mvebu dt64 for 5.11 (part 1)
- Add support for IEI Puzzle-M801 board (Armada 8040 based)
- Add support ESPRESSObin-Ultra (Armada 3720 based)
- Clean-up and improve espressobin device tree
- Switch to per-port SATA interrupts on CP110 based SoC
- Use compliant node name for USB3 on CP110 based SoC
- Add heartbeat LED on mcbin singleshot
- Disable SMMU by default for Armada 7040 and 8040 to continued
supporting custom bot firmware
- Turris mox:
- add 3W power capability to SFP cage
- update ethernet-phy handle name
* tag 'mvebu-dt64-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada-3720-turris-mox: add 3W power capability to SFP cage
arm64: dts: marvell: keep SMMU disabled by default for Armada 7040 and 8040
arm64: dts: mcbin-singleshot: add heartbeat LED
arm64: dts: marvell: cp11x: Harmonize xHCI DT nodes name
arm64: dts: marvell: espressobin: Update link to V7 schematic
arm64: dts: armada-3720-turris-mox: update ethernet-phy handle name
arm64: dts: marvell: armada-cp110: Switch to per-port SATA interrupts
arm64: dts: marvell: add DT for ESPRESSObin-Ultra
arm64: dts: marvell: espressobin: Add support for LED2
arm64: dts: marvell: Add a device tree for the IEI Puzzle-M801 board
arm64: dts: marvell: espressobin: De-duplicate eMMC definitions
arm64: dts: marvell: espressobin: Get rid of duplicate serial aliases
arm64: dts: marvell: espressobin: Simplify v7 ethernet port labeling
Link: https://lore.kernel.org/r/87eekaj0i4.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.11, please pull the following:
- Rafal adds initial support for the Broadcom 4908 which are SoCs used
in home routers and are based on the DSL architecture and using
Broadcom Brahma-B53 CPUs.
* tag 'arm-soc/for-5.11/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: add config for Broadcom BCM4908 SoCs
arm64: dts: broadcom: add BCM4908 and Asus GT-AC5300 early DTS files
dt-bindings: arm: bcm: document BCM4908 bindings
Link: https://lore.kernel.org/r/20201128163410.1691529-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs changes for 5.11,
please pull the following:
- Vivek updates the Linksys EA9500 DTS by adding the two additional
switch port nodes (5 & 7), providing a flash partition layout to
make the device usable with OpenWrt, and finally switches to using
the pin controller rather than using mdio-mux to get the same outcome.
- Serge fixes the USB Device Tree nodes unit name to be conformant to
the recommended name patterns.
- Rafal re-arranges all the nodes that belonged to the CRU block to be
under the CRU node (such as PLLs). He also disables the USB3 PHY node
for devices that lack USB3 and adds USB3 support to the Luxul XWR-3150
DTS.
- Jonathan drops the incorrect 'io-channel-ranges' from the Cygnus SoC
DTSI.
- Maxime disables the Wi-Fi frequencies (around 2.4GHz) for HDMI on the
Raspberry Pi 4 due to some cross-talk between the two blocks.
- Pavel updates the DWC2 USB controller RX FIFO sizes to be more
accurate for all BCM283x (Raspberr Pi) SoCs.
- Florian updates all BCM5301x and NSP Device Tree files to allow
switching the Broadcom B53 Ethernet switch device tree binding to YAML.
* tag 'arm-soc/for-5.11/devicetree' of https://github.com/Broadcom/stblinux: (22 commits)
dt-bindings: net: dsa: b53: Add YAML bindings
ARM: dts: NSP: Provide defaults ports container node
ARM: dts: NSP: Add a SRAB compatible string for each board
ARM: dts: NSP: Fix Ethernet switch SGMII register name
ARM: dts: NSP: Update ethernet switch node name
ARM: dts: BCM5301X: Provide defaults ports container node
ARM: dts: BCM5301X: Add a default compatible for switch node
ARM: dts: BCM5301X: Update Ethernet switch node name
dt-bindings: net: dsa: Document sfp and managed properties
dt-bindings: net: dsa: Extend switch nodes pattern
ARM: dts: bcm283x: increase dwc2's RX FIFO size
ARM: dts: rpi-4: disable wifi frequencies
ARM: dts: Cygnus: Drop incorrect io-channel-ranges property.
