Merge tag 'soc-dt-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC dt updates from Arnd Bergmann: "There are five sets of new SoCs that get added in existing families, all of them being either upgrades or cut-down versions of the older chips: - Apple M2 Pro, M2 Max and M2 Ultra, used in the 2022/2023 generation of high-end workstations and laptops from Apple. Linux has been working on these for a while but stil requires patches. - Axis Artpec8 is an Armv8 chip based on Samsung Exynos design, unlike the earlier Armv7 Artpec6 from the same company that was part of a separate family of chips. - NXP i.MX91 is a cut-down version of i.MX93, using only a single Cortex-A55 core. - Qualcomm Lemans Auto is a variant of the Lemans SoC that was originally merged under the sa8775p name, the differences being mostly the firmware configuration of the platform. - Four new Renesas SoCs RZ/T2H (r9a09g077m44), RZ/N2H (r9a09g087m44), RZ/T2H (r9a09g077), and RZ/N2H (r9a09g087) are all industrial bedded SoCs based on Cortex-A55 cores In total, there are 65 new machines, including: - Industrial embedded system and single-board computers based on NXP, Allwinner, TI, Rockchips, Marvell, Xilinx Spacemit, Starfive chips. - Reference boards for the newly added Renesas, Qualcomm, NXP and Axis ARMv8 chips as well as Microchip's MPFS RISC-V SoC - Laptops and Workstations using Apple M2 and Qualcomm Snapdragon X1 chips. - Several Samsung phones using Qualcomm Snapdragon chips - Set-top boxes based on Allwinner H313 - Five BMC boards using 32-bit ASpeed SoCs - Three network routers using IXP4xx (ARMv5!) and Broadcom bcm4708 (ARMv7) SoCs Two machines get phased out because they were available only in small quantities but never made it into products: one STi407 based reference board, and a Snapdragon 845 based Chromebook. Aside from the newly added machines, a lot of work went into improving hardware support on the existing machines and cleaning up contents for validation" * tag 'soc-dt-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (931 commits) arm64: dts: apm-shadowcat: Drop "apm,xgene2-pcie" compatible arm64: dts: apm-shadowcat: Move slimpro nodes out of "simple-bus" node ARM: dts: microchip: sam9x7: Add qspi controller arm64: dts: qcom: Add MST pixel streams for displayport arm64: dts: qcom: sm6350: correct DP compatibility strings arm64: dts: qcom: monaco-evk: Enable Adreno 623 GPU arm64: dts: qcom: qcs8300-ride: Enable Adreno 623 GPU arm64: dts: qcom: qcs8300: Add gpu and gmu nodes arm64: dts: allwinner: h313: Add Amediatech X96Q dt-bindings: arm: sunxi: Add Amediatech X96Q arm64: dts: apple: t8015: Add SPMI node arm64: dts: apple: t8012: Add SPMI node arm64: dts: apple: Add J180d (Mac Pro, M2 Ultra, 2023) device tree arm64: dts: rockchip: Add devicetree for the ROC-RK3588-RT dt-bindings: arm: rockchip: Add Firefly ROC-RK3588-RT arm64: dts: rockchip: update pinctrl names for Radxa E52C arm64: dts: rockchip: remove vcc_3v3_pmu regulator for Radxa E52C arm64: dts: apple: Add J474s, J475c and J475d device trees arm64: dts: apple: Add J414 and J416 Macbook Pro device trees arm64: dts: apple: Add initial t6020/t6021/t6022 DTs ...
2025-12-27 11:06:41 -05:00 · 2025-10-01 17:19:38 -07:00
parent a8253f8077 8c0650e0ce
commit 0f048c878e
847 changed files with 59980 additions and 16384 deletions
--- a/Documentation/devicetree/bindings/arm/apple.yaml
+++ b/Documentation/devicetree/bindings/arm/apple.yaml
@@ -92,10 +92,11 @@ description: |
  Devices based on the "M2" SoC:

  - MacBook Air (M2, 2022)
+  - MacBook Air (15-inch, M2, 2023)
  - MacBook Pro (13-inch, M2, 2022)
  - Mac mini (M2, 2023)

-  And devices based on the "M1 Pro", "M1 Max" and "M1 Ultra" SoCs:
+  Devices based on the "M1 Pro", "M1 Max" and "M1 Ultra" SoCs:

  - MacBook Pro (14-inch, M1 Pro, 2021)
  - MacBook Pro (14-inch, M1 Max, 2021)
@@ -104,6 +105,17 @@ description: |
  - Mac Studio (M1 Max, 2022)
  - Mac Studio (M1 Ultra, 2022)

+  Devices based on the "M2 Pro", "M2 Max" and "M2 Ultra" SoCs:
+
+  - MacBook Pro (14-inch, M2 Pro, 2023)
+  - MacBook Pro (14-inch, M2 Max, 2023)
+  - MacBook Pro (16-inch, M2 Pro, 2023)
+  - MacBook Pro (16-inch, M2 Max, 2023)
+  - Mac mini (M2 Pro, 2023)
+  - Mac Studio (M2 Max, 2023)
+  - Mac Studio (M2 Ultra, 2023)
+  - Mac Pro (M2 Ultra, 2023)
+
  The compatible property should follow this format:

  compatible = "apple,<targettype>", "apple,<socid>", "apple,arm-platform";
@@ -279,6 +291,7 @@ properties:
        items:
          - enum:
              - apple,j413 # MacBook Air (M2, 2022)
+              - apple,j415 # MacBook Air (15-inch, M2, 2023)
              - apple,j473 # Mac mini (M2, 2023)
              - apple,j493 # MacBook Pro (13-inch, M2, 2022)
          - const: apple,t8112
@@ -308,6 +321,32 @@ properties:
          - const: apple,t6002
          - const: apple,arm-platform

+      - description: Apple M2 Pro SoC based platforms
+        items:
+          - enum:
+              - apple,j414s # MacBook Pro (14-inch, M2 Pro, 2023)
+              - apple,j416s # MacBook Pro (16-inch, M2 Pro, 2023)
+              - apple,j474s # Mac mini (M2 Pro, 2023)
+          - const: apple,t6020
+          - const: apple,arm-platform
+
+      - description: Apple M2 Max SoC based platforms
+        items:
+          - enum:
+              - apple,j414c # MacBook Pro (14-inch, M2 Max, 2023)
+              - apple,j416c # MacBook Pro (16-inch, M2 Max, 2023)
+              - apple,j475c # Mac Studio (M2 Max, 2023)
+          - const: apple,t6021
+          - const: apple,arm-platform
+
+      - description: Apple M2 Ultra SoC based platforms
+        items:
+          - enum:
+              - apple,j180d # Mac Pro (M2 Ultra, 2023)
+              - apple,j475d # Mac Studio (M2 Ultra, 2023)
+          - const: apple,t6022
+          - const: apple,arm-platform
+
 additionalProperties: true

 ...
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -46,6 +46,7 @@ properties:
              - facebook,yamp-bmc
              - facebook,yosemitev2-bmc
              - facebook,wedge400-bmc
+              - facebook,wedge400-data64-bmc
              - hxt,stardragon4800-rep2-bmc
              - ibm,mihawk-bmc
              - ibm,mowgli-bmc
@@ -81,9 +82,12 @@ properties:
              - asus,x4tf-bmc
              - facebook,bletchley-bmc
              - facebook,catalina-bmc
+              - facebook,clemente-bmc
              - facebook,cloudripper-bmc
+              - facebook,darwin-bmc
              - facebook,elbert-bmc
              - facebook,fuji-bmc
+              - facebook,fuji-data64-bmc
              - facebook,greatlakes-bmc
              - facebook,harma-bmc
              - facebook,minerva-cmc
--- a/Documentation/devicetree/bindings/arm/axis.txt
+++ b/Documentation/devicetree/bindings/arm/axis.txt
@@ -1,13 +0,0 @@
-Axis Communications AB
-ARTPEC series SoC Device Tree Bindings
-
-ARTPEC-6 ARM SoC
-================
-
-Required root node properties:
- compatible = "axis,artpec6";
-
-ARTPEC-6 Development board:
---------------------------
-Required root node properties:
- compatible = "axis,artpec6-dev-board", "axis,artpec6";
--- a/Documentation/devicetree/bindings/arm/axis.yaml
+++ b/Documentation/devicetree/bindings/arm/axis.yaml
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/axis.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Axis ARTPEC platforms
+
+maintainers:
+  - Jesper Nilsson <jesper.nilsson@axis.com>
+  - Lars Persson <lars.persson@axis.com>
+  - linux-arm-kernel@axis.com
+
+description: |
+  ARM platforms using SoCs designed by Axis branded as "ARTPEC".
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - description: Axis ARTPEC-6 SoC board
+        items:
+          - enum:
+              - axis,artpec6-dev-board
+          - const: axis,artpec6
+
+      - description: Axis ARTPEC-8 SoC board
+        items:
+          - enum:
+              - axis,artpec8-grizzly
+          - const: axis,artpec8
+
+additionalProperties: true
+
+...
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.yaml
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.yaml
@@ -25,6 +25,7 @@ properties:
          - enum:
              - asus,rt-ac56u
              - asus,rt-ac68u
+              - buffalo,wxr-1750dhp
              - buffalo,wzr-1166dhp
              - buffalo,wzr-1166dhp2
              - buffalo,wzr-1750dhp
--- a/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-pm.yaml
+++ b/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-pm.yaml
@@ -28,6 +28,14 @@ properties:
  reg:
    maxItems: 1

+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: divcore
+      - const: hsrun_divcore
+
 required:
  - compatible
  - reg
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1112,6 +1112,7 @@ properties:
              - skov,imx8mp-skov-revb-mi1010ait-1cp1 # SKOV i.MX8MP climate control with 10.1" panel
              - skov,imx8mp-skov-revc-bd500 # SKOV i.MX8MP climate control with LED frontplate
              - skov,imx8mp-skov-revc-tian-g07017 # SKOV i.MX8MP climate control with 7" panel
+              - ultratronik,imx8mp-ultra-mach-sbc # Ultratronik SBC i.MX8MP based board
              - ysoft,imx8mp-iota2-lumpy  # Y Soft i.MX8MP IOTA2 Lumpy Board
          - const: fsl,imx8mp

@@ -1200,6 +1201,24 @@ properties:
          - const: polyhex,imx8mp-debix-som-a       # Polyhex Debix SOM A
          - const: fsl,imx8mp

+      - description: SolidRun i.MX8MP SoM based boards
+        items:
+          - enum:
+              - solidrun,imx8mp-cubox-m             # SolidRun i.MX8MP SoM on CuBox-M
+              - solidrun,imx8mp-hummingboard-mate   # SolidRun i.MX8MP SoM on HummingBoard Mate
+              - solidrun,imx8mp-hummingboard-pro    # SolidRun i.MX8MP SoM on HummingBoard Pro
+              - solidrun,imx8mp-hummingboard-pulse  # SolidRun i.MX8MP SoM on HummingBoard Pulse
+              - solidrun,imx8mp-hummingboard-ripple # SolidRun i.MX8MP SoM on HummingBoard Ripple
+          - const: solidrun,imx8mp-sr-som
+          - const: fsl,imx8mp
+
+      - description: TechNexion EDM-G-IMX8M-PLUS SoM based boards
+        items:
+          - enum:
+              - technexion,edm-g-imx8mp-wb          # TechNexion EDM-G-IMX8MP SOM on WB-EDM-G
+          - const: technexion,edm-g-imx8mp          # TechNexion EDM-G-IMX8MP SOM
+          - const: fsl,imx8mp
+
      - description: Toradex Boards with SMARC iMX8M Plus Modules
        items:
          - const: toradex,smarc-imx8mp-dev # Toradex SMARC iMX8M Plus on Toradex SMARC Development Board
@@ -1382,9 +1401,16 @@ properties:
      - description: i.MX8ULP based Boards
        items:
          - enum:
+              - fsl,imx8ulp-9x9-evk       # i.MX8ULP EVK9 Board
              - fsl,imx8ulp-evk           # i.MX8ULP EVK Board
          - const: fsl,imx8ulp

+      - description: i.MX91 based Boards
+        items:
+          - enum:
+              - fsl,imx91-11x11-evk       # i.MX91 11x11 EVK Board
+          - const: fsl,imx91
+
      - description: i.MX93 based Boards
        items:
          - enum:
@@ -1425,6 +1451,24 @@ properties:
              - fsl,imxrt1170-evk         # i.MXRT1170 EVK Board
          - const: fsl,imxrt1170

+      - description:
+          TQMa91xxLA and TQMa91xxCA are two series of feature compatible SOM
+          using NXP i.MX91 SOC in 11x11 mm package.
+          TQMa91xxLA is designed to be soldered on different carrier boards.
+          TQMa91xxCA is a compatible variant using board to board connectors.
+          All SOM and CPU variants use the same device tree hence only one
+          compatible is needed. Bootloader disables all features not present
+          in the assembled SOC.
+          MBa91xxCA mainboard can be used as starterkit for the SOM
+          soldered on an adapter board or for the connector variant
+          MBa91xxLA mainboard is a single board computer using the solderable
+          SOM variant
+        items:
+          - enum:
+              - tq,imx91-tqma9131-mba91xxca # TQ-Systems GmbH i.MX91 TQMa91xxCA/LA SOM on MBa91xxCA
+          - const: tq,imx91-tqma9131        # TQ-Systems GmbH i.MX91 TQMa91xxCA/LA SOM
+          - const: fsl,imx91
+
      - description:
          TQMa93xxLA and TQMa93xxCA are two series of feature compatible SOM
          using NXP i.MX93 SOC in 11x11 mm package.
@@ -1537,6 +1581,12 @@ properties:
              - fsl,ls1012a-qds
          - const: fsl,ls1012a

