Document the device tree bindings for the Renesas RZ/V2H(P) SoC
Clock Pulse Generator (CPG).
CPG block handles the below operations:
- Generation and control of clock signals for the IP modules
- Generation and control of resets
- Control over booting
- Low power consumption and power supply domains
Also define constants for the core clocks of the RZ/V2H(P) SoC. Note the
core clocks are a subset of the ones which are listed as part of section
4.4.2 of HW manual Rev.1.01 which cannot be controlled by CLKON register.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240729202645.263525-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently, all PLLs but PLL2 are modelled as fixed divider clocks, based
on the state of the mode pins. However, the boot loader stack may have
changed the actual PLL configuration from the default, leading to
incorrect clock frequencies.
Describe PLL1 as a fixed fractional PLL instead, and PLL2, PLL3, PLL4,
and PLL6 as variable fractional PLLs.
Reformat nearby lines to retain a consistent layout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/b98523ed08de7386944c5ae860eae107dc28be3e.1721648548.git.geert+renesas@glider.be
Currently, all PLLs are modelled as fixed divider clocks, based on the
state of the mode pins. However, the boot loader stack may have changed
the actual PLL configuration from the default, leading to incorrect
clock frequencies.
Describe PLL1 as a fixed fractional PLL instead, and PLL2, PLL3, and
PLL6 as variable fractional PLLs. Note that the R-Car Gen4 clock driver
does not support variable 9.24 PLLs yet, so the driver will downgrade
them to fixed fractional PLLs, too.
Reformat nearby lines to retain a consistent layout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/8544571f507e00ed6fc61617d27c9e19de5e9d11.1721648548.git.geert+renesas@glider.be
The custom clock driver that models the PLL clocks on R-Car Gen4
supports only fractional 8.25 PLLs, as used on R-Car V4H/V4M.
R-Car S4-8 uses integer and fractional multiplication fields that are
one bit larger resp. smaller, and a slightly different formula.
Extend the existing support to fractional 9.24 PLL, and introduce new
clock types and helper macros to describe these PLLs.
Note that there is no use case for variable fractional 9.24 PLLs yet, as
the Cortex-A55 cores on R-Car S4-8 do not support High Performance mode.
Hence the PLL is always modeled as a fixed PLL, regardless of the
description,
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/5684eda1260435c8eceabc274e0b18cb280a6341.1721648548.git.geert+renesas@glider.be
R-Car Gen4 PLLs support fractional multiplication, which can improve
accuracy when configuring a specific frequency.
Add support for fractional multiplication to the custom clock driver
for PLLs, which is currently used only for PLL2 on R-Car V4H.
While at it, add the missing blank line after the function.
Note that Fractional Multiplication is not enabled by the driver,
but used only if the boot loaded enabled it before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/1a58ebef6f54460f49fb81ba9bbf288164de2646.1721648548.git.geert+renesas@glider.be
The custom clock driver that models the PLL clocks on R-Car Gen4 assumes
the integer and fractional[*] multiplication field sizes as used on
R-Car V4H and V4M, representing a fractional 8.25 number.
Rename the related definitions, functions, and structures to clarify
this, and to prepare for the advent of support for the different field
sizes on R-Car S4-8.
[*] The fractional part is not yet supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/2ce9f9c75bfb6312129d416672f9691bbd11c0e7.1721648548.git.geert+renesas@glider.be
Pull Kbuild fixes from Masahiro Yamada:
- Fix RPM package build error caused by an incorrect locale setup
- Mark modules.weakdep as ghost in RPM package
- Fix the odd combination of -S and -c in stack protector scripts,
which is an error with the latest Clang
* tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Fix '-S -c' in x86 stack protector scripts
kbuild: rpm-pkg: ghost modules.weakdep file
kbuild: rpm-pkg: Fix C locale setup
This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.
That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3a7e02c040 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull UBI and UBIFS updates from Richard Weinberger:
- Many fixes for power-cut issues by Zhihao Cheng
- Another ubiblock error path fix
- ubiblock section mismatch fix
- Misc fixes all over the place
* tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Fix ubi_init() ubiblock_exit() section mismatch
ubifs: add check for crypto_shash_tfm_digest
ubifs: Fix inconsistent inode size when powercut happens during appendant writing
ubi: block: fix null-pointer-dereference in ubiblock_create()
ubifs: fix kernel-doc warnings
ubifs: correct UBIFS_DFS_DIR_LEN macro definition and improve code clarity
mtd: ubi: Restore missing cleanup on ubi_init() failure path
ubifs: dbg_orphan_check: Fix missed key type checking
ubifs: Fix unattached inode when powercut happens in creating
ubifs: Fix space leak when powercut happens in linking tmpfile
ubifs: Move ui->data initialization after initializing security
ubifs: Fix adding orphan entry twice for the same inode
ubifs: Remove insert_dead_orphan from replaying orphan process
Revert "ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path"
ubifs: Don't add xattr inode into orphan area
ubifs: Fix unattached xattr inode if powercut happens after deleting
mtd: ubi: avoid expensive do_div() on 32-bit machines
mtd: ubi: make ubi_class constant
ubi: eba: properly rollback inside self_check_eba
After a recent change in clang to stop consuming all instances of '-S'
and '-c' [1], the stack protector scripts break due to the kernel's use
of -Werror=unused-command-line-argument to catch cases where flags are
not being properly consumed by the compiler driver:
$ echo | clang -o - -x c - -S -c -Werror=unused-command-line-argument
clang: error: argument unused during compilation: '-c' [-Werror,-Wunused-command-line-argument]
This results in CONFIG_STACKPROTECTOR getting disabled because
CONFIG_CC_HAS_SANE_STACKPROTECTOR is no longer set.