ARM: dts: BCM5301X: Enable USB 3 PHY on Luxul XWR-3150
ARM: dts: BCM5301X: Disable USB 3 PHY on devices without USB 3
ARM: dts: BCM5301X: Move CRU devices to the CRU node
ARM: dts: BCM5301X: Linksys EA9500 make use of pinctrl
ARM: dts: BCM5301X: Use corretc pinctrl compatible for 4709x
ARM: dts: BCM5301X: Linksys EA9500 add fixed partitions
ARM: dts: BCM5310X: Harmonize xHCI DT nodes name
...
Link: https://lore.kernel.org/r/20201128163410.1691529-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
FW has to configure devices' StreamIDs so that SMMU is able to lookup
context and do proper translation later on. For Armada 7040 & 8040 and
publicly available FW, most of the devices are configured properly,
but some like ap_sdhci0, PCIe, NIC still remain unassigned which
results in SMMU faults about unmatched StreamID (assuming
ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=y).
Since there is dependency on custom FW let SMMU be disabled by default.
People who still willing to use SMMU need to enable manually and
use ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=n (or via kernel command line)
with extra caution.
Fixes: 83a3545d9c ("arm64: dts: marvell: add SMMU support")
Cc: <stable@vger.kernel.org> # 5.9+
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
With board revision 1.3, SolidRun moved the power LED to the middle of
the board. In old place of power LED a GPIO controllable heartbeat LED
was added. This commit only touches Single Shot variant, since only this
variant is all revision 1.3.
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In accordance with the Generic xHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-xhci"-compatible nodes are
correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Linux now has incomplete support for the LED controller on Turris Omnia:
it can set brightness and colors for each LED.
The controller can also put these LEDs into HW controlled mode, in which
the LEDs are controlled by HW: for example the WAN LED is connected via
MCU to the WAN PHY LED pin.
The driver does not support these HW controlled modes yet, and on probe
puts the LEDs into SW controlled mode.
Add node describing the LED controller, but disable it for now.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds support for ESPRESSObin-Ultra from Globalscale.
Specifications are similar to the base ESPRESSObin board, with main
difference being being WAN port with PoE capability and 2 additional ethernet ports.
Full specifications:
1x Marvell 64 bit Dual Core ARM A53 Armada 3700 SOC clocked up to 1.2Ghz
1x Topaz 6341 Networking Switch
1GB DDR4
8GB eMMC
1x WAN with 30W POE
4x Gb LAN
1x RTC Clock and battery
1x DC Jack
1x USB 3.0 Type A
1x USB 2.0 Type A
1x SIM NanoSIM card Slot
1x Power Button
4x LED
1x Reset button
1x microUSB for UART
1x M.2 2280 slot for memory
1x 2x2 802.11ac Wi-Fi
1x MiniPCIE slot for Wi-Fi (PCIe interface)
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
LED2 is connected to MPP1_2 pin. It is working only on V7 boards.
V5 boards have hw bug which cause that LED2 is non-working.
So enable LED2 only for Espressobin V7 boards.
Note that LED1 is connected to LED_WLAN# pin on miniPCIe card and LED3 to
power supply. Therefore on Espressobin board only LED2 can be controlled
directly from the host. LED1 is possible to control via WiFi card inserted
in miniPCIe slot if driver for particular card supports it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add initial support for the IEI Puzzle-M801 1U Rackmount Network
Appliance board.
The board is based on the quad-core Marvell Armada 8040 SoC and supports
up to 16 GB of DDR4 2400 MHz ECC RAM. It has a PCIe x16 slot (x2 lanes
only) and an M.2 type B slot.
Main system hardware:
2x USB 3.0
4x Gigabit Ethernet
2x SFP+
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x IEI WT61P803 PUZZLE Microcontroller
1x EPSON RX8010 RTC (used instead of the integrated Marvell RTC controller)
6x SFP+ LED
1x HDD LED
All of the hardware listed above is supported and tested in this port.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
eMMC definitions in files armada-3720-espressobin-emmc.dts and
armada-3720-espressobin-v7-emmc.dts is same. So move it into common
armada-3720-espressobin.dtsi file with status "disabled".
