Regulator/supply fixes for a number of boards, removed too fast
cpu OPPs from rk3576 (not supported in newer vendor TF-A and never
supported in upstream TF-A). As well as some DTS validation fixes
and one pinctrl fix for the odroid-m1.
* tag 'v6.18-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: fix PCIe 3.3V regulator voltage on orangepi-5
arm64: dts: rockchip: disable HS400 on RK3588 Tiger
arm64: dts: rockchip: drop reset from rk3576 i2c9 node
arm64: dts: rockchip: Fix USB power enable pin for BTT CB2 and Pi2
arm64: dts: rockchip: Fix vccio4-supply on rk3566-pinetab2
arm64: dts: rockchip: include rk3399-base instead of rk3399 in rk3399-op1
arm64: dts: rockchip: Fix indentation on rk3399 haikou demo dtso
arm64: dts: rockchip: Make RK3588 GPU OPP table naming less generic
arm64: dts: rockchip: Drop 'rockchip,grf' prop from tsadc on rk3328
arm64: dts: rockchip: Remove non-functioning CPU OPPs from RK3576
arm64: dts: rockchip: Fix PCIe power enable pin for BigTreeTech CB2 and Pi2
arm64: dts: rockchip: Set correct pinctrl for I2S1 8ch TX on odroid-m1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 6.18, please pull the following:
- Andrea assigns clocks rates for the Ethernet controller for the
Raspberry Pi 5 systems
- Laurent adds an ethernet0 alias to allow client programs consuming
that alias to populate the correct Ethernet address for the Raspberry
Pi 5 systems
* tag 'arm-soc/for-6.18/devicetree-arm64-fixes-v2' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: bcm2712: rpi-5: Add ethernet0 alias
arm64: dts: broadcom: Assign clock rates in eth node for RPi5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Fixes for v6.18
This contains a simple fix to mark the Ethernet PHY on Jetson Xavier NX
as a wakeup source so the device can support WoL.
* tag 'tegra-for-6.18-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Mark Jetson Xavier NX's PHY as a wakeup source
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We've had reports from the field that some RK3588 Tiger have random
issues with eMMC errors.
Applying commit a28352cf2d ("mmc: sdhci-of-dwcmshc: Change
DLL_STRBIN_TAPNUM_DEFAULT to 0x4") didn't help and seemed to have made
things worse for our board.
Our HW department checked the eMMC lines and reported that they are too
long and don't look great so signal integrity is probably not the best.
Note that not all Tigers with the same eMMC chip have errors, so the
suspicion is that we're really on the edge in terms of signal integrity
and only a handful devices are failing. Additionally, we have RK3588
Jaguars with the same eMMC chip but the layout is different and we also
haven't received reports about those so far.
Lowering the max-frequency to 150MHz from 200MHz instead of simply
disabling HS400 was briefly tested and seem to work as well. We've
disabled HS400 downstream and haven't received reports since so we'll go
with that instead of lowering the max-frequency.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Fixes: 6173ef24b3 ("arm64: dts: rockchip: add RK3588-Q7 (Tiger) SoM")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251112-tiger-hs200-v1-1-b50adac107c0@cherry.de
[added Fixes tag and stable-cc from 2nd mail]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In Raspberry Pi 5 DTS, the Ethernet clock rates must be assigned
as the default clock register values are not valid for the
Ethernet interface to function.
This can be done either in rp1_clocks node or in rp1_eth node.
Define the rates in rp1_eth node, as those clocks are 'leaf' clocks
used specifically by the Ethernet device only.
Fixes: 43456fdfc0 ("arm64: dts: broadcom: Enable RP1 ethernet for Raspberry Pi 5")
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20251021135533.5517-1-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
In commit 296602b8e5 ("arm64: dts: rockchip: Move RK3399 OPPs to dtsi
files for SoC variants"), everything shared between variants of RK3399
was put into rk3399-base.dtsi and the rest in variant-specific DTSI,
such as rk3399-t, rk3399-op1, rk3399, etc.
Therefore, the variant-specific DTSI should include rk3399-base.dtsi and
not another variant's DTSI.
rk3399-op1 wrongly includes rk3399 (a variant) DTSI instead of
rk3399-base DTSI, let's fix this oversight by including the intended
DTSI.
Fortunately, this had no impact on the resulting DTB since all nodes
were named the same and all node properties were overridden in
rk3399-op1.dtsi. This was checked by doing a checksum of rk3399-op1 DTBs
before and after this commit.
No intended change in behavior.
