Since we are about to remove the lower limit on the IPA size,
make sure that we do not go to 1 level page table (e.g, with
32bit IPA on 64K host with concatenation) to avoid splitting
the host PMD huge pages at stage2.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far we have restricted the IPA size of the VM to the default
value (40bits). Now that we can manage the IPA size per VM and
support dynamic stage2 page tables, we can allow VMs to have
larger IPA. This patch introduces a the maximum IPA size
supported on the host. This is decided by the following factors :
1) Maximum PARange supported by the CPUs - This can be inferred
from the system wide safe value.
2) Maximum PA size supported by the host kernel (48 vs 52)
3) Number of levels in the host page table (as we base our
stage2 tables on the host table helpers).
Since the stage2 page table code is dependent on the stage1
page table, we always ensure that :
Number of Levels at Stage1 >= Number of Levels at Stage2
So we limit the IPA to make sure that the above condition
is satisfied. This will affect the following combinations
of VA_BITS and IPA for different page sizes.
Host configuration | Unsupported IPA ranges
39bit VA, 4K | [44, 48]
36bit VA, 16K | [41, 48]
42bit VA, 64K | [47, 52]
Supporting the above combinations need independent stage2
page table manipulation code, which would need substantial
changes. We could purse the solution independently and
switch the page table code once we have it ready.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for handling 52bit guest physical address to the
VGIC layer. So far we have limited the guest physical address
to 48bits, by explicitly masking the upper bits. This patch
removes the restriction. We do not have to check if the host
supports 52bit as the gpa is always validated during an access.
(e.g, kvm_{read/write}_guest, kvm_is_visible_gfn()).
Also, the ITS table save-restore is also not affected with
the enhancement. The DTE entries already store the bits[51:8]
of the ITT_addr (with a 256byte alignment).
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[ Macro clean ups, fix PROPBASER and PENDBASER accesses ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we can manage the stage2 page table per VM, switch the
configuration details to per VM instance. The VTCR is updated
with the values specific to the VM based on the configuration.
We store the IPA size and the number of stage2 page table levels
for the guest already in VTCR. Decode it back from the vtcr
field wherever we need it.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VTCR_EL2 holds the following key stage2 translation table
parameters:
SL0 - Entry level in the page table lookup.
T0SZ - Denotes the size of the memory addressed by the table.
We have been using fixed values for the SL0 depending on the
page size as we have a fixed IPA size. But since we are about
to make it dynamic, we need to calculate the SL0 at runtime
per VM. This patch adds a helper to compute the value of SL0
for a VM based on the IPA size.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On arm64 VTTBR_EL2:BADDR holds the base address for the stage2
translation table. The Arm ARM mandates that the bits BADDR[x-1:0]
should be 0, where 'x' is defined for a given IPA Size and the
number of levels for a translation granule size. It is defined
using some magical constants. This patch is a reverse engineered
implementation to calculate the 'x' at runtime for a given ipa and
number of page table levels. See patch for more details.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Switch to dynamic stage2 page table layout based on the given
VM. So far we had a common stage2 table layout determined at
compile time. Make decision based on the VM instance depending
on the IPA limit for the VM. Adds helpers to compute the stage2
parameters based on the guest's IPA and uses them to make the decisions.
The IPA limit is still fixed to 40bits and the build time check
to ensure the stage2 doesn't exceed the host kernels page table
levels is retained. Also make sure that we use the pud/pmd level
helpers from the host only when they are not folded.
Cc: Christoffer Dall <cdall@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Our stage2 page table helpers are statically defined based
on the fixed IPA of 40bits and the host page size. As we are
about to add support for configurable IPA size for VMs, we
need to make the page table checks for each VM. This patch
prepares the stage2 helpers to make the transition to a VM
dependent table layout easier. Instead of statically defining
the table helpers based on the page table levels, we now
check the page table levels in the helpers to do the right
thing. In effect, it simply converts the macros to static
inline functions.
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Right now the stage2 page table for a VM is hard coded, assuming
an IPA of 40bits. As we are about to add support for per VM IPA,
prepare the stage2 page table helpers to accept the kvm instance
to make the right decision for the VM. No functional changes.
Adds stage2_pgd_size(kvm) to replace S2_PGD_SIZE. Also, moves
some of the definitions in arm32 to align with the arm64.
