After commit bd99a3013b ("brcmfmac: move configuration of probe request
IEs"), the probe request MGMT IE addition operation brcmf_vif_set_mgmt_ie()
got moved from the brcmf_p2p_scan_prep() to the brcmf_cfg80211_scan().
Because of this, as part of the scan request handler for the P2P Discovery,
vif struct used for adding the Probe Request P2P IE in firmware got changed
from the P2PAPI_BSSCFG_DEVICE vif to P2PAPI_BSSCFG_PRIMARY vif incorrectly.
So the firmware stopped adding P2P IE to the outgoing P2P Discovery probe
requests frames and the other P2P peers were unable to discover this device
causing a regression on the P2P feature.
To fix this, while setting the P2P IE in firmware, properly use the vif of
the P2P discovery wdev on which the driver received the P2P scan request.
This is done by not changing the vif pointer, until brcmf_vif_set_mgmt_ie()
is completed.
Fixes: bd99a3013b ("brcmfmac: move configuration of probe request IEs")
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250626050706.7271-1-gokulkumar.sivakumar@infineon.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ignore TXQs with the flag IEEE80211_TXQ_STOP when scheduling a queue.
The flag is only set after all fragments have been dequeued and won't
allow dequeueing other frames as long as the flag is set.
For drivers using ieee80211_txq_schedule_start() this prevents an
loop trying to push the queued frames while IEEE80211_TXQ_STOP is set:
After setting IEEE80211_TXQ_STOP the driver will call
ieee80211_return_txq(). Which calls __ieee80211_schedule_txq(), detects
that there sill are frames in the queue and immediately restarts the
stopped TXQ. Which can't dequeue any frame and thus starts over the loop.
Signed-off-by: Alexander Wetzel <Alexander@wetzel-home.de>
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Link: https://patch.msgid.link/20250717162547.94582-2-Alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If probe fails before ieee80211_register_hw() is successfully done,
ieee80211_unregister_hw() will be called anyway. This may lead to various
bugs as the implementation of ieee80211_unregister_hw() assumes that
ieee80211_register_hw() has been called.
Divide error handling section into relevant subsections, so that
ieee80211_unregister_hw() is called only when it is appropriate. Correct
the order of the calls: ieee80211_unregister_hw() should go before
plfxlc_mac_release(). Also move ieee80211_free_hw() to plfxlc_mac_release()
as it supposed to be the opposite to plfxlc_mac_alloc_hw() that calls
ieee80211_alloc_hw().
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 68d57a07bf ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices")
Signed-off-by: Murad Masimov <m.masimov@mt-integration.ru>
Link: https://patch.msgid.link/20250321185226.71-3-m.masimov@mt-integration.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When short beaconing is enabled, check the value of the sb_count
to determine whether we are to send a long beacon or short beacon.
sb_count represents the number of short beacons until the next
long beacon, where if its value is 0 we are to send a long beacon.
The value is then reset to the long beacon period, which represents
the number of beacon intervals between each long beacon. The decrement
process follows the same cadence as the decrement of the DTIM count value.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-5-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the sb_count variable which tracks the number of
beacon intervals until the next long beacon. To initialise this
value, we find the current short beacon index into this period
which represents the number of short beacons left to send before
the next long beacon. We use the same TSF value used to initialise
the DTIM count to ensure the short beacon count and DTIM count
are in sync as its common for the long beacon period and DTIM period
to be equivalent.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-4-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the ability to parse the short beacon data and long
beacon period. The long beacon period represents the number of beacon
intervals between each long beacon transmission. Additionally,
as a BSS cannot change its configuration such that short beaconing
is dynamically disabled/enabled without tearing down the interface
- we ensure we have an existing short beacon before performing
the update.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-3-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G short beacons are an optional frame type used in an S1G BSS
that contain a limited set of elements. While they are optional,
they are a fundamental part of S1G that enables significant
power saving.
Expose 2 additional netlink attributes,
NL80211_ATTR_S1G_LONG_BEACON_PERIOD which denotes the number of beacon
intervals between each long beacon and NL80211_ATTR_S1G_SHORT_BEACON
which is a nested attribute containing the short beacon tail and
head. We split them as the long beacon period cannot be updated,
and is only used when initialisng the interface, whereas the short
beacon data can be used to both initialise and update the templates.
This follows how things such as the beacon interval and DTIM period
currently operate.