'-c' and '-S' both instruct the compiler to stop at different stages of
the pipeline ('-S' after compiling, '-c' after assembling), so having
them present together in the same command makes little sense. In this
case, the test wants to stop before assembling because it is looking at
the textual assembly output of the compiler for either '%fs' or '%gs',
so remove '-c' from the list of arguments to resolve the error.
All versions of GCC continue to work after this change, along with
versions of clang that do or do not contain the change mentioned above.
Cc: stable@vger.kernel.org
Fixes: 4f7fd4d7a7 ("[PATCH] Add the -fstack-protector option to the CFLAGS")
Fixes: 60a5317ff0 ("x86: implement x86_32 stack protector")
Link: 6461e53781 [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull turbostat updates from Len Brown:
- Enable turbostat extensions to add both perf and PMT (Intel
Platform Monitoring Technology) counters via the cmdline
- Demonstrate PMT access with built-in support for Meteor Lake's
Die C6 counter
* tag 'v6.11-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2024.07.26
tools/power turbostat: Include umask=%x in perf counter's config
tools/power turbostat: Document PMT in turbostat.8
tools/power turbostat: Add MTL's PMT DC6 builtin counter
tools/power turbostat: Add early support for PMT counters
tools/power turbostat: Add selftests for added perf counters
tools/power turbostat: Add selftests for SMI, APERF and MPERF counters
tools/power turbostat: Move verbose counter messages to level 2
tools/power turbostat: Move debug prints from stdout to stderr
tools/power turbostat: Fix typo in turbostat.8
tools/power turbostat: Add perf added counter example to turbostat.8
tools/power turbostat: Fix formatting in turbostat.8
tools/power turbostat: Extend --add option with perf counters
tools/power turbostat: Group SMI counter with APERF and MPERF
tools/power turbostat: Add ZERO_ARRAY for zero initializing builtin array
tools/power turbostat: Replace enum rapl_source and cstate_source with counter_source
tools/power turbostat: Remove anonymous union from rapl_counter_info_t
tools/power/turbostat: Switch to new Intel CPU model defines
Pull CXL updates from Dave Jiang:
"Core:
- A CXL maturity map has been added to the documentation to detail
the current state of CXL enabling.
It provides the status of the current state of various CXL features
to inform current and future contributors of where things are and
which areas need contribution.
- A notifier handler has been added in order for a newly created CXL
memory region to trigger the abstract distance metrics calculation.
This should bring parity for CXL memory to the same level vs
hotplugged DRAM for NUMA abstract distance calculation. The
abstract distance reflects relative performance used for memory
tiering handling.
- An addition for XOR math has been added to address the CXL DPA to
SPA translation.
CXL address translation did not support address interleave math
with XOR prior to this change.
Fixes:
- Fix to address race condition in the CXL memory hotplug notifier
- Add missing MODULE_DESCRIPTION() for CXL modules
- Fix incorrect vendor debug UUID define
Misc:
- A warning has been added to inform users of an unsupported
configuration when mixing CXL VH and RCH/RCD hierarchies
- The ENXIO error code has been replaced with EBUSY for inject poison
limit reached via debugfs and cxl-test support
- Moving the PCI config read in cxl_dvsec_rr_decode() to avoid
unnecessary PCI config reads
- A refactor to a common struct for DRAM and general media CXL
events"
* tag 'cxl-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/core/pci: Move reading of control register to immediately before usage
cxl: Remove defunct code calculating host bridge target positions
cxl/region: Verify target positions using the ordered target list
cxl: Restore XOR'd position bits during address translation
cxl/core: Fold cxl_trace_hpa() into cxl_dpa_to_hpa()
cxl/test: Replace ENXIO with EBUSY for inject poison limit reached
cxl/memdev: Replace ENXIO with EBUSY for inject poison limit reached
cxl/acpi: Warn on mixed CXL VH and RCH/RCD Hierarchy
cxl/core: Fix incorrect vendor debug UUID define
Documentation: CXL Maturity Map
cxl/region: Simplify cxl_region_nid()
cxl/region: Support to calculate memory tier abstract distance
cxl/region: Fix a race condition in memory hotplug notifier
cxl: add missing MODULE_DESCRIPTION() macros
cxl/events: Use a common struct for DRAM and General Media events
Pull unicode update from Gabriel Krisman Bertazi:
"Two small fixes to silence the compiler and static analyzers tools
from Ben Dooks and Jeff Johnson"
* tag 'unicode-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krisman/unicode:
unicode: add MODULE_DESCRIPTION() macros
unicode: make utf8 test count static
In the same way as for other similar files, mark as ghost the new file
generated by depmod for configured weak dependencies for modules,
modules.weakdep, so that although it is not included in the package,
claim the ownership on it.