Also drop the _AC() specifier constants wherever possible.
Cc: Christoffer Dall <cdall@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for setting the VTCR_EL2 per VM, rather than hard
coding a value at boot time per CPU. This would allow us to tune
the stage2 page table parameters per VM in the later changes.
We compute the VTCR fields based on the system wide sanitised
feature registers, except for the hardware management of Access
Flags (VTCR_EL2.HA). It is fine to run a system with a mix of
CPUs that may or may not update the page table Access Flags.
Since the bit is RES0 on CPUs that don't support it, the bit
should be ignored on them.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the new helper for converting the parange to the physical shift.
Also, add the missing definitions for the VTCR_EL2 register fields
and use them instead of hard coding numbers.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On arm64, ID_AA64MMFR0_EL1.PARange encodes the maximum Physical
Address range supported by the CPU. Add a helper to decode this
to actual physical shift. If we hit an unallocated value, return
the maximum range supported by the kernel.
This will be used by KVM to set the VTCR_EL2.T0SZ, as it
is about to move its place. Having this helper keeps the code
movement cleaner.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We load the stage2 context of a guest for different operations,
including running the guest and tlb maintenance on behalf of the
guest. As of now only the vttbr is private to the guest, but this
is about to change with IPA per VM. Add a helper to load the stage2
configuration for a VM, which could do the right thing with the
future changes.
Cc: Christoffer Dall <cdall@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far we have only supported 3 level page table with fixed IPA of
40bits, where PUD is folded. With 4 level page tables, we need
to check if the PUD entry is valid or not. Fix stage2_flush_memslot()
to do this check, before walking down the table.
Acked-by: Christoffer Dall <cdall@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Lee writes:
"MFD fixes for v4.19
- Fix Dialog DA9063 regulator constraints issue causing failure in
probe
- Fix OMAP Device Tree compatible strings to match DT"
* tag 'mfd-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: omap-usb-host: Fix dts probe of children
mfd: da9063: Fix DT probing with constraints
Juergen writes:
"xen:
Two small fixes for xen drivers."
* tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: issue warning message when out of grant maptrack entries
xen/x86/vpmu: Zero struct pt_regs before calling into sample handling code
Jens writes:
"Just a single fix in this pull request, fixing a regression in
/proc/diskstats caused by the unification of timestamps."
* tag 'for-linus-20180922' of git://git.kernel.dk/linux-block:
block: use nanosecond resolution for iostat
Thomas writes:
"A set of fixes for x86:
- Resolve the kvmclock regression on AMD systems with memory
encryption enabled. The rework of the kvmclock memory allocation
during early boot results in encrypted storage, which is not
shareable with the hypervisor. Create a new section for this data
which is mapped unencrypted and take care that the later
allocations for shared kvmclock memory is unencrypted as well.
- Fix the build regression in the paravirt code introduced by the
recent spectre v2 updates.
- Ensure that the initial static page tables cover the fixmap space
correctly so early console always works. This worked so far by
chance, but recent modifications to the fixmap layout can -
depending on kernel configuration - move the relevant entries to a
different place which is not covered by the initial static page
tables.
- Address the regressions and issues which got introduced with the
recent extensions to the Intel Recource Director Technology code.
- Update maintainer entries to document reality"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Expand static page table for fixmap space
MAINTAINERS: Add X86 MM entry
x86/intel_rdt: Add Reinette as co-maintainer for RDT
MAINTAINERS: Add Borislav to the x86 maintainers
x86/paravirt: Fix some warning messages
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Fix exclusive mode handling of MBA resource
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Do not allow pseudo-locking of MBA resource
x86/intel_rdt: Fix unchecked MSR access
x86/intel_rdt: Fix invalid mode warning when multiple resources are managed
x86/intel_rdt: Global closid helper to support future fixes
x86/intel_rdt: Fix size reporting of MBA resource
x86/intel_rdt: Fix data type in parsing callbacks
x86/kvm: Use __bss_decrypted attribute in shared variables
x86/mm: Add .bss..decrypted section to hold shared variables
Thomas writes:
"- Provide a strerror_r wrapper so lib/bpf can be built on systems
without _GNU_SOURCE
- Unbreak the man page generator when building out of tree"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf Documentation: Fix out-of-tree asciidoctor man page generation
tools lib bpf: Provide wrapper for strerror_r to build in !_GNU_SOURCE systems
Thomas writes:
"Make the EFI arm stub device tree loader default on to unbreak
existing EFI boot loaders which do not have DTB support."