During the initialisation path, we ensure we have the long beacon
period if the short beacon data is being passed down, whereas
the update path will simply update the template if its sent down.
The short beacon data is validated using the same routines for regular
beacons as they support correctly parsing the short beacon format
while ensuring the frame is well-formed.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-2-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A new warning in clang [1] complains that diq_start in
wlc_lcnphy_tx_iqlo_cal() is passed uninitialized as a const pointer to
wlc_lcnphy_common_read_table():
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2728:13: error: variable 'diq_start' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
2728 | &diq_start, 1, 16, 69);
| ^~~~~~~~~
The table pointer passed to wlc_lcnphy_common_read_table() should not be
considered constant, as wlc_phy_read_table() is ultimately going to
update it. Remove the const qualifier from the tbl_ptr to clear up the
warning.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/2108
Fixes: 5b435de0d7 ("net: wireless: add brcm80211 drivers")
Link: 00dacf8c22 [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>>
Link: https://patch.msgid.link/20250715-brcmsmac-fix-uninit-const-pointer-v1-1-16e6a51a8ef4@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, reset connection monitor (ieee80211_sta_reset_conn_monitor())
timer is handled only for non-AP non-MLD STA and do not support non-AP MLD
STA. The current implementation checks for the CSA active and update the
monitor timer with the timeout value of deflink and reset the timer based
on the deflink's timeout value else schedule the connection loss work when
the deflink is timed out and it won't work for the non-AP MLD STA.
Handle the reset connection monitor timer for non-AP MLD STA by updating
the monitor timer with the timeout value which is determined based on the
link that will expire last among all the links in MLO. If at least one link
has not timed out, the timer is updated accordingly with the latest timeout
value else schedule the connection loss work when all links have timed out.
Remove the MLO-related WARN_ON() checks in the beacon and connection
monitoring logic code paths as they support MLO now.
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-5-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, reset beacon monitor (ieee80211_sta_reset_beacon_monitor())
timer is handled only for non-AP non-MLD STA and do not support non-AP MLD
STA. When the beacon loss occurs in non-AP MLD STA with the current
implementation, it is treated as a single link and the timer will reset
based on the timeout of the deflink, without checking all the links.
Check the CSA flags for all the links in the MLO and decide whether to
schedule the work queue for beacon loss. If any of the links has CSA
active, then beacon loss work is not scheduled.
Also, call the functions ieee80211_sta_reset_beacon_monitor() and
ieee80211_sta_reset_conn_monitor() from ieee80211_csa_switch_work() only
when all the links are CSA active.
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-4-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the existing macro for_each_link_data() uses sdata_dereference()
which requires the wiphy lock. This lock cannot be used in atomic or RCU
read-side contexts, such as in the RX path.
Introduce a new macro, for_each_link_data_rcu(), that iterates over link of
sdata using rcu_dereference(), making it safe to use in RCU contexts. This
allows callers to access link data without requiring the wiphy lock.
The macro takes into account the vif.valid_links bitmap and ensures only
valid links are accessed safely. Callers are responsible for ensuring that
rcu_read_lock() is held when using this macro.
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-3-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The for_each_link_data() macro currently declares a local variable
__sdata directly, which could lead to compiler warnings or errors when
reused in the same function or within switch-case blocks due to variable
redefinition or invalid scoping.
To address this, restructure the macro to use an outer for-loop that runs
only once, allowing safe declaration of __sdata without polluting the outer
scope. This ensures compatibility with static analyzers.
No functional changes; this is purely a cleanup to improve macro hygiene.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-2-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This (partially) reverts commits
- 838c7b8f1f ("wifi: nl80211: Avoid address calculations via out of bounds array indexing")
- f1d3334d60 ("wifi: cfg80211: sme: init n_channels before channels[] access")
- 82bbe02b25 ("wifi: mac80211: Set n_channels after allocating struct cfg80211_scan_request")
These commits all set the structure to be in an inconsistent
state, setting n_channels to some value before them actually
being filled in. That's fine for what the code does now, but
with the removal of __counted_by() in 444020f4bf ("wifi:
cfg80211: remove scan request n_channels counted_by") it's no
longer needed and it does leave a bit of a landmine there
since breaking out of some code to send the scan or something
would leave it wrong.
Remove the now superfluous n_channels settings.
