Radxa Compute Module 3(CM3) is one of the modules from a series
System On Module based on the Radxa ROCK 3 series and is compatible
with Raspberry Pi CM4 pinout and form factor.
Specification:
- Rockchip RK3566
- up to 8GB LPDDR4
- up to 128GB high performance eMMC
- Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless,
BT 5.0, BLE with onboard and external antenna.
- Gigabit Ethernet PHY
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Since Radxa CM3 is compatible with Raspberry Pi CM4 pinout so it is
possible to mount Radxa CM3 on top of the Rasberry Pi CM4 IO board.
Add support for Radxa CM3.
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230112105902.192852-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa Compute Module 3(CM3) is one of the modules from a series
System On Module based on the Radxa ROCK 3 series and is compatible
with Raspberry Pi CM4 in pinout and form factor.
Specification:
- Rockchip RK3566
- up to 8GB LPDDR4
- up to 128GB high performance eMMC
- Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless,
BT 5.0, BLE with onboard and external antenna.
- Gigabit Ethernet PHY
Add dt-bindings for Radxa CM3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230112105902.192852-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230110134658.820691-3-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neu6 needs to mount on top of associated Edgeble IO boards for
creating complete platform solutions.
Enable eMMC for now to boot Linux successfully.
Add support for Edgeble Neu6 Model A SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230110134658.820691-2-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update the blue LED to be controlled via pwm to enable control of LED
brightness. Add red LED as a GPIO controlled LED. The documentation
stated "label" was depreciated so function and color was used instead.
The LED names (led-2 and led-3) are given because that is what they
are numbered on the board itself; LED 1 is wired directly into an
always on regulator and is not controllable. LED 2 is labelled "alive"
on the board and documentation recommends we set the function as
status over other miscellaneous functions. LED 3 is labelled "chg" on
the board.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20221201203655.1245-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Without the trips, the following errors are received in the dmesg
log and the rockchip-thermal driver fails to load the gpu sensor:
"thermal_sys: Failed to find 'trips' node"
"rockchip-thermal ff280000.tsadc: failed to register sensor 1: -22"
Trip values are assumed, unfortunately, as the same values as the
CPU. The datasheet and TRM didn't appear to have any information
regarding thermals for the GPU.
Stress tested successfully on my Odroid Go Advance.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20221201203655.1245-4-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Odroid Go Advance devicetree tries to set the rate for the cpll
clock to 17MHz, which is not a supported rate. This fails, and triggers
the error of "clk: couldn't set cpll clk rate to 17000000 (-22),
current rate: 17000000" in the dmesg log. Remove the incorrect rate.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20221201203655.1245-3-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change the audio card name for the Odroid Go Advance series to
rk817_int. This matches the audio card name of the Anbernic RG353V.
This is done to provide a consistent card name so that a single ALSA
UCM file can be used for all (identical) implementations of this codec
and configuration combo. The rk817_int configuration is for when the
internal speaker amplifier of the rk817 is used. The other Anbernic
devices have the name as rk817_ext for when an external speaker
amplifier is used.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20221201203655.1245-2-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20221203074149.11543-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
LubanCat 2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20230108110817.2214859-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds simple audio card nodes
Enabled i2s0_8ch as it is needed for hdmi audio
Added i2s1_8ch as it is needed for 3.5mm audio jack and limit it to a
single-channel, as i2s1m0_sdo{1,2,3} and i2s1m0_sdi{1,2,3} are used
by pcie.
Signed-off-by: Furkan Kardame <f.kardame@manjaro.org>
Link: https://lore.kernel.org/r/20230109203232.45192-1-f.kardame@manjaro.org
[dropped the duplicate i2s@fe410000 node]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The LubanCat 1 is a RK3566 based SBC, developed by Dongguan EmbedFire
Electronic Technology Co., Ltd.
It has the following characteristics:
- MicroSD card slot, onboard eMMC flash memory
- 1GbE Realtek RTL8211F Ethernet Transceiver
- 1 USB Type-C port (power and USB2.0 OTG)
- 1 USB 3.0 Host port
- 3 USB 2.0 Host ports
- 1 HDMI
- 1 infrared receiver
- 1 MIPI DSI
- 1 MIPI CSI
- 1 x 4-section headphone jack
- Mini PCIe socket (USB or PCIe)
- 1 SIM Card slot
- 1 SYS LED and 1 PWR LED
- 40-pin GPIO expansion header
Signed-off-by: Wenhao Cui <lasstp5011@gmail.com>
Signed-off-by: Yuteng Zhong <zonyitoo@gmail.com>
Link: https://lore.kernel.org/r/Y6UdjhBD/Xa7ALya@VM-66-53-centos
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20221209102524.129367-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull spi fix from Mark Brown:
"One driver specific change here which handles the case where a SPI
device for some reason tries to change the bus speed during a message
on fsl_spi hardware, this should be very unusual"
* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fsl_spi: Don't change speed while chipselect is active
Pull regulator fixes from Mark Brown:
"Two core fixes here, one for a long standing race which some Qualcomm
systems have started triggering with their UFS driver and another
fixing a problem with supply lookup introduced by the fixes for devm
related use after free issues that were introduced in this merge
window"
* tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: fix deadlock on regulator enable
regulator: core: Fix resolve supply lookup issue
Pull coccicheck update from Julia Lawall:
"Modernize use of grep in coccicheck:
Use 'grep -E' instead of 'egrep'"
* tag 'coccinelle-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccicheck: use "grep -E" instead of "egrep"
Pull kernel hardening fixes from Kees Cook:
- Fix CFI failure with KASAN (Sami Tolvanen)
- Fix LKDTM + CFI under GCC 7 and 8 (Kristina Martsenko)
- Limit CONFIG_ZERO_CALL_USED_REGS to Clang > 15.0.6 (Nathan
Chancellor)
- Ignore "contents" argument in LoadPin's LSM hook handling
- Fix paste-o in /sys/kernel/warn_count API docs
- Use READ_ONCE() consistently for oops/warn limit reading
* tag 'hardening-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
cfi: Fix CFI failure with KASAN
exit: Use READ_ONCE() for all oops/warn limit reads
security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
lkdtm: cfi: Make PAC test work with GCC 7 and 8
docs: Fix path paste-o for /sys/kernel/warn_count
LoadPin: Ignore the "contents" argument of the LSM hooks
Pull dma-mapping fixes from Christoph Hellwig:
"Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
allocator, as it copes with that just as badly as the coherent
allocator, and then add a check to make sure no one passes the flag
ever again"
* tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reject GFP_COMP for noncoherent allocations
ALSA: memalloc: don't use GFP_COMP for non-coherent dma allocations
Pull 9p updates from Dominique Martinet:
- improve p9_check_errors to check buffer size instead of msize when
possible (e.g. not zero-copy)
- some more syzbot and KCSAN fixes
- minor headers include cleanup
* tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux:
9p/client: fix data race on req->status
net/9p: fix response size check in p9_check_errors()
net/9p: distinguish zero-copy requests
9p/xen: do not memcpy header into req->rc
9p: set req refcount to zero to avoid uninitialized usage
9p/net: Remove unneeded idr.h #include
9p/fs: Remove unneeded idr.h #include