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: default EFI_ARMSTUB_DTB_LOADER to y
Klaus Kusche reported that the I/O busy time in /proc/diskstats was not
updating properly on 4.18. This is because we started using ktime to
track elapsed time, and we convert nanoseconds to jiffies when we update
the partition counter. However, this gets rounded down, so any I/Os that
take less than a jiffy are not accounted for. Previously in this case,
the value of jiffies would sometimes increment while we were doing I/O,
so at least some I/Os were accounted for.
Let's convert the stats to use nanoseconds internally. We still report
milliseconds as before, now more accurately than ever. The value is
still truncated to 32 bits for backwards compatibility.
Fixes: 522a777566 ("block: consolidate struct request timestamp fields")
Cc: stable@vger.kernel.org
Reported-by: Klaus Kusche <klaus.kusche@computerix.info>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus writes:
"Pin control fixes for v4.19:
- Two fixes for the Intel pin controllers than cause
problems on laptops."
* tag 'pinctrl-v4.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: intel: Do pin translation in other GPIO operations as well
pinctrl: cannonlake: Fix gpio base for GPP-E
Paolo writes:
"It's mostly small bugfixes and cleanups, mostly around x86 nested
virtualization. One important change, not related to nested
virtualization, is that the ability for the guest kernel to trap
CPUID instructions (in Linux that's the ARCH_SET_CPUID arch_prctl) is
now masked by default. This is because the feature is detected
through an MSR; a very bad idea that Intel seems to like more and
more. Some applications choke if the other fields of that MSR are
not initialized as on real hardware, hence we have to disable the
whole MSR by default, as was the case before Linux 4.12."
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (23 commits)
KVM: nVMX: Fix bad cleanup on error of get/set nested state IOCTLs
kvm: selftests: Add platform_info_test
KVM: x86: Control guest reads of MSR_PLATFORM_INFO
KVM: x86: Turbo bits in MSR_PLATFORM_INFO
nVMX x86: Check VPID value on vmentry of L2 guests
nVMX x86: check posted-interrupt descriptor addresss on vmentry of L2
KVM: nVMX: Wake blocked vCPU in guest-mode if pending interrupt in virtual APICv
KVM: VMX: check nested state and CR4.VMXE against SMM
kvm: x86: make kvm_{load|put}_guest_fpu() static
x86/hyper-v: rename ipi_arg_{ex,non_ex} structures
KVM: VMX: use preemption timer to force immediate VMExit
KVM: VMX: modify preemption timer bit only when arming timer
KVM: VMX: immediately mark preemption timer expired only for zero value
KVM: SVM: Switch to bitmap_zalloc()
KVM/MMU: Fix comment in walk_shadow_page_lockless_end()
kvm: selftests: use -pthread instead of -lpthread
KVM: x86: don't reset root in kvm_mmu_setup()
kvm: mmu: Don't read PDPTEs when paging is not enabled
x86/kvm/lapic: always disable MMIO interface in x2APIC mode
KVM: s390: Make huge pages unavailable in ucontrol VMs
...
Richard writes:
"This pull request contains fixes for UBIFS:
- A wrong UBIFS assertion in mount code
- Fix for a NULL pointer deref in mount code
- Revert of a bad fix for xattrs"
* tag 'upstream-4.19-rc4' of git://git.infradead.org/linux-ubifs:
Revert "ubifs: xattr: Don't operate on deleted inodes"
ubifs: drop false positive assertion
ubifs: Check for name being NULL while mounting
Jens writes:
"Storage fixes for 4.19-rc5
- Fix for leaking kernel pointer in floppy ioctl (Andy Whitcroft)
- NVMe pull request from Christoph, and a single ANA log page fix
(Hannes)
- Regression fix for libata qd32 support, where we trigger an illegal
active command transition. This fixes a CD-ROM detection issue that
was reported, but could also trigger premature completion of the
internal tag (me)"
* tag 'for-linus-20180920' of git://git.kernel.dk/linux-block:
floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl
libata: mask swap internal and hardware tag
nvme: count all ANA groups for ANA Log page
David writes:
"drm fixes for 4.19-rc5:
- core: fix debugfs for atomic, fix the check for atomic for
non-modesetting drivers
- amdgpu: adds a new PCI id, some kfd fixes and a sdma fix
- i915: a bunch of GVT fixes.