Link: https://patch.msgid.link/20250718103237.59510b2384c5.Ied5ba9c5c49efc008f4491c8ca7a45858a83f064@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ping-Ke Shih says:
==================
rtw-next patches for v6.17
Some minor fixes and refinements. Major changes are listed:
rtw89:
- STA+P2P concurrency feature gets implemented.
- add USB architecture and support RTL8851BU and RTL8852BU.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In scheduled scan mode, the current probe request only includes the SSID
IE, but omits the Basic Rate IE. Some APs do not respond to such
incomplete probe requests, causing net-detect failures. To improve
interoperability and ensure APs respond correctly, add the Basic Rate IE
to the probe request in driver.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250716122926.6709-1-pkshih@realtek.com
When the chip is not powered on correctly (like during driver
development) rtw89_fwdl_check_path_ready_ax() can fail.
read_poll_timeout_atomic() with a delay of 1 µs and a timeout of
400000 µs can take 50 seconds with USB because of the time it takes to
send a USB control message. The firmware upload is tried 5 times, so
in total it takes 250 seconds.
Lower the timeout to 3200 for USB in order to reduce the time
rtw89_fwdl_check_path_ready_ax() takes from 50 seconds to less than 1
second.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/af0b25d0-ea67-455e-91f2-8e4c18ae4328@gmail.com
This read_poll_timeout_atomic() with a delay of 1 µs and a timeout of
1000000 µs can take ~250 seconds in the worst case because sending a
USB control message takes ~250 µs.
Lower the timeout to 4000 for USB in order to reduce the maximum polling
time to ~1 second.
This problem was observed with RTL8851BU while suspending to RAM with
WOWLAN enabled. The computer sat for 4 minutes with a black screen
before suspending.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/09313da6-c865-4e91-b758-4cb38a878796@gmail.com
The variable 'path' from rtw89_phy_get_syn_sel() as index of array could
be 3, but array size is 2. Fortunately, current chip->rf_path_num is
smaller or equal to 2, so it is safe. To prevent mistakes in the future,
add a checking and avoid Coverity warnings.
Addresses-Coverity-ID: linux-next: 1644716 ("Out-of-bounds write")
Addresses-Coverity-ID: linux-next: 1644717 ("Out-of-bounds write")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-6-pkshih@realtek.com
The queued and obsoleted scan events can be wrongly treated as events of
new scan request, causing unexpected scan result. Attach a software
sequence number to scan request and its corresponding events. When a new
scan request is acknowledged by firmware, purge the scan events if its
sequence number is not belong to current request.
Normal case:
mac80211 event work event BH
------------- ---------- --------
scan req #1 ---->o
|
<----o <...........................o
o
|
<--------------------------+
ieee80211_scan_completed()
Abnormal case (late event work):
mac80211 event work event BH
------------- ---------- --------
scan req #1 ---->o
|
<----o <...........................o
o #1
scan cancel #2 ->o
|
<----o <...........................o
o #2
| (patch to avoid this)
scan req #3 ---->o |
| |
<----o <..........|................o
| o #3
<--------------------------+
ieee80211_scan_completed()
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-5-pkshih@realtek.com
When the 'Disabled Subchannel Bitmap' within the EHT Operation
element is changed, mac80211 parse and pass it to the driver.
The driver is then updated with this puncturing bitmap to
optimize bandwidth usage and prevent interference from
degrading performance across the entire channel.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-4-pkshih@realtek.com
Pull networking fixes from Jakub Kicinski:
"Including fixes from Bluetooth, CAN, WiFi and Netfilter.
More code here than I would have liked. That said, better now than
next week. Nothing particularly scary stands out. The improvement to
the OpenVPN input validation is a bit large but better get them in
before the code makes it to a final release. Some of the changes we
got from sub-trees could have been split better between the fix and
-next refactoring, IMHO, that has been communicated.
We have one known regression in a TI AM65 board not getting link. The
investigation is going a bit slow, a number of people are on vacation.
We'll try to wrap it up, but don't think it should hold up the
release.
