This patch adds SMP support for MStar/Sigmastar chips that have a second core
like those in the infinity2m family.
So far only single and dual core chips have been found so this does
the bare minimum to boot the second core. From what I can tell not having
the "holding pen" code to handle multiple cores is fine if there is only
one core the will get booted. This might need to be reconsidered if chips
with more cores turn up.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201201134330.3037007-11-daniel@0x0f.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The infinity2m series of chips are like the other Mstar/Sigmastar
chips in that they have a Cortex A7 system with DDR memory integrated
in a single package.
The infinity2m chips are intended for recording the incoming streams
from IP cameras. So instead of video encoders they have video decoders,
instead of a camera interface they have display hardware and so on.
Aside from the above points the big difference about these chips is that
they include a second Cortex A7 core.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201201134330.3037007-5-daniel@0x0f.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v5.11, part three
1. S3C bindings and DTS cleanup,
2. Correct the clock rates for SPI0 in Artik 5 which is a fix for recently
introduced Ethernet on SPI on Artik 5 board.
* tag 'samsung-dt-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Reduce assigned-clocks entries for SPI0 on Artik5 board
ARM: dts: s3c6410: correct SMDK6410 board compatible
ARM: dts: s3c24xx: add SMDK2416 board compatible
dt-bindings: arm: samsung: document S3C6410-based boards binding
dt-bindings: arm: samsung: document SMDK2416 board binding
Link: https://lore.kernel.org/r/20201207074528.4475-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Veyron backlight fix, another fix for dtbs-check and some additions
to the rk3288-based VMARC boards.
* tag 'v5.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add SDIO0 node for VMARC SOM
ARM: dts: rockchip: Add rtc node for VMARC SOM
ARM: dts: rockchip: rename wdt nodename to watchdog on rv1108
ARM: dts: rockchip: Remove 0 point from brightness-levels on rk3288-veyron
Link: https://lore.kernel.org/r/4582475.GXAFRqVoOG@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Newly added boards are the PX30 SOM system from Engicam and Kobol Helios64.
The Scarlet tablet finally gets support for its cameras, now that the
the rk3399-isp moved out of staging.
The Odroid-Go-Advance got its joystick support now that the adc-joystick
driver was merged and misc omprovements to the RockPi4, rk3328-roc-cc
and orange-pi.
* tag 'v5.11-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (28 commits)
arm64: dts: rockchip: use USB host by default on rk3399-rock-pi-4
arm64: dts: rockchip: fix I2S conflict on rk3399-rock-pi-4
arm64: dts: rockchip: fix supplies on rk3399-rock-pi-4
arm64: dts: rockchip: Fix UART pull-ups on rk3328
arm64: dts: rockchip: add isp and sensors for Scarlet
arm64: dts: rockchip: add isp0 node for rk3399
arm64: dts: rockchip: Properly define the type C connector on rk3399-orangepi
arm64: dts: rockchip: Add BT support on px30-engicam
arm64: dts: rockchip: Add WiFi support on px30-engicam
arm64: dts: rockchip: Add Engicam PX30.Core C.TOUCH 2.0 10.1" OF
dt-bindings: arm: rockchip: Add Engicam PX30.Core C.TOUCH 2.0 10.1" OF
arm64: dts: rockchip: Enable LVDS panel on px30-engicam-edimm2.2
arm64: dts: rockchip: Enable USB Host, OTG on px30-enagicam
arm64: dts: rockchip: rename sdhci nodename to mmc on rk3399
arm64: dts: rockchip: Enable analog audio on rk3328-roc-cc
arm64: dts: rockchip: Enable HDMI audio on rk3328-roc-cc
arm64: dts: rockchip: Set dr_mode to "host" for OTG on rk3328-roc-cc
arm64: dts: rockchip: Add Engicam PX30.Core C.TOUCH 2.0
arm64: dts: rockchip: Add Engicam C.TOUCH 2.0
dt-bindings: arm: rockchip: Add Engicam PX30.Core C.TOUCH 2.0
...
Link: https://lore.kernel.org/r/4278011.LvFx2qVVIh@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX arm64 device tree changes for 5.11:
- New board support: LX2162A QDS, Kontron i.MX8M Mini SoMs and
baseboards.
- A number of patches from Adam Ford to add various audio devices for
i.MX8MM/MN and update imx8mm-beacon-som board on QSPI NOR and RTC.
- Correct WDOG_B pin configuration for i.MX8MM/MN/MP.
- A series from Ioana Ciornei complete the MAC/PCS/PHY representation
on DPAA2 devices.
- Add PMU device for i.MX8MP/MN.
- Add IR and CAN support for i.MX8MP/MN/MM EVK board.
- Adjust GIC CPU mask to match number of CPUs for i.MX8MP/MN/MM.