Fixes: 296602b8e5 ("arm64: dts: rockchip: Move RK3399 OPPs to dtsi files for SoC variants")
Cc: stable@vger.kernel.org
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://patch.msgid.link/20251029-rk3399-op1-include-v1-1-2472ee60e7f8@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The VBUS supply regulator is currently assigned to the PHY node.
This causes the VBUS to be always on, even when the controller
needs to be switched to peripheral mode.
Fix the OTG role switching by adding a connector node and moving
the VBUS supply regulator to that node. This way the VBUS gets
correctly switched according to the current role.
Fixes: 946ab10e3f ("arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier board")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The msi-map property was incorrectly applied to pcie0-ep instead of
pcie1-ep. Correct the msi-map for both pcie0-ep and pcie1-ep nodes.
Fixes: bbe4b2f7d6 ("arm64: dts: imx95: Add msi-map for pci-ep device")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The gpio0_mipi_csi DT nodes are enabled by default, but they are
dependent on the irqsteer_csi nodes, which are not enabled. This causes
the gpio0_mipi_csi GPIOs to be probe deferred. Since these GPIOs can be
used independently of the CSI controller, enable irqsteer_csi by default
too to prevent them from being deferred and to ensure they work out of
the box.
Fixes: 2217f82437 ("arm64: dts: imx8: add capture controller for i.MX8's img subsystem")
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mark the RTL8211F PHY as a wakeup source for the Jetson Xavier NX.
This allows the reworked RTL8211F driver to know that the PHY is
wired to wakeup capable hardware, and thus to expose WoL capabilities.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unify the naming of the existing GPU OPP table nodes found in the RK3588
and RK3588J SoC dtsi files with the other SoC's GPU OPP nodes, following
the more "modern" node naming scheme.
Fixes: a7b2070505 ("arm64: dts: rockchip: Split GPU OPPs of RK3588 and RK3588j")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
[opp-table also is way too generic on systems with like 4-5 opp-tables]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 'rockchip,grf' property for tsadc in rk3328 wasn't actually used in
the driver and is no longer allowed in the DT since commit
e881662aa0 ("dt-bindings: thermal: rockchip: Tighten grf requirements")
So remove that property which fixes the following DT validation issue
tsadc@ff250000 (rockchip,rk3328-tsadc): rockchip,grf: False schema does not allow [[58]]
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable proper pin multiplexing for the I2S1 8-channel transmit interface by
adding the default pinctrl configuration which esures correct signal routing
and avoids pinmux conflicts during audio playback.
Changes fix the error
[ 116.856643] [ T782] rockchip-pinctrl pinctrl: pin gpio1-10 already requested by affinity_hint; cannot claim for fe410000.i2s
[ 116.857567] [ T782] rockchip-pinctrl pinctrl: error -EINVAL: pin-42 (fe410000.i2s)
[ 116.857618] [ T782] rockchip-pinctrl pinctrl: error -EINVAL: could not request pin 42 (gpio1-10) from group i2s1m0-sdi1 on device rockchip-pinctrl
[ 116.857659] [ T782] rockchip-i2s-tdm fe410000.i2s: Error applying setting, reverse things back
I2S1 on the M1 to the codec in the RK809 only uses the SCLK, LRCK, SDI0
and SDO0 signals, so limit the claimed pins to those.