Current release - fix to a fix:
- Bluetooth: L2CAP: fix attempting to adjust outgoing MTU, it broke
some headphones and speakers
Current release - regressions:
- wifi: ath12k: fix packets received in WBM error ring with REO LUT
enabled, fix Rx performance regression
- wifi: iwlwifi:
- fix crash due to a botched indexing conversion
- mask reserved bits in chan_state_active_bitmap, avoid FW assert()
Current release - new code bugs:
- nf_conntrack: fix crash due to removal of uninitialised entry
- eth: airoha: fix potential UaF in airoha_npu_get()
Previous releases - regressions:
- net: fix segmentation after TCP/UDP fraglist GRO
- af_packet: fix the SO_SNDTIMEO constraint not taking effect and a
potential soft lockup waiting for a completion
- rpl: fix UaF in rpl_do_srh_inline() for sneaky skb geometry
- virtio-net: fix recursive rtnl_lock() during probe()
- eth: stmmac: populate entire system_counterval_t in get_time_fn()
- eth: libwx: fix a number of crashes in the driver Rx path
- hv_netvsc: prevent IPv6 addrconf after IFF_SLAVE lost that meaning
Previous releases - always broken:
- mptcp: fix races in handling connection fallback to pure TCP
- rxrpc: assorted error handling and race fixes
- sched: another batch of "security" fixes for qdiscs (QFQ, HTB)
- tls: always refresh the queue when reading sock, avoid UaF
- phy: don't register LEDs for genphy, avoid deadlock
- Bluetooth: btintel: check if controller is ISO capable on
btintel_classify_pkt_type(), work around FW returning incorrect
capabilities
Misc:
- make OpenVPN Netlink input checking more strict before it makes it
to a final release
- wifi: cfg80211: remove scan request n_channels __counted_by, it's
only yielding false positives"
* tag 'net-6.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
rxrpc: Fix to use conn aborts for conn-wide failures
rxrpc: Fix transmission of an abort in response to an abort
rxrpc: Fix notification vs call-release vs recvmsg
rxrpc: Fix recv-recv race of completed call
rxrpc: Fix irq-disabled in local_bh_enable()
selftests/tc-testing: Test htb_dequeue_tree with deactivation and row emptying
net/sched: Return NULL when htb_lookup_leaf encounters an empty rbtree
net: bridge: Do not offload IGMP/MLD messages
selftests: Add test cases for vlan_filter modification during runtime
net: vlan: fix VLAN 0 refcount imbalance of toggling filtering during runtime
tls: always refresh the queue when reading sock
virtio-net: fix recursived rtnl_lock() during probe()
net/mlx5: Update the list of the PCI supported devices
hv_netvsc: Set VF priv_flags to IFF_NO_ADDRCONF before open to prevent IPv6 addrconf
phonet/pep: Move call to pn_skb_get_dst_sockaddr() earlier in pep_sock_accept()
Bluetooth: L2CAP: Fix attempting to adjust outgoing MTU
netfilter: nf_conntrack: fix crash due to removal of uninitialised entry
net: fix segmentation after TCP/UDP fraglist GRO
ipv6: mcast: Delay put pmc->idev in mld_del_delrec()
net: airoha: fix potential use-after-free in airoha_npu_get()
...
Pull power management fixes from Rafael Wysocki:
"These address three issues introduced during the current development
cycle and related to system suspend and hibernation, one triggering
when asynchronous suspend of devices fails, one possibly affecting
memory management in the core suspend code error path, and one due to
duplicate filesystems freezing during system suspend:
- Fix a deadlock that may occur on asynchronous device suspend
failures due to missing completion updates in error paths (Rafael
Wysocki)
- Drop a misplaced pm_restore_gfp_mask() call, which may cause swap
to be accessed too early if system suspend fails, from
suspend_devices_and_enter() (Rafael Wysocki)
- Remove duplicate filesystems_freeze/thaw() calls, which sometimes
cause systems to be unable to resume, from enter_state() (Zihuan
Zhang)"
* tag 'pm-6.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: sleep: Update power.completion for all devices on errors
PM: suspend: clean up redundant filesystems_freeze/thaw() handling
PM: suspend: Drop a misplaced pm_restore_gfp_mask() call
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_sync: fix connectable extended advertising when using static random address
- hci_core: fix typos in macros
- hci_core: add missing braces when using macro parameters
- hci_core: replace 'quirks' integer by 'quirk_flags' bitmap
- SMP: If an unallowed command is received consider it a failure
- SMP: Fix using HCI_ERROR_REMOTE_USER_TERM on timeout
- L2CAP: Fix null-ptr-deref in l2cap_sock_resume_cb()
- L2CAP: Fix attempting to adjust outgoing MTU
- btintel: Check if controller is ISO capable on btintel_classify_pkt_type
- btusb: QCA: Fix downloading wrong NVM for WCN6855 GF variant without board ID
* tag 'for-net-2025-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix attempting to adjust outgoing MTU
Bluetooth: btusb: QCA: Fix downloading wrong NVM for WCN6855 GF variant without board ID
Bluetooth: hci_dev: replace 'quirks' integer by 'quirk_flags' bitmap
Bluetooth: hci_core: add missing braces when using macro parameters
Bluetooth: hci_core: fix typos in macros
Bluetooth: SMP: Fix using HCI_ERROR_REMOTE_USER_TERM on timeout
Bluetooth: SMP: If an unallowed command is received consider it a failure
Bluetooth: btintel: Check if controller is ISO capable on btintel_classify_pkt_type
Bluetooth: hci_sync: fix connectable extended advertising when using static random address
Bluetooth: Fix null-ptr-deref in l2cap_sock_resume_cb()
====================
Link: https://patch.msgid.link/20250717142849.537425-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Howells says:
====================
rxrpc: Miscellaneous fixes
Here are some fixes for rxrpc:
(1) Fix the calling of IP routing code with IRQs disabled.