This change simplifies eMMC variants of DTS files for Espressobin.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Now that the switch ports have a label in the .dtsi, simplify the whole
"switch0" block for the v7 dts files.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba877 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
MikroTik CRS305-1G-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
arm64: tegra: Device tree changes for v5.11-rc1
These changes are mostly minor fixes across the board, but they also
enable PMUs on Tegra186 and enable SATA support on Jetson TX2.
* tag 'tegra-for-5.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix Tegra194 HDA {clock,reset}-names ordering
arm64: tegra: Enable AHCI on Jetson TX2
arm64: tegra: Change order of SATA resets for Tegra132 and Tegra210
arm64: tegra: Add XUSB pad controller interrupt
arm64: tegra: Rename ADMA device nodes for Tegra210
arm64: tegra: Hook up edp interrupt on Tegra132 SOCTHERM
arm64: tegra: Add missing hot temperatures to Tegra210 thermal-zones
arm64: tegra: Add missing gpu-throt-level to Tegra210 soctherm
arm64: tegra: Add missing hot temperatures to Tegra132 thermal-zones
arm64: tegra: Fix DT binding for IO High Voltage entry
arm64: tegra: Fix GIC400 missing GICH/GICV register regions
arm64: tegra: Add missing CPU PMUs on Tegra186
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
Link: https://lore.kernel.org/r/20201127144329.124891-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: tegra: Device tree changes for v5.11-rc1
This adds support for the Tegra30-based Ouya game console and enhances a
number of existing device trees. It also fixes a couple of minor issues
that were found during DT validation.
* tag 'tegra-for-5.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (23 commits)
ARM: tegra: Add EMC OPP and ICC properties to Tegra124 EMC and ACTMON device-tree nodes
ARM: tegra: Add EMC OPP and ICC properties to Tegra30 EMC and ACTMON device-tree nodes
ARM: tegra: Add EMC OPP properties to Tegra20 device-trees
ARM: tegra: Add nvidia,memory-controller phandle to Tegra20 EMC device-tree
ARM: tegra: Add interconnect properties to Tegra124 device-tree
ARM: tegra: Add interconnect properties to Tegra30 device-tree
ARM: tegra: Add interconnect properties to Tegra20 device-tree
ARM: tegra: acer-a500: Add Embedded Controller
ARM: tegra: Change order of SATA resets for Tegra124
ARM: tegra: Correct EMC registers size in Tegra20 device-tree
ARM: tegra: Properly align clocks for SOCTHERM
ARM: tegra: Hook up edp interrupt on Tegra124 SOCTHERM
ARM: tegra: Add missing hot temperatures to Tegra124 thermal-zones
ARM: tegra: Add missing gpu-throt-level to Tegra124 soctherm
ARM: tegra: Populate OPP table for Tegra20 Ventana
ARM: tegra: nexus7: Use panel-lvds as the only panel compatible
ARM: tegra: nexus7: Rename gpio-hog nodes
ARM: tegra: nexus7: Add power-supply to lvds-encoder node
ARM: tegra: nexus7: Improve CPU passive-cooling threshold
ARM: tegra: nexus7: Correct thermal zone names
...
Link: https://lore.kernel.org/r/20201127144329.124891-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Changes for v5.11-rc1
This contains a couple of conversions of bindings to json-schema, as
well as symbolic names for the various memory clients on Tegra20,
Tegra30 and Tegra124. There's also a couple of fixes for Tegra194
pinmux and ARM GIC bindings. Finally, a new vendor prefix is added
for Ouya and the Ouya game console compatible string is defined.
* tag 'tegra-for-5.11-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: bus: Convert ACONNECT doc to json-schema
dt-bindings: interrupt-controller: arm,gic: Update Tegra compatibles
dt-bindings: dma: Convert ADMA doc to json-schema
dt-bindings: Fix entry name for I/O High Voltage property
dt-bindings: ARM: tegra: Add Ouya game console
dt-bindings: Add vendor prefix for Ouya Inc.
dt-bindings: memory: tegra124: Add memory client IDs
dt-bindings: memory: tegra30: Add memory client IDs
dt-bindings: memory: tegra20: Add memory client IDs
Link: https://lore.kernel.org/r/20201127144329.124891-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas ARM DT updates for v5.11 (take two)
- PCIe endpoint support for the R-Car H3 ES2.0+ SoC.
