The AM64x SoCs have 2 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. Both the R5F clusters are present within the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a new "Single-CPU" mode
or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
The mode is restricted to "Single-CPU" on some devices with the
appropriate eFuse bit set, but the most common devices support both
modes. These subsystems have 64 KB each Tightly-Coupled Memory (TCM)
internal memories for each core split between two banks - ATCM and
BTCM (further interleaved into two banks). The TCMs of both Cores
are combined in Single-CPU mode to provide a larger 128 KB of memory.
The other notable difference is that the TCMs are spaced 1 MB apart
on these SoCs unlike the existing SoCs.
Add the DT nodes for both these MAIN domain R5F cluster/subsystems,
the two R5F cores are added as child nodes to each of the corresponding
R5F cluster node. Both the clusters are configured to run in Split mode
by default, with the ATCMs enabled to allow the R5 cores to execute
code from DDR with boot-strapping code from ATCM. The inter-processor
communication between the main A72 cores and these processors is
achieved through shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if desired:
MAIN R5FSS0 Core0: am64-main-r5f0_0-fw (both in Single-CPU & Split modes)
MAIN R5FSS0 Core1: am64-main-r5f0_1-fw (needed only in Split mode)
MAIN R5FSS1 Core0: am64-main-r5f1_0-fw (both in Single-CPU & Split modes)
MAIN R5FSS1 Core1: am64-main-r5f1_1-fw (needed only in Split mode)
NOTE:
A R5FSS cluster can be configured in "Single-CPU" mode by using a
value of 2 for the "ti,cluster-mode" property. Value of 1 is not
permitted (fails the dtbs_check).
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210615195718.15898-2-s-anna@ti.com
Due to a limitation for USB DFU boot mode, SPL load address has to be less
than or equal to 0x70001000. So, load address of SPL and TF-A have been
moved to 0x70000000 and 0x701c0000 respectively, in U-Boot version 2021.10.
Therefore, update TF-A's location in the device tree node.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210616171224.24635-4-a-govindraju@ti.com
8250_omap compatible UART IPs on all SoCs have registers aligned at 4
byte address boundary and constant byte addressability. Thus there is no
need for reg-io-width or reg-shift DT properties. These properties are
not used by 8250_omap driver nor documented as part of binding document.
Therefore drop them.
This is in preparation to move omap-serial.txt to YAML format.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210607134558.23704-1-vigneshr@ti.com
The current device tree CPSW3g node adds non-zero "mac-address" property to
the ports, which prevents random MAC address assignment to network devices
if bootloader failed to update DT. This may cause more then one host to
have the same MAC in the network.
mac-address = [00 00 de ad be ef];
mac-address = [00 01 de ad be ef];
In addition, there is one MAC address available in eFuse registers which
can be used for default port 1.
Hence, fix ports MAC properties by:
- resetting "mac-address" property to 0
- adding ti,syscon-efuse = <&main_conf 0x200> to Port 1
Fixes: 3753b12877 ("arm64: dts: ti: k3-am64-main: Add CPSW DT node")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210608184940.25934-1-grygorii.strashko@ti.com
Commit 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board:
Configure the PCIe instances") and
commit 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed
support for USB0") added PHY DT nodes with node name as "link"
However nodes with #phy-cells should be named 'phy' as discussed in [1].
Re-name subnodes of serdes in J721E to 'phy'.
[1] -> http://lore.kernel.org/r/20200909203631.GA3026331@bogus
Fixes: 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board: Configure the PCIe instances")
Fixes: 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-5-kishon@ti.com
Add #clock-cells property to serdes DT node since the serdes is also now
modeled as a clock provider and include the input clocks "pll0_refclk"
and "pll1_refclk" which are parents to the clocks modeled by serdes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-3-kishon@ti.com
Rename the external refclk inputs to the SERDES from
dummy_cmn_refclk/dummy_cmn_refclk1 to cmn_refclk/cmn_refclk1
respectively. Also move the external refclk DT nodes outside the
cbass_main DT node. Since in j721e common processor board, only the
cmn_refclk1 is connected to 100MHz clock, fix the clock frequency.
