Some drivers like iwlwifi might have per-STA queues, so we
may want to flush/drop just those queues rather than all
when removing a station. Add a separate method for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we remove a station, we first make it unreachable,
then we (must) remove its keys, and then remove the
station itself. Depending on the hardware design, if
we have hardware crypto at all, frames still sitting
on hardware queues may then be transmitted without a
valid key, possibly unencrypted or with a fixed key.
Fix this by flushing the queues when removing stations
so this cannot happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The checks of whether or not a frame is bufferable were not
taking into account that some action frames aren't, such as
FTM. Check this, which requires some changes to the function
ieee80211_is_bufferable_mmpdu() since we need the whole skb
for the checks now.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WLAN_PUBLIC_ACTION_FTM_RESPONSE is duplicated with
WLAN_PUB_ACTION_FTM, but that might better be called
WLAN_PUB_ACTION_FTM_RESPONSE; clean up here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For SDIO host controllers with DMA support the TX buffer physical memory
address need to be aligned at an 8-byte boundary. Reserve 8 bytes of
extra TX headroom so we can align the data without re-allocating the
transmit buffer.
While here, also remove the TODO comment regarding extra headroom for
USB and SDIO. For SDIO the extra headroom is now handled and for USB it
was not needed so far.
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-6-martin.blumenstingl@googlemail.com
Add a sub-driver for SDIO based chipsets which implements the following
functionality:
- register accessors for 8, 16 and 32 bits for all states of the card
(including usage of 4x 8 bit access for one 32 bit buffer if the card
is not fully powered on yet - or if it's fully powered on then 1x 32
bit access is used)
- checking whether there's space in the TX FIFO queue to transmit data
- transfers from the host to the device for actual network traffic,
reserved pages (for firmware download) and H2C (host-to-card)
transfers
- receiving data from the device
- deep power saving state
The transmit path is optimized so DMA-capable SDIO host controllers can
directly use the buffers provided because the buffer's physical
addresses are 8 byte aligned.
The receive path is prepared to support RX aggregation where the
chipset combines multiple MAC frames into one bigger buffer to reduce
SDIO transfer overhead.
Co-developed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-3-martin.blumenstingl@googlemail.com
The SDIO HCI implementation needs to know when the MAC is powered on.
This is needed because 32-bit register access has to be split into 4x
8-bit register access when the MAC is not fully powered on or while
powering off. When the MAC is powered on 32-bit register access can be
used to reduce the number of transfers but splitting into 4x 8-bit
register access still works in that case.
During the power on sequence is how RTW_FLAG_POWERON is only set when
the power on sequence has completed successfully. During power off
however RTW_FLAG_POWERON is set. This means that the upcoming SDIO HCI
implementation does not know that it has to use 4x 8-bit register
accessors. Clear the RTW_FLAG_POWERON flag early when powering off the
MAC so the whole power off sequence is processed with RTW_FLAG_POWERON
unset. This will make it possible to use the RTW_FLAG_POWERON flag in
the upcoming SDIO HCI implementation.
Note that a failure in rtw_pwr_seq_parser() while applying
chip->pwr_off_seq can theoretically result in the RTW_FLAG_POWERON
flag being cleared while the chip is still powered on. However,
depending on when the failure occurs in the power off sequence the
chip may be on or off. Even the original approach of clearing
RTW_FLAG_POWERON only when the power off sequence has been applied
successfully could end up in some corner case where the chip is
powered off but RTW_FLAG_POWERON was not cleared.
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-2-martin.blumenstingl@googlemail.com
This patch adds support for platform-specific reset logic in the
stmmac driver. Some SoCs require a different reset mechanism than
the standard dwmac IP reset. To support these platforms, a new function
pointer 'fix_soc_reset' is added to the plat_stmmacenet_data structure.
The stmmac_reset in hwif.h is modified to call the 'fix_soc_reset'
function if it exists. This enables the driver to use the platform-specific
reset logic when necessary.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230403222302.328262-1-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the sake of readability, use the netlink payload helpers from
the 'nla_get_*()' family to parse the attributes.
tdc results:
1..5
ok 1 9903 - Add mqprio Qdisc to multi-queue device (8 queues)
ok 2 453a - Delete nonexistent mqprio Qdisc
ok 3 5292 - Delete mqprio Qdisc twice
ok 4 45a9 - Add mqprio Qdisc to single-queue device
ok 5 2ba9 - Show mqprio class
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230404203449.1627033-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kalle Valo says:
====================
wireless-next patches for v6.3
Smaller pull request this time, sending this early to fix the conflict
in mac80211. Nothing really special this time, only smaller changes.
