Be consistent in whether we flag a full modeset or a
fastset for the pipe. intel_modeset_all_pipes() would
seem to be the only codepath not getting this right.
The other case is when we flag the fastset initially,
currently we just clear the mode_changed flag and set
the update_pipe flag. But we could still have
connectors_changed==true or active_changed==true forcing
a full modeset anyway. So check for that after clearing
the mode_changed flag.
And let's add a WARN to make sure we did get it right.
v2: Deal with {connectors,active}_changed
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221021162442.27283-4-ville.syrjala@linux.intel.com
On BDW+ we have just the one set of DP M/N registers. The
values we write into said registers depends on whether we
want DRRS to be in high or low gear. This causes issues
for the state checker which currently has to assume either
set of M/N (high or low refresh rate) values may appear there.
That sort of works for M/N itself, but all other values
derived from the M/N (dotclock, pixel rate) are not handled
correctly, leading to potential for state checker mismatches.
Let's avoid all those problems by simply keeping DRRS in
high gear until the state checker has done its hardware
state readout.
Note that hitting this issue presumable became very hard
after commit 1b333c679a ("drm/i915: Do DRRS disable/enable
during pre/post_plane_update()") since the state check would
have to laze about for one full second (delay used by
intel_drrs_schedule_work()) to see the low refresh rate.
But it is still theoretically possible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020120706.25728-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DGFX platforms has lmem and cpu can access the lmem objects
via mmap and i915 internal i915_gem_object_pin_map() for
i915 own usages. Both of these methods has pre-requisite
requirement to keep GFX PCI endpoint in D0 for a supported
iomem transaction over PCI link. (Refer PCIe specs 5.3.1.4.1)
Both DG1/DG2 have a known hardware bug that violates the PCIe specs
and support the iomem read write transaction over PCIe bus despite
endpoint is D3 state.
Due to above H/W bug, we had never observed any issue with i915 runtime
PM versus lmem access.
But this issue becomes visible when PCIe gfx endpoint's upstream
bridge enters to D3, at this point any lmem read/write access will be
returned as unsupported request. But again this issue is not observed
on every platform because it has been observed on few host machines
DG1/DG2 endpoint's upstream bridge does not bind with pcieport driver.
which really disables the PCIe power savings and leaves the bridge
at D0 state.
We need a unique interface to read/write from lmem with runtime PM
wakeref protection something similar to intel_uncore_{read, write},
keep autosuspend control to 'on' on all discrete platforms,
until we have a unique interface to read/write from lmem.
This just change the default autosuspend setting of i915 on dGPU,
user can still change it to 'auto'.
v2:
- Modified the commit message and subject with more information.
- Changed the Fixes tag to LMEM support commit. [Joonas]
- Changed !HAS_LMEM() Cond to !IS_DGFX(). [Rodrigo]
Fixes: b908be543e ("drm/i915: support creating LMEM objects")
Suggested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014113258.1284226-1-anshuman.gupta@intel.com
MTL and dgfx use the same DC5 counter.
While at it, this patch also adds the corresponding
debugfs entries. Some cleanup wrt dc3co register
which makes the code more readable.
Driver loads all firmware that it finds in the firmware
binary but platform doesn't *need* all of them. Cleaning the
previous debugs entries to reflect which firmware is needed
and if the needed firmware is loaded or not.
MTL needs both Pipe A and Pipe B DMC to be loaded
along with Main DMC.
BSpec: 49788
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221010202135.28388-1-anusha.srivatsa@intel.com
Currently we do the DRIVER_ATOMIC disable as almost the
first thing during pci probe. That involves the use of
DISPLAY_VER() which is perhaps a bit sketchy now that we
may need to read that out from the hardware itself.
Looks like we do populate a default value for it anyway
so the current does at least still work.
But let's make this safer anyway and move the code
into intel_device_info_runtime_init() where we also
handle the same thing for the !HAS_DISPLAY case.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221007211108.3883-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We've excluded gmch platforms from writing the final watermarks
for any disabled pipe. IIRC the reason was perhaps some lingering
issue with the watermark merging across the pipes. But I can't
really see any reason for this anymore, so let's unify this behaviour.
The main benefit being more consistency in register dumps when
we don't have stale watermarks hanging around in the registers.
Functionally there should be no difference as the hardware just
ignore all of it when the pipe is disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155452.32587-9-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
On g4x/vlv/chv the hardware seems incapable of changing the pixel
format, rotation, or YUV->RGB CSC matrix while in CxSR.
Additionally on VLV/CHV the sprites seem incapable of tiling
changes while in CxSR. On g4x CxSR is not even possible with
the sprite enabled. Curiously the primary plane seems perfectly
happy when changing tiling during CxSR.
Pimp up the code to account for these when determining whether
CxSR needs to be disabled. Since it looks like most of the plane
control register bits are affected let's just compare that.
But in the name of efficiency we'll make an exception for the
primary plane tiling changes (avoids some extra vblank waits).
v2: Just use the pre-computed plane control register values
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155452.32587-7-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Make sure modes with crazy big dotclocks are rejected early,
so as to not cause problems for subsequent code via integer
overflows and whatnot.
These would eventually be rejected in intel_crtc_compute_pipe_mode()
but that is now too late as we do the clock computations a bit
earlier than that. And we don't want to just reorder the two since
we still want to check the final computed dotclock against the
hardware limit to make sure we didn't end up above the limit due
to rounding/etc.
Fixes: 0ff0e219d9 ("drm/i915: Compute clocks earlier")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927182455.3422-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Current PSR code is supposed to use TRANSCODER_EDP to force 0 shift for
bits in PSR_IMR/IIR registers:
/*
* gen12+ has registers relative to transcoder and one per transcoder
* using the same bit definition: handle it as TRANSCODER_EDP to force
* 0 shift in bit definition
*/
At the time of writing the code assumption "TRANSCODER_EDP == 0" was made.
This is not the case and all fields in PSR_IMR and PSR_IIR are shifted
incorrectly if DISPLAY_VER >= 12.
Fix this by adding separate register field defines for >=12 and add bit
getter functions to keep code readability.
v4:
- Remove EDP from TGL definitions (José)
- Use REG_BIT and REG_GENMASK (José)
v3:
- Add separate register field defines (José)
- Add bit getter functions (José)
v2:
- Improve commit message (José)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: 8241cfbe67 ("drm/i915/tgl: Access the right register when handling PSR interruptions")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003072011.72408-1-jouni.hogander@intel.com
.load_luts() potentially runs from the vblank worker, and is
under a deadline to complete within the vblank. Thus we can't
do expesive stuff like talk to the Punit, etc.
To that end get rid of the assert_dsi_pll_enabled() call for
vlv/chv. We'll just have to trust that the PLL is already enabled
here.
And I don't think the normal assert_pll_enabled() really buys us
anything useful on gmch platforms either, so nuke that one too.
We don't have corresponding asserts in the ilk+ codepaths anyway
despite the hardware (IIRC) still requiring the clock to be
enabled when we access the LUT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929071521.26612-2-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