Fixes: afd094ebe6 ("arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-2-kishon@ti.com
The ICSSGs on K3 J721E SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-j721e-main.dtsi
file by default, and disabled in the existing J721E board dts
file. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-3-s-anna@ti.com
The ICSSGs on K3 AM65x SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-am65-main.dtsi
file by default, and disabled in the existing AM65 board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[s-anna@ti.com: move the disabled status to board dts files]
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-2-s-anna@ti.com
UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
Add support by removing the no-1-8-v tag and including the voltage
regulator device tree nodes for power cycling.
However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
boot mode for development usecases, continue to enable SD card and disable
UHS-I modes in it to minimize any ageing issues happening because of
erratas.
k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of
the common iot2050 device tree file.
[1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
[2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210529033749.6250-1-a-govindraju@ti.com
The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.
Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
The K3 AM64x SoCs have two dual-core Arm R5F clusters/subsystems, with
2 R5F cores each, both in the MAIN voltage domain.
These clusters are a revised IP version compared to those present on
J721E and J7200 SoCs, and supports a new "Single-CPU" mode instead of
LockStep mode. Update the K3 R5F remoteproc bindings with the compatible
info relevant to these R5F clusters/subsystems on K3 AM64x SoCs.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210327143117.1840-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There are no sub-mailbox devices defined currently for both the
IOT2050 boards. These are usually dictated by the firmwares running
on the R5F remote processors and the applications they provide.
Defining the actual sub-mailboxes will also dictate the interrupts
the clusters will use for interrupts on the Cortex-A53 cores.
Disable all of the Mailbox clusters until the sub-mailboxes are
defined and used. This fixes the warnings around the missing
interrupts with the upcoming conversion of the OMAP Mailbox binding
to YAML format.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210514212016.3153-1-s-anna@ti.com
Interrupt routers are memory mapped peripherals, that are organized
in our dts bus hierarchy to closely represents the actual hardware
behavior.
However, without explicitly calling out the reg property, using
2021.03+ dt-schema package, this exposes the following problem with
dtbs_check:
/arch/arm64/boot/dts/ti/k3-am654-base-board.dt.yaml: bus@100000:
interrupt-controller0: {'type': 'object'} is not allowed for
{'compatible': ['ti,sci-intr'], .....
Even though we don't use interrupt router directly via memory mapped
registers and have to use it via the system controller, the hardware
block is memory mapped, so describe the base address in device tree.
This is a valid, comprehensive description of hardware and permitted
by the existing ti,sci-intr schema.
Reviewed-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210511194821.13919-1-nm@ti.com
Instead of using empty ranges property, lets map explicitly the address
range that is mapped onto the dma / navigator subsystems (navss/dmss).
This is also exposed via the dtbs_check with dt-schema newer than
2021.03 version by throwing out following:
arch/arm64/boot/dts/ti/k3-am654-base-board.dt.yaml: bus@100000: main-navss:
{'type': 'object'} is not allowed for
{'compatible': ['simple-mfd'], '#address-cells': [[2]], .....
This has already been correctly done for J7200, however was missed for
other k3 SoCs. Fix that oversight.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210510145429.8752-1-nm@ti.com
The DMSC node does'nt require any of "#address-cells", "#size-cells"
or "ranges" property as the child nodes are representations of SoC's
system controller itself, so align it with the bindings.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-4-nm@ti.com
We currently use clocks as the node name for the node representing
TI-SCI clock nodes. This is better renamed to being clock-controller
as that is a better representative of the system controller function
as a clock controller for the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-2-nm@ti.com
Traffic through main NAVSS interconnect is coherent wrt ARM caches on
J7200 SoC. Add missing dma-coherent property to main_navss node.
Also add dma-ranges to be consistent with mcu_navss node
and with AM65/J721e main_navss and mcu_navss nodes.