With this change audio output works as expected:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDMI], device 0: fe400000.i2s-i2s-hifi i2s-hifi-0 [fe400000.i2s-i2s-hifi i2s-hifi-0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: RK817 [Analog RK817], device 0: fe410000.i2s-rk817-hifi rk817-hifi-0 [fe410000.i2s-rk817-hifi rk817-hifi-0]
Subdevices: 1/1
Subdevice #0: subdevice #0
Fixes: 78f858447c ("arm64: dts: rockchip: Add analog audio on ODROID-M1")
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
[adapted the commit message a bit]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull x86 platform driver updates from Ilpo Järvinen:
- amd/pmf:
- Add support for adjusting PMF PPT and PPT APU thresholds
- Extend custom BIOS inputs for more policies
- Update ta_pmf_action structure to the latest PMF TA
- arm64:
- thinkpad-t14s-ec: Add EC driver for ThinkPad T14s Gen6 Snapdragon
- int3472:
- Increase handshake GPIO delay
- intel/pmc:
- SSRAM support for Lunar Lake and Panther Lake
- Support reading substate requirements data from S0ix blockers
(for platforms starting from Panther Lake)
- Wildcat Lake support
- intel-uncore-freq:
- Solve duplicate sysfs entry warnings
- Present unique domain ID per package
- portwell-ec:
- Support suspend/resume
- Add hwmon support for voltage and temperature
- redmi-wmi:
- Add WMI driver for Redmibook keyboard
- think-lmi:
- Certificate support for ThinkCenter
- x86-android-tables + others:
- Convert away from legacy GPIO APIs
- x86-android-tables:
- Add support for Acer A1-840 tablet
- Fix modules list for Lenovo devices
- Stop using EPROBE_DEFER
- Miscellaneous cleanups / refactoring / improvements
* tag 'platform-drivers-x86-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (63 commits)
platform/x86: pcengines-apuv2: Use static device properties
platform/x86: meraki-mx100: Use static device properties
platform/x86: barco-p50-gpio: use software nodes for gpio-leds/keys
platform/x86: x86-android-tablets: Stop using EPROBE_DEFER
platform/x86: x86-android-tablets: Fix modules lists for Lenovo devices
platform/x86: x86-android-tablets: Simplify lenovo_yoga_tab2_830_1050_exit()
platform/x86: x86-android-tablets: Add support for Acer A1-840 tablet
platform/x86: x86-android-tablets: Move Acer info to its own file
platform/x86: x86-android-tablets: Update my email address
platform/x86: x86-android-tablets: Simplify node-group [un]registration
platform/x86: x86-android-tablets: use swnode_group instead of manual registering
platform/x86: x86-android-tablets: replace bat_swnode with swnode_group
platform/x86: x86-android-tablets: convert gpio_keys devices to GPIO references
platform/x86: x86-android-tablets: remove support for GPIO lookup tables
platform/x86: x86-android-tablets: convert Yoga Tab2 fast charger to GPIO references
platform/x86: x86-android-tablets: convert HID-I2C devices to GPIO references
platform/x86: x86-android-tablets: convert wm1502 devices to GPIO references
platform/x86: x86-android-tablets: convert int3496 devices to GPIO references
platform/x86: x86-android-tablets: convert EDT devices to GPIO references
platform/x86: x86-android-tablets: convert Novatek devices to GPIO references
...
Pull SoC dt updates from Arnd Bergmann:
"There are five sets of new SoCs that get added in existing families,
all of them being either upgrades or cut-down versions of the older
chips:
- Apple M2 Pro, M2 Max and M2 Ultra, used in the 2022/2023 generation
of high-end workstations and laptops from Apple. Linux has been
working on these for a while but stil requires patches.
- Axis Artpec8 is an Armv8 chip based on Samsung Exynos design,
unlike the earlier Armv7 Artpec6 from the same company that was
part of a separate family of chips.
- NXP i.MX91 is a cut-down version of i.MX93, using only a single
Cortex-A55 core.
- Qualcomm Lemans Auto is a variant of the Lemans SoC that was
originally merged under the sa8775p name, the differences being
mostly the firmware configuration of the platform.
- Four new Renesas SoCs RZ/T2H (r9a09g077m44), RZ/N2H (r9a09g087m44),
RZ/T2H (r9a09g077), and RZ/N2H (r9a09g087) are all industrial
bedded SoCs based on Cortex-A55 cores
In total, there are 65 new machines, including:
- Industrial embedded system and single-board computers based on NXP,
Allwinner, TI, Rockchips, Marvell, Xilinx Spacemit, Starfive chips.
- Reference boards for the newly added Renesas, Qualcomm, NXP and
Axis ARMv8 chips as well as Microchip's MPFS RISC-V SoC
- Laptops and Workstations using Apple M2 and Qualcomm Snapdragon X1
chips.
- Several Samsung phones using Qualcomm Snapdragon chips
- Set-top boxes based on Allwinner H313
- Five BMC boards using 32-bit ASpeed SoCs
- Three network routers using IXP4xx (ARMv5!) and Broadcom bcm4708
(ARMv7) SoCs
Two machines get phased out because they were available only in small
quantities but never made it into products: one STi407 based reference
board, and a Snapdragon 845 based Chromebook.
