Marc Kleine-Budde says:
====================
pull-request: can-next 2025-11-12
this is a pull request of 11 patches for net-next/main.
The first 3 patches are by Vadim Fedorenko and convert the CAN drivers
to use the ndo_hwtstamp callbacks.
Maud Spierings contributes a patch for the mcp251x driver that
converts it to use dev_err_probe().
The next 6 patches target the mcp251xfd driver and are by Gregor
Herburger and me. They add GPIO controller functionality to the
driver.
The final patch is by Chu Guangqing and fixes a typo in the bxcan
driver.
linux-can-next-for-6.19-20251112-2
* tag 'linux-can-next-for-6.19-20251112-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: bxcan: Fix a typo error for assign
dt-bindings: can: mcp251xfd: add gpio-controller property
can: mcp251xfd: add gpio functionality
can: mcp251xfd: only configure PIN1 when rx_int is set
can: mcp251xfd: add workaround for errata 5
can: mcp251xfd: utilize gather_write function for all non-CRC writes
can: mcp251xfd: move chip sleep mode into runtime pm
can: mcp251x: mcp251x_can_probe(): use dev_err_probe()
can: peak_usb: convert to use ndo_hwtstamp callbacks
can: peak_canfd: convert to use ndo_hwtstamp callbacks
can: convert generic HW timestamp ioctl to ndo_hwtstamp callbacks
====================
Link: https://patch.msgid.link/20251112184344.189863-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Extend the Lantiq GSWIP device tree binding to also cover MaxLinear
GSW1xx switches which are based on the same hardware IP but connected
via MDIO instead of being memory-mapped.
Add compatible strings for MaxLinear GSW120, GSW125, GSW140, GSW141,
and GSW145 switches and adjust the schema to handle the different
connection methods with conditional properties.
Add MaxLinear GSW125 example showing MDIO-connected configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/fc96f1dedb2b418a63e69960356dde7f6eb86424.1762170107.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for standard tx-internal-delay-ps and rx-internal-delay-ps
properties on port nodes to allow fine-tuning of RGMII clock delays.
The GSWIP switch hardware supports delay values in 500 picosecond
increments from 0 to 3500 picoseconds, with a post-reset default of 2000
picoseconds for both TX and RX delays. The driver currently sets the
delay to 0 in case the PHY is setup to carry out the delay by the
corresponding interface modes ("rgmii-id", "rgmii-rxid", "rgmii-txid").
This corresponds to the driver changes that allow adjusting MII delays
using Device Tree properties instead of relying solely on the PHY
interface mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/9e007d4f85c2c6d69e0b91f3663d99e0f6fc8eac.1762170107.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the TPS23881B I2C power sourcing equipment controller to the list of
supported devices.
Falling back to the TPS23881 predecessor device is not suitable as firmware
loading needs to handled differently by the driver. The TPS23881 and
TPS23881B devices require different firmware. Trying to load the TPS23881
firmware on a TPS23881B device fails and must therefore be omitted.
Signed-off-by: Thomas Wismer <thomas.wismer@scs.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20251029212312.108749-3-thomas@wismer.xyz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The pins associated with m_can have to have a special configuration to
be able to wakeup the SoC from some system states. This configuration is
described in the wakeup pinctrl state while the default state describes
the default configuration. Also add the sleep state which is already in
use by some devicetrees.
Also m_can can be a wakeup-source if capable of wakeup.
Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251001-topic-mcan-wakeup-source-v6-12-v10-1-4ab508ac5d1e@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking updates from Paolo Abeni:
"Core & protocols:
- Improve drop account scalability on NUMA hosts for RAW and UDP
sockets and the backlog, almost doubling the Pps capacity under DoS
- Optimize the UDP RX performance under stress, reducing contention,
revisiting the binary layout of the involved data structs and
implementing NUMA-aware locking. This improves UDP RX performance
by an additional 50%, even more under extreme conditions
- Add support for PSP encryption of TCP connections; this mechanism
has some similarities with IPsec and TLS, but offers superior HW
offloads capabilities
- Ongoing work to support Accurate ECN for TCP. AccECN allows more
than one congestion notification signal per RTT and is a building
block for Low Latency, Low Loss, and Scalable Throughput (L4S)
- Reorganize the TCP socket binary layout for data locality, reducing
the number of touched cachelines in the fastpath
- Refactor skb deferral free to better scale on large multi-NUMA
hosts, this improves TCP and UDP RX performances significantly on
such HW
- Increase the default socket memory buffer limits from 256K to 4M to
better fit modern link speeds
- Improve handling of setups with a large number of nexthop, making
dump operating scaling linearly and avoiding unneeded
synchronize_rcu() on delete
- Improve bridge handling of VLAN FDB, storing a single entry per
bridge instead of one entry per port; this makes the dump order of
magnitude faster on large switches
- Restore IP ID correctly for encapsulated packets at GSO
segmentation time, allowing GRO to merge packets in more scenarios
- Improve netfilter matching performance on large sets
- Improve MPTCP receive path performance by leveraging recently
introduced core infrastructure (skb deferral free) and adopting
recent TCP autotuning changes
- Allow bridges to redirect to a backup port when the bridge port is
administratively down
- Introduce MPTCP 'laminar' endpoint that con be used only once per
connection and simplify common MPTCP setups
- Add RCU safety to dst->dev, closing a lot of possible races
- A significant crypto library API for SCTP, MPTCP and IPv6 SR,
reducing code duplication
- Supports pulling data from an skb frag into the linear area of an
XDP buffer
Things we sprinkled into general kernel code:
- Generate netlink documentation from YAML using an integrated YAML
parser
Driver API:
- Support using IPv6 Flow Label in Rx hash computation and RSS queue
selection
- Introduce API for fetching the DMA device for a given queue,
allowing TCP zerocopy RX on more H/W setups
- Make XDP helpers compatible with unreadable memory, allowing more
easily building DevMem-enabled drivers with a unified XDP/skbs
datapath
- Add a new dedicated ethtool callback enabling drivers to provide
the number of RX rings directly, improving efficiency and clarity
in RX ring queries and RSS configuration
- Introduce a burst period for the health reporter, allowing better
handling of multiple errors due to the same root cause
- Support for DPLL phase offset exponential moving average,
controlling the average smoothing factor
Device drivers:
- Add a new Huawei driver for 3rd gen NIC (hinic3)
- Add a new SpacemiT driver for K1 ethernet MAC
- Add a generic abstraction for shared memory communication
devices (dibps)
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- Use multiple per-queue doorbell, to avoid MMIO contention
issues
- support adjacent functions, allowing them to delegate their
SR-IOV VFs to sibling PFs
- support RSS for IPSec offload
- support exposing raw cycle counters in PTP and mlx5
- support for disabling host PFs.
- Intel (100G, ice, idpf):
- ice: support for SRIOV VFs over an Active-Active link
aggregate
- ice: support for firmware logging via debugfs
- ice: support for Earliest TxTime First (ETF) hardware offload
- idpf: support basic XDP functionalities and XSk
- Broadcom (bnxt):
- support Hyper-V VF ID
- dynamic SRIOV resource allocations for RoCE
- Meta (fbnic):
- support queue API, zero-copy Rx and Tx
- support basic XDP functionalities
- devlink health support for FW crashes and OTP mem corruptions
- expand hardware stats coverage to FEC, PHY, and Pause
- Wangxun:
- support ethtool coalesce options
- support for multiple RSS contexts
- Ethernet virtual:
- Macsec:
- replace custom netlink attribute checks with policy-level
checks
- Bonding:
- support aggregator selection based on port priority