- vc4: scaling fix
- vmwgfx: modesetting fixes and a old buffer eviction fix
- udl: framebuffer destruction fix
- sun4i: disable on R40 fix until next kernel
- pl111: NULL termination on table fix"
* tag 'drm-fixes-2018-09-21' of git://anongit.freedesktop.org/drm/drm: (21 commits)
drm/amdkfd: Fix ATS capablity was not reported correctly on some APUs
drm/amdkfd: Change the control stack MTYPE from UC to NC on GFX9
drm/amdgpu: Fix SDMA HQD destroy error on gfx_v7
drm/vmwgfx: Fix buffer object eviction
drm/vmwgfx: Don't impose STDU limits on framebuffer size
drm/vmwgfx: limit mode size for all display unit to texture_max
drm/vmwgfx: limit screen size to stdu_max during check_modeset
drm/vmwgfx: don't check for old_crtc_state enable status
drm/amdgpu: add new polaris pci id
drm: sun4i: drop second PLL from A64 HDMI PHY
drm: fix drm_drv_uses_atomic_modeset on non modesetting drivers.
drm/i915/gvt: clear ggtt entries when destroy vgpu
drm/i915/gvt: request srcu_read_lock before checking if one gfn is valid
drm/i915/gvt: Add GEN9_CLKGATE_DIS_4 to default BXT mmio handler
drm/i915/gvt: Init PHY related registers for BXT
drm/atomic: Use drm_drv_uses_atomic_modeset() for debugfs creation
drm/fb-helper: Remove set but not used variable 'connector_funcs'
drm: udl: Destroy framebuffer only if it was initialized
drm/sun4i: Remove R40 display pipeline compatibles
drm/pl111: Make sure of_device_id tables are NULL terminated
...
9092c71bb7 ("mm: use sc->priority for slab shrink targets") changed the
way that the target slab pressure is calculated and made it
priority-based:
delta = freeable >> priority;
delta *= 4;
do_div(delta, shrinker->seeks);
The problem is that on a default priority (which is 12) no pressure is
applied at all, if the number of potentially reclaimable objects is less
than 4096 (1<<12).
This causes the last objects on slab caches of no longer used cgroups to
(almost) never get reclaimed. It's obviously a waste of memory.
It can be especially painful, if these stale objects are holding a
reference to a dying cgroup. Slab LRU lists are reparented on memcg
offlining, but corresponding objects are still holding a reference to the
dying cgroup. If we don't scan these objects, the dying cgroup can't go
away. Most likely, the parent cgroup hasn't any directly charged objects,
only remaining objects from dying children cgroups. So it can easily hold
a reference to hundreds of dying cgroups.
If there are no big spikes in memory pressure, and new memory cgroups are
created and destroyed periodically, this causes the number of dying
cgroups grow steadily, causing a slow-ish and hard-to-detect memory
"leak". It's not a real leak, as the memory can be eventually reclaimed,
but it could not happen in a real life at all. I've seen hosts with a
steadily climbing number of dying cgroups, which doesn't show any signs of
a decline in months, despite the host is loaded with a production
workload.
It is an obvious waste of memory, and to prevent it, let's apply a minimal
pressure even on small shrinker lists. E.g. if there are freeable
objects, let's scan at least min(freeable, scan_batch) objects.
This fix significantly improves a chance of a dying cgroup to be
reclaimed, and together with some previous patches stops the steady growth
of the dying cgroups number on some of our hosts.
Link: http://lkml.kernel.org/r/20180905230759.12236-1-guro@fb.com
Fixes: 9092c71bb7 ("mm: use sc->priority for slab shrink targets")
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Rik van Riel <riel@surriel.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the clone and fork syscalls return EAGAIN when the limit on the
number of pids /proc/sys/kernel/pid_max is exceeded.