+      - description: TQ Systems TQMLS12AL SoM on MBLS1012AL board
+        items:
+          - const: tq,ls1012a-tqmls1012al-mbls1012al
+          - const: tq,ls1012a-tqmls1012al
+          - const: fsl,ls1012a
+
      - description: LS1021A based Boards
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/intel-ixp4xx.yaml
+++ b/Documentation/devicetree/bindings/arm/intel-ixp4xx.yaml
@@ -16,6 +16,8 @@ properties:
    oneOf:
      - items:
          - enum:
+              - actiontec,mi424wr-ac
+              - actiontec,mi424wr-d
              - adieng,coyote
              - arcom,vulcan
              - dlink,dsm-g600-a
--- a/Documentation/devicetree/bindings/arm/keystone/keystone.txt
+++ b/Documentation/devicetree/bindings/arm/keystone/keystone.txt
@@ -1,42 +0,0 @@
-TI Keystone Platforms Device Tree Bindings
-----------------------------------------------
-
-Boards with Keystone2 based devices (TCI66xxK2H) SOC shall have the
-following properties.
-
-Required properties:
- - compatible: All TI specific devices present in Keystone SOC should be in
-   the form "ti,keystone-*". Generic devices like gic, arch_timers, ns16550
-   type UART should use the specified compatible for those devices.
-
-SoC families:
-
- Keystone 2 generic SoC:
-   compatible = "ti,keystone"
-
-SoCs:
-
- Keystone 2 Hawking/Kepler
-   compatible = "ti,k2hk", "ti,keystone"
- Keystone 2 Lamarr
-   compatible = "ti,k2l", "ti,keystone"
- Keystone 2 Edison
-   compatible = "ti,k2e", "ti,keystone"
- K2G
-   compatible = "ti,k2g", "ti,keystone"
-
-Boards:
-  Keystone 2 Hawking/Kepler EVM
-   compatible = "ti,k2hk-evm", "ti,k2hk", "ti,keystone"
-
-  Keystone 2 Lamarr EVM
-   compatible = "ti,k2l-evm", "ti, k2l", "ti,keystone"
-
-  Keystone 2 Edison EVM
-   compatible = "ti,k2e-evm", "ti,k2e", "ti,keystone"
-
-  K2G EVM
-   compatible = "ti,k2g-evm", "ti,k2g", "ti-keystone"
-
-  K2G Industrial Communication Engine EVM
-   compatible = "ti,k2g-ice", "ti,k2g", "ti-keystone"
--- a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.yaml
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.yaml
@@ -23,6 +23,7 @@ properties:
              - marvell,armada-3720-db
              - methode,edpu
              - methode,udpu
+              - ripe,atlas-v5
          - const: marvell,armada3720
          - const: marvell,armada3710

--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -431,11 +431,13 @@ properties:
          - const: mediatek,mt8365
      - items:
          - enum:
+              - grinn,genio-510-sbc
              - mediatek,mt8370-evk
          - const: mediatek,mt8370
          - const: mediatek,mt8188
      - items:
          - enum:
+              - grinn,genio-700-sbc
              - mediatek,mt8390-evk
          - const: mediatek,mt8390
          - const: mediatek,mt8188
--- a/Documentation/devicetree/bindings/arm/nxp/lpc32xx.yaml
+++ b/Documentation/devicetree/bindings/arm/nxp/lpc32xx.yaml
@@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: NXP LPC32xx Platforms

 maintainers:
-  - Roland Stigge <stigge@antcom.de>
+  - Vladimir Zapolskiy <vz@mleia.com>

 properties:
  compatible:
--- a/Documentation/devicetree/bindings/arm/qcom-soc.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom-soc.yaml
@@ -23,7 +23,9 @@ description: |
 select:
  properties:
    compatible:
-      pattern: "^qcom,.*(apq|ipq|mdm|msm|qcm|qcs|q[dr]u|sa|sar|sc|sd[amx]|sm|x1[ep])[0-9]+.*$"
+      oneOf:
+        - pattern: "^qcom,.*(apq|ipq|mdm|msm|qcm|qcs|q[dr]u|sa|sar|sc|sd[amx]|sm|x1[ep])[0-9]+.*$"
+        - pattern: "^qcom,.*(glymur|milos).*$"
  required:
    - compatible

@@ -34,6 +36,7 @@ properties:
      - pattern: "^qcom,(apq|ipq|mdm|msm|qcm|qcs|q[dr]u|sa|sc|sd[amx]|sm|x1[ep])[0-9]+(pro)?-.*$"
      - pattern: "^qcom,sar[0-9]+[a-z]?-.*$"
      - pattern: "^qcom,(sa|sc)8[0-9]+[a-z][a-z]?-.*$"
+      - pattern: "^qcom,(glymur|milos)-.*$"

      # Legacy namings - variations of existing patterns/compatibles are OK,
      # but do not add completely new entries to these:
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -10,100 +10,6 @@ maintainers:
  - Bjorn Andersson <bjorn.andersson@linaro.org>

 description: |
-  For devices using the Qualcomm SoC the "compatible" properties consists of
-  one or several "manufacturer,model" strings, describing the device itself,
-  followed by one or several "qcom,<SoC>" strings, describing the SoC used in
-  the device.
-
-  The 'SoC' element must be one of the following strings:
-
-        apq8016
-        apq8026
-        apq8064
-        apq8074
-        apq8084
-        apq8094
-        apq8096
-        ipq4018
-        ipq4019
-        ipq5018
-        ipq5332
-        ipq5424
-        ipq6018
-        ipq8064
-        ipq8074
-        ipq9574
-        mdm9615
-        msm8226
-        msm8660
-        msm8916
-        msm8917
-        msm8926
-        msm8929
-        msm8939
-        msm8953
-        msm8956
-        msm8960
-        msm8974
-        msm8974pro
-        msm8976
-        msm8992
-        msm8994
-        msm8996
-        msm8996pro
-        msm8998
-        qcs404
-        qcs615
-        qcs8300
-        qcs8550
-        qcm2290
-        qcm6490
-        qcs9100
-        qdu1000
-        qrb2210
-        qrb4210
-        qru1000
-        sa8155p
-        sa8540p
-        sa8775p
-        sar2130p
-        sc7180
-        sc7280
-        sc8180x
-        sc8280xp
-        sda660
-        sdm450
-        sdm630
-        sdm632
-        sdm636
-        sdm660
-        sdm670
-        sdm845
-        sdx55
-        sdx65
-        sdx75
-        sm4250
-        sm4450
-        sm6115
-        sm6115p
-        sm6125
-        sm6350
-        sm6375
-        sm7125
-        sm7150
-        sm7225
-        sm7325
-        sm8150
-        sm8250
-        sm8350
-        sm8450
-        sm8550
-        sm8650
-        sm8750
-        x1e78100
-        x1e80100
-        x1p42100
-
  There are many devices in the list below that run the standard ChromeOS
  bootloader setup and use the open source depthcharge bootloader to boot the
  OS. These devices use the bootflow explained at
@@ -203,6 +109,12 @@ properties:
              - samsung,expressatt
          - const: qcom,msm8960

+      - items:
+          - enum:
+              - sony,huashan
+          - const: qcom,msm8960t
+          - const: qcom,msm8960
+
      - items:
          - enum:
              - lge,hammerhead
@@ -281,6 +193,7 @@ properties:

      - items:
          - enum:
+              - flipkart,rimob
              - motorola,potter
              - xiaomi,daisy
              - xiaomi,mido
@@ -424,6 +337,7 @@ properties:
      - items:
          - enum:
              - fairphone,fp5
+              - particle,tachyon
              - qcom,qcm6490-idp
              - qcom,qcs6490-rb3gen2
              - shift,otter
@@ -942,6 +856,7 @@ properties:

      - items:
          - enum:
+              - qcom,monaco-evk
              - qcom,qcs8300-ride
          - const: qcom,qcs8300

@@ -949,6 +864,7 @@ properties:
          - enum:
              - qcom,qcs615-ride
          - const: qcom,qcs615
+          - const: qcom,sm6150

      - items:
          - enum:
@@ -969,6 +885,7 @@ properties:

      - items:
          - enum:
+              - qcom,lemans-evk
              - qcom,qcs9100-ride
              - qcom,qcs9100-ride-r3
          - const: qcom,qcs9100
@@ -976,9 +893,6 @@ properties:

      - items:
          - enum:
-              - google,cheza
-              - google,cheza-rev1
-              - google,cheza-rev2
              - lenovo,yoga-c630
              - lg,judyln
              - lg,judyp
@@ -1076,6 +990,8 @@ properties:
              - qcom,qrb5165-rb5
              - qcom,sm8250-hdk
              - qcom,sm8250-mtp
+              - samsung,r8q
+              - samsung,x1q
              - sony,pdx203-generic
              - sony,pdx206-generic
              - xiaomi,elish
@@ -1095,6 +1011,7 @@ properties:
          - enum:
              - qcom,sm8450-hdk
              - qcom,sm8450-qrd
+              - samsung,r0q
              - sony,pdx223
              - sony,pdx224
          - const: qcom,sm8450
@@ -1146,6 +1063,8 @@ properties:
          - enum:
              - asus,vivobook-s15
              - asus,zenbook-a14-ux3407ra
+              - dell,inspiron-14-plus-7441
+              - dell,latitude-7455
              - dell,xps13-9345
              - hp,elitebook-ultra-g1q
              - hp,omnibook-x14
@@ -1156,9 +1075,17 @@ properties:
              - qcom,x1e80100-qcp
          - const: qcom,x1e80100

+      - items:
+          - enum:
+              - qcom,hamoa-iot-evk
+          - const: qcom,hamoa-iot-som
+          - const: qcom,x1e80100
+
      - items:
          - enum:
              - asus,zenbook-a14-ux3407qa
+              - hp,omnibook-x14-fe1
+              - lenovo,thinkbook-16
              - qcom,x1p42100-crd
          - const: qcom,x1p42100

--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -54,6 +54,11 @@ properties:
          - const: ariaboard,photonicat
          - const: rockchip,rk3568

+      - description: ArmSoM Sige1 board
+        items:
+          - const: armsom,sige1
+          - const: rockchip,rk3528
+
      - description: ArmSoM Sige5 board
        items:
          - const: armsom,sige5
@@ -253,6 +258,11 @@ properties:
          - const: firefly,roc-rk3576-pc
          - const: rockchip,rk3576

+      - description: Firefly ROC-RK3588-RT
+        items:
+          - const: firefly,roc-rk3588-rt
+          - const: rockchip,rk3588
+
      - description: Firefly Station M2
        items:
          - const: firefly,rk3566-roc-pc
@@ -320,6 +330,11 @@ properties:
              - friendlyarm,nanopi-r6s
          - const: rockchip,rk3588s

+      - description: FriendlyElec NanoPi Zero2
+        items:
+          - const: friendlyarm,nanopi-zero2
+          - const: rockchip,rk3528
+
      - description: FriendlyElec NanoPC T6 series boards
        items:
          - enum:
@@ -683,6 +698,13 @@ properties:
          - const: hardkernel,odroid-m2
          - const: rockchip,rk3588s

+      - description: HINLINK H66K / H68K
+        items:
+          - enum:
+              - hinlink,h66k
+              - hinlink,h68k
+          - const: rockchip,rk3568
+
      - description: Hugsun X99 TV Box
        items:
          - const: hugsun,x99
@@ -881,6 +903,13 @@ properties:
          - const: radxa,rock
          - const: rockchip,rk3188

+      - description: Radxa ROCK 2A/2F
+        items:
+          - enum:
+              - radxa,rock-2a
+              - radxa,rock-2f
+          - const: rockchip,rk3528
+
      - description: Radxa ROCK Pi 4A/A+/B/B+/C
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
+++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
@@ -14,12 +14,6 @@ properties:
    const: '/'
  compatible:
    oneOf:
-      - description: S3C2416 based boards
-        items:
-          - enum:
-              - samsung,smdk2416                # Samsung SMDK2416
-          - const: samsung,s3c2416
-
      - description: S3C6410 based boards
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/sti.yaml
+++ b/Documentation/devicetree/bindings/arm/sti.yaml
@@ -14,12 +14,8 @@ properties:
    const: '/'
  compatible:
    oneOf:
-      - items:
-          - const: st,stih407-b2120
-          - const: st,stih407
      - items:
          - enum:
-              - st,stih410-b2120
              - st,stih410-b2260
          - const: st,stih410
      - items:
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -595,6 +595,14 @@ properties:
          - const: netcube,kumquat
          - const: allwinner,sun8i-v3s

+      - description: NetCube Systems Nagami SoM based boards
+        items:
+          - enum:
+              - netcube,nagami-basic-carrier
+              - netcube,nagami-keypad-carrier
+          - const: netcube,nagami
+          - const: allwinner,sun8i-t113s
+
      - description: NextThing Co. CHIP
        items:
          - const: nextthing,chip
@@ -963,6 +971,11 @@ properties:
          - const: hechuang,x96-mate
          - const: allwinner,sun50i-h616