Fixes: d361ed8845 ("arm64: dts: ti: Add support for J7200 SoC")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210510180601.19458-1-vigneshr@ti.com
AM654 EVM boards are not shipped with OV5640 sensor module, it is a
separate purchase. OV5640 module is also just one of the possible
sensors or capture boards you can connect.
However, for some reason, OV5640 has been added to the board dts file,
making it cumbersome to use other sensors.
Remove the OV5640 from the dts file so that it is easy to use other
sensors via DT overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210423083120.73476-1-tomi.valkeinen@ideasonboard.com
Commit b9d79e4ca4 ("fbmem: Mark proc_fb_seq_ops as __maybe_unused")
places the '__maybe_unused' in an entirely incorrect location between
the "struct" keyword and the structure name.
It's a wonder that gcc accepts that silently, but clang quite reasonably
warns about it:
drivers/video/fbdev/core/fbmem.c:736:21: warning: attribute declaration must precede definition [-Wignored-attributes]
static const struct __maybe_unused seq_operations proc_fb_seq_ops = {
^
Fix it.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm fixes from Dave Airlie:
"Bit later than usual, I queued them all up on Friday then promptly
forgot to write the pull request email. This is mainly amdgpu fixes,
with some radeon/msm/fbdev and one i915 gvt fix thrown in.
amdgpu:
- MPO hang workaround
- Fix for concurrent VM flushes on vega/navi
- dcefclk is not adjustable on navi1x and newer
- MST HPD debugfs fix
- Suspend/resumes fixes
- Register VGA clients late in case driver fails to load
- Fix GEM leak in user framebuffer create
- Add support for polaris12 with 32 bit memory interface
- Fix duplicate cursor issue when using overlay
- Fix corruption with tiled surfaces on VCN3
- Add BO size and stride check to fix BO size verification
radeon:
- Fix off-by-one in power state parsing
- Fix possible memory leak in power state parsing
msm:
- NULL ptr dereference fix
fbdev:
- procfs disabled warning fix
i915:
- gvt: Fix a possible division by zero in vgpu display rate
calculation"
* tag 'drm-next-2021-05-10' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: Use device specific BO size & stride check.
drm/amdgpu: Init GFX10_ADDR_CONFIG for VCN v3 in DPG mode.
drm/amd/pm: initialize variable
drm/radeon: Avoid power table parsing memory leaks
drm/radeon: Fix off-by-one power_state index heap overwrite
drm/amd/display: Fix two cursor duplication when using overlay
drm/amdgpu: add new MC firmware for Polaris12 32bit ASIC
fbmem: Mark proc_fb_seq_ops as __maybe_unused
drm/msm/dpu: Delete bonkers code
drm/i915/gvt: Prevent divided by zero when calculating refresh rate
amdgpu: fix GEM obj leak in amdgpu_display_user_framebuffer_create
drm/amdgpu: Register VGA clients after init can no longer fail
drm/amdgpu: Handling of amdgpu_device_resume return value for graceful teardown
drm/amdgpu: fix r initial values
drm/amd/display: fix wrong statement in mst hpd debugfs
amdgpu/pm: set pp_dpm_dcefclk to readonly on NAVI10 and newer gpus
amdgpu/pm: Prevent force of DCEFCLK on NAVI10 and SIENNA_CICHLID
drm/amdgpu: fix concurrent VM flushes on Vega/Navi v2
drm/amd/display: Reject non-zero src_y and src_x for video planes
Pull block fix from Jens Axboe:
"Turns out the bio max size change still has issues, so let's get it
reverted for 5.13-rc1. We'll shake out the issues there and defer it
to 5.14 instead"
* tag 'block-5.13-2021-05-09' of git://git.kernel.dk/linux-block:
Revert "bio: limit bio max size"
Pull cifs fixes from Steve French:
"Three small SMB3 chmultichannel related changesets (also for stable)
from the SMB3 test event this week.
