Monaco EVK is a single board computer, based on the Qualcomm
QCS8300 SoC, with the following features :
- Storage: 1 × 128 GB UFS, micro-SD card, EEPROMs for MACs,
and eMMC.
- Audio/Video, Camera & Display ports.
- Connectivity: RJ45 2.5GbE, WLAN/Bluetooth, CAN/CAN-FD.
- PCIe ports.
- USB & UART ports.
On top of Monaco EVK board additional mezzanine boards can be
stacked in future.
Add support for the following components :
- GPI (Generic Peripheral Interface) and QUPv3-0/1
controllers to facilitate DMA and peripheral communication.
- TCA9534 I/O expander via I2C to provide 8 additional GPIO
lines for extended I/O functionality.
- USB1 controller in device mode to support USB peripheral
operations. USB OTG mode will be enabled for USB1 controller
once the VBUS control based on ID pin is implemented in
hd3ss3220.c.
- Remoteproc subsystems for supported DSPs such as Audio DSP,
Compute DSP and Generic DSP, along with their corresponding
firmware.
- Configure nvmem-layout on the I2C EEPROM to store data for Ethernet
and other consumers.
- QCA8081 2.5G Ethernet PHY on port-0 and expose the
Ethernet MAC address via nvmem for network configuration.
It depends on CONFIG_QCA808X_PHY to use QCA8081 PHY.
- Support for the Iris video codec.
Written with inputs from :
Rakesh Kota <rakesh.kota@oss.qualcomm.com> - Regulators.
Nirmesh Kumar Singh <nirmesh.Singh@oss.qualcomm.com> - GPIO expander.
Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com> - GPI/QUP.
Mohd Ayaan Anwar <quic_mohdayaa@quicinc.com> - Ethernet.
Monish Chunara <quic_mchunara@quicinc.com> - EEPROM.
Vikash Garodia <quic_vgarodia@quicinc.com> - Iris Video codec.
Swati Agarwal <swati.agarwal@oss.qualcomm.com> - USB.
Signed-off-by: Umang Chheda <umang.chheda@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250905192350.1223812-3-umang.chheda@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce qcs6490-audioreach.dtsi to support AudioReach architecture on
QCS6490 platforms. The existing ADSP Bypass DTSI files such as sc7280.dtsi,
which is tailored for ADSP Bypass architecture as they lack DSP-specific
nodes required for AudioReach. The new qcs6490-audioreach.dtsi file defines
nodes for AudioReach specific components such as APM (Audio Process
Manager), PRM (Proxy Resource Manager), and GPR (Generic Packet Router).
This change enable the audio from the legacy ADSP Bypass solution to
the AudioReach framework.
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250903151337.1037246-3-mohammad.rafi.shaik@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Device tree for the Lenovo Thinkbook 16 G7 QOY
The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].
Supported features:
- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera
- X1-45 GPU
Not supported yet:
- HDMI port.
- EC and some fn hotkeys.
Limited support yet:
- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.
This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1e device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).
Co-developed-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Link: https://lore.kernel.org/r/20250822-tb16-dt-v12-3-bab6c2986351@oldschoolsolutions.biz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: f9a9c11471 ("arm64: dts: qcom: x1e80100-qcp: Enable more support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-10-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: 09d77be560 ("arm64: dts: qcom: Add support for X1-based Surface Laptop 7 devices")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-9-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: 45247fe17d ("arm64: dts: qcom: x1e80100: add Lenovo Thinkpad Yoga slim 7x devicetree")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-8-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: 6f18b8d414 ("arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-7-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: f5b788d0e8 ("arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345")
Tested-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com> # 3K OLED
Reviewed-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-6-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: d0e2f8f62d ("arm64: dts: qcom: Add device tree for ASUS Vivobook S 15")
Tested-by: Maud Spierings <maud_spierings@hotmail.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-5-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: 7d1cbe2f49 ("arm64: dts: qcom: Add X1E78100 ThinkPad T14s Gen 6")
Tested-by: Christopher Obbard <christopher.obbard@linaro.org>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14s OLED
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-4-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: d7e03cce04 ("arm64: dts: qcom: x1e80100-crd: Enable more support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-3-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Fix this by adding the missing pinctrl for gpio119 (func1/edp0_hot and
bias-disable according to the ACPI DSDT), which is defined as
&edp0_hpd_default template in x1e80100.dtsi.
Fixes: 6516961352 ("arm64: dts: qcom: Add support for X1-based Asus Zenbook A14")
Tested-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com> # FHD OLED
Reviewed-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-2-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, we indirectly rely on the boot firmware to set up the
pinctrl for the eDP HPD line coming from the internal display. If the boot
firmware does not configure the display (e.g. because a different display
is selected for output in the UEFI settings), then the display fails to
come up and there are several errors in the kernel log:
[drm:dpu_encoder_phys_vid_wait_for_commit_done:544] [dpu error]vblank timeout: 80020041
[drm:dpu_kms_wait_for_commit_done:524] [dpu error]wait for commit done returned -110
[drm:dpu_encoder_frame_done_timeout:2715] [dpu error]enc40 frame done timeout
...
Add a new &edp0_hpd_default pinctrl template that can be used by boards to
set up the eDP HPD pin correctly. All boards upstream so far need the same
configuration; if a board needs a different configuration it can just avoid
using this template and define a custom one in the board DT.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250822-x1e80100-add-edp-hpd-v2-1-6310176239a6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