+      - description: X96Q
+        items:
+          - const: amediatech,x96q
+          - const: allwinner,sun50i-h616
+
      - description: X96Q Pro+
        items:
          - const: amediatech,x96q-pro-plus
--- a/Documentation/devicetree/bindings/arm/tegra.yaml
+++ b/Documentation/devicetree/bindings/arm/tegra.yaml
@@ -36,8 +36,12 @@ properties:
              - toradex,colibri_t20-iris
          - const: toradex,colibri_t20
          - const: nvidia,tegra20
-      - items:
-          - const: asus,tf101
+      - description: ASUS Transformers T20 Device family
+        items:
+          - enum:
+              - asus,sl101
+              - asus,tf101
+              - asus,tf101g
          - const: nvidia,tegra20
      - items:
          - const: acer,picasso
@@ -174,6 +178,10 @@ properties:
          - const: google,nyan-big
          - const: google,nyan
          - const: nvidia,tegra124
+      - description: Xiaomi Mi Pad (A0101)
+        items:
+          - const: xiaomi,mocha
+          - const: nvidia,tegra124
      - items:
          - enum:
              - nvidia,darcy
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -58,6 +58,13 @@ properties:
              - ti,am62-lp-sk
          - const: ti,am625

+      - description: K3 AM6254atl SiP
+        items:
+          - enum:
+              - ti,am6254atl-sk
+          - const: ti,am6254atl
+          - const: ti,am625
+
      - description: K3 AM62x SoC Toradex Verdin Modules and Carrier Boards
        items:
          - enum:
@@ -106,6 +113,12 @@ properties:
          - const: toradex,verdin-am62p          # Verdin AM62P Module
          - const: ti,am62p5

+      - description: K3 AM62P5 SoC Variscite SOM and Carrier Boards
+        items:
+          - const: variscite,var-som-am62p-symphony
+          - const: variscite,var-som-am62p
+          - const: ti,am62p5
+
      - description: K3 AM642 SoC
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/ti/ti,keystone.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/ti,keystone.yaml
@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/ti/ti,keystone.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI Keystone Platforms
+
+maintainers:
+  - Nishanth Menon <nm@ti.com>
+  - Santosh Shilimkar <ssantosh@kernel.org>
+
+properties:
+  compatible:
+    oneOf:
+      - description: K2G
+        items:
+          - enum:
+              - ti,k2g-evm
+              - ti,k2g-ice
+          - const: ti,k2g
+          - const: ti,keystone
+      - description: Keystone 2 Edison
+        items:
+          - enum:
+              - ti,k2e-evm
+          - const: ti,k2e
+          - const: ti,keystone
+      - description: Keystone 2 Lamarr
+        items:
+          - enum:
+              - ti,k2l-evm
+          - const: ti,k2l
+          - const: ti,keystone
+      - description: Keystone 2 Hawking/Kepler
+        items:
+          - enum:
+              - ti,k2hk-evm
+          - const: ti,k2hk
+          - const: ti,keystone
+
+additionalProperties: true
--- a/Documentation/devicetree/bindings/clock/allwinner,sun55i-a523-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun55i-a523-ccu.yaml
@@ -19,6 +19,7 @@ properties:
  compatible:
    enum:
      - allwinner,sun55i-a523-ccu
+      - allwinner,sun55i-a523-mcu-ccu
      - allwinner,sun55i-a523-r-ccu

  reg:
@@ -26,11 +27,11 @@ properties:

  clocks:
    minItems: 4
-    maxItems: 5
+    maxItems: 9

  clock-names:
    minItems: 4
-    maxItems: 5
+    maxItems: 9

 required:
  - "#clock-cells"
@@ -63,6 +64,38 @@ allOf:
            - const: iosc
            - const: losc-fanout

+  - if:
+      properties:
+        compatible:
+          enum:
+            - allwinner,sun55i-a523-mcu-ccu
+
+    then:
+      properties:
+        clocks:
+          items:
+            - description: High Frequency Oscillator (usually at 24MHz)
+            - description: Low Frequency Oscillator (usually at 32kHz)
+            - description: Internal Oscillator
+            - description: Audio PLL (4x)
+            - description: Peripherals PLL 0 (300 MHz output)
+            - description: DSP module clock
+            - description: MBUS clock
+            - description: PRCM AHB clock
+            - description: PRCM APB0 clock
+
+        clock-names:
+          items:
+            - const: hosc
+            - const: losc
+            - const: iosc
+            - const: pll-audio0-4x
+            - const: pll-periph0-300m
+            - const: dsp
+            - const: mbus
+            - const: r-ahb
+            - const: r-apb0
+
  - if:
      properties:
        compatible:
--- a/Documentation/devicetree/bindings/clock/qcom,ipq5424-apss-clk.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,ipq5424-apss-clk.yaml
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/qcom,ipq5424-apss-clk.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm APSS IPQ5424 Clock Controller
+
+maintainers:
+  - Varadarajan Narayanan <quic_varada@quicinc.com>
+
+description:
+  The CPU core in ipq5424 is clocked by a huayra PLL with RCG support.
+  The RCG and PLL have a separate register space from the GCC.
+
+properties:
+  compatible:
+    enum:
+      - qcom,ipq5424-apss-clk
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Reference to the XO clock.
+      - description: Reference to the GPLL0 clock.
+
+  '#clock-cells':
+    const: 1
+
+  '#interconnect-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - '#clock-cells'
+  - '#interconnect-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,ipq5424-gcc.h>
+
+    apss_clk: clock-controller@fa80000 {
+      compatible = "qcom,ipq5424-apss-clk";
+      reg = <0x0fa80000 0x20000>;
+      clocks = <&xo_board>,
+               <&gcc GPLL0>;
+      #clock-cells = <1>;
+      #interconnect-cells = <1>;
+    };
--- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-vi.yaml
+++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-vi.yaml
@@ -70,9 +70,6 @@ properties:
  ranges:
    maxItems: 1

-  avdd-dsi-csi-supply:
-    description: DSI/CSI power supply. Must supply 1.2 V.
-
  vip:
    $ref: /schemas/display/tegra/nvidia,tegra20-vip.yaml

--- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra210-csi.yaml
+++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra210-csi.yaml
@@ -37,6 +37,9 @@ properties:
      - const: cile
      - const: csi_tpg

+  avdd-dsi-csi-supply:
+    description: DSI/CSI power supply. Must supply 1.2 V.
+
  power-domains:
    maxItems: 1

--- a/Documentation/devicetree/bindings/firmware/nxp,imx95-scmi.yaml
+++ b/Documentation/devicetree/bindings/firmware/nxp,imx95-scmi.yaml
@@ -24,13 +24,19 @@ properties:
        const: 0x80

  protocol@81:
-    $ref: '/schemas/firmware/arm,scmi.yaml#/$defs/protocol-node'
-    unevaluatedProperties: false
+    type: object
+    allOf:
+      - $ref: '/schemas/firmware/arm,scmi.yaml#/$defs/protocol-node'
+      - $ref: /schemas/input/input.yaml#
+    additionalProperties: false

    properties:
      reg:
        const: 0x81

+      linux,code:
+        default: 116  # KEY_POWER
+
  protocol@82:
    description:
      SCMI CPU Protocol which allows an agent to start or stop a CPU. It is
--- a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.yaml
@@ -85,6 +85,12 @@ properties:
          the previous generations, but have a different parent clock and hence
          the timing parameters are configured differently.
        const: nvidia,tegra256-i2c
+      - description:
+          Tegra264 has 17 generic I2C controllers, two of which are in the AON
+          (always-on) partition of the SoC. In addition to the features from
+          Tegra194, a SW mutex register is added to support use of the same I2C
+          instance across multiple firmwares.
+        const: nvidia,tegra264-i2c

  reg:
    maxItems: 1
@@ -192,6 +198,7 @@ allOf:
              enum:
                - nvidia,tegra194-i2c
                - nvidia,tegra256-i2c
+                - nvidia,tegra264-i2c
    then:
      required:
        - resets
--- a/Documentation/devicetree/bindings/memory-controllers/starfive,jh7110-dmc.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/starfive,jh7110-dmc.yaml
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/starfive,jh7110-dmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 DMC
+
+maintainers:
+  - E Shattow <e@freeshell.de>
+
+description:
+  JH7110 DDR external memory interface LPDDR4/DDR4/DDR3/LPDDR3 32-bit at
+  2133Mbps (up to 2800Mbps).
+
+properties:
+  compatible:
+    items:
+      - const: starfive,jh7110-dmc
+
+  reg:
+    items:
+      - description: controller registers
+      - description: phy registers
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: pll
+
+  resets:
+    items:
+      - description: axi
+      - description: osc
+      - description: apb
+
+  reset-names:
+    items:
+      - const: axi
+      - const: osc
+      - const: apb
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+    #include <dt-bindings/reset/starfive,jh7110-crg.h>
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      memory-controller@15700000 {
+        compatible = "starfive,jh7110-dmc";
+        reg = <0x0 0x15700000 0x0 0x10000>,
+              <0x0 0x13000000 0x0 0x10000>;
+        clocks = <&syscrg JH7110_PLLCLK_PLL1_OUT>;
+        clock-names = "pll";
+        resets = <&syscrg JH7110_SYSRST_DDR_AXI>,
+                 <&syscrg JH7110_SYSRST_DDR_OSC>,
+                 <&syscrg JH7110_SYSRST_DDR_APB>;
+        reset-names = "axi", "osc", "apb";
+      };
+    };
--- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml
+++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml
@@ -61,7 +61,7 @@ properties:
    description: Specifies that controller should use auto CMD12

 allOf:
-  - $ref: mmc-controller.yaml#
+  - $ref: sdhci-common.yaml#
  - if:
      properties:
        clock-names:
--- a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
+++ b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
@@ -50,6 +50,9 @@ properties:
      - const: hclk
      - const: cclk

+  resets:
+    maxItems: 1
+
  bosch,mram-cfg:
    description: |
      Message RAM configuration data.
--- a/Documentation/devicetree/bindings/riscv/extensions.yaml
+++ b/Documentation/devicetree/bindings/riscv/extensions.yaml
@@ -669,6 +669,24 @@ properties:
            https://mips.com/wp-content/uploads/2025/06/P8700_Programmers_Reference_Manual_Rev1.84_5-31-2025.pdf

        # SiFive
+        - const: xsfcease
+          description:
+            SiFive CEASE Instruction Extensions Specification.
+            See more details in
+            https://www.sifive.com/document-file/freedom-u740-c000-manual
+
+        - const: xsfcflushdlone
+          description:
+            SiFive L1D Cache Flush Instruction Extensions Specification.
+            See more details in
+            https://www.sifive.com/document-file/freedom-u740-c000-manual
+
+        - const: xsfpgflushdlone
+          description:
+            SiFive PGFLUSH Instruction Extensions for the power management. The
+            CPU will flush the L1D and enter the cease state after executing
+            the instruction.
+
        - const: xsfvqmaccdod
          description:
            SiFive Int8 Matrix Multiplication Extensions Specification.
--- a/Documentation/devicetree/bindings/riscv/microchip.yaml
+++ b/Documentation/devicetree/bindings/riscv/microchip.yaml
@@ -18,13 +18,26 @@ properties:
    const: '/'
  compatible:
    oneOf:
+      - items:
+          - const: microchip,mpfs-icicle-prod-reference-rtl-v2507
+          - const: microchip,mpfs-icicle-kit-prod
+          - const: microchip,mpfs-icicle-kit
+          - const: microchip,mpfs-prod
+          - const: microchip,mpfs
+
      - items:
          - enum:
              - microchip,mpfs-icicle-reference-rtlv2203
              - microchip,mpfs-icicle-reference-rtlv2210
+              - microchip,mpfs-icicle-es-reference-rtl-v2507
          - const: microchip,mpfs-icicle-kit
          - const: microchip,mpfs

+      - items:
+          - const: microchip,mpfs-disco-kit-reference-rtl-v2507
+          - const: microchip,mpfs-disco-kit
+          - const: microchip,mpfs
+
      - items:
          - enum:
              - aldec,tysom-m-mpfs250t-rev2
--- a/Documentation/devicetree/bindings/riscv/spacemit.yaml
+++ b/Documentation/devicetree/bindings/riscv/spacemit.yaml
@@ -22,6 +22,7 @@ properties:
          - enum:
              - bananapi,bpi-f3
              - milkv,jupiter
+              - xunlong,orangepi-rv2
          - const: spacemit,k1

 additionalProperties: true
--- a/Documentation/devicetree/bindings/riscv/starfive.yaml
+++ b/Documentation/devicetree/bindings/riscv/starfive.yaml
@@ -28,6 +28,8 @@ properties:
          - enum:
              - deepcomputing,fml13v01
              - milkv,mars
+              - milkv,marscm-emmc
+              - milkv,marscm-lite
              - pine64,star64
              - starfive,visionfive-2-v1.2a
              - starfive,visionfive-2-v1.3b
--- a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
+++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
@@ -38,6 +38,7 @@ properties:
          - const: simple-mfd
      - items:
          - enum:
+              - fsl,imx53-iomuxc-gpr
              - fsl,imx8mm-iomuxc-gpr
              - fsl,imx8mn-iomuxc-gpr
              - fsl,imx8mp-iomuxc-gpr
--- a/Documentation/devicetree/bindings/soc/renesas/renesas.yaml
+++ b/Documentation/devicetree/bindings/soc/renesas/renesas.yaml
@@ -473,6 +473,12 @@ properties:
          - const: renesas,r8a779mb
          - const: renesas,r8a7795