Aside from the newly added machines, a lot of work went into improving
hardware support on the existing machines and cleaning up contents for
validation"
* tag 'soc-dt-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (931 commits)
arm64: dts: apm-shadowcat: Drop "apm,xgene2-pcie" compatible
arm64: dts: apm-shadowcat: Move slimpro nodes out of "simple-bus" node
ARM: dts: microchip: sam9x7: Add qspi controller
arm64: dts: qcom: Add MST pixel streams for displayport
arm64: dts: qcom: sm6350: correct DP compatibility strings
arm64: dts: qcom: monaco-evk: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300-ride: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300: Add gpu and gmu nodes
arm64: dts: allwinner: h313: Add Amediatech X96Q
dt-bindings: arm: sunxi: Add Amediatech X96Q
arm64: dts: apple: t8015: Add SPMI node
arm64: dts: apple: t8012: Add SPMI node
arm64: dts: apple: Add J180d (Mac Pro, M2 Ultra, 2023) device tree
arm64: dts: rockchip: Add devicetree for the ROC-RK3588-RT
dt-bindings: arm: rockchip: Add Firefly ROC-RK3588-RT
arm64: dts: rockchip: update pinctrl names for Radxa E52C
arm64: dts: rockchip: remove vcc_3v3_pmu regulator for Radxa E52C
arm64: dts: apple: Add J474s, J475c and J475d device trees
arm64: dts: apple: Add J414 and J416 Macbook Pro device trees
arm64: dts: apple: Add initial t6020/t6021/t6022 DTs
...
Pull power management updates from Rafael Wysocki:
"The majority of these are cpufreq changes, which has been a recurring
pattern for a few recent cycles.
Those changes include new hardware support (AN7583 SoC support in the
airoha cpufreq driver, ipq5424 support in the qcom-nvmem cpufreq
driver, MT8196 support in the mediatek cpufreq driver, AM62D2 support
in the ti cpufreq driver), DT bindings and Rust code updates, cleanups
of the core and governors, and multiple driver fixes and cleanups.
Beyond that, there are hibernation fixes (some remaining 6.16 cycle
fallout and an issue related to hybrid suspend in the amdgpu driver),
cleanups of the PM core code, runtime PM documentation update, cpuidle
and power capping cleanups, and tooling updates.
Specifics:
- Rearrange variable declarations involving __free() in the cpufreq
core and intel_pstate driver to follow common coding style (Rafael
Wysocki)
- Fix object lifecycle issue in update_qos_request(), rearrange freq
QoS updates using __free(), and adjust frequency percentage
computations in the intel_pstate driver (Rafael Wysocki)
- Update intel_pstate to allow it to enable HWP without EPP if the
new DEC (Dynamic Efficiency Control) HW feature is enabled (Rafael
Wysocki)
- Use on_each_cpu_mask() in drv_write() in the ACPI cpufreq driver to
simplify the code (Rafael Wysocki)
- Use likely() optimization in intel_pstate_sample() (Yaxiong Tian)
- Remove dead EPB-related code from intel_pstate (Srinivas
Pandruvada)
- Use scope-based cleanup for cpufreq policy references in multiple
cpufreq drivers (Zihuan Zhang)
- Avoid calling get_governor() for the first policy in the cpufreq
core to simplify the initial policy path (Zihuan Zhang)
- Clean up the cpufreq core in multiple places (Zihuan Zhang)
- Use int type to store negative error codes in the cpufreq core and
update the speedstep-lib to use int for error codes (Qianfeng Rong)
- Update the efficient idle check for Intel extended Families in the
ondemand cpufreq governor (Sohil Mehta)
- Replace sscanf() with kstrtouint() in the conservative cpufreq
governor (Kaushlendra Kumar)
- Rename CpumaskVar::as[_mut]_ref to from_raw[_mut] in the cpumask
Rust code and mark CpumaskVar as transparent (Alice Ryhl, Baptiste
Lepers)
- Update ARef and AlwaysRefCounted imports from sync::aref in the OPP
Rust code (Shankari Anand)
- Add support for AN7583 SoC to the airoha cpufreq driver (Christian
Marangi)
- Enable cpufreq for ipq5424 in the qcom-nvmem cpufreq driver (Md
Sadre Alam)
- Add support for MT8196 to the mediatek-hw cpufreq driver, refactor
that driver and add mediatek,mt8196-cpufreq-hw DT binding (Nicolas
Frattaroli)
- Avoid redundant conditions in the mediatek cpufreq driver (Liao
Yuanhong)
- Add support for AM62D2 to the ti cpufreq driver and blocklist
ti,am62d2 SoC in dt-platdev (Paresh Bhagat)
- Support more speed grades on AM62Px SoC in the ti cpufreq driver,
allow all silicon revisions to support OPPs in it, and fix
supported hardware for 1GHz OPP (Judith Mendez)
- Add QCS615 compatible to DT bindings for cpufreq-qcom-hw (Taniya
