The Zynq UltraScale+ Devices Register Reference states that the WAKEUP
bit "should be set to 0 after the MCU sleep status bit gets back to 0."
If this is not done, the mcu is not going to sleep on reset and fail the
reset.
Set WAKEUP to 0 before triggering a reset to make sure that the reset is
successful.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cpb_size is given in kilobytes, but the bitrate is given in bits per
second. Therefore, the calculation of the initial removal delay and the
cpb size for the firmware were wrong.
Convert the bitrate to kilobytes before calculating the cpb size in 90
kHz units for sending it to the firmware. Also reuse the result for the
initial removal delay, to make it obvious that we are setting the
initial removal delay to the maximum value.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When creating a channel, freq_idr defines the number of frames between
IDR frames in the coded stream. In V4L2, the period between IDR frames
shall be taken from the GOP_SIZE control.
Set the IDR frame frequency equal to the GOP size and let every GOP
start with an IDR frame.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The subframe_latency and lda_control_mode fields directly follow
freq_golden_ref field and there is no unknown field in between. The
unknown field it at the end of the message.
Reorder the fields accordingly. This further allows to drop the hard
coded value from the lda_control_mode field and set the mode to 0.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The gop_length field is actually only u16 and there are two more u8
fields in the message:
- the number of consecutive b-frames
- frequency of golden frames
Fix the message and thus fix the configuration of the GOP length.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Only negative values are actual errors and positive values are used for
warnings. Warnings should not fail the encoding process.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The codec firmware uses error codes to report errors during the
configuration of a channel or while encoding a frame. Translate them
into human readable strings for debugging.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit cc62c74749 ("media: allegro: add missed checks in
allegro_open()") the allegro device does provide v4l2 controls to user
space anymore. The reason is that v4l2_fh_init() initializes
fh->ctrl_handler to vdev->ctrl_handler, which invalidates the previous
driver override of the ctrl_handler.
Therefore, v4l2_fh_init() must be called before the driver overrides the
fh->ctrl_handler with its own handler.
Move the initialization of the fh back to the top, as the initialization
does not does not need to be reverted on errors, but it is enough to
free the channel.
Fixes: cc62c74749 ("media: allegro: add missed checks in allegro_open()")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This argument refers to a stable name for an HDMI port, mostly i915
(ACPI) specific. Since we'll be introducing a more generic 'name' argument
as well later, rename this now to avoid confusion.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The new format is called V4L2_PIX_FMT_Y14. Like V4L2_PIX_FMT_Y10 and
V4L2_PIX_FMT_Y12 it is stored in two bytes per pixel but has only two
unused bits at the top.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver doesn't really support V4L2_PIX_FMT_Y16, as there's no 16-bit
greyscale media bus code defined by the kernel. It (ab)uses the format
to capture 10-bit and 12-bit greyscale formats. Fix it to properly
support MEDIA_BUS_FMT_Y10_1X10 and MEDIA_BUS_FMT_Y12_1X12 instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 4791bd7d6a ("media: imx: Try colorimetry at both sink and
source pads") reworked the way that formats are set on the sink pad of
the CSI subdevice, and accidentally removed video field handling.
Restore it by defaulting to V4L2_FIELD_NONE if the field value isn't
supported, with the only two supported value being V4L2_FIELD_NONE and
V4L2_FIELD_INTERLACED.
Fixes: 4791bd7d6a ("media: imx: Try colorimetry at both sink and source pads")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The imx7_csi_dma_reflash() function starts by reading the unrelated
register CSI_CSICR18 to then overwrite the read value with a read from
register CSI_CSICR3. This is likely due to a bad copy&paste, and is not
needed. Remove the extraneous read from register CSI_CSICR18.
Fixes: 9e5fa4e1e5 ("media: imx7-media-csi: Use u32 for storing register reads")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable filtering based on CSI-2 data type. Otherwise sources that send
multiple data types (such as sensors that send embedded data) will not
be properly supported. They will both result in additional non-image
lines being captured, and in the receiver being confused as it doesn't
resynchronise on vsync.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the RESOL_CH0 register to the list of registers printed through the
debugfs debug infrastructure for the driver, as it can be useful to
verify proper configuration of the CSI-2 receiver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The .s_stream() implementation incorrectly powers on the source when
stopping the stream. Power it off instead.
Fixes: 7807063b86 ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes: 659fefa0eb ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01")
Fixes: 59f8b0bf3c ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes: 8668d504d7 ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor")
Fixes: c0b33bdc5b ("[media] gspca-stv06xx: support bandwidth changing")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have at least one endpoint before accessing
the endpoint array to avoid dereferencing a NULL-pointer on stream
start.
Note that these sanity checks are not redundant as the driver is mixing
looking up altsettings by index and by number, which need not coincide.
Fixes: 1876bb923c ("V4L/DVB (12079): gspca_ov519: add support for the ov511 bridge")
Fixes: b282d87332 ("V4L/DVB (12080): gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This dprintk is supposed to be informational, not an error. Set it to
the same level as the other messages related to memory allocations so
the kernel log does not get filled by messages during normal operation.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 7cbeb2e1bf ("media: smiapp: Move definitions under driver
directory") moved the definitions in include/media/i2c/smiapp.h into other
files and removed include/media/i2c/smiapp.h.
Since then, ./scripts/get_maintainer.pl --self-test complains:
warning: no file matches F: include/media/i2c/smiapp.h
Remove MAINTAINER file entry to this removed file and while at it, update
Sakari's email address in this section.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, imgu is working on 450MHz for all cases, however
in some cases (input frame less than 2048x1152), the imgu
did not need work in high frequency.
This patch make imgu work on 200MHz if the imgu input
frame is less than 2048x1152 to save power.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.
Change this by brinting the register values hex formatted and the states
as more readable string.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.
Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use underlines to highlight optional and required properties. This is
quite common for all bindings. Align descriptions and start sentence
with uppercase letter. Also reword the usage of the required
endpoint properties for the output port in case BT.656 should be used.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.
This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.
Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