+      - description: R-Car X5H (R8A78000)
+        items:
+          - enum:
+              - renesas,ironhide    # Ironhide (RTP8A78000ASKB0F10S)
+          - const: renesas,r8a78000
+
      - description: RZ/N1D (R9A06G032)
        items:
          - enum:
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@@ -31,6 +31,7 @@ properties:
              - rockchip,rk3568-usb2phy-grf
              - rockchip,rk3576-bigcore-grf
              - rockchip,rk3576-cci-grf
+              - rockchip,rk3576-dcphy-grf
              - rockchip,rk3576-gpu-grf
              - rockchip,rk3576-hdptxphy-grf
              - rockchip,rk3576-litcore-grf
@@ -47,6 +48,7 @@ properties:
              - rockchip,rk3576-vop-grf
              - rockchip,rk3588-bigcore0-grf
              - rockchip,rk3588-bigcore1-grf
+              - rockchip,rk3588-csidphy-grf
              - rockchip,rk3588-dcphy-grf
              - rockchip,rk3588-hdptxphy-grf
              - rockchip,rk3588-ioc
@@ -300,6 +302,7 @@ allOf:
        compatible:
          contains:
            enum:
+              - rockchip,rk3576-dcphy-grf
              - rockchip,rk3576-vo1-grf
              - rockchip,rk3588-vo-grf
              - rockchip,rk3588-vo0-grf
--- a/Documentation/devicetree/bindings/soc/xilinx/xilinx.yaml
+++ b/Documentation/devicetree/bindings/soc/xilinx/xilinx.yaml
@@ -116,6 +116,36 @@ properties:
          - const: xlnx,zynqmp-zcu111
          - const: xlnx,zynqmp

+      - description: Xilinx Kria SOMs K24
+        minItems: 3
+        items:
+          enum:
+            - xlnx,zynqmp-sm-k24-rev1
+            - xlnx,zynqmp-sm-k24-revB
+            - xlnx,zynqmp-sm-k24-revA
+            - xlnx,zynqmp-sm-k24
+            - xlnx,zynqmp
+        allOf:
+          - contains:
+              const: xlnx,zynqmp
+          - contains:
+              const: xlnx,zynqmp-sm-k24
+
+      - description: Xilinx Kria SOMs K24 (starter)
+        minItems: 3
+        items:
+          enum:
+            - xlnx,zynqmp-smk-k24-rev1
+            - xlnx,zynqmp-smk-k24-revB
+            - xlnx,zynqmp-smk-k24-revA
+            - xlnx,zynqmp-smk-k24
+            - xlnx,zynqmp
+        allOf:
+          - contains:
+              const: xlnx,zynqmp
+          - contains:
+              const: xlnx,zynqmp-smk-k24
+
      - description: Xilinx Kria SOMs
        minItems: 3
        items:
@@ -148,6 +178,57 @@ properties:
          - contains:
              const: xlnx,zynqmp-smk-k26

+      - description: Xilinx Kria SOM KD240 revA/B/1
+        minItems: 3
+        items:
+          enum:
+            - xlnx,zynqmp-sk-kd240-rev1
+            - xlnx,zynqmp-sk-kd240-revB
+            - xlnx,zynqmp-sk-kd240-revA
+            - xlnx,zynqmp-sk-kd240
+            - xlnx,zynqmp
+        allOf:
+          - contains:
+              const: xlnx,zynqmp-sk-kd240-revA
+          - contains:
+              const: xlnx,zynqmp-sk-kd240
+          - contains:
+              const: xlnx,zynqmp
+
+      - description: Xilinx Kria SOM KR260 revA/Y/Z
+        minItems: 3
+        items:
+          enum:
+            - xlnx,zynqmp-sk-kr260-revA
+            - xlnx,zynqmp-sk-kr260-revY
+            - xlnx,zynqmp-sk-kr260-revZ
+            - xlnx,zynqmp-sk-kr260
+            - xlnx,zynqmp
+        allOf:
+          - contains:
+              const: xlnx,zynqmp-sk-kr260-revA
+          - contains:
+              const: xlnx,zynqmp-sk-kr260
+          - contains:
+              const: xlnx,zynqmp
+
+      - description: Xilinx Kria SOM KR260 rev2/1/B
+        minItems: 3
+        items:
+          enum:
+            - xlnx,zynqmp-sk-kr260-rev2
+            - xlnx,zynqmp-sk-kr260-rev1
+            - xlnx,zynqmp-sk-kr260-revB
+            - xlnx,zynqmp-sk-kr260
+            - xlnx,zynqmp
+        allOf:
+          - contains:
+              const: xlnx,zynqmp-sk-kr260-revB
+          - contains:
+              const: xlnx,zynqmp-sk-kr260
+          - contains:
+              const: xlnx,zynqmp
+
      - description: Xilinx Kria SOM KV260 revA/Y/Z
        minItems: 3
        items:
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -48,6 +48,8 @@ patternProperties:
    description: Acme Systems srl
  "^actions,.*":
    description: Actions Semiconductor Co., Ltd.
+  "^actiontec,.*":
+    description: Actiontec Electronics, Inc
  "^active-semi,.*":
    description: Active-Semi International Inc
  "^ad,.*":
@@ -566,6 +568,8 @@ patternProperties:
    description: Foxconn Industrial Internet
  "^firefly,.*":
    description: Firefly
+  "^flipkart,.*":
+    description: Flipkart Inc.
  "^focaltech,.*":
    description: FocalTech Systems Co.,Ltd
  "^forlinx,.*":
@@ -670,6 +674,8 @@ patternProperties:
    description: HiDeep Inc.
  "^himax,.*":
    description: Himax Technologies, Inc.
+  "^hinlink,.*":
+    description: Shenzhen HINLINK Technology Co., Ltd.
  "^hirschmann,.*":
    description: Hirschmann Automation and Control GmbH
  "^hisi,.*":
@@ -1209,6 +1215,8 @@ patternProperties:
    description: Parade Technologies Inc.
  "^parallax,.*":
    description: Parallax Inc.
+  "^particle,.*":
+    description: Particle Industries, Inc.
  "^pda,.*":
    description: Precision Design Associates, Inc.
  "^pegatron,.*":
--- a/Documentation/process/maintainer-soc.rst
+++ b/Documentation/process/maintainer-soc.rst
@@ -10,7 +10,7 @@ Overview
 The SoC subsystem is a place of aggregation for SoC-specific code.
 The main components of the subsystem are:

-* devicetrees for 32- & 64-bit ARM and RISC-V
+* devicetrees (DTS) for 32- & 64-bit ARM and RISC-V
 * 32-bit ARM board files (arch/arm/mach*)
 * 32- & 64-bit ARM defconfigs
 * SoC-specific drivers across architectures, in particular for 32- & 64-bit
@@ -97,8 +97,8 @@ Perhaps one of the most important things to highlight is that dt-bindings
 document the ABI between the devicetree and the kernel.
 Please read Documentation/devicetree/bindings/ABI.rst.

-If changes are being made to a devicetree that are incompatible with old
-kernels, the devicetree patch should not be applied until the driver is, or an
+If changes are being made to a DTS that are incompatible with old
+kernels, the DTS patch should not be applied until the driver is, or an
 appropriate time later.  Most importantly, any incompatible changes should be
 clearly pointed out in the patch description and pull request, along with the
 expected impact on existing users, such as bootloaders or other operating
--- a/15
+++ b/15
@@ -3120,7 +3120,6 @@ ARM/QUALCOMM CHROMEBOOK SUPPORT
 R:	cros-qcom-dts-watchers@chromium.org
 F:	arch/arm64/boot/dts/qcom/sc7180*
 F:	arch/arm64/boot/dts/qcom/sc7280*
-F:	arch/arm64/boot/dts/qcom/sdm845-cheza*

 ARM/QUALCOMM MAILING LIST
 L:	linux-arm-msm@vger.kernel.org
@@ -4118,6 +4117,18 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/sound/axentia,*
 F:	sound/soc/atmel/tse850-pcm5142.c

+AXIS ARTPEC ARM64 SoC SUPPORT
+M:	Jesper Nilsson <jesper.nilsson@axis.com>
+M:	Lars Persson <lars.persson@axis.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-samsung-soc@vger.kernel.org
+L:	linux-arm-kernel@axis.com
+S:	Maintained
+F:	Documentation/devicetree/bindings/clock/axis,artpec*-clock.yaml
+F:	arch/arm64/boot/dts/exynos/axis/
+F:	drivers/clk/samsung/clk-artpec*.c
+F:	include/dt-bindings/clock/axis,artpec*-clk.h
+
 AXI-FAN-CONTROL HARDWARE MONITOR DRIVER
 M:	Nuno Sá <nuno.sa@analog.com>
 L:	linux-hwmon@vger.kernel.org
@@ -21902,6 +21913,7 @@ M:	Guo Ren <guoren@kernel.org>
 M:	Fu Wei <wefu@redhat.com>
 L:	linux-riscv@lists.infradead.org
 S:	Maintained
+Q:	https://patchwork.kernel.org/project/riscv-thead/list/
 T:	git https://github.com/pdp7/linux.git
 F:	Documentation/devicetree/bindings/clock/thead,th1520-clk-ap.yaml
 F:	Documentation/devicetree/bindings/firmware/thead,th1520-aon.yaml
@@ -26018,6 +26030,7 @@ M:	Goran Rađenović <goran.radni@gmail.com>
 M:	Börge Strümpfel <boerge.struempfel@gmail.com>
 S:	Maintained
 F:	arch/arm/boot/dts/st/stm32mp157c-ultra-fly-sbc.dts
+F:	arch/arm64/boot/dts/freescale/imx8mp-ultra-mach-sbc.dts

 UNICODE SUBSYSTEM
 M:	Gabriel Krisman Bertazi <krisman@kernel.org>
--- a/arch/arm/boot/dts/allwinner/Makefile
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -182,6 +182,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-wits-pro-a20-dkt.dtb

 # Enables support for device-tree overlays for all pis
+DTC_FLAGS_sun8i-h2-plus-orangepi-zero := -@
 DTC_FLAGS_sun8i-h3-orangepi-lite := -@
 DTC_FLAGS_sun8i-h3-bananapi-m2-plus := -@
 DTC_FLAGS_sun8i-h3-nanopi-m1-plus := -@
@@ -199,6 +200,7 @@ DTC_FLAGS_sun8i-h3-nanopi-r1 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc := -@
 DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@
+DTC_FLAGS_sun8i-t113s-netcube-nagami-basic-carrier := -@
 DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-evb.dtb \
@@ -225,6 +227,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h2-plus-libretech-all-h3-cc.dtb \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
+	sun8i-h2-plus-orangepi-zero-interface-board.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
 	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
 	sun8i-h3-beelink-x2.dtb \
@@ -244,6 +247,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-orangepi-plus.dtb \
 	sun8i-h3-orangepi-plus2e.dtb \
 	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-orangepi-zero-plus2-interface-board.dtb \
 	sun8i-h3-rervision-dvk.dtb \
 	sun8i-h3-zeropi.dtb \
 	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
@@ -257,6 +261,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-s3-lichee-zero-plus.dtb \
 	sun8i-s3-pinecube.dtb \
 	sun8i-t113s-mangopi-mq-r-t113.dtb \
+	sun8i-t113s-netcube-nagami-basic-carrier.dtb \
+	sun8i-t113s-netcube-nagami-keypad-carrier.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v3-sl631-imx179.dtb \
 	sun8i-v3s-anbernic-rg-nano.dtb \
@@ -264,6 +270,10 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-v3s-licheepi-zero-dock.dtb \
 	sun8i-v3s-netcube-kumquat.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
+sun8i-h2-plus-orangepi-zero-interface-board-dtbs += \
+	sun8i-h2-plus-orangepi-zero.dtb sun8i-orangepi-zero-interface-board.dtbo
+sun8i-h3-orangepi-zero-plus2-interface-board-dtbs += \
+	sun8i-h3-orangepi-zero-plus2.dtb sun8i-orangepi-zero-interface-board.dtbo
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
@@ -112,6 +112,20 @@ wifi_pwrseq: pwrseq {
 	};
 };

+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - https://linux-sunxi.org/Xunlong_Orange_Pi_Zero#Expansion_Port
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_vdd_cpux>;
 };
--- a/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
@@ -99,6 +99,20 @@ wifi_pwrseq: pwrseq {
 	};
 };