- A series of patch from Michael Walle to update LS1028A support with
addition of CAN and OPTEE, also ENETC PTP and FlexSPI clock input
correction.
- Add SPDIF sound card support on imx8mq-evk board.
- Misc random updates and device additions.
* tag 'imx-dt64-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
arm64: dts: imx8mm-beacon-som: Assign PMIC clock
arm64: dts: imx8mm-beacon-som: Configure RTC aliases
arm64: dts: imx8mn: Add node for SPDIF
arm64: dts: imx8mn: Add support for micfil
arm64: dts: imx8mn: Add SAI nodes
arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter
arm64: dts: ls1028a: make the eMMC and SD card controllers use fixed indices
arm64: dts: freescale: update calibration table for TMU module
arm64: dts: freescale: sl28: combine SPI MTD partitions
arm64: dts: ls1028a: add optee node
arm64: dts: ls1028a: fix FlexSPI clock input
arm64: dts: ls1028a: fix ENETC PTP clock input
arm64: dts: imx: Fix imx8mm-kontron-n801x-s.dtb target
arm64: dts: imx8mn-evk: add IR support
arm64: dts: imx8mm-evk: add IR support
arm64: dts: imx8mq-evk: add linux,autosuspend-period property for IR
arm64: dts: imx8mp-evk: add CAN support
arm64: dts: imx8mq-evk: Add spdif sound card support
arm64: dts: imx8mq: Configure clock rate for audio plls
arm64: dts: layerscape: Add PCIe EP node for ls1088a
...
Link: https://lore.kernel.org/r/20201202142717.9262-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree update for 5.11:
- New board support: imx6dl-alti6p, imx6dl-lanmcu, mx6qp-prtwd3,
imx6ul-phytec-segin and imx7d-flex-concentrator.
- Fix schema warnings for pwm-leds, watchdog and GPIO hog devices.
- A few patches from Krzysztof Kozlowski to correct compatibles for
i.MX6/7 boards.
- A series from Matthias Schiffer to polish imx7-mba7 board support.
- Update i.MX6/7 device trees for fsl,stop-mode support.
- Correct fsl,rcpm-wakeup of LS1021A to get flextimer wake-up work.
- A series of patch from Stefan Riedmueller to update phytec and segin
devices.
- Other small and random changes.
* tag 'imx-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (40 commits)
ARM: dts: imx28: Fix label name for L2 switch
ARM: dts: add Protonic WD3 board
ARM: dts: imx6qdl-kontron-samx6i: increase i2c-frequency
ARM: dts: imx7: add support for kamstrup flex concentrator
ARM: dts: ls1021a: update calibration table for TMU module
ARM: dts: ls1021a: fix rcpm failed to claim resource
ARM: dts: ls1021a: fix flextimer failed to wake system
ARM: dts: imx50-kobo-aura: Enable eKTF2132 touchscreen
ARM: dts: imx: Change flexcan node name to "can"
ARM: dts: imx6q-pico: fix board compatibles
ARM: dts: add Van der Laan LANMCU board
ARM: dts: add Altesco I6P board
ARM: dts: imx6ul: segin: peb-av-02: Mark stmpe touch as wakeup-source
ARM: dts: imx6ul: phytec: Add support for optional PEB-AV-02 LCD adapter
ARM: dts: imx6ul: segin: Add phyBOARD-Segin with eMMC phyCORE-i.MX6UL
ARM: dts: imx50-kobo-aura: Add 'grp' suffix to pinctrl node names
ARM: dts: imx: add usb alias
ARM: dts: imx6/7: sync fsl,stop-mode with current flexcan driver
ARM: dts: imx: Fix schema warnings for pwm-leds
ARM: dts: imx7s-warp: correct vendor in compatible to Element14
...
Link: https://lore.kernel.org/r/20201202142717.9262-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM64 changes for v5.11
1. Several cleanups, including aligning node names with dtschema.
2. Add WiFi/PCIe to TM2 boards (Exynos5433).
3. Correct restart and shutdown of Exynos7 boards, as part of Paweł
Chmiel Exynos7420 mainlining effort.
* tag 'samsung-dt64-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Drop incorrect use of io-channel-ranges property
arm64: dts: exynos: use hyphens in Exynos5433 node names
arm64: dts: exynos: Correct psci compatible used on Exynos7
arm64: dts: exynos: Include common syscon restart/poweroff for Exynos7
arm64: dts: exynos: add the WiFi/PCIe support to TM2(e) boards
arm64: dts: exynos: remove redundant status=okay in Exynos5433 TM2
arm64: dts: exynos: adjust node names to DT spec in Exynos7 Espresso
arm64: dts: exynos: adjust node names to DT spec in Exynos5433 TM2
arm64: dts: exynos: Harmonize DWC USB3 DT nodes name
Link: https://lore.kernel.org/r/20201201204404.22675-3-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v5.11, part two
1. Add devicetree of Samsung Galaxy Note 10.1 tablets
(GT-N8010/GT-N8013), called P4 Note. These are quite old but
still functional devices, based on Exynos4412.
