Disable bit 29 of SCLKGATE_DIS register around pps sequence
when we turn panel power on.
--v2
-Squash two commit together [Jani]
-Use IS_DISPLAY_VER [Jani]
-Fix multiline comment [Jani]
--v3
-Define register in a more appropriate place [Mitul]
--v4
-Register is already defined no need to define it again [Ville]
-Use correct WA number (lineage no.) [Dnyaneshwar]
-Fix the range on which this WA is applied [Dnyaneshwar]
Bspec: 49304
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813042807.4015214-1-suraj.kandpal@intel.com
We are checking cp_irq_count from the wrong hdcp structure which
ends up giving timed out errors. We only increment the cp_irq_count
of the primary connector's hdcp structure but here in case of
multidisplay setup we end up checking the secondary connector's hdcp
structure, which will not have its cp_irq_count incremented. This leads
to a timed out at CP_IRQ error even though a CP_IRQ was raised. Extract
it from the correct intel_hdcp structure.
--v2
-Explain why it was the wrong hdcp structure [Jani]
Fixes: 8c9e4f68b8 ("drm/i915/hdcp: Use per-device debugs")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240809114127.3940699-2-suraj.kandpal@intel.com
Sync with v6.11-rc1 in general, and specifically get the new
BACKLIGHT_POWER_ constants for power states.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As explained in the previous patch, the MST link BW reported by branch
devices during topology probing/path resources enumeration depends on
the link parameters programmed to DPCD to be up-to-date. After a sink is
plugged this is not ensured, as those DPCD values start out zeroed. The
target link parameters (for a subsequent modeset) are the maximum that
is supported, so make sure these maximum values are programmed before the
topology probing.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-14-imre.deak@intel.com
The MST link BW reported by branch devices via the ENUM_PATH_RESOURCES
message depends on the channel coding and link rate/lane count
parameters programmed to DPCD. This is the case at least for some branch
devices, while for others the reported BW is independent of the link
parameters. In any case the DP standard requires the branch device to
adjust the returned value to both account for the different way the BW
for FEC is accounted for (included in the returned value for non-UHBR
and not included for UHBR rates) and to limit the returned value to the
(trained) link BW between the source and first downstream branch
device, see DP v2.0/v2.1 Figure 2-94, DP v2.1 5.9.7. Presumedly this is
also the reason why the standard requires the DPCD link rate/lane count
values being up-to-date before sending the ENUM_PATH_RESOURCES message,
see DP v2.1 2.14.9.4.
Based on the above reprobe the MST topology after the link is retrained
with new link parameters to make sure that the MST link BW tracked in
the MST topology state (via each topology port's full_pbn value) is
up-to-date.
The next patch will make sure that the MST link BW is also kept
up-to-date if the link is disabled.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-13-imre.deak@intel.com
On MST links - at least for some MST branch devices - the list of modes
returned to users on an enabled link depends on the current link
rate/lane count parameters (besides the DPRX link capabilities, any MST
branch BW limit and the maximum link parameters reduced after LT
failures). In particular the MST branch BW limit may depend on the link
rate/lane count parameters programmed to DPCD. After an LT failure and
limiting the maximum link parameters accordingly, users should see a
mode list reflecting these new limits. However with the current fallback
order this isn't ensured, as the new limit could allow for modes
requiring a higher link BW, but these modes will be filtered out due to
the enabled link's lower link BW.
Ensure that the mode list changes in a consistent way after a link
training failure and reducing the link parameters by changing the
fallback order on MST links to happen in BW order.
v2:
- s/INTEL_DP_MAX_SUPPORTED_LANE_COUNTS/INTEL_DP_MAX_SUPPORTED_LANE_CONFIGS
and s/num_common_lane_counts/num_common_lane_configs to make the
difference wrt. max lane counts clearer. (Suraj)
- Add a TODO comment to make the SST fallback logic work the same way as
MST. (Arun)
- Use sort_r()'s default swap function instead of a custom one.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729144458.2763667-1-imre.deak@intel.com
There are multiple failure cases a modeset-retry uevent can be sent for
a link (TBT tunnel BW allocation failure, unrecoverable link training
failure), a follow-up patch adding the handling for a new case where the
DP MST payload allocation fails. The uevent is the same in all cases,
sent to all the connectors on the link, so in case of multiple failures
there is no point in sending a separate uevent for each failure; prevent
this, sending only a single modeset-retry uevent for a commit.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-7-imre.deak@intel.com
Initialize the DP link parameters during HW readout. These need to be
up-to-date at least for the MST topology probing, which depends on the
link rate and lane count programmed in DPCD. A follow-up patch will
program the DPCD values to reflect the maximum link parameters before
the first MST topology probing, but should do so only if the link is
disabled (link_trained==false).
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-6-imre.deak@intel.com
In the
if (old_ddps != port->ddps || !created)
if (port->ddps && !port->input)
ret = drm_dp_send_enum_path_resources();
sequence the first if's condition is true if the port exists already
(!created) or the port was created anew (hence old_ddps==0) and it was
in the plugged state (port->ddps==1). The second if's condition is true
for output ports in the plugged state. So the function is called for an
output port in the plugged state, regardless if it already existed or
not and regardless of the old plugged state. In all other cases
port->full_pbn can be zeroed as the port is either an input for which
full_pbn is never set, or an output in the unplugged state for which
full_pbn was already zeroed previously or the port was just created
(with port->full_pbn==0).
Simplify the condition, making it clear that the path resources are
always enumerated for an output port in the plugged state.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-4-imre.deak@intel.com
On the off chance that clock value ends up being too high (by means
of skl_ddi_calculate_wrpll() having been called with big enough
value of crtc_state->port_clock * 1000), one possible consequence
may be that the result will not be able to fit into signed int.
Fix this issue by moving conversion of clock parameter from kHz to Hz
into the body of skl_ddi_calculate_wrpll(), as well as casting the
same parameter to u64 type while calculating the value for AFE clock.
This both mitigates the overflow problem and avoids possible erroneous
integer promotion mishaps.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 82d3543701 ("drm/i915/skl: Implementation of SKL DPLL programming")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729174035.25727-1-n.zhandarovich@fintech.ru