+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-Plus-2.html
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &de {
 	status = "okay";
 };
--- a/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
+++ b/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright (C) 2025 J. Neuschäfer <j.ne@posteo.net>
+ *
+ * Devicetree overlay for the Orange Pi Zero Interface board (OP0014).
+ *
+ *   https://orangepi.com/index.php?route=product/product&product_id=871
+ *
+ * This overlay applies to the following base files:
+ *
+ * - arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+ * - arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+&codec {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_ir_rx_pin>;
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+/ {
+	model = "NetCube Systems Nagami Basic Carrier Board";
+	compatible = "netcube,nagami-basic-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+};
+
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2s1 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	broken-cd;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	status = "okay";
+};
--- a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "NetCube Systems Nagami Keypad Carrier Board";
+	compatible = "netcube,nagami-keypad-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: led-status-red {
+			gpios = <&pio 3 16 GPIO_ACTIVE_HIGH>;  /* PD16 */
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
+		};
+
+		led_status_green: led-status-green {
+			gpios = <&pio 3 22 GPIO_ACTIVE_HIGH>;  /* PD22 */
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	tca8418: keypad@34 {
+		compatible = "ti,tca8418";
+		reg = <0x34>;
+		interrupts-extended = <&pio 5 6 IRQ_TYPE_EDGE_FALLING>;  /* PF6 */
+		linux,keymap = <MATRIX_KEY(0x03, 0x00, KEY_NUMERIC_A)
+				MATRIX_KEY(0x03, 0x01, KEY_NUMERIC_1)
+				MATRIX_KEY(0x03, 0x02, KEY_NUMERIC_2)
+				MATRIX_KEY(0x03, 0x03, KEY_NUMERIC_3)
+				MATRIX_KEY(0x02, 0x00, KEY_NUMERIC_B)
+				MATRIX_KEY(0x02, 0x01, KEY_NUMERIC_4)
+				MATRIX_KEY(0x02, 0x02, KEY_NUMERIC_5)
+				MATRIX_KEY(0x02, 0x03, KEY_NUMERIC_6)
+				MATRIX_KEY(0x01, 0x00, KEY_NUMERIC_C)
+				MATRIX_KEY(0x01, 0x01, KEY_NUMERIC_7)
+				MATRIX_KEY(0x01, 0x02, KEY_NUMERIC_8)
+				MATRIX_KEY(0x01, 0x03, KEY_NUMERIC_9)
+				MATRIX_KEY(0x00, 0x00, KEY_NUMERIC_D)
+				MATRIX_KEY(0x00, 0x01, KEY_CLEAR)
+				MATRIX_KEY(0x00, 0x02, KEY_NUMERIC_0)
+				MATRIX_KEY(0x00, 0x03, KEY_OK)
+		>;
+		keypad,num-rows = <4>;
+		keypad,num-columns = <4>;
+	};
+};
+
+&pio {
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PB
+			  "", "", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "", "",
+			  "", "", "", "",
+			  "LED_STATUS_RED", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "LED_STATUS_GREEN", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PF
+			  "", "", "KEY_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "NetCube Systems Nagami SoM";
+	compatible = "netcube,nagami", "allwinner,sun8i-t113s";
+
+	aliases {
+		serial1 = &uart1; // ESP32 Bootloader UART
+		serial3 = &uart3; // Console UART on Card Edge
+		ethernet0 = &emac;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	/* module wide 3.3V supply directly from the card edge */
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	/* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+	reg_vcc_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <880000>;
+		regulator-max-microvolt = <880000>;
+		vin-supply = <&reg_vcc3v3>;
+	};
+
+	/* USB0 MUX to switch connect to Card-Edge only after BootROM */
+	usb0_sec_mux: mux-controller{
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&pio 3 9 GPIO_ACTIVE_HIGH>; /* PD9 */
+		idle-state = <1>; /* USB connected to Card-Edge by default */
+	};
+
+	/* Reset of ESP32 */
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
+		post-power-on-delay-ms = <1500>;
+		power-off-delay-us = <200>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&emac {
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+	phy-handle = <&lan8720a>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&rmii_pe_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Default I2C Interface on Card-Edge */
+&i2c2 {
+	pinctrl-0 = <&i2c2_pd_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Exposed as the QWIIC connector and used by the internal EEPROM */
+&i2c3 {
+	pinctrl-0 = <&i2c3_pg_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c02";		/* actually it's a 24AA02E48 */
+		reg = <0x50>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_vcc3v3>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth0_macaddress: macaddress@fa {
+			reg = <0xfa 0x06>;
+		};
+	};
+};
+
+/* Default I2S Interface on Card-Edge */
+&i2s1 {
+	pinctrl-0 = <&i2s1_pins>, <&i2s1_din0_pin>, <&i2s1_dout0_pin>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Phy is on SoM. MDI signals pre-magnetics are on the card edge */
+&mdio {
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+/* Default SD Interface on Card-Edge */
+&mmc0 {
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Connected to the on-board ESP32 */
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+};
+
+/* Connected to the on-board eMMC */
+&mmc2 {
+	pinctrl-0 = <&mmc2_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pd-supply = <&reg_vcc3v3>;
+	vcc-pe-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "CAN0_TX", "CAN0_RX", // PB
+			  "CAN1_TX", "CAN1_RX", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "SPI1_CS", "SPI1_CLK",
+			  "SPI1_MOSI", "SPI1_MISO", "SPI1_HOLD", "SPI1_WP",
+			  "PD16", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "PD22", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SD_D1", "SD_D0", "SD_CLK", "SD_CLK", // PF
+			  "SD_D3", "SD_D2", "PF6", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "I2S1_WS", "I2S1_CLK", "I2S1_DIN0", "I2S1_DOUT0",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+/* Remove the unused CK pin from the pinctl as it is unconnected */
+&rmii_pe_pins {
+	pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+	       "PE5", "PE6", "PE8", "PE9";
+};
+
+/* Default SPI Interface on Card-Edge */
+&spi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&spi1_pins>, <&spi1_hold_pin>, <&spi1_wp_pin>;
+	pinctrl-names = "default";
+	cs-gpios = <0>;
+	status = "disabled";
+};
+
+/* Connected to the Bootloader/Console of the ESP32 */
+&uart1 {
+	pinctrl-0 = <&uart1_pg6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Console/Debug UART on Card-Edge */
+&uart3 {
+	pinctrl-0 = <&uart3_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -19,8 +19,11 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-delta-ahe50dc.dtb \
 	aspeed-bmc-facebook-bletchley.dtb \
 	aspeed-bmc-facebook-catalina.dtb \
+	aspeed-bmc-facebook-clemente.dtb \
 	aspeed-bmc-facebook-cmm.dtb \
+	aspeed-bmc-facebook-darwin.dtb \
 	aspeed-bmc-facebook-elbert.dtb \
+	aspeed-bmc-facebook-fuji-data64.dtb \
 	aspeed-bmc-facebook-fuji.dtb \
 	aspeed-bmc-facebook-galaxy100.dtb \
 	aspeed-bmc-facebook-greatlakes.dtb \
@@ -31,6 +34,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-facebook-tiogapass.dtb \
 	aspeed-bmc-facebook-wedge40.dtb \
 	aspeed-bmc-facebook-wedge100.dtb \
+	aspeed-bmc-facebook-wedge400-data64.dtb \
 	aspeed-bmc-facebook-wedge400.dtb \
 	aspeed-bmc-facebook-yamp.dtb \
 	aspeed-bmc-facebook-yosemitev2.dtb \
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjefferson.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjefferson.dts
@@ -243,7 +243,7 @@ temperature-sensor@49 {
 				compatible = "ti,tmp75";
 				reg = <0x49>;
 			};
-			temperature-sensor@4a{
+			temperature-sensor@4a {
 				compatible = "ti,tmp75";
 				reg = <0x4a>;
 			};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-arm-stardragon4800-rep2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-arm-stardragon4800-rep2.dts
@@ -171,7 +171,7 @@ eeprom@50 {
 				reg = <0x50>;
 			};
 			dps650ab@58 {
-				compatible = "dps650ab";
+				compatible = "delta,dps650ab";
 				reg = <0x58>;
 			};
 		};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c246d4i.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c246d4i.dts
@@ -106,11 +106,15 @@ eeprom@57 {
 		compatible = "st,24c128", "atmel,24c128";
 		reg = <0x57>;
 		pagesize = <16>;
-		#address-cells = <1>;
-		#size-cells = <1>;

-		eth0_macaddress: macaddress@3f80 {
-			reg = <0x3f80 6>;
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
 		};
 	};
 };
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c256d4i.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c256d4i.dts
@@ -191,11 +191,15 @@ eeprom@57 {
 		compatible = "st,24c128", "atmel,24c128";
 		reg = <0x57>;
 		pagesize = <16>;
-		#address-cells = <1>;
-		#size-cells = <1>;

-		eth0_macaddress: macaddress@3f80 {
-			reg = <0x3f80 6>;
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
 		};
 	};
 };
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-romed8hm3.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-romed8hm3.dts
@@ -134,11 +134,15 @@ eeprom@50 {
 		compatible = "st,24c128", "atmel,24c128";
 		reg = <0x50>;
 		pagesize = <16>;
-		#address-cells = <1>;
-		#size-cells = <1>;

-		eth0_macaddress: macaddress@3f80 {
-			reg = <0x3f80 6>;
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
 		};
 	};
 };
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-x570d4u.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-x570d4u.dts
@@ -232,15 +232,19 @@ eeprom@57 {
 		compatible = "st,24c128", "atmel,24c128";
 		reg = <0x57>;
 		pagesize = <16>;
-		#address-cells = <1>;
-		#size-cells = <1>;

-		eth0_macaddress: macaddress@3f80 {
-			reg = <0x3f80 6>;
-		};
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;

-		eth1_macaddress: macaddress@3f88 {
-			reg = <0x3f88 6>;
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
+
+			eth1_macaddress: macaddress@3f88 {
+				reg = <0x3f88 6>;
+			};
 		};
 	};
 };
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-catalina.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-catalina.dts
@@ -526,11 +526,11 @@ fan-3 {
 					tach-ch = /bits/ 8 <0x03>;
 				};
 			};
-			fanctl0: fan-controller@21{
+			fanctl0: fan-controller@21 {
 				compatible = "maxim,max31790";
 				reg = <0x21>;
 			};
-			fanctl1: fan-controller@27{
+			fanctl1: fan-controller@27 {
 				compatible = "maxim,max31790";
 				reg = <0x27>;
 			};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-darwin.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-darwin.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+
+/dts-v1/;
+
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Darwin BMC";
+	compatible = "facebook,darwin-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart5;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			      <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	spi_gpio: spi {
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c0 {
+	eeprom@50 {
+		compatible = "atmel,24c512";
+		reg = <0x50>;
+	};
+};
+
+&adc0 {
+	status = "okay";
+
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		     &pinctrl_adc2_default &pinctrl_adc3_default
+		     &pinctrl_adc4_default &pinctrl_adc5_default
+		     &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	status = "okay";
+
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		     &pinctrl_adc10_default &pinctrl_adc11_default
+		     &pinctrl_adc12_default &pinctrl_adc13_default
+		     &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+
+	non-removable;
+	max-frequency = <25000000>;
+	bus-width = <4>;
+};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-elbert.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-elbert.dts
@@ -201,3 +201,15 @@ fixed-link {
 		full-duplex;
 	};
 };
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+
+	non-removable;
+	max-frequency = <25000000>;
+	bus-width = <4>;
+};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-harma.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-harma.dts
@@ -183,11 +183,9 @@ &kcs3 {
 &i2c0 {
 	status = "okay";

-	pwm@5e{
-		compatible = "max31790";
+	pwm@5e {
+		compatible = "maxim,max31790";
 		reg = <0x5e>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 	};

 	power-sensor@40 {
@@ -234,7 +232,7 @@ gpio@12 {
 		"","",
 		"","",
 		"","",
-		"","fcb1-activate",
+		"","fcb2-activate",
 		"","";
 	};
 };
@@ -257,11 +255,9 @@ eeprom@50 {
 &i2c2 {
 	status = "okay";

-	pwm@5e{
-		compatible = "max31790";
+	pwm@5e {
+		compatible = "maxim,max31790";
 		reg = <0x5e>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 	};

 	power-sensor@40 {
@@ -308,7 +304,7 @@ gpio@12 {
 		"","",
 		"","",
 		"","",
-		"","fcb0-activate",
+		"","fcb1-activate",
 		"","";
 	};
 };
@@ -373,6 +369,12 @@ power-monitor@40 {
 		compatible = "infineon,xdp710";
 		reg = <0x40>;
 	};
+
+	power-sensor@45 {
+		compatible = "ti,ina238";
+		reg = <0x45>;
+		shunt-resistor = <500>;
+	};
 };

 &i2c5 {
@@ -514,6 +516,10 @@ imux28: i2c@0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
+			power-sensor@20 {
+				compatible = "mps,mp5990";
+				reg = <0x20>;
+			};
 			power-monitor@61 {
 				compatible = "isil,isl69260";
 				reg = <0x61>;
@@ -692,14 +698,14 @@ &sgpiom0 {
 	"","",
 	/*A4-A7 line 8-15*/
 	"","power-config-asic-module-enable",
-	"","power-config-asic-power-good",
-	"","power-config-pdb-power-good",
+	"power-p3v3-standby","power-config-asic-power-good",
+	"power-p1v8-good","power-config-pdb-power-good",
 	"presence-cpu","smi-control-n",
 	/*B0-B3 line 16-23*/
 	"","nmi-control-n",
-	"","nmi-control-sync-flood-n",
-	"","",
+	"power-pvdd33-s5","nmi-control-sync-flood-n",
 	"","",
+	"power-pvdd18-s5","",
 	/*B4-B7 line 24-31*/
 	"","FM_CPU_SP5R1",
 	"reset-cause-rsmrst","FM_CPU_SP5R2",
@@ -743,7 +749,7 @@ &sgpiom0 {
 	/*F4-F7 line 88-95*/
 	"presence-asic-modules-0","rt-cpu0-p1-force-enable",
 	"presence-asic-modules-1","bios-debug-msg-disable",
-	"","uart-control-buffer-select",
+	"power-asic-good","uart-control-buffer-select",
 	"presence-cmm","ac-control-n",
 	/*G0-G3 line 96-103*/
 	"FM_CPU_CORETYPE2","",
@@ -795,7 +801,7 @@ &sgpiom0 {
 	"asic0-card-type-detection2-n","",
 	"uart-switch-lsb","",
 	"uart-switch-msb","",
-	"","",
+	"power-12v-memory-good","",
 	/*M4-M7 line 200-207*/
 	"","","","","","","","",
 	/*N0-N3 line 208-215*/
@@ -803,7 +809,10 @@ &sgpiom0 {
 	/*N4-N7 line 216-223*/
 	"","","","","","","","",
 	/*O0-O3 line 224-231*/
-	"","","","","","","","",
+	"","",
+	"irq-pvddcore0-ocp-alert","",
+	"irq-pvddcore1-ocp-alert","",
+	"","",
 	/*O4-O7 line 232-239*/
 	"","","","","","","","",
 	/*P0-P3 line 240-247*/
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts
@@ -312,11 +312,9 @@ eeprom@50 {
 				reg = <0x50>;
 			};

