Fix return value in RSB bus driver
* tag 'sunxi-fixes-for-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
Link: https://lore.kernel.org/r/Ymbkd+/dDmRJz66w@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit 1a67653de0, which caused a boot regression.
The behavior of the "drive-push-pull" in the kernel does not
match what the binding document describes. Revert Rob's patch
to make the DT match the kernel again, rather than the binding.
Link: https://lore.kernel.org/lkml/YlVAy95eF%2F9b1nmu@orome/
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ROHM BD71847 PMIC has a 32.768 kHz clock.
Describe the PMIC clock to fix the following boot errors:
bd718xx-clk bd71847-clk.1.auto: No parent clk found
bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Based on the same fix done for imx8mm-evk as per commit
a6a355ede5 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Fixes: 3e44dd0973 ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
Fixes: c2e4987e0e ("ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes for omaps
Few regression fixes for omap variants. These mostly fix issues related to
warnings added for system suspend, and some devicetree issues:
- Make ti-sysc driver quirks for gpt12 timer omap3 specific to fix
timer clock disabling for am335x system suspend
- Fix new system suspend warning for dra7 vpe caused by trying to
use register bits not wired for vpe
- Fix mmc boot order for omap3-gta04 that has no mmc2 or 3 wired
- Add missing touchscreen properties for am3
- Fix pin muxing for logicpd-som-lv and am3517-evm to not depend on
earlier bootloader versions
- Fix refcount leak for omap_gic_of_init
* tag 'omap-for-v5.18/fixes-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
ARM: dts: am3517-evm: Fix misc pinmuxing
ARM: dts: am33xx-l4: Add missing touchscreen clock properties
ARM: dts: Fix mmc order for omap3-gta04
ARM: dts: dra7: Fix suspend warning for vpe powerdomain
bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific
ARM: OMAP2+: Fix refcount leak in omap_gic_of_init
iommu/omap: Fix regression in probe for NULL pointer dereference
Link: https://lore.kernel.org/r/pull-1650543308-836725@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
HyperFlash devices fail to probe:
rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed
In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits
(SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
from half of the transfer size, cfr. the rpcif_bits_set() helper
function. However, rpcif_reg_{read,write}() does not take the bus size
into account, and does not double all Manual Mode Data Register access
sizes when communicating with a HyperFlash or Octal-SPI Flash device.
Fix this, and avoid the back-and-forth conversion between transfer size
and Transfer Data Enable bits, by explicitly storing the transfer size
in struct rpcif, and using that value to determine access size in
rpcif_reg_{read,write}().
Enforce that the "high" Manual Mode Read/Write Data Registers
(SM[RW]DR1) are only used for 8-byte data accesses.
While at it, forbid writing to the Manual Mode Read Data Registers,
as they are read-only.
Fixes: fff53a551d ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/cde9bfacf704c81865f57b15d1b48a4793da4286.1649681476.git.geert+renesas@glider.be
Link: https://lore.kernel.org/r/20220420070526.9367-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AT91 fixes#1 for 5.18:
Only DT fixes. They cover syntax issues as well as features:
- fix dtschema check warnings for DMA channel entries, boolean
properties and flash names
- sam9g20ek audio clock and regulator description
- sama5d[34]_xplained SPI pinctrl
- align DT with hardware subtleties on sama7g5ek
* tag 'at91-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: fix pinctrl phandles
ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
ARM: dts: at91: Describe regulators on at91sam9g20ek
ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
ARM: dts: at91: Fix boolean properties with values
ARM: dts: at91: use generic node name for dataflash
ARM: dts: at91: align SPI NOR node name with dtschema
ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
ARM: dts: at91: sama7g5: Swap `rx` and `tx` for `i2c` nodes
Link: https://lore.kernel.org/r/20220414143318.26363-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Gemini defconfig needs to be updated due to DSA driver
Kconfig changes in the v5.18 merge window:
CONFIG_NET_DSA_REALTEK_SMI is now behind
CONFIG_NET_DSA_REALTEK and the desired DSA switch need
to be selected explicitly with
CONFIG_NET_DSA_REALTEK_RTL8366RB.
Take this opportunity to update some other minor config
options:
- CONFIG_MARVELL_PHY moved around because of Kconfig
changes.
- CONFIG_SENSORS_DRIVETEMP should be selected since is
regulates the system critical alert temperature on
some devices, which is nice if it is handled even
if initramfs or root fails to mount.
