[Why]
On 14us for exit latency time causes underflow for 8K monitor with HDR on.
Increasing the latency to 28us fixes the underflow.
[How]
Increase the latency to 28us. This workaround should be sufficient
before we figure out why SR exit so long.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In current code, we recognize a pipe as a phantom pipe if it references
the same phantom stream. However it can also a phantom split pipe.
If the phantom split pipe has a smaller pipe index than the phantom pipe
we will mistakenly use the phantom split pipe as the phantom pipe. This
causes an incorrect subvp configuration where the first half of the
screen is flashing solid white image.
[how]
Add additional check that the pipe needs to be an OTG master pipe.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. To watch dmcub inbox1 ring buffer cmd type without tools
2. dmub_cmd_PLAT_54186_wa 66 bytes
[How]
Added dmcub cmd type enum: unsigned char for debug use only,
also fixed 66 bytes issue by using unsigned int in bit
define instead of unsigned char.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous patch to allow DTBCLK disable didn't address boot case. Driver
thinks DTBCLK is disabled by default, so we don't send disable message to
PMFW. DTBCLK is then enabled at idle desktop on boot, burning power.
[How]
Set dtbclk_en to true on boot so that disable message is sent during first
commit.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
fix reading edp rx crc timeout failure. after
bootup, kernel setup psr with dpcd 0x170 = 5. this
notify rx psr enable and let rx fw start checking crc
for fw internal logic. rx fw may not update crc read
count within dpcd 0x246. read count is always 0. this
will lead tx crc reading timeout.
[How]
add debugfs to let test app to disbable rx crc
checking for rx internal logic. then test app can read
rx crc dpcd 0x246 successfully.
expected app sequence is as below:
1. disable eDP PHY and notify eDP rx with dpcd 0x600 = 2.
2. echo 0x1 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr
3. enable eDP PHY and notify eDP rx with dpcd 0x600 = 1 but
without dpcd 0x170 = 5.
4. read crc from rx dpcd 0x270, 0x246, etc.
5. echo 0x0 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr.
this will let eDP back to normal with psr setup dpcd 0x170 = 5.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank
in FPO / SubVP / DRR cases will not have any effect
and we could hit underflow / corruption.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream
so there is no need to have two flags to control it. Unifying
this to a single flag allows dc_stream_adjust_vmin_vmax to skip
actual programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Originally, PMFW said min FCLK is 300Mhz, but min DCFCLK can be increased
to 400Mhz because min FCLK is now 600Mhz so FCLK >= 1.5 * DCFCLK hardware
requirement will still be satisfied. Increasing min DCFCLK addresses
underflow issues (underflow occurs when phantom pipe is turned on for some
Sub-Viewport configs).
[how]
Increasing DCFCLK by raising the min_dcfclk_mhz
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sohaib Nadeem <sohaib.nadeem@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want acknowledgment of the driver idle disallow from DMCUB before
continuing with any further programming.
For idle allow we want to minimize the chance of DMCUB actively
interacing with other firmware components on the system (eg. PMFW)
at the same time.
[How]
Ensure that DMCUB isn't in the middle of processing other command
submissions prior to allowing idle and after disallowing idle by
inserting a wait before the allow and by changing the wait type for
the idle disallow.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Partial migration to system memory should use migrate.addr, not
prange->start as virtual address to allocate system memory page.
Fixes: a546a27684 ("drm/amdkfd: Use partial migrations/mapping for GPU/CPU page faults in SVM")
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Xiaogang Chen <Xiaogang.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to eliminate interrupt warning below:
"[drm] Fence fallback timer expired on ring sdma0.0".
An early vm pt clearing job is sent to SDMA ahead of interrupt enabled.
And re-locating the drm client creation following after drm_dev_register
looks like a more proper flow.
v2: wrap the drm client creation
Fixes: 1819200166 ("drm/amdkfd: Export DMABufs from KFD using GEM handles")
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d ("drm/amd/display: add null checks before logging")
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In a non-FLR page avoidance scenario, the host driver will
provide the bad pages in the pf2vf exchange region.
Adding a new host response message to indicate when the
pf2vf exchange region has been updated.
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IPS was temporary disabled due to instability.
It was fixed in dmub firmware and with:
- "drm/amd/display: Add IPS checks before dcn register access"
- "drm/amd/display: Disable ips before dc interrupt setting"
[How]
Enable IPS by default.
Disable IPS if 0x800 bit set in amdgpu.dcdebugmask module params
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While in IPS2 an access to dcn registers is not allowed.
If interrupt results in dc call, we should disable IPS.
[How]
Safeguard register access in IPS2 by disabling idle optimization
before calling dc interrupt setting api.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- move aca init/fini function into ras init/fini to adapt gpu reset
sequence.
- add new function amdgpu_aca_reset()
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver unload hangs because the page retirement
kthread cannot be stopped as it is sleeping and waiting
on page retirement event to occur. Add kthread_should_stop()
to the event condition to wake up the kthread when kthread
stop is called during driver unload.
Fixes: 3fdcd0a31d ("drm/amdgpu: Prepare for asynchronous processing of umc page retirement")
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This needs to be set to 1 to avoid a potential deadlock in
the GC 10.x and newer. On GC 9.x and older, this needs
to be set to 0. This can lead to hangs in some mixed
graphics and compute workloads. Updated firmware is also
required for AQL.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This needs to be set to 1 to avoid a potential deadlock in
the GC 10.x and newer. On GC 9.x and older, this needs
to be set to 0. This can lead to hangs in some mixed
graphics and compute workloads. Updated firmware is also
required for AQL.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This allows kernel mapped pages like the PDB and PTB to be
read via the iomem debugfs when there is no vram in the system.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Power limit of SMUv13.0.6 SOCs can be updated by out-of-band ways. Fetch
the limit from firmware instead of using cached values.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