-			pwm@5e{
-				compatible = "max31790";
+			pwm@5e {
+				compatible = "maxim,max31790";
 				reg = <0x5e>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};

 			power-sensor@40 {
@@ -435,11 +433,9 @@ eeprom@50 {
 				reg = <0x50>;
 			};

-			pwm@5e{
-				compatible = "max31790";
+			pwm@5e {
+				compatible = "maxim,max31790";
 				reg = <0x5e>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};

 			power-sensor@40 {
@@ -558,11 +554,9 @@ eeprom@50 {
 				reg = <0x50>;
 			};

-			pwm@5e{
-				compatible = "max31790";
+			pwm@5e {
+				compatible = "maxim,max31790";
 				reg = <0x5e>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};

 			power-sensor@40 {
@@ -681,11 +675,9 @@ eeprom@50 {
 				reg = <0x50>;
 			};

-			pwm@5e{
-				compatible = "max31790";
+			pwm@5e {
+				compatible = "maxim,max31790";
 				reg = <0x5e>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};

 			power-sensor@40 {
@@ -804,11 +796,9 @@ eeprom@50 {
 				reg = <0x50>;
 			};

-			pwm@5e{
-				compatible = "max31790";
+			pwm@5e {
+				compatible = "maxim,max31790";
 				reg = <0x5e>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};

 			power-sensor@40 {
@@ -926,11 +916,9 @@ eeprom@50 {
 				reg = <0x50>;
 			};

-			pwm@5e{
-				compatible = "max31790";
+			pwm@5e {
+				compatible = "maxim,max31790";
 				reg = <0x5e>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};

 			power-sensor@40 {
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts
@@ -233,7 +233,7 @@ gpio@20 {
 			"FM_NIC_PPS_IN_S0_R","FM_NIC_PPS_IN_S1_R";
 	};

-	fan-controller@21{
+	fan-controller@21 {
 		compatible = "maxim,max31790";
 		reg = <0x21>;
 	};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-tiogapass.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-tiogapass.dts
@@ -508,7 +508,7 @@ &i2c7 {
 	status = "okay";
 	//HSC, AirMax Conn A
 	adm1278@45 {
-		compatible = "adm1275";
+		compatible = "adi,adm1275";
 		reg = <0x45>;
 		shunt-resistor-micro-ohms = <250>;
 	};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400-data64.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400-data64.dts
@@ -0,0 +1,375 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2019 Facebook Inc.
+/dts-v1/;
+
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include "ast2500-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Wedge 400 BMC (64MB Datastore)";
+	compatible = "facebook,wedge400-data64-bmc", "aspeed,ast2500";
+
+	aliases {
+		/*
+		 * PCA9548 (2-0070) provides 8 channels connecting to
+		 * SCM (System Controller Module).
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * PCA9548 (8-0070) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+
+		/*
+		 * PCA9548 (11-0076) provides 8 channels connecting to
+		 * FCM (Fan Controller Module).
+		 */
+		i2c32 = &imux32;
+		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
+		i2c38 = &imux38;
+		i2c39 = &imux39;
+
+		spi2 = &spi_gpio;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	ast-adc-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			      <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>;
+	};
+
+	/*
+	 * GPIO-based SPI Master is required to access SPI TPM, because
+	 * full-duplex SPI transactions are not supported by ASPEED SPI
+	 * Controllers.
+	 */
+	spi_gpio: spi {
+		status = "okay";
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cs-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_LOW>;
+		sck-gpios = <&gpio ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+};
+
+/*
+ * Both firmware flashes are 128MB on Wedge400 BMC.
+ */
+&fmc_flash0 {
+#include "facebook-bmc-flash-layout-128-data64.dtsi"
+};
+
+&fmc_flash1 {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		flash1@0 {
+			reg = <0x0 0x8000000>;
+			label = "flash1";
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+		     &pinctrl_rxd2_default>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd4_default
+		     &pinctrl_rxd4_default>;
+};
+
+/*
+ * I2C bus #0 is multi-master environment dedicated for BMC and Bridge IC
+ * communication.
+ */
+&i2c0 {
+	status = "okay";
+	multi-master;
+	bus-frequency = <1000000>;
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x76>;
+		i2c-mux-idle-disconnect;
+
+		imux32: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux33: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux34: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux35: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux36: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux37: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux38: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux39: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+	};
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&sdhci1 {
+	max-frequency = <25000000>;
+	/*
+	 * DMA mode needs to be disabled to avoid conflicts with UHCI
+	 * Controller in AST2500 SoC.
+	 */
+	sdhci-caps-mask = <0x0 0x580000>;
+};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400.dts
@@ -1,376 +1,14 @@
 // SPDX-License-Identifier: GPL-2.0+
 // Copyright (c) 2019 Facebook Inc.
-/dts-v1/;

-#include <dt-bindings/gpio/aspeed-gpio.h>
-#include "ast2500-facebook-netbmc-common.dtsi"
+#include "aspeed-bmc-facebook-wedge400-data64.dts"

 / {
 	model = "Facebook Wedge 400 BMC";
 	compatible = "facebook,wedge400-bmc", "aspeed,ast2500";
-
-	aliases {
-		/*
-		 * PCA9548 (2-0070) provides 8 channels connecting to
-		 * SCM (System Controller Module).
-		 */
-		i2c16 = &imux16;
-		i2c17 = &imux17;
-		i2c18 = &imux18;
-		i2c19 = &imux19;
-		i2c20 = &imux20;
-		i2c21 = &imux21;
-		i2c22 = &imux22;
-		i2c23 = &imux23;
-
-		/*
-		 * PCA9548 (8-0070) provides 8 channels connecting to
-		 * SMB (Switch Main Board).
-		 */
-		i2c24 = &imux24;
-		i2c25 = &imux25;
-		i2c26 = &imux26;
-		i2c27 = &imux27;
-		i2c28 = &imux28;
-		i2c29 = &imux29;
-		i2c30 = &imux30;
-		i2c31 = &imux31;
-
-		/*
-		 * PCA9548 (11-0076) provides 8 channels connecting to
-		 * FCM (Fan Controller Module).
-		 */
-		i2c32 = &imux32;
-		i2c33 = &imux33;
-		i2c34 = &imux34;
-		i2c35 = &imux35;
-		i2c36 = &imux36;
-		i2c37 = &imux37;
-		i2c38 = &imux38;
-		i2c39 = &imux39;
-
-		spi2 = &spi_gpio;
-	};
-
-	chosen {
-		stdout-path = &uart1;
-		bootargs = "console=ttyS0,9600n8 root=/dev/ram rw";
-	};
-
-	ast-adc-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
-			      <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>;
-	};
-
-	/*
-	 * GPIO-based SPI Master is required to access SPI TPM, because
-	 * full-duplex SPI transactions are not supported by ASPEED SPI
-	 * Controllers.
-	 */
-	spi_gpio: spi {
-		status = "okay";
-		compatible = "spi-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cs-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_LOW>;
-		gpio-sck = <&gpio ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
-		num-chipselects = <1>;
-
-		tpm@0 {
-			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
-			spi-max-frequency = <33000000>;
-			reg = <0>;
-		};
-	};
 };

-/*
- * Both firmware flashes are 128MB on Wedge400 BMC.
- */
 &fmc_flash0 {
+	/delete-node/partitions;
 #include "facebook-bmc-flash-layout-128.dtsi"
 };
-
-&fmc_flash1 {
-	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		flash1@0 {
-			reg = <0x0 0x8000000>;
-			label = "flash1";
-		};
-	};
-};
-
-&uart2 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd2_default
-		     &pinctrl_rxd2_default>;
-};
-
-&uart4 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd4_default
-		     &pinctrl_rxd4_default>;
-};
-
-/*
- * I2C bus #0 is multi-master environment dedicated for BMC and Bridge IC
- * communication.
- */
-&i2c0 {
-	status = "okay";
-	multi-master;
-	bus-frequency = <1000000>;
-};
-
-&i2c1 {
-	status = "okay";
-};
-
-&i2c2 {
-	status = "okay";
-
-	i2c-mux@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		i2c-mux-idle-disconnect;
-
-		imux16: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux17: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux18: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux19: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux20: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux21: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux22: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux23: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-&i2c3 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-};
-
-&i2c5 {
-	status = "okay";
-};
-
-&i2c6 {
-	status = "okay";
-};
-
-&i2c7 {
-	status = "okay";
-};
-
-&i2c8 {
-	status = "okay";
-
-	i2c-mux@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		i2c-mux-idle-disconnect;
-
-		imux24: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux25: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux26: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux27: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux28: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux29: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux30: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux31: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-
-	};
-};
-
-&i2c9 {
-	status = "okay";
-};
-
-&i2c10 {
-	status = "okay";
-};
-
-&i2c11 {
-	status = "okay";
-
-	i2c-mux@76 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x76>;
-		i2c-mux-idle-disconnect;
-
-		imux32: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux33: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux34: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux35: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux36: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux37: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux38: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux39: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-
-	};
-};
-
-&i2c12 {
-	status = "okay";
-};
-
-&i2c13 {
-	status = "okay";
-};
-
-&adc {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&uhci {
-	status = "okay";
-};
-
-&sdhci1 {
-	max-frequency = <25000000>;
-	/*
-	 * DMA mode needs to be disabled to avoid conflicts with UHCI
-	 * Controller in AST2500 SoC.
-	 */
-	sdhci-caps-mask = <0x0 0x580000>;
-};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1186,19 +1186,19 @@ adc@1f {
 				ti,mode = /bits/ 8 <1>;
 			};

-			pwm@20{
+			pwm@20 {
 				compatible = "maxim,max31790";
 				reg = <0x20>;
 			};

-			gpio@22{
+			gpio@22 {
 				compatible = "ti,tca6424";
 				reg = <0x22>;
 				gpio-controller;
 				#gpio-cells = <2>;
 			};

-			pwm@2f{
+			pwm@2f {
 				compatible = "maxim,max31790";
 				reg = <0x2f>;
 			};
@@ -1234,19 +1234,19 @@ adc@1f {
 				ti,mode = /bits/ 8 <1>;
 			};

-			pwm@20{
+			pwm@20 {
 				compatible = "maxim,max31790";
 				reg = <0x20>;
 			};

-			gpio@22{
+			gpio@22 {
 				compatible = "ti,tca6424";
 				reg = <0x22>;
 				gpio-controller;
 				#gpio-cells = <2>;
 			};

-			pwm@2f{
+			pwm@2f {
 				compatible = "maxim,max31790";
 				reg = <0x2f>;
 			};
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
@@ -2808,6 +2808,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam4_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -2824,6 +2825,7 @@ eeprom@0 {
 			};

 			cfam4_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -2840,8 +2842,8 @@ eeprom@0 {
 			};

 			cfam4_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -2857,8 +2859,8 @@ eeprom@0 {
 			};

 			cfam4_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -3181,6 +3183,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam5_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3197,6 +3200,7 @@ eeprom@0 {
 			};

 			cfam5_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3213,8 +3217,8 @@ eeprom@0 {
 			};

 			cfam5_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -3230,8 +3234,8 @@ eeprom@0 {
 			};

 			cfam5_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -3554,6 +3558,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam6_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3570,6 +3575,7 @@ eeprom@0 {
 			};

 			cfam6_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3586,8 +3592,8 @@ eeprom@0 {
 			};

 			cfam6_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -3603,8 +3609,8 @@ eeprom@0 {
 			};

 			cfam6_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -3927,6 +3933,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam7_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3943,6 +3950,7 @@ eeprom@0 {
 			};

 			cfam7_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3959,8 +3967,8 @@ eeprom@0 {
 			};

 			cfam7_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -3976,8 +3984,8 @@ eeprom@0 {
 			};

 			cfam7_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
@@ -263,7 +263,7 @@ eeprom@51 {
 		reg = <0x51>;
 	};

-	tca_pres1: tca9554@20{
+	tca_pres1: tca9554@20 {
 		compatible = "ti,tca9554";
 		reg = <0x20>;
 		#address-cells = <1>;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts
@@ -3778,10 +3778,10 @@ smb_svc_pex_rssd01_16: pinctrl@20 {
 			pinctrl-0 = <&U65200_pins>;
 			pinctrl-names = "default";
 			U65200_pins: cfg-pins {
-				pins =  "gp60", "gp61", "gp62",
-				"gp63", "gp64", "gp65", "gp66",
-				"gp67", "gp70", "gp71", "gp72",
-				"gp73", "gp74", "gp75", "gp76", "gp77";
+				pins = "gp60", "gp61", "gp62", "gp63", "gp64",
+				       "gp65", "gp66", "gp67", "gp70", "gp71",
+				       "gp72", "gp73", "gp74", "gp75", "gp76",
+				       "gp77";
 				function = "gpio";
 				input-enable;
 				bias-pull-up;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-fp5280g2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-fp5280g2.dts
@@ -54,10 +54,9 @@ video_engine_memory: jpegbuffer {
 	};