- Microsoft vNIC:
- use page pool fragments for RX buffers instead of full pages
to improve memory efficiency
- Ethernet NICs consumer, and embedded:
- Qualcomm: support Ethernet function for IPQ9574 SoC
- Airoha: implement wlan offloading via NPU
- Freescale
- enetc: add NETC timer PTP driver and add PTP support
- fec: enable the Jumbo frame support for i.MX8QM
- Renesas (R-Car S4):
- support HW offloading for layer 2 switching
- support for RZ/{T2H, N2H} SoCs
- Cadence (macb): support TAPRIO traffic scheduling
- TI:
- support for Gigabit ICSS ethernet SoC (icssm-prueth)
- Synopsys (stmmac): a lot of cleanups
- Ethernet PHYs:
- Support 10g-qxgmi phy-mode for AQR412C, Felix DSA and Lynx PCS
driver
- Support bcm63268 GPHY power control
- Support for Micrel lan8842 PHY and PTP
- Support for Aquantia AQR412 and AQR115
- CAN:
- a large CAN-XL preparation work
- reorganize raw_sock and uniqframe struct to minimize memory
usage
- rcar_canfd: update the CAN-FD handling
- WiFi:
- extended Neighbor Awareness Networking (NAN) support
- S1G channel representation cleanup
- improve S1G support
- WiFi drivers:
- Intel (iwlwifi):
- major refactor and cleanup
- Broadcom (brcm80211):
- support for AP isolation
- RealTek (rtw88/89) rtw88/89:
- preparation work for RTL8922DE support
- MediaTek (mt76):
- HW restart improvements
- MLO support
- Qualcomm/Atheros (ath10k):
- GTK rekey fixes
- Bluetooth drivers:
- btusb: support for several new IDs for MT7925
- btintel: support for BlazarIW core
- btintel_pcie: support for _suspend() / _resume()
- btintel_pcie: support for Scorpious, Panther Lake-H484 IDs"
* tag 'net-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1536 commits)
net: stmmac: Add support for Allwinner A523 GMAC200
dt-bindings: net: sun8i-emac: Add A523 GMAC200 compatible
Revert "Documentation: net: add flow control guide and document ethtool API"
octeontx2-pf: fix bitmap leak
octeontx2-vf: fix bitmap leak
net/mlx5e: Use extack in set rxfh callback
net/mlx5e: Introduce mlx5e_rss_params for RSS configuration
net/mlx5e: Introduce mlx5e_rss_init_params
net/mlx5e: Remove unused mdev param from RSS indir init
net/mlx5: Improve QoS error messages with actual depth values
net/mlx5e: Prevent entering switchdev mode with inconsistent netns
net/mlx5: HWS, Generalize complex matchers
net/mlx5: Improve write-combining test reliability for ARM64 Grace CPUs
selftests/net: add tcp_port_share to .gitignore
Revert "net/mlx5e: Update and set Xon/Xoff upon MTU set"
net: add NUMA awareness to skb_attempt_defer_free()
net: use llist for sd->defer_list
net: make softnet_data.defer_count an atomic
selftests: drv-net: psp: add tests for destroying devices
selftests: drv-net: psp: add test for auto-adjusting TCP MSS
...
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
Pull SoC dt updates from Arnd Bergmann:
"There are five sets of new SoCs that get added in existing families,
all of them being either upgrades or cut-down versions of the older
chips:
- Apple M2 Pro, M2 Max and M2 Ultra, used in the 2022/2023 generation
of high-end workstations and laptops from Apple. Linux has been
working on these for a while but stil requires patches.
- Axis Artpec8 is an Armv8 chip based on Samsung Exynos design,
unlike the earlier Armv7 Artpec6 from the same company that was
part of a separate family of chips.
- NXP i.MX91 is a cut-down version of i.MX93, using only a single
Cortex-A55 core.
- Qualcomm Lemans Auto is a variant of the Lemans SoC that was
originally merged under the sa8775p name, the differences being
mostly the firmware configuration of the platform.
- Four new Renesas SoCs RZ/T2H (r9a09g077m44), RZ/N2H (r9a09g087m44),
RZ/T2H (r9a09g077), and RZ/N2H (r9a09g087) are all industrial
bedded SoCs based on Cortex-A55 cores
In total, there are 65 new machines, including:
- Industrial embedded system and single-board computers based on NXP,
Allwinner, TI, Rockchips, Marvell, Xilinx Spacemit, Starfive chips.
- Reference boards for the newly added Renesas, Qualcomm, NXP and
Axis ARMv8 chips as well as Microchip's MPFS RISC-V SoC
- Laptops and Workstations using Apple M2 and Qualcomm Snapdragon X1
chips.
- Several Samsung phones using Qualcomm Snapdragon chips
- Set-top boxes based on Allwinner H313
- Five BMC boards using 32-bit ASpeed SoCs
- Three network routers using IXP4xx (ARMv5!) and Broadcom bcm4708
(ARMv7) SoCs
Two machines get phased out because they were available only in small
quantities but never made it into products: one STi407 based reference
board, and a Snapdragon 845 based Chromebook.
