The LED enumerators are missing, which prevents the LEDs from being
accurately told apart by label. Fill in the enumerators the same way
they are already present on PDK3.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Ethernet connection over GMAC controller connected to
the Micrel KSZ9031 Ethernet RGMII PHY located on the boards.
The mentioned GMAC controller is one of two network controllers
embedded on the NXP Automotive SoCs S32G2 and S32G3.
The supported boards:
* EVB: S32G-VNP-EVB with S32G2 SoC
* RDB2: S32G-VNP-RDB2
* RDB3: S32G-VNP-RDB3
Tested-by: Enric Balletbo i Serra <eballetb@redhat.com>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pwm node used by the backlight output pin BKL1_PWM and
reference it from the pwm-backlight node.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LPUART1 is not disabled, but used by system manager (SM) and should not
be used by Linux.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
66 MHz is the maximum FlexPI clock frequency in normal/overdrive mode
when RXCLKSRC = 0 (Default)
Fixes: 91d1ff322c ("arm64: dt: imx95: Add TQMa95xxSA")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX93 integrates an ADS7846 resistive touchscreen controller.
The controller is physically located on the SOM, and its signals are
routed to the SOM pins, allowing carrier boards to make use of it.
This patch adds the ADS7846 node and the appropriate SPI controller.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX93 can integrate the WM8904, a high-performance
ultra-low-power stereo codec optimized for portable audio applications.
This patch adds the WM8904 device to the appropriate I2C bus, enables
the SAI peripheral, and introduces the sound node to expose the
sound card to the system.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX93 features Dual Freescale/NXP PCA9541 chip as a Power
Management Integrated circuit (PMIC).
The PMIC is programmable via the I2C interface and its associated
register map, and this patch adds its support.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree nodes for the WiFi and Bluetooth module mounted on the
VAR-SOM-MX93. The module can be based on either the NXP IW612 or IW611
chipset, depending on the configuration chosen by the customer.
Regardless of the chipset used, WiFi communicates over SDIO and Bluetooth
over UART.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the lpuart1 dts node to support the PCIE9098 bluetooth on M.2
connector.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add phandle to the OCOTP mac-address nodes so the FEC can obtain a fixed
MAC address specific to each board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
default, state_100mhz and state_200mhz use the same settings. But current
driver use these to indicate if sd3.0 support.
Add SD gpio pin group (Reset, CD, WP) for usdhc2.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign double SD bus frequency to support SDR104 mode, where the operating
clock runs at 208 MHz.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
default, state_100mhz and state_200mhz use the same settings. But current
driver use these to indicate if sd3.0 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add overlay to support PWM fan on the phyBOARD-Nash-i.MX93 board. Fan
can be connected to the FAN (X48) connector on the board and will be
controlled according to the following CPU temperature trips table:
- bellow 50 degrees - fan is off (<1% duty cycle)
- between 50 and 58 degrees - low fan speed (~35% duty cycle)
- between 58 and 65 degrees - fan medium speed (~60% duty cycle)
- above 65 degrees - fan at full speed (>99% duty cycle)
The output frequency of PWM signal is set to 25 kHz.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Alberto Merciai <alb3rt0.m3rciai@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable internal pull up of the active low audio codec reset pin.
Otherwise the audio codec does not reset properly and is not working.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for powertip,ph128800t006-zhc01 connected via peb-av-10
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PEB-AV-10 board can be used with different displays or in audio-only
mode.
Split the device tree overlays to reflect these use cases. To use the
board with the EDT ETML1010G3DRA display, the overlay
imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtbo must now be used
instead of imx8mm-phyboard-polis-peb-av-10.dtbo.
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
sn65dsi83 is mounted on som. Add the static configuration there.
So it can be used by other boards too.
Use mipi_dsi_out from imx8mm.dtsi directly.
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