 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2500-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;
-		no-gpio-delays;

 		memory-region = <&coldfire_memory>;
 		aspeed,sram = <&sram>;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr855xg2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr855xg2.dts
@@ -151,7 +151,7 @@ &mac1 {
 	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
 };

-&adc{
+&adc {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_adc0_default
@@ -211,7 +211,7 @@ &i2c1 {
 	status = "okay";
 	bus-frequency = <90000>;
 	HotSwap@10 {
-		compatible = "adm1272";
+		compatible = "adi,adm1272";
 		reg = <0x10>;
 	};

--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
@@ -126,6 +126,17 @@ button-uid {
 			gpio = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	standby_power_regulator: standby-power-regulator {
+		status = "okay";
+		compatible = "regulator-fixed";
+		regulator-name = "standby_power";
+		gpio = <&gpio0 ASPEED_GPIO(M, 3) GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		regulator-always-on;
+	};
 };

 // Enable Primary flash on FMC for bring up activity
@@ -216,6 +227,30 @@ &uart_routing {
 	status = "okay";
 };

+&mdio0 {
+	status = "okay";
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+	ethphy3: ethernet-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <2>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy3>;
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
 &mac2 {
 	status = "okay";
 	phy-mode = "rmii";
@@ -247,7 +282,7 @@ &uhci {
 };

 &sgpiom0 {
-	status="okay";
+	status = "okay";
 	ngpios = <128>;
 	gpio-line-names =
 		"","",
@@ -411,7 +446,7 @@ &i2c2 {

 // I2C4
 &i2c3 {
-	status = "disabled";
+	status = "okay";
 };

 // I2C5
@@ -431,6 +466,7 @@ exp4: gpio@21 {
 		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
 		gpio-line-names =
 			"RTC_MUX_SEL-O",
 			"PCI_MUX_SEL-O",
@@ -464,6 +500,7 @@ i2c-mux@71 {
 		#size-cells = <0>;
 		reg = <0x71>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		imux16: i2c@0 {
 			#address-cells = <1>;
@@ -528,6 +565,7 @@ i2c-mux@72 {
 		#size-cells = <0>;
 		reg = <0x72>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		imux20: i2c@0 {
 			#address-cells = <1>;
@@ -545,6 +583,7 @@ gpio@21 {
 				reg = <0x21>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				vcc-supply = <&standby_power_regulator>;
 				gpio-line-names =
 					"RST_CX_0_L-O",
 					"RST_CX_1_L-O",
@@ -584,6 +623,7 @@ i2c-mux@73 {
 		#size-cells = <0>;
 		reg = <0x73>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		imux24: i2c@0 {
 			#address-cells = <1>;
@@ -602,6 +642,7 @@ i2c-mux@70 {
 				#size-cells = <0>;
 				reg = <0x70>;
 				i2c-mux-idle-disconnect;
+				vdd-supply = <&standby_power_regulator>;

 				i2c25mux0: i2c@0 {
 					#address-cells = <1>;
@@ -648,6 +689,7 @@ i2c-mux@75 {
 		#size-cells = <0>;
 		reg = <0x75>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		imux28: i2c@0 {
 			#address-cells = <1>;
@@ -712,6 +754,7 @@ i2c-mux@76 {
 		#size-cells = <0>;
 		reg = <0x76>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		imux32: i2c@0 {
 			#address-cells = <1>;
@@ -729,6 +772,7 @@ gpio@21 {
 				reg = <0x21>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				vcc-supply = <&standby_power_regulator>;
 				gpio-line-names =
 					"SEC_RST_CX_0_L-O",
 					"SEC_RST_CX_1_L-O",
@@ -768,6 +812,7 @@ i2c-mux@77 {
 		#size-cells = <0>;
 		reg = <0x77>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		imux36: i2c@0 {
 			#address-cells = <1>;
@@ -862,6 +907,7 @@ exp0: gpio@20 {
 		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
 		gpio-line-names =
 			"FPGA_THERM_OVERT_L-I",
 			"FPGA_READY_BMC-I",
@@ -891,6 +937,7 @@ exp1: gpio@21 {
 		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
 		gpio-line-names =
 			"SEC_FPGA_THERM_OVERT_L-I",
 			"SEC_FPGA_READY_BMC-I",
@@ -949,6 +996,7 @@ exp3: gpio@74 {
 		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
 		gpio-line-names =
 			"IOB_PRSNT_L",
 			"IOB_DP_HPD",
@@ -1014,6 +1062,7 @@ i2c-mux@77 {
 		#size-cells = <0>;
 		reg = <0x77>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		e1si2c0: i2c@0 {
 			#address-cells = <1>;
@@ -1054,6 +1103,7 @@ i2c-mux@77 {
 		#size-cells = <0>;
 		reg = <0x77>;
 		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;

 		e1si2c4: i2c@0 {
 			#address-cells = <1>;
@@ -1100,7 +1150,7 @@ &gpio0 {
 		/*J0-J7*/ "", "", "", "", "", "", "", "",
 		/*K0-K7*/ "", "", "", "", "", "", "", "",
 		/*L0-L7*/ "", "", "", "", "", "", "", "",
-		/*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "HMC_RESET_L-O", "STBY_POWER_EN-O",
+		/*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "FPGA_RST_L-O", "STBY_POWER_EN-O",
 					"STBY_POWER_PG-I", "PCIE_EP_RST_L-O", "", "",
 		/*N0-N7*/ "", "", "", "", "", "", "", "",
 		/*O0-O7*/ "", "", "", "", "", "", "", "",
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-lanyang.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-lanyang.dts
@@ -63,7 +63,7 @@ sys_err {
 	};

 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;

--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-mowgli.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-mowgli.dts
@@ -165,7 +165,7 @@ fan4 {
 	};

 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;
 		no-gpio-delays;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-nicole.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-nicole.dts
@@ -77,10 +77,9 @@ attention {
 	};

 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2500-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;
-		no-gpio-delays;

 		memory-region = <&coldfire_memory>;
 		aspeed,sram = <&sram>;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-palmetto.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-palmetto.dts
@@ -55,7 +55,7 @@ identify {
 	};

 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2400-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2400-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;

@@ -151,7 +151,7 @@ eeprom@50 {
 	};

 	rtc@68 {
-		compatible = "dallas,ds3231";
+		compatible = "maxim,ds3231";
 		reg = <0x68>;
 	};
 };
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-romulus.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-romulus.dts
@@ -68,10 +68,9 @@ power {
 	};

 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2500-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;
-		no-gpio-delays;

 		memory-region = <&coldfire_memory>;
 		aspeed,sram = <&sram>;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-witherspoon.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-witherspoon.dts
@@ -173,7 +173,7 @@ power-button {
 	};

 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;
 		no-gpio-delays;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-zaius.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-zaius.dts
@@ -64,7 +64,7 @@ event-checkstop {
 			linux,code = <ASPEED_GPIO(F, 7)>;
 		};

-		event-pcie-e2b-present{
+		event-pcie-e2b-present {
 			label = "pcie-e2b-present";
 			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(E, 7)>;
@@ -96,7 +96,7 @@ hdd_fault {
 	};

 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;
 		no-gpio-delays;
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-s6q.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-s6q.dts
@@ -509,7 +509,7 @@ U197_PCA9546_CH1: i2c@1 {
 			reg = <1>;

 			cpu0_pvccin@60 {
-				compatible = "isil,raa229004";
+				compatible = "renesas,raa229004";
 				reg = <0x60>;
 			};

@@ -530,7 +530,7 @@ U197_PCA9546_CH2: i2c@2 {
 			reg = <2>;

 			cpu1_pvccin@72 {
-				compatible = "isil,raa229004";
+				compatible = "renesas,raa229004";
 				reg = <0x72>;
 			};

--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman.dtsi
@@ -30,7 +30,7 @@ video_engine_memory: jpegbuffer {
 			reusable;
 		};

-		ramoops@9eff0000{
+		ramoops@9eff0000 {
 			compatible = "ramoops";
 			reg = <0x9eff0000 0x10000>;
 			record-size = <0x2000>;
--- a/arch/arm/boot/dts/aspeed/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g4.dtsi
@@ -356,7 +356,6 @@ vuart: serial@1e787000 {
 			lpc: lpc@1e789000 {
 				compatible = "aspeed,ast2400-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
-				reg-io-width = <4>;

 				#address-cells = <1>;
 				#size-cells = <1>;
--- a/arch/arm/boot/dts/aspeed/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g5.dtsi
@@ -273,7 +273,6 @@ hace: crypto@1e6e3000 {
 			gfx: display@1e6e6000 {
 				compatible = "aspeed,ast2500-gfx", "syscon";
 				reg = <0x1e6e6000 0x1000>;
-				reg-io-width = <4>;
 				clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
 				resets = <&syscon ASPEED_RESET_CRT1>;
 				syscon = <&syscon>;
@@ -441,7 +440,6 @@ vuart: serial@1e787000 {
 			lpc: lpc@1e789000 {
 				compatible = "aspeed,ast2500-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
-				reg-io-width = <4>;

 				#address-cells = <1>;
 				#size-cells = <1>;
--- a/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
@@ -412,6 +412,16 @@ pinctrl_mdio4_default: mdio4_default {
 		groups = "MDIO4";
 	};

+	pinctrl_ncsi3_default: ncsi3_default {
+		function = "RMII3";
+		groups = "NCSI3";
+	};
+
+	pinctrl_ncsi4_default: ncsi4_default {
+		function = "RMII4";
+		groups = "NCSI4";
+	};
+
 	pinctrl_ncts1_default: ncts1_default {
 		function = "NCTS1";
 		groups = "NCTS1";
--- a/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi
@@ -382,7 +382,6 @@ rng: hwrng@1e6e2524 {
 			gfx: display@1e6e6000 {
 				compatible = "aspeed,ast2600-gfx", "syscon";
 				reg = <0x1e6e6000 0x1000>;
-				reg-io-width = <4>;
 				clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
 				resets = <&syscon ASPEED_RESET_GRAPHICS>;
 				syscon = <&syscon>;
@@ -572,7 +571,6 @@ peci0: peci-controller@1e78b000 {
 			lpc: lpc@1e789000 {
 				compatible = "aspeed,ast2600-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
-				reg-io-width = <4>;

 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -662,7 +660,7 @@ sdc: sdc@1e740000 {
 				status = "disabled";

 				sdhci0: sdhci@1e740100 {
-					compatible = "aspeed,ast2600-sdhci", "sdhci";
+					compatible = "aspeed,ast2600-sdhci";
 					reg = <0x100 0x100>;
 					interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 					sdhci,auto-cmd12;
@@ -671,7 +669,7 @@ sdhci0: sdhci@1e740100 {
 				};

 				sdhci1: sdhci@1e740200 {
-					compatible = "aspeed,ast2600-sdhci", "sdhci";
+					compatible = "aspeed,ast2600-sdhci";
 					reg = <0x200 0x100>;
 					interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 					sdhci,auto-cmd12;
@@ -847,7 +845,7 @@ i2c: bus@1e78a000 {

 			fsim0: fsi@1e79b000 {
 				#interrupt-cells = <1>;
-				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
+				compatible = "aspeed,ast2600-fsi-master";
 				reg = <0x1e79b000 0x94>;
 				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 				pinctrl-names = "default";
@@ -859,7 +857,7 @@ fsim0: fsi@1e79b000 {

 			fsim1: fsi@1e79b100 {
 				#interrupt-cells = <1>;
-				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
+				compatible = "aspeed,ast2600-fsi-master";
 				reg = <0x1e79b100 0x94>;
 				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
 				pinctrl-names = "default";
--- a/arch/arm/boot/dts/aspeed/ast2600-facebook-netbmc-common.dtsi
+++ b/arch/arm/boot/dts/aspeed/ast2600-facebook-netbmc-common.dtsi
@@ -31,9 +31,13 @@ spi_gpio: spi {
 		#address-cells = <1>;
 		#size-cells = <0>;

-		gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+		/*
+		 * chipselect pins are defined in platform .dts files
+		 * separately.
+		 */
+		sck-gpios = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;

 		tpm@0 {
 			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
@@ -152,18 +156,6 @@ &vhub {
 	status = "okay";
 };

