Currently, statistics in arsta are updated at deflink for both non-ML
and multi-link(ML) station. Link statistics are not updated for
multi-link operation(MLO).
Hence, add support to correctly obtain the link ID if the peer is ML,
fetch the arsta from the appropriate link ID, and update the
statistics in the corresponding arsta.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250701105927.803342-3-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently rx and tx MCS map for 160 MHz under HE capabilities
are not updating properly, when 160 MHz is configured with NSS
lesser than max NSS support. Fix this by utilizing
nss_ratio_enabled and nss_ratio_info fields sent by firmware
in service ready event.
However, if firmware advertises EXT NSS BW support in VHT caps
as 1(1x2) and when nss_ratio_info indicates 1:1, reset the EXT
NSS BW Support in VHT caps to 0 which indicates 1x1. This is
to avoid incorrectly choosing 1:2 NSS ratio when using the
default VHT caps advertised by firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-10-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to configure maximum NSS in 160 MHz bandwidth.
Firmware advertises support for handling NSS ratio information
as a part of service ready ext event using nss_ratio_enabled
flag. Save this information in ath12k_pdev_cap to calculate
NSS ratio.
Additionally, reorder the code by moving
ath12k_peer_assoc_h_phymode() before ath12k_peer_assoc_h_vht()
to ensure that arg->peer_phymode correctly reflects the bandwidth
in the max NSS calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-9-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In rare cases, ath10k may lose connection with the PCIe bus due to
some unknown reasons, which could further lead to system crashes during
resuming due to watchdog timeout:
ath10k_pci 0000:01:00.0: wmi command 20486 timeout, restarting hardware
ath10k_pci 0000:01:00.0: already restarting
ath10k_pci 0000:01:00.0: failed to stop WMI vdev 0: -11
ath10k_pci 0000:01:00.0: failed to stop vdev 0: -11
ieee80211 phy0: PM: **** DPM device timeout ****
Call Trace:
panic+0x125/0x315
dpm_watchdog_set+0x54/0x54
dpm_watchdog_handler+0x57/0x57
call_timer_fn+0x31/0x13c
At this point, all WMI commands will timeout and attempt to restart
device. So set a threshold for consecutive restart failures. If the
threshold is exceeded, consider the hardware is unreliable and all
ath10k operations should be skipped to avoid system crash.
fail_cont_count and pending_recovery are atomic variables, and
do not involve complex conditional logic. Therefore, even if recovery
check and reconfig complete are executed concurrently, the recovery
mechanism will not be broken.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623022731.509-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During interface creation, following print is observed on the console -
Timeout while waiting for regulatory update
This occurs due to commit 906619a009 ("wifi: ath12k: handle regulatory
hints during mac registration"), which introduced a completion mechanism to
synchronize the regulatory update process. The intent behind this change is
to coordinate the timing between when the firmware sends regulatory data to
the driver and when the driver processes that data.
However, during interface addition, if the 6 GHz band is active, the driver
invokes ath12k_regd_update() to apply the appropriate 6 GHz power mode
regulatory settings. At this point, there is no interaction with the
firmware, so the completion object is not reinitialized. As a result,
wait_for_completion() eventually times out, leading to the observed error
log message.
Hence to fix this, move all complete() on regd_update_completed to
complete_all().
The complete() function signals only once, causing any subsequent waits
without reinitialization to timeout. In this scenario, since waiting is
unnecessary, complete_all() can be used instead, ensuring that subsequent
calls to wait without reinitialization will simply bail out and not
actually wait. This approach is ideal because if the firmware is not
involved, there is no need to wait for the completion event. However, if
the firmware is involved, it is guaranteed that the completion will be
reinitialized, and thus, it would wait.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-by: Kang Yang <kang.yang@oss.qualcomm.com>
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 906619a009 ("wifi: ath12k: handle regulatory hints during mac registration")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250626-fix_timeout_during_interface_creation-v1-1-90a7fdc222d4@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When setting a new bitrate, WMI peer association command is sent from
the host without the peer authentication bit set in peer_flags for
security mode, which causes ping failure.
The firmware handles peer_flags when the client is associating, as the
peer authentication bit in peer_flags is set after the key exchange.
When the WMI peer association command is sent from the host to update
the new bitrate for an associated STA, the firmware expects the WMI
peer authentication bit to be set in peer_flags.