* tag 'renesas-arm-dt-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a77951: Add PCIe EP nodes
Link: https://lore.kernel.org/r/20201127132155.77418-2-geert@linux-m68k.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT updates for v5.11, round 1
Highlights:
----------
MCU part:
-Fix dmamux reg property (length) on stm32h743.
-Explicitly set DCMI bus type on stm32429i eval board.
MPU part:
-Enable FIFO mode with half-full threshold for DCMI.
-Harmonize EHCI/OHCI nodes.
-Move SDMMC IP version to v2.0 to get features improvements.
-Add LP-timer wakeup support.
-Enable crypto/hash/crc support.
-Explicitly set DCMI bus type on stm32mp157 eval board.
-Add USB type-c controller (STUSB1600) on stm32mp15 DK boards
(It is connected to I2C4).
-Fix dmamux reg property (length) on stm32mp151.
-Optimize USB OTG FIFO sizes on stm32mp151.
-Declare tamp node also as "simple-mfd".
-LXA:
-Document Octavo vendor-prefixes yaml file.
-Document lxa,stm32mp157c-mc1 in STM32 yaml file.
-DH:
-Connect PHY IRQ line on DH SoM.
-Add KS8851 Ethernet support on DHCOM which is mapped to FMC2.
-Document all DH compatible strings in STM32 yaml file.
-Add DHCOM based PicoITX board. This board embedds ethernet port,
USB, CAN LEDS and a custom board-to-board connector.
* tag 'stm32-dt-for-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: lxa-mc1: add OSD32MP15x to list of compatibles
dt-bindings: arm: stm32: add extra SiP compatible for lxa,stm32mp157c-mc1
dt-bindings: vendor-prefixes: document Octavo Systems oct prefix
ARM: dts: stm32: Add DHCOM based PicoITX board
dt-bindings: arm: stm32: Add compatible strings for DH SoMs and boards
ARM: dts: stm32: support child mfd cells for the stm32mp1 TAMP syscon
dt-bindings: arm: stm32: add simple-mfd compatible for tamp node
ARM: dts: stm32: update stm32mp151 for remote proc synchronization support
ARM: dts: stm32: adjust USB OTG gadget fifo sizes in stm32mp151
ARM: dts: stm32: fix dmamux reg property on stm32h743
ARM: dts: stm32: fix dmamux reg property on stm32mp151
ARM: dts: stm32: fix mdma1 clients channel priority level on stm32mp151
ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx
dt-bindings: usb: Add DT bindings for STUSB160x Type-C controller
dt-bindings: connector: add typec-power-opmode property to usb-connector
ARM: dts: stm32: reorder spi4 within stm32mp15-pinctrl
ARM: dts: stm32: set bus-type in DCMI endpoint for stm32429i-eval board
ARM: dts: stm32: set bus-type in DCMI endpoint for stm32mp157c-ev1 board
ARM: dts: stm32: enable CRYP by default on stm32mp15
ARM: dts: stm32: enable CRC1 by default on stm32mp15
...
Link: https://lore.kernel.org/r/873c17a5-28d5-9261-f691-1b917611c932@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Devicetree changes for omaps for v5.11 merge window
- Two non-urgent pandaboard updates to get gpio button and bluetooth
working on pandaboard-es
- Updates to follow devicetree binding docs for dwc3 and pwm-leds
- Add initial support for droid bionic based on what we have for droid4
- Add second sha instance for dra7
- Add eQEP nodes for am335x for boneblue
- Fix wrong comments for am335x gpio_31
* tag 'omap-for-v5.11/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: Fix comments for AM335X_PIN_GPMC_WPN pin in GPIO mode
ARM: dts: am335x-boneblue: Enable eQEP
ARM: dts: am33xx: Add nodes for eQEP
ARM: dts: dra7: add second SHA instance
ARM: dts: xt875: add section for kionix kxtf9
ARM: dts: mapphone: separate out xt894 specific things
ARM: dts: omap: Fix schema warnings for pwm-leds
ARM: dts: omap5: Harmonize DWC USB3 DT nodes name
ARM: dts: am437x: Correct DWC USB3 compatible string
ARM: dts: pandaboard es: add bluetooth uart for HCI
ARM: dts: pandaboard: fix pinmux for gpio user button of Pandaboard ES
Link: https://lore.kernel.org/r/pull-1606462656-588116@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