-&emmc_controller {
-	status = "okay";
-};
-
-&emmc {
-	status = "okay";
-
-	non-removable;
-	max-frequency = <25000000>;
-	bus-width = <4>;
-};
-
 &rtc {
 	status = "okay";
 };
--- a/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128-data64.dtsi
+++ b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128-data64.dtsi
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+partitions {
+	compatible = "fixed-partitions";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	/*
+	 * u-boot partition: 896KB.
+	 */
+	u-boot@0 {
+		reg = <0x0 0xe0000>;
+		label = "u-boot";
+	};
+
+	/*
+	 * u-boot environment variables: 64KB.
+	 */
+	u-boot-env@e0000 {
+		reg = <0xe0000 0x10000>;
+		label = "env";
+	};
+
+	/*
+	 * image metadata partition (64KB), used by Facebook internal
+	 * tools.
+	 */
+	image-meta@f0000 {
+		reg = <0xf0000 0x10000>;
+		label = "meta";
+	};
+
+	/*
+	 * FIT image: 63 MB.
+	 */
+	fit@100000 {
+		reg = <0x100000 0x3f00000>;
+		label = "fit";
+	};
+
+	/*
+	 * "data0" partition (64MB) is used by Facebook BMC platforms as
+	 * persistent data store.
+	 */
+	data0@4000000 {
+		reg = <0x4000000 0x4000000>;
+		label = "data0";
+	};
+
+	/*
+	 * Although the master partition can be created by enabling
+	 * MTD_PARTITIONED_MASTER option, below "flash0" partition is
+	 * explicitly created to avoid breaking legacy applications.
+	 */
+	flash0@0 {
+		reg = <0x0 0x8000000>;
+		label = "flash0";
+	};
+};
--- a/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
+++ b/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
@@ -82,6 +82,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam0_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -98,6 +99,7 @@ eeprom@0 {
 			};

 			cfam0_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -114,8 +116,8 @@ eeprom@0 {
 			};

 			cfam0_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -131,8 +133,8 @@ eeprom@0 {
 			};

 			cfam0_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -249,6 +251,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam1_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -265,6 +268,7 @@ eeprom@0 {
 			};

 			cfam1_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -281,8 +285,8 @@ eeprom@0 {
 			};

 			cfam1_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -298,8 +302,8 @@ eeprom@0 {
 			};

 			cfam1_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

--- a/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi
+++ b/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi
@@ -733,6 +733,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam2_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -749,6 +750,7 @@ eeprom@0 {
 			};

 			cfam2_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -765,8 +767,8 @@ eeprom@0 {
 			};

 			cfam2_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -782,8 +784,8 @@ eeprom@0 {
 			};

 			cfam2_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -1106,6 +1108,7 @@ fsi2spi@1c00 {
 			#size-cells = <0>;

 			cfam3_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1122,6 +1125,7 @@ eeprom@0 {
 			};

 			cfam3_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1138,8 +1142,8 @@ eeprom@0 {
 			};

 			cfam3_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

@@ -1155,8 +1159,8 @@ eeprom@0 {
 			};

 			cfam3_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible =  "ibm,fsi2spi";
 				#address-cells = <1>;
 				#size-cells = <0>;

--- a/arch/arm/boot/dts/broadcom/Makefile
+++ b/arch/arm/boot/dts/broadcom/Makefile
@@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_BCMBCA) += \
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4708-asus-rt-ac56u.dtb \
 	bcm4708-asus-rt-ac68u.dtb \
+	bcm4708-buffalo-wxr-1750dhp.dtb \
 	bcm4708-buffalo-wzr-1750dhp.dtb \
 	bcm4708-buffalo-wzr-1166dhp.dtb \
 	bcm4708-buffalo-wzr-1166dhp2.dtb \
--- a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wxr-1750dhp.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wxr-1750dhp.dts
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Taishi Shimizu <s.taishi14142@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "buffalo,wxr-1750dhp", "brcm,bcm4708";
+	model = "Buffalo WXR-1750DHP";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-aoss {
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		/* GPIO 3 is a switch button with AUTO / MANUAL. */
+		button-manual {
+			gpios = <&chipcommon 3 GPIO_ACTIVE_HIGH>;
+			label = "MANUAL";
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+
+		button-restart {
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+		};
+
+		/* GPIO 8 and 9 are a tri-state switch button with
+		 * ROUTER / AP / WB.
+		 */
+		button-router {
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			label = "ROUTER";
+			linux,code = <BTN_1>;
+			linux,input-type = <EV_SW>;
+		};
+
+		button-wb {
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+			label = "WB";
+			linux,code = <BTN_2>;
+			linux,input-type = <EV_SW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-internet {
+			color = <LED_COLOR_ID_WHITE>;
+			function = "internet";
+			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power0 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power1 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-router0 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = "router";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-router1 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = "router";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-usb {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_USB;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&xhci_port1 &ehci_port1 &ohci_port1>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+		};
+
+		port@1 {
+			label = "lan4";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan2";
+		};
+
+		port@4 {
+			label = "lan1";
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/cirrus/ep7211-edb7211.dts
+++ b/arch/arm/boot/dts/cirrus/ep7211-edb7211.dts
@@ -46,8 +46,8 @@ timing0: timing-320x240 {

 	i2c: i2c {
 		compatible = "i2c-gpio";
-		gpios = <&portd 4 GPIO_ACTIVE_HIGH>,
-			<&portd 5 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&portd 4 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&portd 5 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,delay-us = <2>;
 		i2c-gpio,scl-output-only;
 		#address-cells = <1>;
--- a/arch/arm/boot/dts/intel/ixp/Makefile
+++ b/arch/arm/boot/dts/intel/ixp/Makefile
@@ -1,5 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_IXP4XX) += \
+	intel-ixp42x-actiontec-mi424wr-ac.dtb \
+	intel-ixp42x-actiontec-mi424wr-d.dtb \
 	intel-ixp42x-linksys-nslu2.dtb \
 	intel-ixp42x-linksys-wrv54g.dtb \
 	intel-ixp42x-freecom-fsg-3.dtb \
--- a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-ac.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-ac.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the IXP425-based Actiontec MI424WR revision A and C
+ * Based on a board file from OpenWrt by Jose Vasconcellos.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x-actiontec-mi424wr.dtsi"
+
+/ {
+	model = "Actiontec MI424WR rev A/C";
+	compatible = "actiontec,mi424wr-ac", "intel,ixp42x";
+
+	soc {
+		/* EthB used for WAN */
+		ethernet@c8009000 {
+			phy-handle = <&phy17>; // 17 on revision A-C
+
+			mdio {
+				phy17: ethernet-phy@17 {
+					/* WAN */
+					reg = <17>;
+				};
+			};
+		};
+
+		/* EthC used for LAN */
+		ethernet@c800a000 {
+			/* Fixed link to the CPU MII port on the KS8995 */
+			fixed-link {
+				speed = <100>;
+				full-duplex;
+			};
+		};
+	};
+};
--- a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-d.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-d.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the IXP425-based Actiontec MI424WR revision D
+ * Based on a board file from OpenWrt by Jose Vasconcellos.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x-actiontec-mi424wr.dtsi"
+
+/ {
+	model = "Actiontec MI424WR rev D";
+	compatible = "actiontec,mi424wr-d", "intel,ixp42x";
+
+	soc {
+		/* EthB used for LAN */
+		ethernet@c8009000 {
+			/* Fixed link to the CPU MII port on the KS8995 */
+			fixed-link {
+				speed = <100>;
+				full-duplex;
+			};
+
+			mdio {
+				/* PHY ID 0x00221450 */
+				phy5: ethernet-phy@5 {
+					/* WAN */
+					reg = <5>;
+				};
+			};
+		};
+
+		/* EthC used for WAN */
+		ethernet@c800a000 {
+			phy-handle = <&phy5>; // 5 on revision D
+		};
+	};
+};
--- a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr.dtsi
@@ -0,0 +1,272 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the IXP425-based Actiontec MI424WR
+ * Based on a board file from OpenWrt by Jose Vasconcellos.
+ */
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart1:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-wan-coax {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "wan-coax";
+			gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-power-alarm {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_ALARM;
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-power {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+		led-wireless {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_WLAN;
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-internet-down {
+			color = <LED_COLOR_ID_RED>;
+			function = "internet-down";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-internet-up {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "internet-up";
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-lan-coax {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "lan-coax";
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-wan-ethernet-alarm {
+			color = <LED_COLOR_ID_RED>;
+			function = "wan-ethernet-alarm";
+			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		/* The last three LEDs are not mounted but traces exist on the PCB */
+		led-phone-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "phone-1";
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-phone-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "phone-2";
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-voip {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "voip";
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		ethernet-switch@0 {
+			compatible = "micrel,ks8995";
+			reg = <0>;
+			spi-max-frequency = <50000000>;
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethernet-port@0 {
+					reg = <0>;
+					label = "lan1";
+					phy-mode = "mii";
+					phy-handle = <&phy1>;
+				};
+				ethernet-port@1 {
+					reg = <1>;
+					label = "lan2";
+					phy-mode = "mii";
+					phy-handle = <&phy2>;
+				};
+				ethernet-port@2 {
+					reg = <2>;
+					label = "lan3";
+					phy-mode = "mii";
+					phy-handle = <&phy3>;
+				};
+				ethernet-port@3 {
+					reg = <3>;
+					label = "lan4";
+					phy-mode = "mii";
+					phy-handle = <&phy4>;
+				};
+				ethernet-port@4 {
+					reg = <4>;
+					ethernet = <&ethc>;
+					phy-mode = "mii";
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+
+			};
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of Flash in 64 0x20000 sized blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x0800000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					fis-index-block = <0x3f>;
+				};
+			};
+			gpio1: gpio@1,0 {
+				/* MMIO GPIO at CS1 */
+				compatible = "intel,ixp4xx-expansion-bus-mmio-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+				big-endian;
+				reg = <1 0x00000000 0x2>;
+				reg-names = "dat";
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				pci-reset-hog {
+					gpio-hog;
+					gpios = <7 GPIO_ACTIVE_HIGH>;
+					output-high;
+					line-name = "PCI reset";
+				};
+				pstn-relay-hog-1 {
+					gpio-hog;
+					gpios = <11 GPIO_ACTIVE_HIGH>;
+					output-low;
+					line-name = "PSTN relay control 1";
+				};
+				pstn-relay-hog-2 {
+					gpio-hog;
+					gpios = <12 GPIO_ACTIVE_HIGH>;
+					output-low;
+					line-name = "PSTN relay control 2";
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 13 */
+			<0x6800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 8 */
+			<0x6800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 6 */
+			/* IDSEL 14 */
+			<0x7000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */
+			<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 8 */
+			/* IDSEL 15 */
+			<0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 6 */
+			<0x7800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT B on slot 15 is irq 7 */
+		};
+
+		ethb: ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "mii";
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* 1, 2, 3 and 4 are ports on the KS8995 switch */
+				phy1: ethernet-phy@1 {
+					/* LAN1 */
+					reg = <1>;
+				};
+				phy2: ethernet-phy@2 {
+					/* LAN2 */
+					reg = <2>;
+				};
+				phy3: ethernet-phy@3 {
+					/* LAN3 */
+					reg = <3>;
+				};
+				phy4: ethernet-phy@4 {
+					/* LAN4 */
+					reg = <4>;
+				};
+			};
+		};
+
+		ethc: ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "mii";
+		};
+	};
+};
--- a/arch/arm/boot/dts/microchip/at91-sama7d65_curiosity.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama7d65_curiosity.dts
@@ -11,6 +11,8 @@
 #include "sama7d65-pinfunc.h"
 #include "sama7d65.dtsi"
 #include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/at91.h>

 / {
@@ -26,6 +28,43 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};

+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button {
+			label = "PB_USER";
+			gpios = <&pioa PIN_PC10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+
+		led0: led-red {
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pioa PIN_PB17 GPIO_ACTIVE_HIGH>; /* Conflict with pwm. */
+		};
+
+		led1: led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pioa PIN_PB15 GPIO_ACTIVE_HIGH>; /* Conflict with pwm. */
+		};
+
+		led2: led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&pioa PIN_PA21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
@@ -346,12 +385,24 @@ pinctrl_gmac0_txck_default: gmac0-txck-default {
 		bias-pull-up;
 	};

-	pinctrl_i2c10_default: i2c10-default{
+	pinctrl_i2c10_default: i2c10-default {
 		pinmux = <PIN_PB19__FLEXCOM10_IO1>,
 			 <PIN_PB20__FLEXCOM10_IO0>;
 		bias-pull-up;
 	};

+	pinctrl_key_gpio_default: key-gpio-default {
+		pinmux = <PIN_PC10__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led-gpio-default {
+		pinmux = <PIN_PB15__GPIO>,
+			 <PIN_PB17__GPIO>,
+			 <PIN_PA21__GPIO>;
+		bias-pull-up;
+	};
+
 	pinctrl_sdmmc1_default: sdmmc1-default {
 		cmd-data {
 			pinmux = <PIN_PB22__SDMMC1_CMD>,
--- a/arch/arm/boot/dts/microchip/sam9x7.dtsi
+++ b/arch/arm/boot/dts/microchip/sam9x7.dtsi
@@ -271,6 +271,27 @@ AT91_XDMAC_DT_PERID(38))>,
 			status = "disabled";
 		};

+		qspi: spi@f0014000 {
+			compatible = "microchip,sam9x7-ospi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xf0014000 0x100>, <0x60000000 0x20000000>;
+			reg-names = "qspi_base", "qspi_mmap";
+			interrupts = <35 IRQ_TYPE_LEVEL_HIGH 7>;
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				AT91_XDMAC_DT_PERID(26))>,
+				<&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				AT91_XDMAC_DT_PERID(27))>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_GCK 35>;
+			clock-names = "pclk", "gclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 35>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_PLLADIV2>;
+			status = "disabled";
+		};
+
 		i2s: i2s@f001c000 {
 			compatible = "microchip,sam9x7-i2smcc", "microchip,sam9x60-i2smcc";
 			reg = <0xf001c000 0x100>;
--- a/Show More
+++ b/Show More