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull more smb client updates from Steve French:
- fix for potential null pointer use in init cifs
- additional dynamic trace points to improve debugging of some common
scenarios
- two SMB1 fixes (one addressing reconnect with POSIX extensions, one a
mount parsing error)
* tag '6.11-rc-smb-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: add dynamic trace point for session setup key expired failures
smb3: add four dynamic tracepoints for copy_file_range and reflink
smb3: add dynamic tracepoint for reflink errors
cifs: mount with "unix" mount option for SMB1 incorrectly handled
cifs: fix reconnect with SMB1 UNIX Extensions
cifs: fix potential null pointer use in destroy_workqueue in init_cifs error path
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fix request without payloads cleanup (Leon)
- Use new protection information format (Francis)
- Improved debug message for lost pci link (Bart)
- Another apst quirk (Wang)
- Use appropriate sysfs api for printing chars (Markus)
- ublk async device deletion fix (Ming)
- drbd kerneldoc fixups (Simon)
- Fix deadlock between sd removal and release (Yang)
* tag 'block-6.11-20240726' of git://git.kernel.dk/linux:
nvme-pci: add missing condition check for existence of mapped data
ublk: fix UBLK_CMD_DEL_DEV_ASYNC handling
block: fix deadlock between sd_remove & sd_release
drbd: Add peer_device to Kernel doc
nvme-core: choose PIF from QPIF if QPIFS supports and PIF is QTYPE
nvme-pci: Fix the instructions for disabling power management
nvme: remove redundant bdev local variable
nvme-fabrics: Use seq_putc() in __nvmf_concat_opt_tokens()
nvme/pci: Add APST quirk for Lenovo N60z laptop
Pull io_uring fixes from Jens Axboe:
- Fix a syzbot issue for the msg ring cache added in this release. No
ill effects from this one, but it did make KMSAN unhappy (me)
- Sanitize the NAPI timeout handling, by unifying the value handling
into all ktime_t rather than converting back and forth (Pavel)
- Fail NAPI registration for IOPOLL rings, it's not supported (Pavel)
- Fix a theoretical issue with ring polling and cancelations (Pavel)
- Various little cleanups and fixes (Pavel)
* tag 'io_uring-6.11-20240726' of git://git.kernel.dk/linux:
io_uring/napi: pass ktime to io_napi_adjust_timeout
io_uring/napi: use ktime in busy polling
io_uring/msg_ring: fix uninitialized use of target_req->flags
io_uring: align iowq and task request error handling
io_uring: kill REQ_F_CANCEL_SEQ
io_uring: simplify io_uring_cmd return
io_uring: fix io_match_task must_hold
io_uring: don't allow netpolling with SETUP_IOPOLL
io_uring: tighten task exit cancellations
Pull vfs fixes from Christian Brauner:
"This contains two fixes for this merge window:
VFS:
- I noticed that it is possible for a privileged user to mount most
filesystems with a non-initial user namespace in sb->s_user_ns.
When fsopen() is called in a non-init namespace the caller's
namespace is recorded in fs_context->user_ns. If the returned file
descriptor is then passed to a process privileged in init_user_ns,
that process can call fsconfig(fd_fs, FSCONFIG_CMD_CREATE*),
creating a new superblock with sb->s_user_ns set to the namespace
of the process which called fsopen().
This is problematic as only filesystems that raise FS_USERNS_MOUNT
are known to be able to support a non-initial s_user_ns. Others may
suffer security issues, on-disk corruption or outright crash the
kernel. Prevent that by restricting such delegation to filesystems
that allow FS_USERNS_MOUNT.
Note, that this delegation requires a privileged process to
actually create the superblock so either the privileged process is
cooperaing or someone must have tricked a privileged process into
operating on a fscontext file descriptor whose origin it doesn't
know (a stupid idea).
The bug dates back to about 5 years afaict.
Misc:
- Fix hostfs parsing when the mount request comes in via the legacy
mount api.
