Add a common allocator function for struct intel_digital_port, with some
member default initialization to deduplicate them from everywhere
else. This is similar to intel_connector_alloc().
At least for now, place this in intel_encoder.[ch]. We don't have a
dedicated file for dig port stuff, and there wouldn't be much to add
there anyway. A digital port is a sort of subclass of encoder, so the
location isn't far off the mark.
Reviewed-by: Dibin Moolakadan Subrahmanian <dibin.moolakadan.subrahmanian@intel.com>
Link: https://lore.kernel.org/r/4d2da1a40698f85014140f586405b19795437e81.1753787803.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On LNL+ for a disconnected sink the pin assignment value gets cleared by
the HW/FW as soon as the sink gets disconnected, even if the PHY
ownership got acquired already by the BIOS/driver (and hence the PHY
itself is still connected and used by the display). During HW readout
this can result in detecting the PHY's max lane count as 0 - matching
the above cleared aka NONE pin assignment HW state. For a connected PHY
the driver in general (outside of intel_tc.c) expects the max lane count
value to be valid for the video mode enabled on the corresponding output
(1, 2 or 4). Ensure this by setting the max lane count to 4 in this
case. Note, that it doesn't matter if this lane count happened to be
more than the max lane count with which the PHY got connected and
enabled, since the only thing the driver can do with such an output -
where the DP-alt sink is disconnected - is to disable the output.
v2: Rebased on change reading out the pin configuration only if the PHY
is connected.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-4-imre.deak@intel.com
The PHY's pin assignment value in the TCSS_DDI_STATUS register - as set
by the HW/FW based on the connected DP-alt sink's TypeC/PD pin
assignment negotiation - gets cleared by the HW/FW on LNL+ as soon as
the sink gets disconnected, even if the PHY ownership got acquired
already by the driver (and hence the PHY itself is still connected and
used by the display). This is similar to how the PHY Ready flag gets
cleared on LNL+ in the same register.
To be able to query the max lane count value on LNL+ - which is based on
the above pin assignment - at all times even after the sink gets
disconnected, the max lane count must be determined and cached during
the PHY's HW readout and connect sequences. Do that here, leaving the
actual use of the cached value to a follow-up change.
v2: Don't read out the pin configuration if the PHY is disconnected.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-3-imre.deak@intel.com
The TypeC PHY HW readout during driver loading and system resume
determines which TypeC mode the PHY is in (legacy/DP-alt/TBT-alt) and
whether the PHY is connected, based on the PHY's Owned and Ready flags.
For the PHY to be in DP-alt or legacy mode and for the PHY to be in the
connected state in these modes, both the Owned (set by the BIOS/driver)
and the Ready (set by the HW) flags should be set.
On ICL-MTL the HW kept the PHY's Ready flag set after the driver
connected the PHY by acquiring the PHY ownership (by setting the Owned
flag), until the driver disconnected the PHY by releasing the PHY
ownership (by clearing the Owned flag). On LNL+ this has changed, in
that the HW clears the Ready flag as soon as the sink gets disconnected,
even if the PHY ownership was acquired already and hence the PHY is
being used by the display.
When inheriting the HW state from BIOS for a PHY connected in DP-alt
mode on which the sink got disconnected - i.e. in a case where the sink
was connected while BIOS/GOP was running and so the sink got enabled
connecting the PHY, but the user disconnected the sink by the time the
driver loaded - the PHY Owned but not Ready state must be accounted for
on LNL+ according to the above. Do that by assuming on LNL+ that the PHY
is connected in DP-alt mode whenever the PHY Owned flag is set,
regardless of the PHY Ready flag.
This fixes a problem on LNL+, where the PHY TypeC mode / connected state
was detected incorrectly for a DP-alt sink, which got connected and then
disconnected by the user in the above way.
v2: Rename tc_phy_in_legacy_or_dp_alt_mode() to tc_phy_owned_by_display().
(Luca, Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
[Imre: Add one-liner function documentation for tc_phy_owned_by_display()]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-2-imre.deak@intel.com
We want to get rid of triggering "Frame Change" events from
frontbuffer flush calls. We are about to move using TRANS_PUSH
register for this on LunarLake and onwards. Touching TRANS_PUSH
register from fronbuffer flush would be problematic as it's written by
DSB as well.
