Due to a workaround we have to make sure the WM1 watermarks block/lines
values are sensible even when WM1 is disabled. To that end we copy those
values from WM0.
However since we now keep each wm level enabled on a per-plane basis
it doesn't seem necessary to do that copy when we already have an
enabled WM1 on the current plane. That is, we might be in a situation
where another plane can only do WM0 (and thus needs the copy) but
the current plane's WM1 is still perfectly valid (ie. fits into the
current DDB allocation).
Skipping the copy could avoid reprogramming the plane's registers
needlessly in some cases.
Fixes: a301cb0fca ("drm/i915: Keep plane watermarks enabled more aggressively")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
There are cases, where devices have an HDMI1.4 retimer, and TMDS clock rate
is capped to 340MHz via VBT. In such cases scrambling might be supported
by the platform and an HDMI2.0 sink for lower TMDS rates, but not
supported by the retimer, causing blankouts.
So avoid enabling scrambling, if the TMDS clock is capped to <= 340MHz.
v2: Added comment, documenting the rationale to check for TMDS clock,
before going for scrambling. (Arun)
v3: Fixed the function name to check if source supports scrambling. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221222040851.3029514-1-ankit.k.nautiyal@intel.com
Current implementation of async flip w/a relies on assumption that
previous atomic commit contains valid information if async_flip is still
enabled on the plane. It is incorrect. If previous commit did not modify
the plane its state->uapi.async_flip can be false. As a result DMAR/PIPE
errors can be observed:
i915 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00000080
i915 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00000080
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [00:02.0] fault addr 0x0 [fault reason 0x06] PTE Read access is not set
v2: update async_flip_planes in more reliable places (Ville)
v3: reset async_flip_planes and do_async_flip in more scenarios (Ville)
v4: move all resets to plane loops (Ville)
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127153003.2225111-1-andrzej.hajda@intel.com
SEL_FETCH_CTL registers are armed immediately when plane is disabled.
SEL_FETCH_* instances of plane configuration are used when doing
selective update and normal plane register instances for full updates.
Currently all SEL_FETCH_* registers are written as a part of noarm
plane configuration. If noarm and arm plane configuration are not
happening within same vblank we may end up having plane as a part of
selective update before it's PLANE_SURF register is written.
Fix this by splitting plane selective fetch configuration into arm and
noarm versions and call them accordingly. Write SEL_FETCH_CTL in arm
version.
v3:
- add arm suffix into intel_psr2_disable_plane_sel_fetch
v2:
- drop color_plane parameter from arm part
- dev_priv -> i915 in arm part
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Vinod Govindapillai <vinod.govindapillai@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130080651.3796929-1-jouni.hogander@intel.com
During suspend flow, i915 currently achors' on the pm_suspend_prepare
callback as the location where we quiesce the entire GPU and perform
all necessary cleanup in order to go into suspend. PXP is also called
during this time to perform the arbitration session teardown (with
the assurance no additional GEM IOCTLs will come after that could
restart the session).
However, if other devices or drivers fail their suspend_prepare, the
system will not go into suspend and i915 will be expected to resume
operation. In this case, we need to re-initialize the PXP hardware
and this really should be done within the pm_resume_complete callback
which is the correct opposing function in the resume sequence to
match pm_suspend_prepare of the suspend sequence.
Because this callback is the last thing at the end of resuming
we expect little to no impact to the rest of the i915 resume sequence
with this change.
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-7-alan.previn.teres.alexis@intel.com
A driver bug was recently discovered where the security firmware was
receiving internal HW signals indicating that session key expirations
had occurred. Architecturally, the firmware was expecting a response
from the GuC to acknowledge the event with the firmware side.
However the OS was in a suspended state and GuC had been reset.
Internal specifications actually required the driver to ensure
that all active sessions be properly cleaned up in such cases where
the system is suspended and the GuC potentially unable to respond.
This patch adds the global teardown code in i915's suspend_prepare
code path.
v2 : Split __pxp_global_teardown_locked helper into two variants
for teardown-with-restart vs teardown-for-suspend/shutdown.
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Juston Li <justonli@chromium.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-6-alan.previn.teres.alexis@intel.com
A gap was recently discovered where if an application did not
invalidate all of the stream keys (intentionally or not), and the
driver did a full PXP global teardown on the GT subsystem, we
find that future session creation would fail on the security
firmware's side of the equation. i915 is the entity that needs
ensure the sessions' state across both iGT and security firmware
are at a known clean point when performing a full global teardown.
Architecturally speaking, i915 should inspect all active sessions
and submit the invalidate-stream-key PXP command to the security
firmware for each of them. However, for the upstream i915 driver
we only support the arbitration session that can be created
so that will be the only session we will cleanup.
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Juston Li <justonli@chromium.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-5-alan.previn.teres.alexis@intel.com
Avoid the array lookup, converting the PLL macros after ICL to
_PICK_EVEN_RANGES. This provides the following reduction in code size:
$ size build64/drivers/gpu/drm/i915/i915.o{.old,.new}
text data bss dec hex filename
4027456 185703 6984 4220143 4064ef build64/drivers/gpu/drm/i915/i915.o.old
4026997 185703 6984 4219684 406324 build64/drivers/gpu/drm/i915/i915.o.new
At the same time it's safer, avoiding out-of-bounds array access. This
allows to remove _MMIO_PLL3() that is now unused.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-4-lucas.demarchi@intel.com
It's a constant pattern in the driver to need to use 2 ranges of MMIOs
based on port, phy, pll, etc. When that happens, instead of using
_PICK_EVEN(), _PICK() needs to be used. Using _PICK() is discouraged
due to some reasons like:
1) It increases the code size since the array is declared
in each call site
2) Developers need to be careful not to incur an
out-of-bounds array access
3) Developers need to be careful that the indexes match the
table. For that it may be that the table needs to contain
holes, making (1) even worse.
Add a variant of _PICK_EVEN() that works with 2 ranges and selects which
one to use depending on the index value.
v2: Fix the address expansion in the example (Anusha)
v3: Also rename macro to _PICK_EVEN_2RANGES() in the documentation
and reword it to clarify what ranges are chosen based on the index
(Jani)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125182403.7526-1-lucas.demarchi@intel.com