Das)
- Minor assorted updates of the scmi, longhaul, CPPC, and armada-37xx
cpufreq drivers (Akhilesh Patil, BowenYu, Dennis Beier, and Florian
Fainelli)
- Remove outdated cpufreq-dt.txt (Frank Li)
- Fix python gnuplot package names in the amd_pstate_tracer utility
(Kuan-Wei Chiu)
- Saravana Kannan will maintain the virtual-cpufreq driver (Saravana
Kannan)
- Prevent CPU capacity updates after registering a perf domain from
failing on a first CPU that is not present (Christian Loehle)
- Add support for the cases in which frequency alone is not
sufficient to uniquely identify an OPP (Krishna Chaitanya Chundru)
- Use to_result() for OPP error handling in Rust (Onur Özkan)
- Add support for LPDDR5 on Rockhip RK3588 SoC to rockchip-dfi
devfreq driver (Nicolas Frattaroli)
- Fix an issue where DDR cycle counts on RK3588/RK3528 with LPDDR4(X)
are reported as half by adding a cycle multiplier to the DFI driver
in rockchip-dfi devfreq-event driver (Nicolas Frattaroli)
- Fix missing error pointer dereference check of regulator instance
in the mtk-cci devfreq driver probe and remove a redundant
condition from an if () statement in that driver (Dan Carpenter,
Liao Yuanhong)
- Fail cpuidle device registration if there is one already to avoid
sysfs-related issues (Rafael Wysocki)
- Use sysfs_emit()/sysfs_emit_at() instead of sprintf()/scnprintf()
in cpuidle (Vivek Yadav)
- Fix device and OF node leaks at probe in the qcom-spm cpuidle
driver and drop unnecessary initialisations from it (Johan Hovold)
- Remove unnecessary address-of operators from the intel_idle cpuidle
driver (Kaushlendra Kumar)
- Rearrange main loop in menu_select() to make the code in that
funtion easier to follow (Rafael Wysocki)
- Convert values in microseconds to ktime using us_to_ktime() where
applicable in the intel_idle power capping driver (Xichao Zhao)
- Annotate loops walking device links in the power management core
code as _srcu and add macros for walking device links to reduce the
likelihood of coding mistakes related to them (Rafael Wysocki)
- Document time units for *_time functions in the runtime PM API
(Brian Norris)
- Clear power.must_resume in noirq suspend error path to avoid
resuming a dependant device under a suspended parent or supplier
(Rafael Wysocki)
- Fix GFP mask handling during hybrid suspend and make the amdgpu
driver handle hybrid suspend correctly (Mario Limonciello, Rafael
Wysocki)
- Fix GFP mask handling after aborted hibernation in platform mode
and combine exit paths in power_down() to avoid code duplication
(Rafael Wysocki)
- Use vmalloc_array() and vcalloc() in the hibernation core to avoid
open-coded size computations (Qianfeng Rong)
- Fix typo in hibernation core code comment (Li Jun)
- Call pm_wakeup_clear() in the same place where other functions that
do bookkeeping prior to suspend_prepare() are called (Samuel Wu)
- Fix and clean up the x86_energy_perf_policy utility and update its
documentation (Len Brown, Kaushlendra Kumar)
- Fix incorrect sorting of PMT telemetry in turbostat (Kaushlendra
Kumar)
- Fix incorrect size in cpuidle_state_disable() and the error return
value of cpupower_write_sysfs() in cpupower (Kaushlendra Kumar)"
* tag 'pm-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
PM: hibernate: Combine return paths in power_down()
PM: hibernate: Restrict GFP mask in power_down()
PM: hibernate: Fix pm_hibernation_mode_is_suspend() build breakage
PM: runtime: Documentation: ABI: Document time units for *_time
tools/power x86_energy_perf_policy.8: Emphasize preference for SW interfaces
tools/power x86_energy_perf_policy: Add make snapshot target
tools/power x86_energy_perf_policy: Prefer driver HWP limits
tools/power x86_energy_perf_policy: EPB access is only via sysfs
tools/power x86_energy_perf_policy: Prepare for MSR/sysfs refactoring
tools/power x86_energy_perf_policy: Enhance HWP enable
tools/power x86_energy_perf_policy: Enhance HWP enabled check
tools/power x86_energy_perf_policy: Fix incorrect fopen mode usage
tools/power turbostat: Fix incorrect sorting of PMT telemetry
drm/amd: Fix hybrid sleep
PM: hibernate: Add pm_hibernation_mode_is_suspend()
PM: hibernate: Fix hybrid-sleep
tools/cpupower: Fix incorrect size in cpuidle_state_disable()
tools/power/x86/amd_pstate_tracer: Fix python gnuplot package names
cpufreq: Replace pointer subtraction with iteration macro
cpuidle: Fail cpuidle device registration if there is one already
...