Aside from the newly added machines, a lot of work went into improving
hardware support on the existing machines and cleaning up contents for
validation"
* tag 'soc-dt-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (931 commits)
arm64: dts: apm-shadowcat: Drop "apm,xgene2-pcie" compatible
arm64: dts: apm-shadowcat: Move slimpro nodes out of "simple-bus" node
ARM: dts: microchip: sam9x7: Add qspi controller
arm64: dts: qcom: Add MST pixel streams for displayport
arm64: dts: qcom: sm6350: correct DP compatibility strings
arm64: dts: qcom: monaco-evk: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300-ride: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300: Add gpu and gmu nodes
arm64: dts: allwinner: h313: Add Amediatech X96Q
dt-bindings: arm: sunxi: Add Amediatech X96Q
arm64: dts: apple: t8015: Add SPMI node
arm64: dts: apple: t8012: Add SPMI node
arm64: dts: apple: Add J180d (Mac Pro, M2 Ultra, 2023) device tree
arm64: dts: rockchip: Add devicetree for the ROC-RK3588-RT
dt-bindings: arm: rockchip: Add Firefly ROC-RK3588-RT
arm64: dts: rockchip: update pinctrl names for Radxa E52C
arm64: dts: rockchip: remove vcc_3v3_pmu regulator for Radxa E52C
arm64: dts: apple: Add J474s, J475c and J475d device trees
arm64: dts: apple: Add J414 and J416 Macbook Pro device trees
arm64: dts: apple: Add initial t6020/t6021/t6022 DTs
...
Pull devicetree updates from Rob Herring:
"DT core:
- Update dtc to upstream version v1.7.2-35-g52f07dcca47c
- Add stub for of_get_next_child_with_prefix()
- Convert of_msi_map_id() callers to of_msi_xlate()
DT bindings:
- Convert multiple text board bindings to DT schema format
- Add bindings for synaptics,synaptics_i2c touchscreen controller,
innolux,n133hse-ea1 and nlt,nl12880bc20-spwg-24 displays, and NXP
vf610 reboot controller
- Add new Arm Cortex-A320/A520AE/A720AE and C1-Nano/Pro/Premium/Ultra
CPUs. Add missing Applied Micro CPU compatibles. Add pu-supply and
fsl,soc-operating-points properties for CPU nodes.
- Add QCom Glymur PDC and tegra264-agic interrupt controllers
- Add samsung,exynos8890-mali GPU to Arm Mali Midgard
- Drop Samsung S3C2410 display related bindings
- Allow separate DP lane and AUX connections in dp-connector
- Add some missing, undocumented vendor prefixes
- Add missing '#address-cells' properties in interrupt controller
bindings which dtc now warns about
- Drop duplicate socfpga-sdram-edac.txt, moxa,moxart-watchdog.txt,
fsl/mpic.txt, ti,opa362.txt, and cavium-thunder2.txt legacy text
bindings which are already covered by existing schemas.
- Various binding fixes for Mediatek platforms in mailbox, regulator,
pinctrl, timer, and display
- Drop work-around for yamllint quoting of values containing ','
- Various spelling, typo, grammar, and duplicated words fixes in DT
bindings and docs
- Add binding guidelines for defining properties at top level of
schemas, lack of node name ABI, and usage of simple-mfd"
* tag 'devicetree-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (81 commits)
dt-bindings: arm: altera: Drop socfpga-sdram-edac.txt
dt-bindings: gpu: Convert nvidia,gk20a to DT schema
dt-bindings: rng: sparc_sun_oracle_rng: convert to DT schema
dt-bindings: vendor-prefixes: update regex for properties without a prefix
dt-bindings: display: bridge: convert megachips-stdpxxxx-ge-b850v3-fw.txt to yaml
scripts: dt_to_config: fix grammar and a typo in --help text
dt-bindings: fix spelling, typos, grammar, duplicated words
docs: dt: fix grammar and spelling
of: base: Add of_get_next_child_with_prefix() stub
dt-bindings: trivial-devices: Add compatible string synaptics,synaptics_i2c
dt-bindings: soc: mediatek: pwrap: Add power-domains property
dt-bindings: pinctrl: mt65xx: Allow gpio-line-names
dt-bindings: media: Convert MediaTek mt8173-vpu bindings to DT schema
dt-bindings: arm: mediatek: Support mt8183-audiosys variant
dt-bindings: mailbox: mediatek,gce-mailbox: Make clock-names optional
dt-bindings: regulator: mediatek,mt6331: Add missing compatible
dt-bindings: regulator: mediatek,mt6331: Fix various regulator names
dt-bindings: regulator: mediatek,mt6332-regulator: Add missing compatible
dt-bindings: pinctrl: mediatek,mt7622-pinctrl: Add missing base reg
dt-bindings: pinctrl: mediatek,mt7622-pinctrl: Add missing pwm_ch7_2
...