The other fixes are still in review/testing"
* tag '5.13-rc-smb3-part3' of git://git.samba.org/sfrench/cifs-2.6:
smb3: if max_channels set to more than one channel request multichannel
smb3: do not attempt multichannel to server which does not support it
smb3: when mounting with multichannel include it in requested capabilities
Pull scheduler fixes from Thomas Gleixner:
"A set of scheduler updates:
- Prevent PSI state corruption when schedule() races with cgroup
move.
A recent commit combined two PSI callbacks to reduce the number of
cgroup tree updates, but missed that schedule() can drop rq::lock
for load balancing, which opens the race window for
cgroup_move_task() which then observes half updated state.
The fix is to solely use task::ps_flags instead of looking at the
potentially mismatching scheduler state
- Prevent an out-of-bounds access in uclamp caused bu a rounding
division which can lead to an off-by-one error exceeding the
buckets array size.
- Prevent unfairness caused by missing load decay when a task is
attached to a cfs runqueue.
The old load of the task was attached to the runqueue and never
removed. Fix it by enforcing the load update through the hierarchy
for unthrottled run queue instances.
- A documentation fix fot the 'sched_verbose' command line option"
* tag 'sched-urgent-2021-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix unfairness caused by missing load decay
sched: Fix out-of-bound access in uclamp
psi: Fix psi state corruption when schedule() races with cgroup move
sched,doc: sched_debug_verbose cmdline should be sched_verbose
Pull locking fixes from Thomas Gleixner:
"A set of locking related fixes and updates:
- Two fixes for the futex syscall related to the timeout handling.
FUTEX_LOCK_PI does not support the FUTEX_CLOCK_REALTIME bit and
because it's not set the time namespace adjustment for clock
MONOTONIC is applied wrongly.
FUTEX_WAIT cannot support the FUTEX_CLOCK_REALTIME bit because its
always a relative timeout.
- Cleanups in the futex syscall entry points which became obvious
when the two timeout handling bugs were fixed.
- Cleanup of queued_write_lock_slowpath() as suggested by Linus
- Fixup of the smp_call_function_single_async() prototype"
* tag 'locking-urgent-2021-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Make syscall entry points less convoluted
futex: Get rid of the val2 conditional dance
futex: Do not apply time namespace adjustment on FUTEX_LOCK_PI
Revert 337f13046f ("futex: Allow FUTEX_CLOCK_REALTIME with FUTEX_WAIT op")
locking/qrwlock: Cleanup queued_write_lock_slowpath()
smp: Fix smp_call_function_single_async prototype
Pull x86 perf fix from Borislav Petkov:
"Handle power-gating of AMD IOMMU perf counters properly when they are
used"
* tag 'perf_urgent_for_v5.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/events/amd/iommu: Fix invalid Perf result due to IOMMU PMC power-gating
Pull x86 fixes from Borislav Petkov:
"A bunch of things accumulated for x86 in the last two weeks:
- Fix guest vtime accounting so that ticks happening while the guest
is running can also be accounted to it. Along with a consolidation
to the guest-specific context tracking helpers.
- Provide for the host NMI handler running after a VMX VMEXIT to be
able to run on the kernel stack correctly.