In the legacy mount api hostfs allows to specify the host directory
mount without any key.
Restore that behavior"
* tag 'vfs-6.11-rc1.fixes.3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
hostfs: fix the host directory parse when mounting.
fs: don't allow non-init s_user_ns for filesystems without FS_USERNS_MOUNT
Pull Rust updates from Miguel Ojeda:
"The highlight is the establishment of a minimum version for the Rust
toolchain, including 'rustc' (and bundled tools) and 'bindgen'.
The initial minimum will be the pinned version we currently have, i.e.
we are just widening the allowed versions. That covers three stable
Rust releases: 1.78.0, 1.79.0, 1.80.0 (getting released tomorrow),
plus beta, plus nightly.
This should already be enough for kernel developers in distributions
that provide recent Rust compiler versions routinely, such as Arch
Linux, Debian Unstable (outside the freeze period), Fedora Linux,
Gentoo Linux (especially the testing channel), Nix (unstable) and
openSUSE Slowroll and Tumbleweed.
In addition, the kernel is now being built-tested by Rust's pre-merge
CI. That is, every change that is attempting to land into the Rust
compiler is tested against the kernel, and it is merged only if it
passes. Similarly, the bindgen tool has agreed to build the kernel in
their CI too.
Thus, with the pre-merge CI in place, both projects hope to avoid
unintentional changes to Rust that break the kernel. This means that,
in general, apart from intentional changes on their side (that we will
need to workaround conditionally on our side), the upcoming Rust
compiler versions should generally work.
In addition, the Rust project has proposed getting the kernel into
stable Rust (at least solving the main blockers) as one of its three
flagship goals for 2024H2 [1].
I would like to thank Niko, Sid, Emilio et al. for their help
promoting the collaboration between Rust and the kernel.
Toolchain and infrastructure:
- Support several Rust toolchain versions.
- Support several bindgen versions.
- Remove 'cargo' requirement and simplify 'rusttest', thanks to
'alloc' having been dropped last cycle.
- Provide proper error reporting for the 'rust-analyzer' target.
'kernel' crate:
- Add 'uaccess' module with a safe userspace pointers abstraction.
- Add 'page' module with a 'struct page' abstraction.
- Support more complex generics in workqueue's 'impl_has_work!'
macro.
'macros' crate:
- Add 'firmware' field support to the 'module!' macro.
- Improve 'module!' macro documentation.
Documentation:
- Provide instructions on what packages should be installed to build
the kernel in some popular Linux distributions.
- Introduce the new kernel.org LLVM+Rust toolchains.
- Explain '#[no_std]'.
And a few other small bits"
Link: https://rust-lang.github.io/rust-project-goals/2024h2/index.html#flagship-goals [1]
* tag 'rust-6.11' of https://github.com/Rust-for-Linux/linux: (26 commits)
docs: rust: quick-start: add section on Linux distributions
rust: warn about `bindgen` versions 0.66.0 and 0.66.1
rust: start supporting several `bindgen` versions
rust: work around `bindgen` 0.69.0 issue
rust: avoid assuming a particular `bindgen` build
rust: start supporting several compiler versions
rust: simplify Clippy warning flags set
rust: relax most deny-level lints to warnings
rust: allow `dead_code` for never constructed bindings
rust: init: simplify from `map_err` to `inspect_err`
rust: macros: indent list item in `paste!`'s docs
rust: add abstraction for `struct page`
rust: uaccess: add typed accessors for userspace pointers
uaccess: always export _copy_[from|to]_user with CONFIG_RUST
rust: uaccess: add userspace pointers
kbuild: rust-analyzer: improve comment documentation
kbuild: rust-analyzer: better error handling
docs: rust: no_std is used
rust: alloc: add __GFP_HIGHMEM flag
rust: alloc: fix typo in docs for GFP_NOWAIT
...
Pull apparmor updates from John Johansen:
"Cleanups
- optimization: try to avoid refing the label in apparmor_file_open
- remove useless static inline function is_deleted
- use kvfree_sensitive to free data->data
- fix typo in kernel doc
Bug fixes:
- unpack transition table if dfa is not present
- test: add MODULE_DESCRIPTION()
- take nosymfollow flag into account
- fix possible NULL pointer dereference
- fix null pointer deref when receiving skb during sock creation"
* tag 'apparmor-pr-2024-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: unpack transition table if dfa is not present
apparmor: try to avoid refing the label in apparmor_file_open
apparmor: test: add MODULE_DESCRIPTION()
apparmor: take nosymfollow flag into account
apparmor: fix possible NULL pointer dereference
apparmor: fix typo in kernel doc
apparmor: remove useless static inline function is_deleted
apparmor: use kvfree_sensitive to free data->data
apparmor: Fix null pointer deref when receiving skb during sock creation