Cross-merge networking fixes after downstream PR (net-6.17-rc8).
Conflicts:
tools/testing/selftests/drivers/net/bonding/Makefile
87951b5664 selftests: bonding: add test for passive LACP mode
c2377f1763 selftests: bonding: add test for LACP actor port priority
Adjacent changes:
drivers/net/ethernet/cadence/macb.h
fca3dc859b net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf16 net: macb: Add TAPRIO traffic scheduling support
drivers/net/ethernet/cadence/macb_main.c
fca3dc859b net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf16 net: macb: Add TAPRIO traffic scheduling support
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Allwinner A523 SoC family has a second Ethernet controller, called
the GMAC200 in the BSP and T527 datasheet, and referred to as GMAC1 for
numbering. This controller, according to BSP sources, is fully
compatible with a slightly newer version of the Synopsys DWMAC core.
The glue layer around the controller is the same as found around older
DWMAC cores on Allwinner SoCs. The only slight difference is that since
this is the second controller on the SoC, the register for the clock
delay controls is at a different offset. Last, the integration includes
a dedicated clock gate for the memory bus and the whole thing is put in
a separately controllable power domain.
Add a compatible string entry for it, and work in the requirements for
a second clock and a power domain.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://patch.msgid.link/20250925191600.3306595-2-wens@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Apple SoC driver updates for 6.18
Krzysztof Kozlowski asked us to move away from generic compatibles:
- Adjust all dt-bindings to use apple,t8103-XXXX instead of apple,XXXX
as fallback and add a comment that the old generic list should no
longer be extended.
- Add new fallback compatibles to pinctrl, pmdomain, spi, and mca
drivers. These changes have been Acked by their subsystem maintainers
to be merged through our tree together with the dt-bindings.
Support for pre-M1 Apple Silicon:
- SART and mailbox gain support for Apple's A11, which are both
required for NVMe.
- NVMe also gains support for Apple's A11 and the nvme maintainers
prefer that we merge this through the soc tree together with
the mailbox and SART changes.
- SPMI compatibles for A11 and T2 have been added, also going through
the soc tree due to conflicts with the generic compatible removal and
because no driver change is required.
Signed-off-by: Sven Peter <sven@kernel.org>
* tag 'apple-soc-drivers-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sven/linux: (32 commits)
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
spi: apple: Add "apple,t8103-spi" compatible
ASoC: apple: mca: Add "apple,t8103-mca" compatible
pinctrl: apple: Add "apple,t8103-pinctrl" as compatible
spi: dt-bindings: apple,spi: Add t6020-spi compatible
ASoC: dt-bindings: apple,mca: Add t6020-mca compatible
dt-bindings: dma: apple,admac: Add t6020-admac compatible
dt-bindings: clock: apple,nco: Add t6020-nco compatible
dt-bindings: watchdog: apple,wdt: Add t6020-wdt compatible
dt-bindings: spmi: apple,spmi: Add t6020-spmi compatible
dt-bindings: mfd: apple,smc: Add t6020-smc compatible
dt-bindings: net: bcm4329-fmac: Add BCM4388 PCI compatible
dt-bindings: net: bcm4377-bluetooth: Add BCM4388 compatible
dt-bindings: nvme: apple: Add apple,t6020-nvme-ans2 compatible
dt-bindings: iommu: apple,sart: Add apple,t6020-sart compatible
dt-bindings: gpu: apple,agx: Add agx-{g14s,g14c,g14d} compatibles
dt-bindings: mailbox: apple,mailbox: Add t6020 compatible
dt-bindings: pinctrl: apple,pinctrl: Add apple,t6020-pinctrl compatible
dt-bindings: iommu: dart: Add apple,t6020-dart compatible
...
Link: https://lore.kernel.org/r/20250920123028.49973-1-sven@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
At reset, KSZ8463 uses a strap-based configuration to set SPI as
interface bus. If the required pull-ups/pull-downs are missing (by
mistake or by design to save power) the pins may float and the
configuration can go wrong preventing any communication with the switch.