- Initialize MSR_TSC_AUX when RDPID is supported and not RDTSCP (virt
relevant - real hw supports both)
- A code generation improvement to TASK_SIZE_MAX through the use of
alternatives
- The usual misc and related cleanups and improvements"
* tag 'x86_urgent_for_v5.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM: x86: Consolidate guest enter/exit logic to common helpers
context_tracking: KVM: Move guest enter/exit wrappers to KVM's domain
context_tracking: Consolidate guest enter/exit wrappers
sched/vtime: Move guest enter/exit vtime accounting to vtime.h
sched/vtime: Move vtime accounting external declarations above inlines
KVM: x86: Defer vtime accounting 'til after IRQ handling
context_tracking: Move guest exit vtime accounting to separate helpers
context_tracking: Move guest exit context tracking to separate helpers
KVM/VMX: Invoke NMI non-IST entry instead of IST entry
x86/cpu: Remove write_tsc() and write_rdtscp_aux() wrappers
x86/cpu: Initialize MSR_TSC_AUX if RDTSCP *or* RDPID is supported
x86/resctrl: Fix init const confusion
x86: Delete UD0, UD1 traces
x86/smpboot: Remove duplicate includes
x86/cpu: Use alternative to generate the TASK_SIZE_MAX constant
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to avoid over-allocating the kernel's mapping on !MMU systems,
which could lead to up to 2MiB of lost memory
- The SiFive address extension errata only manifest on rv64, they are
now disabled on rv32 where they are unnecessary
- A pair of late-landing cleanups
* tag 'riscv-for-linus-5.13-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused handle_exception symbol
riscv: Consistify protect_kernel_linear_mapping_text_rodata() use
riscv: enable SiFive errata CIP-453 and CIP-1200 Kconfig only if CONFIG_64BIT=y
riscv: Only extend kernel reservation if mapped read-only
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes in various drivers (qla2xxx, ufs,
scsi_debug, lpfc) one doc fix and a fairly large update to the fnic
driver to remove the open coded iteration functions in favour of the
scsi provided ones"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Use scsi_host_busy_iter() to traverse commands
scsi: fnic: Kill 'exclude_id' argument to fnic_cleanup_io()
scsi: scsi_debug: Fix cmd_per_lun, set to max_queue
scsi: ufs: core: Narrow down fast path in system suspend path
scsi: ufs: core: Cancel rpm_dev_flush_recheck_work during system suspend
scsi: ufs: core: Do not put UFS power into LPM if link is broken
scsi: qla2xxx: Prevent PRLI in target mode
scsi: qla2xxx: Add marginal path handling support
scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found
scsi: ufs: core: Fix a typo in ufs-sysfs.c
scsi: lpfc: Fix bad memory access during VPD DUMP mailbox command
scsi: lpfc: Fix DMA virtual address ptr assignment in bsg
scsi: lpfc: Fix illegal memory access on Abort IOCBs
scsi: blk-mq: Fix build warning when making htmldocs
Pull more Kbuild updates from Masahiro Yamada:
- Convert sh and sparc to use generic shell scripts to generate the
syscall headers
- refactor .gitignore files
- Update kernel/config_data.gz only when the content of the .config
is really changed, which avoids the unneeded re-link of vmlinux
- move "remove stale files" workarounds to scripts/remove-stale-files
- suppress unused-but-set-variable warnings by default for Clang
as well
- fix locale setting LANG=C to LC_ALL=C
- improve 'make distclean'
- always keep intermediate objects from scripts/link-vmlinux.sh
- move IF_ENABLED out of <linux/kconfig.h> to make it self-contained
- misc cleanups
* tag 'kbuild-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
linux/kconfig.h: replace IF_ENABLED() with PTR_IF() in <linux/kernel.h>
kbuild: Don't remove link-vmlinux temporary files on exit/signal
kbuild: remove the unneeded comments for external module builds
kbuild: make distclean remove tag files in sub-directories
kbuild: make distclean work against $(objtree) instead of $(srctree)
kbuild: refactor modname-multi by using suffix-search
kbuild: refactor fdtoverlay rule
kbuild: parameterize the .o part of suffix-search
arch: use cross_compiling to check whether it is a cross build or not
kbuild: remove ARCH=sh64 support from top Makefile
.gitignore: prefix local generated files with a slash
kbuild: replace LANG=C with LC_ALL=C
Makefile: Move -Wno-unused-but-set-variable out of GCC only block
kbuild: add a script to remove stale generated files
kbuild: update config_data.gz only when the content of .config is changed
.gitignore: ignore only top-level modules.builtin
.gitignore: move tags and TAGS close to other tag files
kernel/.gitgnore: remove stale timeconst.h and hz.bc
usr/include: refactor .gitignore
genksyms: fix stale comment
...