Fix this by using intel_psr_exit when flush or invalidate is done on
LunarLake and onwards. This is not possible on AlderLake and
MeteorLake due to HW bug in PSR2 disable.
This patch is also fixing problems with cursor plane where cursor is
disappearing or duplicate cursor is seen on the screen.
v2: Commit message updated
Bspec: 68927, 68934, 66624
Reported-by: Janna Martl <janna.martl109@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/5522
Fixes: 411ad63877 ("drm/i915/psr: Use SFF_CTL on invalidate/flush for LunarLake onwards")
Tested-by: Janna Martl <janna.martl109@gmail.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250801062905.564453-1-jouni.hogander@intel.com
Mask the ERR_FATAL_MASK before scaler initialization.
After enabling the scaler and waiting for one frame,
unmask the previously masked bits, PS_ECC and
ERR_FATAL_MASK
Unmasking of ERR_FATAL_MASK bit is use for
validation purpose. There is no functional
impact.
v2: Remove intel_display_need_wa[Jani]
Optimize the ecc_unmask call[Animesh]
v3: Add intel_display_wa[Jani]
Signed-off-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250801125835.2337614-1-nemesa.garg@intel.com
It has been observed that during `xe_display_pm_suspend()` execution,
an HPD interrupt can still be triggered, resulting in `dig_port_work`
being scheduled. The issue arises when this work executes after
`xe_display_pm_suspend_late()`, by which time the display is fully
suspended.
This can lead to errors such as "DC state mismatch", as the dig_port
work accesses display resources that are no longer available or
powered.
To address this, introduce 'intel_encoder_block_all_hpds' and
'intel_encoder_unblock_all_hpds' functions, which iterate over all
encoders and block/unblock HPD respectively.
These are used to:
- Block HPD IRQs before calling 'intel_hpd_cancel_work' in suspend
and shutdown
- Unblock HPD IRQs after 'intel_hpd_init' in resume
This will prevent 'dig_port_work' being scheduled during display
suspend.
Continuation of previous patch discussion:
https://patchwork.freedesktop.org/patch/663964/
Changes in v2:
- Add 'intel_encoder_block_all_hpds' to 'xe_display_pm_shutdown'.(Imre
Deak)
- Add 'intel_hpd_cancel_work' to 'xe_display_fini_early' to cancel
any HPD pending work at late driver removal. (Imre Deak)
Changes in v3:
- Move 'intel_encoder_block_all_hpds' after intel_dp_mst_suspend
in 'xe_display_pm_shutdown'.(Imre Deak)
Signed-off-by: Dibin Moolakadan Subrahmanian <dibin.moolakadan.subrahmanian@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250724083928.2298199-1-dibin.moolakadan.subrahmanian@intel.com
Use recommended values as per wa_14021694213 to compare with the
calculated value and choose minimum of them.
v2: corrected checkpatch warning and retain the restriction for
min_hblank (Jani)
v3: use calculated value to compare with recomended value and choose
minimum of them (Imre)
v4: As driver supported min bpc is 8, omit the condition check for
bpc6 with ycbcr420. Added a note for the same (Imre)
v5: Add a warn for the unexpected case of 6bpc + uhbr + ycbcr420
v6: Reworded the comments and check fo anything < compressed bpp 8(Imre)
v7: Fix checkpatch warning. (Ankit)
Bspec: 74379
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250730-min_hblank-v7-1-179360220ced@intel.com
As per the wa_18038517565, we need to disable FBC compressor
clock gating before enabling FBC and enable after disabling
FBC. Placing the enabling of clock gating in the fbc deactivate
function can make the above wa logic go wrong in case of
frontbuffer rendering FBC mechanism. FBC deactivate can get
called during fb invalidate and then the corresponding FBC
activate can get called without properly disabling the clock
gating and can result in compression stalled. So move the
enable clock gating at the end of one FBC session after FBC
is completely disabled for a pipe.