Fix this issue by ensuring that the WMI peer auth bit is set in
peer_flags in WMI peer association command when updating the new
bitrate.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Thiraviyam Mariyappan <thiraviyam.mariyappan@oss.qualcomm.com>
Signed-off-by: Ramasamy Kaliappan <ramasamy.kaliappan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250608145651.1735236-1-ramasamy.kaliappan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-4-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath12k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath12k_hal_srng_access_end().
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath11k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath11k_hal_srng_access_end().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The power value is 6 dBm on an AP operating on the 6 GHz channel.
This is a very low value.
On 6 GHz, the target computes the EIRP based on the power values sent
in the WMI_VDEV_SET_TPC_POWER_CMD. Currently, this is being sent only
for station interfaces and not for AP interfaces.
Therefore, add AP vdev to the condition in
ath12k_mac_station_supports_tpc() and rename
ath12k_mac_station_supports_tpc() to ath12k_mac_supports_tpc().
For a AP vdev, hardcode ap_power_type as IEEE80211_REG_LPI_AP, which is
filled in the WMI_VDEV_SET_TPC_POWER_CMDID sent to the target.
Currently, LPI is the only supported AP power mode. Since there is
no method currently to set the AP power mode from user-space, the
power mode is hard-coded to LPI.
Retain the existing logic for populating the power mode for a station
vdev.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hariharan Basuthkar <quic_hbasuthk@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250606112316.39316-1-quic_hbasuthk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When both AP/STA and monitor interfaces are enabled, ieee80211_tx_status()
is invoked from two paths: the TX completion handler for data frames
and the WMI TX completion handler for management frames.
In the data path, the skb->cb is properly zeroed using memset, but in
the WMI path, this step is missing.
As a result, mac80211 encountered uninitialized (junk) values in
skb->cb when generating the radiotap header for monitor mode, leading
to invalid radiotap lengths.
Hence, explicitly zero the status field in the skb->cb using memset
in WMI TX completion path to ensure consistent and correct behavior
during WMI tx completion path.
Additionally, set info->status.rates[0].idx = -1 to indicate that
no valid rate information is available, avoiding misinterpretation of
garbage values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603063512.1887652-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when a station is associated with a Non-Transmitting BSS of an
MBSSID set, beacons are not frequently received from the firmware. This
results in missing events via beacons, such as channel switches, leading
to the station not switching to new channel as the AP does, eventually
causing a kick out event from the firmware. This issue arises due to
missing configuration of Non-Transmitting BSS information in station's
vdev up command.
Fix this by filling information such as the Transmitting BSSID, profile index
and profile count in vdev up command of station.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k station is unable to associate with non-transmitting BSSes
in a Multiple BSS set because the user-space does not receive
information about the non-transmitting BSSes from mac80211's
scan results.
The ath12k driver does not advertise its MBSSID capability to mac80211,
resulting in wiphy->support_mbssid not being set. Consequently, the
information about non-transmitting BSS is not parsed from received
Beacon/Probe response frames and is therefore not included in the
scan results.
Fix this by advertising the MBSSID capability of ath12k driver to
mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the ATH12K_DEFAULT_NOISE_FLOOR (-95) is used to calculate RSSI
value, providing an estimated noise floor value. Consequently, the RSSI
value is also approximate. This works but however, using actual noise floor
value will enable the reporting of the true RSSI value.
The firmware possesses the necessary data to determine the actual noise
floor. This data is provided to the host via the WMI event
WMI_PDEV_RSSI_DBM_CONVERSION_PARAMS_INFO_EVENTID, which includes the
runtime parameters needed for calculating the real noise floor in dBm. This
event is triggered by the firmware during channel changes, temperature
offset adjustments, and hardware chainmask modifications. The individual
TLVs may not always be present in each event. For instance, temperature
information might only appear if there is a change in offset due to
temperature variation.
Add support to handle and parse this WMI event. Use the received values to
calculate and store the noise floor value.
A subsequent change will use this noise floor value in the actual RSSI
calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623-support_real_noise_floor-v2-1-974bbafa317e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In a number of cases we see kernel panics on resume due
to ath11k kernel page fault, which happens under the
following circumstances:
1) First ath11k_hal_dump_srng_stats() call
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 22511ms before
ath11k_pci 0000:01:00.0: group_id 1 14440788ms before
[..]
ath11k_pci 0000:01:00.0: failed to receive control response completion, polling..
ath11k_pci 0000:01:00.0: Service connect timeout
ath11k_pci 0000:01:00.0: failed to connect to HTT: -110
ath11k_pci 0000:01:00.0: failed to start core: -110
ath11k_pci 0000:01:00.0: firmware crashed: MHI_CB_EE_RDDM
ath11k_pci 0000:01:00.0: already resetting count 2
ath11k_pci 0000:01:00.0: failed to wait wlan mode request (mode 4): -110
ath11k_pci 0000:01:00.0: qmi failed to send wlan mode off: -110
ath11k_pci 0000:01:00.0: failed to reconfigure driver on crash recovery
[..]