CIX device tree changes for v6.18-rc1:
- arm64: dts: cix: add DT nodes for all I2C and I3C ports for sky1
* tag 'cix-dt-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/cix:
arm64: dts: cix: add DT nodes for all I2C and I3C ports for sky1
Link: https://lore.kernel.org/r/aNIyhPSV6lJaZIvR@nchen-desktop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
One new board the ROC-RK3588-RT, gpu improvements for RK3328, frequency
scaling for the RK3528 and the very first small steps for camera
support on the RK3588 - with the CSI-DPHY support, with more hopefully
to come soon'ish :-) .
And apart from those bigger points, some more individual peripheral work
on some boards.
* tag 'v6.18-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add devicetree for the ROC-RK3588-RT
dt-bindings: arm: rockchip: Add Firefly ROC-RK3588-RT
arm64: dts: rockchip: update pinctrl names for Radxa E52C
arm64: dts: rockchip: remove vcc_3v3_pmu regulator for Radxa E52C
arm64: dts: rockchip: Add USB and charger to Gameforce Ace
arm64: dts: rockchip: enable the Mali GPU on RK3328 boards
arm64: dts: rockchip: add GPU powerdomain, opps, and cooling to rk3328
arm64: dts: rockchip: Fix network on rk3576 evb1 board
arm64: dts: rockchip: add mipi csi-2 dphy nodes to rk3588
dt-bindings: soc: rockchip: add rk3588 csidphy grf syscon
arm64: dts: rockchip: Add rk3528 CPU frequency scaling support
arm64: dts: rockchip: enable HDMI Receiver on NanoPC T6
Link: https://lore.kernel.org/r/2079092.kXSN5OTJKJ@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
More Qualocmm Arm64 DeviceTree updates for v6.18
Introduce the Hamoa IoT SOM and the Hamoa EVK board, the HP Omnibook
X14, the Particle Tachyon board, and the Samsung Galaxy S22.
On IPQ5018 another set of UART and I2C controllers are added.
On Lemans SDHCI and the camera subsystem is introduced, the USB
controllers are updated to the new flattened binding.
The Lemans EVK gains Ethernet definition, more QUP controllers and their
GPI DMA engines are defined. PCIe, SDHCI, remoteproc and iris video
accelerator are added as well.
On the Monaco platform GPU and GMU are introduced, the USB controller
nodes are updated to the new flattened binding. The GPU is enabled on
the EVK and the Ride boards.
SDCC and MDSS resets are defined on MSM8916, MSM8939 also gets the MDSS
reset.
On QCM2290 the camera clock interface is added.
On the QCS615 tsens and related thermal-zones are introduced.
On SDM845 the OnePlus 6 gains notifications LED, and the sensor core
(SLPI) is enabled on the Samsung Galaxy S9.
WiFi and Bluetooth is enabled on the SM8750 MTP.
The IRIS video accelerator is introduce for X Elite and enabled on a
variety of laptops.
DisplayPort controllers on a variety of boards are updated to describe
additional pixel clocks, used for MST.
* tag 'qcom-arm64-for-6.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (57 commits)
arm64: dts: qcom: Add MST pixel streams for displayport
arm64: dts: qcom: sm6350: correct DP compatibility strings
arm64: dts: qcom: monaco-evk: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300-ride: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300: Add gpu and gmu nodes
dt-bindings: arm: qcom: sort sm8450 boards
arm64: dts: qcom: Add base HAMOA-IOT-EVK board
arm64: dts: qcom: Add HAMOA-IOT-SOM platform
dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board
arm64: dts: qcom: sm8750-mtp: Add WiFi and Bluetooth
arm64: dts: qcom: msm8953-xiaomi-daisy: fix cd-gpios
arm64: dts: qcom: ipq5018: add QUP1 UART2 node
arm64: dts: qcom: lemans: Flatten usb controller nodes
arm64: dts: qcom: qcs615: Enable TSENS support for QCS615 SoC
arm64: dts: qcom: sdm845-enchilada: Add notification LED
arm64: dts: qcom: apq8016-sbc: Drop redundant HDMI bridge status
arm64: dts: qcom: apq8016-sbc: Correct HDMI bridge #sound-dai-cells
arm64: dts: qcom: lemans: Add PCIe lane equalization preset properties
arm64: dts: qcom: sm8450: enable camera clock controller by default
arm64: dts: qcom: qcm2290: Add CCI node
...
