matched a GPIO number.
This value is present only if the 'pins' array is not NULL,
and is 0 otherwise. This means that GPIO ranges declared using
gpiochip_add_pingroup_range(), thus making use of pins, were always matched
by the pins in the range [0-npins] even if they contained pins in a
completely separate range.
Signed-off-by: Léo DUBOIN <lduboin@freebox.fr>
Link: https://lore.kernel.org/r/6df39bd47942156be5713f8f4e317d2ad3e0ddeb.1714049455.git.lduboin@freebox.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add documentation for the pin controller found on the Renesas RZ/V2H(P)
(R9A09G057) SoC. The RZ/V2H PFC varies slightly compared to the RZ/G2L
family:
- Additional bits need to be set during pinmuxing,
- The GPIO pin count is different.
Hence, a SoC-specific compatible string, 'renesas,r9a09g057-pinctrl', is
added for the RZ/V2H(P) SoC.
Also, add the 'renesas,output-impedance' property. The drive strength
settings on RZ/V2H(P) depend on the different power rails coming out from
the PMIC (connected via I2C). These power rails (required for drive
strength) can be 1.2V, 1.8V, or 3.3V.
Pins are grouped into 4 groups:
Group 1: Impedance
- 150/75/38/25 ohms (at 3.3V)
- 130/65/33/22 ohms (at 1.8V)
Group 2: Impedance
- 50/40/33/25 ohms (at 1.8V)
Group 3: Impedance
- 150/75/37.5/25 ohms (at 3.3V)
- 130/65/33/22 ohms (at 1.8V)
Group 4: Impedance
- 110/55/30/20 ohms (at 1.8V)
- 150/75/38/25 ohms (at 1.2V)
The 'renesas,output-impedance' property, as documented, can be
[0, 1, 2, 3], these correspond to register bit values that can
be set in the PFC_IOLH_mn register, which adjusts the drive
strength value and is pin-dependent.
As power rail information may not be available very early in the boot
process, the 'renesas,output-impedance' property is added instead of
reusing the 'output-impedance-ohms' property.
Also, allow bias-disable, bias-pull-down and bias-pull-up properties
as these can be used to configure the pins.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240606085133.632307-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support to configure bias-disable, bias-pull-up, and bias-pull-down
properties of the pin.
Two new function pointers, hw_to_bias_param() and bias_param_to_hw(),
are introduced in the struct rzg2l_pinctrl_data to configure bias
settings, as the values in the PUPD register differ when compared to the
RZ/G2L family and the RZ/V2H(P) SoC.
Value | RZ/G2L | RZ/V2H
---------------------------------
00b: | Bias Disabled | Pull up/down disabled
01b: | Pull-up | Pull up/down disabled
10b: | Pull-down | Pull-down
11b: | Prohibited | Pull-up
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240530173857.164073-12-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Introduce function pointers oen_read() and oen_write(), in the struct
rzg2l_pinctrl_data to facilitate reading and writing to the PFC_OEN
register. On the RZ/V2H(P) SoC, unlocking the PWPR.REGWE_B bit before
writing to the PFC_OEN register is necessary, and the PFC_OEN register
has more bits compared to the RZ/G2L family. To handle these
differences between RZ/G2L and RZ/V2H(P) and to reuse the existing code
for RZ/V2H(P), these function pointers are introduced.
Additionally, populate these function pointers with appropriate data for
existing SoCs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://lore.kernel.org/r/20240530173857.164073-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Introduces pmc_writeb() function pointer, in the struct
rzg2l_pinctrl_data to facilitate writing to the PMC register. On the
RZ/V2H(P) SoC, unlocking the PWPR.REGWE_A bit before writing to PMC
registers is required, whereas this is not the case for the existing
RZ/G2L family. This addition enables the reuse of existing code for
RZ/V2H(P). Additionally, populate this function pointer with
appropriate data for existing SoCs.
Note that this functionality is only handled in rzg2l_gpio_request(), as
PMC unlock/lock during PFC setup will be taken care of in the
pwpr_pfc_lock_unlock() function pointer.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://lore.kernel.org/r/20240530173857.164073-9-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On the RZ/G2L SoC, the PFCWE bit controls writing to PFC registers.
However, on the RZ/V2H(P) SoC, the PFCWE (REGWE_A on RZ/V2H) bit controls
writing to both PFC and PMC registers. Additionally, BIT(7) B0WI is
undocumented for the PWPR register on RZ/V2H(P) SoC. To accommodate these
differences across SoC variants, introduce the pwpr_pfc_lock_unlock()
function pointer.
Note, in rzg2l_pinctrl_set_pfc_mode() the pwpr_pfc_lock_unlock(.., false)
is now called before PMC read/write and pwpr_pfc_lock_unlock(.., true) is
now called after PMC read/write this is to keep changes minimal for
RZ/V2H(P) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://lore.kernel.org/r/20240530173857.164073-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