Fixes: 319a70a5fe ("net: dsa: realtek-smi: move to subdirectory")
Fixes: 765c39a4fa ("net: dsa: realtek: convert subdrivers into modules")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Defconfig updates for kernel v5.18:
- Refresh defconfig with new and moved options
- Add some new hardware drivers
- Activate battery charging
* tag 'ux500-defconfig-soc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: config: u8500: Re-enable AB8500 battery charging
ARM: config: u8500: Add some common hardware
ARM: config: Refresh U8500 defconfig
Link: https://lore.kernel.org/r/CACRpkdY+_Go4XNzOh+Rvc24QBnUud2k-S7VQuaH5d-j71_dJog@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff71 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bootloader for the AM3517 has previously done much of the pin
muxing, but as the bootloader is moving more and more to a model
based on the device tree, it may no longer automatically mux the
pins, so it is necessary to add the pinmuxing to the Linux device
trees so the respective peripherals can remain functional.
Fixes: 6ed1d79975 ("ARM: dts: am3517-evm: Add support for UI board and Audio")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220226214820.747847-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When adding support for TI magadc (Magnetic Stripe Reader and ADC), the
MFD driver common to the touchscreen and the ADC got updated to ease the
insertion of a new DT node for the ADC, with its own compatible, clocks,
etc. Commit 235a96e92c ("mfd: ti_am335x_tscadc: Don't search the tree
for our clock") removed one compatible specific information which was
the clock name, because the clock was looked up from scratch in the DT
while this hardware block was only fed by a single clock, already
defined and properly filled in the DT.
Problem is, this change was only validated with an am437x-based board,
where the clocks are effectively correctly defined and referenced. But
on am33xx, the ADC clock is also correctly defined but is not referenced
with a clock phandle as it ought to be.
The touchscreen bindings clearly state that the clocks/clock-names
properties are mandatory, but they have been forgotten in one DTSI. This
was probably not noticed in the first place because of the clock
actually existing and the clk_get() call going through all the tree
anyway.
Add the missing clock phandles in the am33xx touchscreen description.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Fixes: 235a96e92c ("mfd: ti_am335x_tscadc: Don't search the tree for our clock")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Message-Id: <20220314163445.79807-1-miquel.raynal@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit bf781869e5 ("ARM: dts: at91: add pinctrl-{names, 0} for all
gpios") introduces pinctrl phandles for pins used by individual
controllers to avoid failures due to commit 2ab73c6d83 ("gpio:
Support GPIO controllers without pin-ranges"). For SPI controllers
available on SAMA5D4 and SAMA5D3 some of the pins are defined in
SoC specific dtsi on behalf of pinctrl-0. Adding extra pinctrl phandles
on board specific dts also on behalf of pinctrl-0 overwrite the pinctrl-0
phandle specified in SoC specific dtsi. Thus add the board specific
pinctrl to pinctrl-1.
Fixes: bf781869e5 ("ARM: dts: at91: add pinctrl-{names, 0} for all gpios")
Depends-on: 5c8b498529 ("ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name")
Reported-by: Ajay Kathat <ajay.kathat@microchip.com>
Co-developed-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Ajay Kathat <ajay.kathat@microchip.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220331141323.194355-2-claudiu.beznea@microchip.com
The MCLK of the WM8731 on the AT91SAM9G20-EK board is connected to the
PCK0 output of the SoC and is expected to be set to 12MHz. Previously
this was mapped using pre-common clock API calls in the audio machine
driver but the conversion to the common clock framework broke that so
describe things in the DT instead.
Fixes: ff78a189b0 ("ARM: at91: remove old at91-specific clock driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220404102806.581374-2-broonie@kernel.org
We currently are getting the following warning after a system suspend:
Powerdomain (vpe_pwrdm) didn't enter target state 0
Looks like this is because the STANDBYMODE bit for SMART_IDLE should
not be used. The TRM "Table 12-348. VPE_SYSCONFIG" says that the value
for SMART_IDLE is "0x2: Same behavior as bit-field value of 0x1". But
if the SMART_IDLE value is used, PM_VPE_PWRSTST LASTPOWERSTATEENTERED
bits always show value of 3.
Let's fix the issue by dropping SMART_IDLE for vpe. And let's also add
the missing the powerdomain for vpe.
Fixes: 1a20951605 ("ARM: dts: dra7: Add ti-sysc node for VPE")
Cc: Benoit Parrot <bparrot@ti.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On beagleboard revisions A to B4 we need to use gpt12 as the system timer.
However, the quirk handling added for gpt12 caused a regression for system
suspend for am335x as the PM coprocessor needs the timers idled for
suspend.
Let's make the gpt12 quirk specific to omap34xx, other SoCs don't need
it. Beagleboard revisions C and later no longer need to use the gpt12
related quirk. Then at some point, if we decide to drop support for the old
beagleboard revisions A to B4, we can also drop the gpt12 related quirks
completely.