Link: https://lore.kernel.org/r/20250921022346.598294-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apple SoC DTS updates for 6.18, part 2
- New device trees for all M2 Pro, Max and Ultra models are added.
This is responsible for most of the changed lines since we already
need 2000+ lines just to describe all the power domains inside
t602x-pmgr.dtsi for these SoCs.
- Missing WiFi properties for t600x are added.
- Bluetooth nodes are added for all t600x machines.
- The PCIe ethernet iommu-map was fixed for the Apple M1 iMac
to account for a disabled PCIe port.
- SPMI, NVMe, SART and mailbox nodes for Apple's T2 and A11.
* tag 'apple-soc-dt-6.18-part2' of https://git.kernel.org/pub/scm/linux/kernel/git/sven/linux:
arm64: dts: apple: t8015: Add SPMI node
arm64: dts: apple: t8012: Add SPMI node
arm64: dts: apple: Add J180d (Mac Pro, M2 Ultra, 2023) device tree
arm64: dts: apple: Add J474s, J475c and J475d device trees
arm64: dts: apple: Add J414 and J416 Macbook Pro device trees
arm64: dts: apple: Add initial t6020/t6021/t6022 DTs
arm64: dts: apple: Add ethernet0 alias for J375 template
dt-bindings: arm: apple: Add t6020x compatibles
arm64: dts: apple: t8015: Add NVMe nodes
arm64: dts: apple: t8015: Fix PCIE power domains dependencies
arm64: dts: apple: Add devicetreee for t8112-j415
dt-bindings: arm: apple: Add t8112 j415 compatible
arm64: dts: apple: t600x: Add bluetooth device nodes
arm64: dts: apple: t600x: Add missing WiFi properties
arm64: dts: apple: t8103-j457: Fix PCIe ethernet iommu-map
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The "apm,xgene2-pcie" compatible is unused, undocumented, and in the
wrong position in the compatible list. Given this is a mature and little
used platform, just remove the compatible rather than fix the order and
document it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250919161529.1293151-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Another missing supply and a wrong headphone gpio level.
* tag 'v6.17-rockchip-dtsfixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix the headphone detection on the orangepi 5
arm64: dts: rockchip: Add vcc supply for SPI Flash on NanoPC-T6
Amlogic ARM64 DT for v6.18:
- Add cache information to the Amlogic SoCs
- Add RTC node for Amlogic C3 SoC
- Fix PWM node for Amlogic C3 SoC
- Remove UHS capability for Odroid-C2 SDCard
* tag 'amlogic-arm64-dt-for-v6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: amlogic: gxbb-odroidc2: remove UHS capability for SD card
dts: arm: amlogic: fix pwm node for c3
arm64: dts: amlogic: sm1-bananapi: lower SD card speed for stability
arm64: dts: amlogic: Add cache information to the Amlogic T7 SoC
arm64: dts: amlogic: Add cache information to the Amlogic S922X SoC
arm64: dts: amlogic: Add cache information to the Amlogic S7 SoC
arm64: dts: amlogic: Add cache information to the Amlogic C3 SoC
arm64: dts: amlogic: Add cache information to the Amlogic A4 SoC
arm64: dts: amlogic: Add cache information to the Amlogic A1 SoC
arm64: dts: amlogic: Add cache information to the Amlogic GXM SoCS
arm64: dts: amlogic: Add cache information to the Amlogic AXG SoCS
arm64: dts: amlogic: Add cache information to the Amlogic G12A SoCS
arm64: dts: amlogic: Add cache information to the Amlogic SM1 SoC
arm64: dts: amlogic: Add cache information to the Amlogic GXBB and GXL SoC
arm64: dts: amlogic: C3: Add RTC controller node
Link: https://lore.kernel.org/r/d40e7e96-4a7c-4e4f-b36f-750c6525b95c@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Another missing supply and a wrong headphone gpio level.
* tag 'v6.17-rockchip-dtsfixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix the headphone detection on the orangepi 5
arm64: dts: rockchip: Add vcc supply for SPI Flash on NanoPC-T6
arm64: dts: rockchip: fix second M.2 slot on ROCK 5T
arm64: dts: rockchip: fix USB on RADXA ROCK 5T
arm64: dts: rockchip: Add vcc-supply to SPI flash on Pinephone Pro
arm64: dts: rockchip: fix es8388 address on rk3588s-roc-pc
arm64: dts: rockchip: Fix Bluetooth interrupts flag on Neardi LBA3368
arm64: dts: rockchip: correct network description on Sige5
arm64: dts: rockchip: Minor whitespace cleanup
ARM: dts: rockchip: Minor whitespace cleanup
arm64: dts: rockchip: Add supplies for eMMC on rk3588-orangepi-5
arm64: dts: rockchip: Fix the headphone detection on the orangepi 5 plus
arm64: dts: rockchip: Add vcc-supply to SPI flash on rk3399-pinebook-pro
arm64: dts: rockchip: mark eeprom as read-only for Radxa E52C
Allwinner Device Tree changes for 6.18
This tag contains two DT binding header changes that are shared with
the clk tree.