* enable Wi-Fi 7 (EHT) mesh support
* tag 'wireless-next-2023-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (37 commits)
wifi: rt2x00: Fix memory leak when handling surveys
wifi: b43legacy: Remove the unused function prev_slot()
wifi: rtw89: Remove redundant pci_clear_master
wifi: rtw89: fix potential race condition between napi_init and napi_enable
wifi: rtw89: config EDCCA threshold during scan to prevent TX failed
wifi: rtw89: fix incorrect channel info during scan due to ppdu_sts filtering
wifi: rtw89: remove superfluous H2C of join_info
wifi: rtw89: set data lowest rate according to AP supported rate
wifi: rtw89: add counters of register-based H2C/C2H
wifi: rtw89: coex: Update Wi-Fi Bluetooth coexistence version to 7.0.1
wifi: rtw89: coex: Add report control v5 variation
wifi: rtw89: coex: Update RTL8852B LNA2 hardware parameter
wifi: rtw89: coex: Not to enable firmware report when WiFi is power saving
wifi: rtw89: coex: Add LPS protocol radio state for RTL8852B
bcma: remove unused mips_read32 function
bcma: Use of_address_to_resource()
wifi: mwifiex: remove unused evt_buf variable
wifi: brcmsmac: ampdu: remove unused suc_mpdu variable
wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_reg()
wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_rfreg()
...
====================
Link: https://lore.kernel.org/r/20230405111037.4792BC43443@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-04-04-2
The first patch is by Oliver Hartkopp and makes the maximum pdu size
of the CAN ISOTP protocol configurable.
The following 5 patches are by Dario Binacchi and add support for the
bxCAN controller by ST.
Geert Uytterhoeven's patch for the rcar_canfd driver fixes a sparse
warning.
Peng Fan's patch adds an optional power-domains property to the
flexcan device tree binding.
Frank Jungclaus adds support for CAN_CTRLMODE_BERR_REPORTING to the
esd_usb driver.
The last patch is by Oliver Hartkopp and converts the USB IDs of the
kvaser_usb driver to hexadecimal values.
* tag 'linux-can-next-for-6.4-20230404-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
kvaser_usb: convert USB IDs to hexadecimal values
can: esd_usb: Add support for CAN_CTRLMODE_BERR_REPORTING
dt-bindings: can: fsl,flexcan: add optional power-domains property
can: rcar_canfd: rcar_canfd_probe(): fix plain integer in transceivers[] init
can: bxcan: add support for ST bxCAN controller
ARM: dts: stm32: add pin map for CAN controller on stm32f4
ARM: dts: stm32: add CAN support on stm32f429
dt-bindings: net: can: add STM32 bxcan DT bindings
dt-bindings: arm: stm32: add compatible for syscon gcan node
can: isotp: add module parameter for maximum pdu size
====================
Link: https://lore.kernel.org/r/20230404145908.1714400-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The arguments passed to the trace events are of type unsigned int,
however the signature of the events used __le32 parameters.
I may be missing the point here, but sparse flagged this and it
does seem incorrect to me.
net/qrtr/ns.c: note: in included file (through include/trace/trace_events.h, include/trace/define_trace.h, include/trace/events/qrtr.h):
./include/trace/events/qrtr.h:11:1: warning: cast to restricted __le32
./include/trace/events/qrtr.h:11:1: warning: restricted __le32 degrades to integer
./include/trace/events/qrtr.h:11:1: warning: restricted __le32 degrades to integer
... (a lot more similar warnings)
net/qrtr/ns.c:115:47: expected restricted __le32 [usertype] service
net/qrtr/ns.c:115:47: got unsigned int service
net/qrtr/ns.c:115:61: warning: incorrect type in argument 2 (different base types)
... (a lot more similar warnings)
Fixes: dfddb54043 ("net: qrtr: Add tracepoint support")
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230402-qrtr-trace-types-v1-1-92ad55008dd3@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Announce that the driver supports CAN_CTRLMODE_BERR_REPORTING by means
of priv->can.ctrlmode_supported. Until now berr reporting always has
been active without taking care of the berr-reporting parameter given
to an "ip link set ..." command.
Additionally apply some changes to function esd_usb_rx_event():
- If berr reporting is off and it is also no state change, then
immediately return.
- Unconditionally (even in case of the above "immediate return") store
tx- and rx-error counters, so directly use priv->bec.txerr and
priv->bec.rxerr instead of intermediate variables.
- Not directly related, but to better point out the linkage between a
failed alloc_can_err_skb() and stats->rx_dropped++:
Move the increment of the rx_dropped statistic counter (back) to
directly behind the err_skb allocation.
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20230330184446.2802135-1-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This updates expected return values for invalid buffer test. Now such
values are returned from transport, not from af_vsock.c.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This removes behaviour, where error code returned from any transport
was always switched to ENOMEM. This works in the same way as:
commit
c43170b7e1 ("vsock: return errors other than -ENOMEM to socket"),
but for receive calls.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds conversion of VMCI specific error code to general -ENOMEM. It
is preparation for the next patch, which changes af_vsock.c behaviour
on receive to pass value returned from transport to the user.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