Currently, when the pid_max limit is exceeded, the kernel will return
ENOSPC from the fork and clone syscalls. This is contrary to the
documented behaviour, which explicitly calls out the pid_max case as one
where EAGAIN should be returned. It also leads to really confusing error
messages in userspace programs which will complain about a lack of disk
space when they fail to create processes/threads for this reason.
This error is being returned because alloc_pid() uses the idr api to find
a new pid; when there are none available, idr_alloc_cyclic() returns
-ENOSPC, and this is being propagated back to userspace.
This behaviour has been broken before, and was explicitly fixed in
commit 35f71bc0a0 ("fork: report pid reservation failure properly"),
so I think -EAGAIN is definitely the right thing to return in this case.
The current behaviour change dates from commit 95846ecf9d ("pid:
replace pid bitmap implementation with IDR AIP") and was I believe
unintentional.
This patch has no impact on the case where allocating a pid fails because
the child reaper for the namespace is dead; that case will still return
-ENOMEM.
Link: http://lkml.kernel.org/r/20180903111016.46461-1-ktsanaktsidis@zendesk.com
Fixes: 95846ecf9d ("pid: replace pid bitmap implementation with IDR AIP")
Signed-off-by: KJ Tsanaktsidis <ktsanaktsidis@zendesk.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Gargi Sharma <gs051095@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 11a6fc3dc7.
UBIFS wants to assert that xattr operations are only issued on files
with positive link count. The said patch made this operations return
-ENOENT for unlinked files such that the asserts will no longer trigger.
This was wrong since xattr operations are perfectly fine on unlinked
files.
Instead the assertions need to be fixed/removed.
Cc: <stable@vger.kernel.org>
Fixes: 11a6fc3dc7 ("ubifs: xattr: Don't operate on deleted inodes")
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Richard Weinberger <richard@nod.at>
The following sequence triggers
ubifs_assert(c, c->lst.taken_empty_lebs > 0);
at the end of ubifs_remount_fs():
mount -t ubifs /dev/ubi0_0 /mnt
echo 1 > /sys/kernel/debug/ubifs/ubi0_0/ro_error
umount /mnt
mount -t ubifs -o ro /dev/ubix_y /mnt
mount -o remount,ro /mnt
The resulting
UBIFS assert failed in ubifs_remount_fs at 1878 (pid 161)
is a false positive. In the case above c->lst.taken_empty_lebs has
never been changed from its initial zero value. This will only happen
when the deferred recovery is done.
Fix this by doing the assertion only when recovery has been done
already.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The requested device name can be NULL or an empty string.
Check for that and refuse to continue. UBIFS has to do this manually
since we cannot use mount_bdev(), which checks for this condition.
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Reported-by: syzbot+38bd0f7865e5c6379280@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
The handlers of IOCTLs in kvm_arch_vcpu_ioctl() are expected to set
their return value in "r" local var and break out of switch block
when they encounter some error.
This is because vcpu_load() is called before the switch block which
have a proper cleanup of vcpu_put() afterwards.
However, KVM_{GET,SET}_NESTED_STATE IOCTLs handlers just return
immediately on error without performing above mentioned cleanup.
Thus, change these handlers to behave as expected.
Fixes: 8fcc4b5923 ("kvm: nVMX: Introduce KVM_CAP_NESTED_STATE")
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Patrick Colp <patrick.colp@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because CRAT_CU_FLAGS_IOMMU_PRESENT was not set in some BIOS crat, we
need to workaround this.
For future compatibility, we also overwrite the bit in capability according
to the value of needs_iommu_device.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CWSR fails on Raven if the control stack is MTYPE_UC, which is used
for regular GART mappings. As a workaround we map it using MTYPE_NC.
The MEC firmware expects the control stack at one page offset from the
start of the MQD so it is part of the MQD allocation on GFXv9. AMDGPU
added a memory allocation flag just for this purpose.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <yong.zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some reason I thought GPIOLIB handles translation from GPIO ranges
to pinctrl pins but it turns out not to be the case. This means that
when GPIOs operations are performed for a pin controller having a custom
GPIO base such as Cannon Lake and Ice Lake incorrect pin number gets
used internally.
Fix this in the same way we did for lock/unlock IRQ operations and
translate the GPIO number to pin before using it.
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Reported-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