(2) Fix a recvmsg/recvmsg race when the first completes a call.
(3) Fix a race between notification, recvmsg and sendmsg releasing a call.
(4) Fix abort of abort.
(5) Fix call-level aborts that should be connection-level aborts.
====================
Link: https://patch.msgid.link/20250717074350.3767366-1-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a call is released, rxrpc takes the spinlock and removes it from
->recvmsg_q in an effort to prevent racing recvmsg() invocations from
seeing the same call. Now, rxrpc_recvmsg() only takes the spinlock when
actually removing a call from the queue; it doesn't, however, take it in
the lead up to that when it checks to see if the queue is empty. It *does*
hold the socket lock, which prevents a recvmsg/recvmsg race - but this
doesn't prevent sendmsg from ending the call because sendmsg() drops the
socket lock and relies on the call->user_mutex.
Fix this by firstly removing the bit in rxrpc_release_call() that dequeues
the released call and, instead, rely on recvmsg() to simply discard
released calls (done in a preceding fix).
Secondly, rxrpc_notify_socket() is abandoned if the call is already marked
as released rather than trying to be clever by setting both pointers in
call->recvmsg_link to NULL to trick list_empty(). This isn't perfect and
can still race, resulting in a released call on the queue, but recvmsg()
will now clean that up.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-4-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a call receives an event (such as incoming data), the call gets placed
on the socket's queue and a thread in recvmsg can be awakened to go and
process it. Once the thread has picked up the call off of the queue,
further events will cause it to be requeued, and once the socket lock is
dropped (recvmsg uses call->user_mutex to allow the socket to be used in
parallel), a second thread can come in and its recvmsg can pop the call off
the socket queue again.
In such a case, the first thread will be receiving stuff from the call and
the second thread will be blocked on call->user_mutex. The first thread
can, at this point, process both the event that it picked call for and the
event that the second thread picked the call for and may see the call
terminate - in which case the call will be "released", decoupling the call
from the user call ID assigned to it (RXRPC_USER_CALL_ID in the control
message).
The first thread will return okay, but then the second thread will wake up
holding the user_mutex and, if it sees that the call has been released by
the first thread, it will BUG thusly:
kernel BUG at net/rxrpc/recvmsg.c:474!
Fix this by just dequeuing the call and ignoring it if it is seen to be
already released. We can't tell userspace about it anyway as the user call
ID has become stale.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Reported-by: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-3-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rxrpc_assess_MTU_size() function calls down into the IP layer to find
out the MTU size for a route. When accepting an incoming call, this is
called from rxrpc_new_incoming_call() which holds interrupts disabled
across the code that calls down to it. Unfortunately, the IP layer uses
local_bh_enable() which, config dependent, throws a warning if IRQs are
enabled:
WARNING: CPU: 1 PID: 5544 at kernel/softirq.c:387 __local_bh_enable_ip+0x43/0xd0
...
RIP: 0010:__local_bh_enable_ip+0x43/0xd0
...