2. Minor cleanups in Odroid XU3 Ethernet.
3. Minor fixes: ADC io-channel-ranges and P4 Note touchscreen GPIO
polarity.
* tag 'samsung-dt-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: switch Atmel mxt reset GPIO to active low on P4 Note
ARM: dts: s5pv210: Drop unneeded io-channel-ranges property in Aries
ARM: dts: s5pv210: Drop incorrect use of io-channel-ranges property
ARM: dts: exynos: Drop incorrect use of io-channel-ranges
ARM: dts: exynos: add Samsung's Exynos4412-based P4 Note boards
dt-bindings: arm: samsung: document bindings for P4 Note family board
ARM: dts: exynos: Add an alias for the Ethernet interface on Odroid XU3
ARM: dts: exynos: Fix Ethernet interface description on Odroid XU3
Link: https://lore.kernel.org/r/20201201204404.22675-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm DT updates for 5.11
This adds support for SD card, WiFi, LED, touchscreeni, touchkey and
fuel gauge to the Samsung Galaxy S5. Nexus 5 also gains fuel gauge
support.
Finally IPQ6016 gains support for the QPIC NAND controller.
* tag 'qcom-dts-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: ipq6018: Add the QPIC peripheral nodes
ARM: dts: qcom-pma8084: Drop incorrect use of io-channel-ranges
ARM: dts: qcom: msm8974-lge-nexus5: Add fuel gauge
ARM: dts: qcom: msm8974-klte: Add fuel gauge
ARM: dts: qcom: msm8974-klte: Add support for SD card
ARM: dts: qcom: msm8974-klte: Add support for wifi
ARM: dts: qcom: msm8974-klte: Add gpio expander chip
ARM: dts: qcom: msm8974-klte: Add support for led
ARM: dts: qcom: msm8974-klte: Add support for touchscreen
ARM: dts: qcom: msm8974-klte: Add support for touchkey
ARM: dts: qcom: msm8974-klte: Merge pinctrl nodes
Link: https://lore.kernel.org/r/20201130190148.345302-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 DT updates for 5.11
For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.
Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.
MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.
MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.
MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.
SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.
SC7180 gains a slew of smaller improvements and fixes.
* tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (93 commits)
arm64: dts: qcom: c630: Define eDP bridge and panel
arm64: dts: qcom: c630: Fix pinctrl pins properties
arm64: dts: qcom: c630: Polish i2c-hid devices
arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
arm64: dts: sdm845: Add interconnect properties for QUP
interconnect: qcom: sdm845: Add the missing nodes for QUP
dt-bindings: interconnect: sdm845: Add IDs for the QUP ports
arm64: dts: qcom: c630: Expose LID events
arm64: dts: qcom: c630: Re-enable apps_smmu
dts: qcom: sdm845: Add dt entries to support crypto engine.
arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD
arm64: dts: qcom: sdm845: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: limit IPA iommu streams
arm64: dts: qcom: sm8150: Add Coresight support
arm64: dts: qcom: sc7180-trogdor: Make pp3300_a the default supply for pp3300_hub
arm64: dts: qcom: sc7180: Add DDR/L3 votes for the pro variant
arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite
arm64: dts: qcom: sc7180-trogdor: add "pen-insert" label for trogdor
arm64: qcom: sc7180: trogdor: Add ADC nodes and thermal zone for charger thermistor
...
Link: https://lore.kernel.org/r/20201130190131.345187-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt64 for 5.11 (part 1)
- Add support for IEI Puzzle-M801 board (Armada 8040 based)
- Add support ESPRESSObin-Ultra (Armada 3720 based)
- Clean-up and improve espressobin device tree
- Switch to per-port SATA interrupts on CP110 based SoC
- Use compliant node name for USB3 on CP110 based SoC
- Add heartbeat LED on mcbin singleshot
- Disable SMMU by default for Armada 7040 and 8040 to continued
supporting custom bot firmware
- Turris mox:
- add 3W power capability to SFP cage
- update ethernet-phy handle name
* tag 'mvebu-dt64-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada-3720-turris-mox: add 3W power capability to SFP cage
arm64: dts: marvell: keep SMMU disabled by default for Armada 7040 and 8040
arm64: dts: mcbin-singleshot: add heartbeat LED
arm64: dts: marvell: cp11x: Harmonize xHCI DT nodes name
arm64: dts: marvell: espressobin: Update link to V7 schematic
arm64: dts: armada-3720-turris-mox: update ethernet-phy handle name
arm64: dts: marvell: armada-cp110: Switch to per-port SATA interrupts
arm64: dts: marvell: add DT for ESPRESSObin-Ultra
arm64: dts: marvell: espressobin: Add support for LED2
arm64: dts: marvell: Add a device tree for the IEI Puzzle-M801 board
arm64: dts: marvell: espressobin: De-duplicate eMMC definitions
arm64: dts: marvell: espressobin: Get rid of duplicate serial aliases
arm64: dts: marvell: espressobin: Simplify v7 ethernet port labeling
Link: https://lore.kernel.org/r/87eekaj0i4.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.11, please pull the following:
- Rafal adds initial support for the Broadcom 4908 which are SoCs used
in home routers and are based on the DSL architecture and using
Broadcom Brahma-B53 CPUs.