In this cycle we gained support for the MCU PRCM clock and reset
controller on the A523/A527/T527 family of SoCs, the NPU which is a
Vivante GC9000 IP block, and the NPU clock that was missing. The other
PRCM clock controller gained default bus clock rate settings. These
were not configured in the upstream U-boot bootloader, leading to them
running at slower rates. The assigned rates are from the user manual.
There is also a new board, the NetCube Systems Nagami SoM and two of
its carrier boards.
The A523 family development boards now have their internal RTC clocks
configured correctly, so that the RTC does not drift wildly. The missing
functions for the AXP717 on these boards are added. Missing reset GPIOs
and delays for Ethernet PHYs are added. Last, the Cubie A5E now has its
LEDs described and usable.
An overlay for the Orange Pi Zero interface (addon) board was added.
This can be used with the Orange Pi Zero and Zero Plus 2. Default audio
routing for these two boards (to be used with the addon) were added to
complement the overlay.
* tag 'sunxi-dt-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: sun55i: Complete AXP717A sub-functions
arm64: dts: allwinner: t527: orangepi-4a: hook up external 32k crystal
arm64: dts: allwinner: t527: avaota-a1: hook up external 32k crystal
arm64: dts: allwinner: a527: cubie-a5e: Drop external 32.768 KHz crystal
arm64: dts: sun55i: a523: Assign standard clock rates to PRCM bus clocks
ARM: dts: sunxi: add support for NetCube Systems Nagami Keypad Carrier
ARM: dts: sunxi: add support for NetCube Systems Nagami Basic Carrier
ARM: dts: sunxi: add support for NetCube Systems Nagami SoM
riscv: dts: allwinner: d1s-t113: Add pinctrl's required by NetCube Systems Nagami SoM
dt-bindings: arm: sunxi: Add NetCube Systems Nagami SoM and carrier board bindings
ARM: dts: allwinner: Add Orange Pi Zero Interface Board overlay
ARM: dts: allwinner: orangepi-zero-plus2: Add default audio routing
ARM: dts: allwinner: orangepi-zero: Add default audio routing
arm64: dts: allwinner: a523: Add NPU device node
arm64: dts: allwinner: a523: Add MCU PRCM CCU node
dt-bindings: clock: sun55i-a523-ccu: Add A523 MCU CCU clock controller
dt-bindings: clock: sun55i-a523-ccu: Add missing NPU module clock
arm64: dts: allwinner: t527: avaota-a1: Add ethernet PHY reset setting
arm64: dts: allwinner: a527: cubie-a5e: Add ethernet PHY reset setting
arm64: dts: allwinner: a527: cubie-a5e: Add LEDs
Link: https://lore.kernel.org/r/aMrtuZg8HlR--TAt@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SM6350 doesn't have MST support, as such in DT schema it has been
switched to use SC7180 as a fallback compatible. Make DT file implement
this change. DisplayPort on SC7180 has been supported long ago (and long
before we added support for DP on SM8350). The driver will continue to
work with the old DTS (having qcom,sm8350-dp fallback compatible) as
even after adding MST support the driver will have to support old SM8350
DTS which didn't have MST clocks.
Fixes: 62f87a3cac ("arm64: dts: qcom: sm6350: Add DisplayPort controller")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250916-dp_mst_bindings-v9-1-68c674b39d8e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The M2 Ultra in the Mac Pro differs from the M2 Ultra Mac Studio in its
PCIe setup. It uses all available 16 PCIe Gen4 on the first die and 8
PCIe Gen4 lanes on the second die to connect to a 100 lane Microchip
Switchtec PCIe switch. All internal PCIe devices and the PCIe slots are
connected to the PCIe switch.
Each die implements a PCIe controller with a single 16 or 8 lane port.
The PCIe controller is mostly compatible with existing implementation
in pcie-apple.c.
The resources for other 8 lanes on the second die are used to connect
the NVMe flash with the controller in the SoC.
This initial device tree does not include PCIe support.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Co-developed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Sven Peter <sven@kernel.org>
Signed-off-by: Sven Peter <sven@kernel.org>