2) At this point reconfiguration fails (we have 2 resets) and
ath11k_core_reconfigure_on_crash() calls ath11k_hal_srng_deinit()
which destroys srng lists. However, it does not reset per-list
->initialized flag.
3) Second ath11k_hal_dump_srng_stats() call sees stale ->initialized
flag and attempts to dump srng stats:
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 66785ms before
ath11k_pci 0000:01:00.0: group_id 1 14485062ms before
ath11k_pci 0000:01:00.0: group_id 2 14485062ms before
ath11k_pci 0000:01:00.0: group_id 3 14485062ms before
ath11k_pci 0000:01:00.0: group_id 4 14780845ms before
ath11k_pci 0000:01:00.0: group_id 5 14780845ms before
ath11k_pci 0000:01:00.0: group_id 6 14485062ms before
ath11k_pci 0000:01:00.0: group_id 7 66814ms before
ath11k_pci 0000:01:00.0: group_id 8 68997ms before
ath11k_pci 0000:01:00.0: group_id 9 67588ms before
ath11k_pci 0000:01:00.0: group_id 10 69511ms before
BUG: unable to handle page fault for address: ffffa007404eb010
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 10022d067 PMD 100b01067 PTE 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k]
Call Trace:
<TASK>
? __die_body+0xae/0xb0
? page_fault_oops+0x381/0x3e0
? exc_page_fault+0x69/0xa0
? asm_exc_page_fault+0x22/0x30
? ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k (HASH:6cea 4)]
ath11k_qmi_driver_event_work+0xbd/0x1050 [ath11k (HASH:6cea 4)]
worker_thread+0x389/0x930
kthread+0x149/0x170
Clear per-list ->initialized flag in ath11k_hal_srng_deinit().
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 5118935b1b ("ath11k: dump SRNG stats during FW assert")
Link: https://patch.msgid.link/20250612084551.702803-1-senozhatsky@chromium.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce 'firmware-name' property to allow end-users and/or integrators to
decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and CPU
capability, or performance and power optimization for different application
scenarios.
Currently, there are two firmwares, both files can be executed
interchangeably.
For example:
- ath11k/WCN6855/hw2.0/amss.bin,
ath11k/WCN6855/hw2.0/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
- ath11k/WCN6855/hw2.0/nfa765/amss.bin,
ath11k/WCN6855/hw2.0/nfa765/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
The former is the default firmware, suitable for most WiFi 6 STA functions.
The latter adds support for commercial-quality SAP and optimizes power
consumption for IoT applications. And both use the same BDF/regdb data
within the main board-2.bin.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250522013444.1301330-3-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce 'firmware-name' property to allow end-users and/or integrators
to decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and
CPU capability, or performance and power optimization for different
application scenarios.
Two firmwares are supported: 'WCN6855/hw2.0' and 'WCN6855/hw2.0/nfa765'.
The former is the default firmware, suitable for most WiFi 6 STA
functions. The latter adds support for commercial-quality SAP and
optimizes power consumption for IoT applications.
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250522013444.1301330-2-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since 2b0996c764 , all of this platform code became no-op with no OF
replacement. Not only that, there are no users of AHB here. Add an OF
match table that mostly mirrors the original platform device id table.
Use a qca prefix as is done for the only other property: qca,no-eeprom.
Also used qca prefix for ar9530 as the latter seems to be a mistake.
This will be used to add ath9k support for the various ath79 devices
here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-5-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
fbnic_fw_clear_cmpl() does the inverse of fbnic_mbx_set_cmpl().
It removes the completion from the mailbox table.
It also calls fbnic_mbx_set_cmpl_slot() internally.
It should have fbnic_mbx prefix, not fbnic_fw.
I'm not very clear on what the distinction is between the two
prefixes but the matching "set" and "clear" functions should
use the same prefix.
While at it move the "clear" function closer to the "set".
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250624142834.3275164-6-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