* tag 'arm-soc/for-5.11/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: add config for Broadcom BCM4908 SoCs
arm64: dts: broadcom: add BCM4908 and Asus GT-AC5300 early DTS files
dt-bindings: arm: bcm: document BCM4908 bindings
Link: https://lore.kernel.org/r/20201128163410.1691529-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs changes for 5.11,
please pull the following:
- Vivek updates the Linksys EA9500 DTS by adding the two additional
switch port nodes (5 & 7), providing a flash partition layout to
make the device usable with OpenWrt, and finally switches to using
the pin controller rather than using mdio-mux to get the same outcome.
- Serge fixes the USB Device Tree nodes unit name to be conformant to
the recommended name patterns.
- Rafal re-arranges all the nodes that belonged to the CRU block to be
under the CRU node (such as PLLs). He also disables the USB3 PHY node
for devices that lack USB3 and adds USB3 support to the Luxul XWR-3150
DTS.
- Jonathan drops the incorrect 'io-channel-ranges' from the Cygnus SoC
DTSI.
- Maxime disables the Wi-Fi frequencies (around 2.4GHz) for HDMI on the
Raspberry Pi 4 due to some cross-talk between the two blocks.
- Pavel updates the DWC2 USB controller RX FIFO sizes to be more
accurate for all BCM283x (Raspberr Pi) SoCs.
- Florian updates all BCM5301x and NSP Device Tree files to allow
switching the Broadcom B53 Ethernet switch device tree binding to YAML.
* tag 'arm-soc/for-5.11/devicetree' of https://github.com/Broadcom/stblinux: (22 commits)
dt-bindings: net: dsa: b53: Add YAML bindings
ARM: dts: NSP: Provide defaults ports container node
ARM: dts: NSP: Add a SRAB compatible string for each board
ARM: dts: NSP: Fix Ethernet switch SGMII register name
ARM: dts: NSP: Update ethernet switch node name
ARM: dts: BCM5301X: Provide defaults ports container node
ARM: dts: BCM5301X: Add a default compatible for switch node
ARM: dts: BCM5301X: Update Ethernet switch node name
dt-bindings: net: dsa: Document sfp and managed properties
dt-bindings: net: dsa: Extend switch nodes pattern
ARM: dts: bcm283x: increase dwc2's RX FIFO size
ARM: dts: rpi-4: disable wifi frequencies
ARM: dts: Cygnus: Drop incorrect io-channel-ranges property.
ARM: dts: BCM5301X: Enable USB 3 PHY on Luxul XWR-3150
ARM: dts: BCM5301X: Disable USB 3 PHY on devices without USB 3
ARM: dts: BCM5301X: Move CRU devices to the CRU node
ARM: dts: BCM5301X: Linksys EA9500 make use of pinctrl
ARM: dts: BCM5301X: Use corretc pinctrl compatible for 4709x
ARM: dts: BCM5301X: Linksys EA9500 add fixed partitions
ARM: dts: BCM5310X: Harmonize xHCI DT nodes name
...
Link: https://lore.kernel.org/r/20201128163410.1691529-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GT-King and GT-King-Pro boxes have an RTC chip and power cell, so enable it.
GTKING:~ # dmesg | grep rtc
[ 5.237245] meson-vrtc ff8000a8.rtc: registered as rtc1
[ 5.261869] rtc-hym8563 0-0051: registered as rtc0
[ 5.265016] rtc-hym8563 0-0051: setting system clock to 2020-11-30T09:16:54 UTC (1606727814)
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201201062135.18241-1-christianshewitt@gmail.com
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240 ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue where the Ethernet link doesn't come up
when using ip link set down/up:
[ 29.360965] meson8b-dwmac ff3f0000.ethernet eth0: Link is Down
[ 34.569012] meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=31)
[ 34.676732] meson8b-dwmac ff3f0000.ethernet: Failed to reset the dma
[ 34.678874] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 34.687850] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: 658e4129bb ("arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY reset line")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/df3f5c4fc6e43c55429fd3662a636036a21eed49.1607363522.git.stefan@agner.ch