Bspec: 74212, 72197, 69741, 65555
Fixes: 010363c461 ("drm/i915/display: implement wa_18038517565")
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://lore.kernel.org/r/20250729124648.288497-1-vinod.govindapillai@intel.com
The Fixed: commit below overlooked the fact that
intel_dp_link_train_all_phys() is only used for non-UHBR link rates, but
intel_dp_stop_link_train() is used for both non-UHBR and UHBR link
rates. Hence, after removing the disabling of the training pattern from
intel_dp_stop_link_train(), the commit missed adding this back to the
end of UHBR link training in intel_dp_128b132b_link_train(). This left
the sink in link training mode at the end of an UHBR rate link training.
Fix things by disabling the training pattern at the end of UHBR link
training as well.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 11fab5a2a1 ("drm/i915/dp: Clear DPCD training pattern before transmitting the idle pattern")
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250724182900.160891-1-imre.deak@intel.com
Selecting an option which depends on other options only works if the
dependencies are guaranteed to be selected (as these dependencies will
not be automatically selected). CONFIG_DRM_KUNIT_TEST depends on DRM,
MMU and KUNIT the first two of which are guaranteed to be selected for
i915, but the last one is not. Hence, selecting CONFIG_DRM_KUNIT_TEST in
i915 debug builds may result in CONFIG_DRM_KUNIT_TEST being selected
without the CONFIG_KUNIT dependency being selected. This causes at least
the following compile error:
drivers/gpu/drm/tests/drm_bridge_test.c: In function ‘drm_test_bridge_alloc_init’:
drivers/gpu/drm/tests/drm_bridge_test.c:449:21: error: implicit declaration of function ‘kunit_device_register’; did you mean ‘root_device_register’? [-Werror=implicit-function-declaration]
449 | priv->dev = kunit_device_register(test, "drm-bridge-dev");
Fix the above by selecting CONFIG_DRM_KUNIT_TEST only if CONFIG_KUNIT is
also selected.
Fixes: 17133255a3 ("drm/i915: replace DRM_DEBUG_SELFTEST with DRM_KUNIT_TEST")
Cc: Ruben Wauters <rubenru09@aol.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250724090237.92040-1-imre.deak@intel.com
dma_fence_wait_timeout returns a long type but the driver is
only using the lower 32 bits of the retval and discarding the
upper 32 bits.
This is particularly problematic if there are already signalled
or stub fences on some of the hw planes. In this case the
dma_fence_wait_timeout function will immediately return with
timeout value MAX_SCHEDULE_TIMEOUT (0x7fffffffffffffff) since
the fence is already signalled. If the driver only uses the lower
32 bits of this return value then it'll interpret it as an error
code (0xFFFFFFFF or (-1)) and skip the wait on the remaining fences.
This issue was first observed in the xe driver with the Android
compositor where the GPU composited layer was not properly waited
on when there were stub fences in other overlay planes resulting in
visual artifacts.
Fixes: d59cf7bb73 ("drm/i915/display: Use dma_fence interfaces instead of i915_sw_fence")
Signed-off-by: Aakash Deep Sarkar <aakash.deep.sarkar@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250708074540.1948068-1-aakash.deep.sarkar@intel.com
We are seeing "dmesg-warn/abort - *ERROR* PHY * failed after 3 retries"
since we started configuring LFPS sending. According to Bspec Configuring
LFPS sending is needed only when using AUXLess ALPM. This patch avoids
these failures by configuring LFPS sending only when using AUXLess ALPM.
Bspec: 68849
Fixes: 9dc619680d ("drm/i915/display: Add function to configure LFPS sending")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://lore.kernel.org/r/20250722125618.1842615-2-jouni.hogander@intel.com
DRM_DEBUG_SELFTEST was removed in commit fc8d29e298 (drm: selftest:
convert drm_mm selftest to KUnit) and all functions under it were
converted to KUnit, under the DRM_KUNIT_TEST option
This conversion however did not occur in the Kconfig.debug file in the
i915 directory.
This patch replaces the select for DRM_DEBUG_SELFTEST, an option that no
longer exists, with the correct select, DRM_KUNIT_TEST.
Signed-off-by: Ruben Wauters <rubenru09@aol.com>
Link: https://lore.kernel.org/r/20250701115511.5445-1-rubenru09@aol.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