Call Trace:
<TASK>
rt_cache_route+0x7e/0xa0
rt_set_nexthop.isra.0+0x3b3/0x3f0
__mkroute_output+0x43a/0x460
ip_route_output_key_hash+0xf7/0x140
ip_route_output_flow+0x1b/0x90
rxrpc_assess_MTU_size.isra.0+0x2a0/0x590
rxrpc_new_incoming_peer+0x46/0x120
rxrpc_alloc_incoming_call+0x1b1/0x400
rxrpc_new_incoming_call+0x1da/0x5e0
rxrpc_input_packet+0x827/0x900
rxrpc_io_thread+0x403/0xb60
kthread+0x2f7/0x310
ret_from_fork+0x2a/0x230
ret_from_fork_asm+0x1a/0x30
...
hardirqs last enabled at (23): _raw_spin_unlock_irq+0x24/0x50
hardirqs last disabled at (24): _raw_read_lock_irq+0x17/0x70
softirqs last enabled at (0): copy_process+0xc61/0x2730
softirqs last disabled at (25): rt_add_uncached_list+0x3c/0x90
Fix this by moving the call to rxrpc_assess_MTU_size() out of
rxrpc_init_peer() and further up the stack where it can be done without
interrupts disabled.
It shouldn't be a problem for rxrpc_new_incoming_call() to do it after the
locks are dropped as pmtud is going to be performed by the I/O thread - and
we're in the I/O thread at this point.
Fixes: a2ea9a9072 ("rxrpc: Use irq-disabling spinlocks between app and I/O thread")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
htb_lookup_leaf has a BUG_ON that can trigger with the following:
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: htb default 1
tc class add dev lo parent 1: classid 1:1 htb rate 64bit
tc qdisc add dev lo parent 1:1 handle 2: netem
tc qdisc add dev lo parent 2:1 handle 3: blackhole
ping -I lo -c1 -W0.001 127.0.0.1
The root cause is the following:
1. htb_dequeue calls htb_dequeue_tree which calls the dequeue handler on
the selected leaf qdisc
2. netem_dequeue calls enqueue on the child qdisc
3. blackhole_enqueue drops the packet and returns a value that is not
just NET_XMIT_SUCCESS
4. Because of this, netem_dequeue calls qdisc_tree_reduce_backlog, and
since qlen is now 0, it calls htb_qlen_notify -> htb_deactivate ->
htb_deactiviate_prios -> htb_remove_class_from_row -> htb_safe_rb_erase
5. As this is the only class in the selected hprio rbtree,
__rb_change_child in __rb_erase_augmented sets the rb_root pointer to
NULL
6. Because blackhole_dequeue returns NULL, netem_dequeue returns NULL,
which causes htb_dequeue_tree to call htb_lookup_leaf with the same
hprio rbtree, and fail the BUG_ON
The function graph for this scenario is shown here:
0) | htb_enqueue() {
0) + 13.635 us | netem_enqueue();
0) 4.719 us | htb_activate_prios();
0) # 2249.199 us | }
0) | htb_dequeue() {
0) 2.355 us | htb_lookup_leaf();
0) | netem_dequeue() {
0) + 11.061 us | blackhole_enqueue();
0) | qdisc_tree_reduce_backlog() {
0) | qdisc_lookup_rcu() {
0) 1.873 us | qdisc_match_from_root();
0) 6.292 us | }
0) 1.894 us | htb_search();
0) | htb_qlen_notify() {
0) 2.655 us | htb_deactivate_prios();
0) 6.933 us | }
0) + 25.227 us | }
0) 1.983 us | blackhole_dequeue();
0) + 86.553 us | }
0) # 2932.761 us | qdisc_warn_nonwc();
0) | htb_lookup_leaf() {
0) | BUG_ON();
------------------------------------------
The full original bug report can be seen here [1].
We can fix this just by returning NULL instead of the BUG_ON,
as htb_dequeue_tree returns NULL when htb_lookup_leaf returns
NULL.
[1] https://lore.kernel.org/netdev/pF5XOOIim0IuEfhI-SOxTgRvNoDwuux7UHKnE_Y5-zVd4wmGvNk2ceHjKb8ORnzw0cGwfmVu42g9dL7XyJLf1NEzaztboTWcm0Ogxuojoeo=@willsroot.io/
Fixes: 512bb43eb5 ("pkt_sched: sch_htb: Optimize WARN_ONs in htb_dequeue_tree() etc.")
Signed-off-by: William Liu <will@willsroot.io>
Signed-off-by: Savino Dicanosa <savy@syst3mfailure.io>
Link: https://patch.msgid.link/20250717022816.221364-1-will@willsroot.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