Fixes: 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: fd1c078614 ("ARM: OMAP4: Fix the init code to have OMAP4460 errata available in DT build")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220309104302.18398-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The labels for lines 61 through 84 on the periphs-banks were offset by 2.
2 lines are missing in the BOOT GPIO lines (contains 14, should be 16)
Added 2 empty entries in BOOT to realigned the rest of GPIO labels
to match the Banana Pi M5 schematics.
(Thanks to Neil Armstrong for the heads up on the position of the missing pins)
Fixes: 976e920183 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Signed-off-by: Guillaume Giraudon <ggiraudon@prism19.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220411144427.874-1-ggiraudon@prism19.com
The sparse tool complains as follows:
drivers/bus/imx-weim.c:373:23: warning:
symbol 'weim_of_notifier' was not declared. Should it be static?
This symbol is not used outside of imx-weim.c, so marks it static.
Fixes: e6cb540828 ("bus: imx-weim: add DT overlay support for WEIM bus")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW71xx, GW72xx and GW73xx boards have USB1 routed to a USB OTG
connectors and USB2 routed to a USB hub.
The OTG connector has a over-currently protection with an active-low
pin and the USB1 to HUB connection has no over-current protection (as
the HUB itself implements this for its downstream ports).
Add proper dt nodes to specify the over-current pin polarity for USB1
and disable over-current protection for USB2.
Fixes: 6f30b27c5e ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes the qspi read command by importing the changes from commit
04aa946d57 ("arm64: dts: imx8: change the spi-nor tx").
Fixes: b186b8b6e7 ("arm64: dts: freescale: add initial device tree for TQMa8Mx with i.MX8M")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mn clock list for the ISI lists four clocks, but DOMAIN_MAX_CLKS
was set to 3. Because of this, attempts to enable the fourth clock failed,
threw some splat, and ultimately hung.
Fixes: 7f511d514e ("soc: imx: imx8m-blk-ctrl: add i.MX8MN DISP blk-ctrl")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fsl,scu.txt dt-binding documentation explicitly mentions
that the compatible string should be either "fsl,imx8qm-clock"
or "fsl,imx8qxp-clock", followed by "fsl,scu-clk". Also, i.MX8qm
SCU clocks and i.MX8qxp SCU clocks are really not the same, so
we have to set the compatible property according to SoC name.
Let's correct the i.MX8qm clock controller's compatible property
from
"fsl,imx8qxp-clk", "fsl,scu-clk"
to
"fsl,imx8qm-clk", "fsl,scu-clk" .
Fixes: f2180be18a ("arm64: dts: imx: add imx8qm common dts file")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 3f6634d997 ("iommu: Use right way to retrieve iommu_ops") started
triggering a NULL pointer dereference for some omap variants:
__iommu_probe_device from probe_iommu_group+0x2c/0x38
probe_iommu_group from bus_for_each_dev+0x74/0xbc
bus_for_each_dev from bus_iommu_probe+0x34/0x2e8
bus_iommu_probe from bus_set_iommu+0x80/0xc8
bus_set_iommu from omap_iommu_init+0x88/0xcc
omap_iommu_init from do_one_initcall+0x44/0x24
This is caused by omap iommu probe returning 0 instead of ERR_PTR(-ENODEV)
as noted by Jason Gunthorpe <jgg@ziepe.ca>.
Looks like the regression already happened with an earlier commit
6785eb9105 ("iommu/omap: Convert to probe/release_device() call-backs")
that changed the function return type and missed converting one place.
Cc: Drew Fustini <dfustini@baylibre.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Suman Anna <s-anna@ti.com>
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Fixes: 6785eb9105 ("iommu/omap: Convert to probe/release_device() call-backs")
Fixes: 3f6634d997 ("iommu: Use right way to retrieve iommu_ops")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Drew Fustini <dfustini@baylibre.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20220331062301.24269-1-tony@atomide.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reset controller fixes for v5.18
Document the deprecated 'hisi,rst-syscon' device tree property for
hisilicon,hi3660-reset, add an error check to reset deassertion in
reset-rzg2l-usbphy-ctrl, restore transfer error handling in Tegra
reset-bpmp, and document the optional 'resets' device tree property
for socionext,uniphier-reset.
* tag 'reset-fixes-for-v5.18' of git://git.pengutronix.de/pza/linux:
dt-bindings: reset: Add parent "resets" property as optional
reset: tegra-bpmp: Restore Handle errors in BPMP response
reset: renesas: Check return value of reset_control_deassert()
dt-bindings: reset: document deprecated HiSilicon property
Link: https://lore.kernel.org/r/20220406153337.1265414-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3m92Sj26/v1mLG@robh.at.kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