Add a 'reset' pinmux state
Add a KSZ8463 specific strap description that can be used by the driver
to drive the strap pins during reset. Two GPIOs are used. Users must
describe either both of them or none of them.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250918-ksz-strap-pins-v3-2-16662e881728@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add device tree binding support for RZ/T2H and RZ/N2H SoCs to the
existing RZ/N1 MIIC converter binding. These SoCs share similar MIIC
functionality but have architectural differences that require schema
updates.
Add new compatible strings "renesas,r9a09g077-miic" for RZ/T2H and
"renesas,r9a09g087-miic" for RZ/N2H, with the latter falling back to
the RZ/T2H variant. The new SoCs require reset support with two reset
lines for converter register reset and converter reset, which are not
present on RZ/N1.
Update port configurations to accommodate the different architectures.
RZ/N1 supports 5 ports numbered 1-5 with complex input mappings
covering indices 0-13, while RZ/T2H and RZ/N2H support 4 ports
numbered 0-3 with simplified input mappings covering indices 0-8.
Extend the switch port configuration property to support value 0 for
the new SoCs.
Add a new dt-bindings header file with media interface connection
matrix constants that map GMAC, ESC, and ETHSW ports to numeric
identifiers for use with RZ/T2H and RZ/N2H device trees.
Update DT schema validation to ensure proper port numbering and input
mappings per SoC variant.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250910204132.319975-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
STM32 DT for v6.18, round 1
Highlights:
----------
- MPU:
- STM32MP13:
- Add missing Ethernet1/2 PTP reference clocks.
- Add Hardware debug port (HDP).
- STMP32MP15:
- Add resets property to m_can nodes.
- Add Hardware debug port (HDP) and enable it on stm32mp157c-dk2
board.
- Reserve leds for CM4 on stm32mp15xx-ed1 and stm32mp15xx-dkx.
- stm32mp151c-plyaqm:
Use correct dai-format property.
- STM32MP23:
- Add Ethernet1 MAC controller on stm32mp235f-dk board:
It is connected to a RTL8211F-CG phy through RGMII.
- Fix GPIO bank definition & memory size (DDR).
- STM32MP25:
- Add Ethernet1 MAC controller on stm32mp257f-dk board.
It is connected to a RTL8211F-CG phy through RGMII.
- Add Ethernet1 MAC controller on stm32mp257f-ev1 board.
It is connected to a RTL8211F-CG phy through RGMII.
- Add display support by enabling the following IPs on
stm32mp257f-ev1:
* LTDC
* LVDS
* WSVGA LVDS panel (1024x600)
* Panel LVDS backlight as GPIO backlight
* ILI2511 i2c touchscreen
- Add PCIe Root complex and Endpoint support on stm32mp257f-ev1.
Root complex mode is used by default.
* tag 'stm32-dt-for-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (30 commits)
arm64: dts: st: fix memory region size on stm32mp235f-dk
arm64: dts: st: remove gpioj and gpiok banks from stm32mp231
arm64: dts: st: enable ethernet1 controller on stm32mp235f-dk
arm64: dts: st: enable ethernet1 controller on stm32mp257f-ev1
arm64: dts: st: enable ethernet1 controller on stm32mp257f-dk
arm64: dts: st: add eth1 pins for stm32mp2x platforms
ARM: dts: stm32: add missing PTP reference clocks on stm32mp13x SoCs
arm64: dts: st: enable display support on stm32mp257f-ev1 board
arm64: dts: st: add clock-cells to syscfg node on stm32mp251
arm64: dts: st: add lvds support on stm32mp255
arm64: dts: st: add ltdc support on stm32mp255
arm64: dts: st: add ltdc support on stm32mp251
ARM: dts: stm32: add resets property to m_can nodes in the stm32mp153
dt-binding: can: m_can: add optional resets property
arm64: dts: st: Enable PCIe on the stm32mp257f-ev1 board
arm64: dts: st: Add PCIe Endpoint mode on stm32mp251
arm64: dts: st: Add PCIe Root Complex mode on stm32mp251
arm64: dts: st: add PCIe pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: defconfig: Enable STMicroelectronics STM32 DMA3 support
ARM: dts: stm32: add Hardware debug port (HDP) on stm32mp157c-dk2 board
...
Link: https://lore.kernel.org/r/13153fc2-1abe-4d53-807a-5d289981a63d@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BCM4388 WiFi/BT modules are found on Apple silicon devices using
M2 Pro/Max/Ultra and later. Driver support for this module is not
submitted yet.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Janne Grunau <j@jannau.net>
