The VAR-SOM-MX93 features Dual Freescale/NXP PCA9541 chip as a Power
Management Integrated circuit (PMIC).
The PMIC is programmable via the I2C interface and its associated
register map, and this patch adds its support.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree nodes for the WiFi and Bluetooth module mounted on the
VAR-SOM-MX93. The module can be based on either the NXP IW612 or IW611
chipset, depending on the configuration chosen by the customer.
Regardless of the chipset used, WiFi communicates over SDIO and Bluetooth
over UART.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the lpuart1 dts node to support the PCIE9098 bluetooth on M.2
connector.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add phandle to the OCOTP mac-address nodes so the FEC can obtain a fixed
MAC address specific to each board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
default, state_100mhz and state_200mhz use the same settings. But current
driver use these to indicate if sd3.0 support.
Add SD gpio pin group (Reset, CD, WP) for usdhc2.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign double SD bus frequency to support SDR104 mode, where the operating
clock runs at 208 MHz.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
default, state_100mhz and state_200mhz use the same settings. But current
driver use these to indicate if sd3.0 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add overlay to support PWM fan on the phyBOARD-Nash-i.MX93 board. Fan
can be connected to the FAN (X48) connector on the board and will be
controlled according to the following CPU temperature trips table:
- bellow 50 degrees - fan is off (<1% duty cycle)
- between 50 and 58 degrees - low fan speed (~35% duty cycle)
- between 58 and 65 degrees - fan medium speed (~60% duty cycle)
- above 65 degrees - fan at full speed (>99% duty cycle)
The output frequency of PWM signal is set to 25 kHz.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Alberto Merciai <alb3rt0.m3rciai@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable internal pull up of the active low audio codec reset pin.
Otherwise the audio codec does not reset properly and is not working.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for powertip,ph128800t006-zhc01 connected via peb-av-10
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PEB-AV-10 board can be used with different displays or in audio-only
mode.
Split the device tree overlays to reflect these use cases. To use the
board with the EDT ETML1010G3DRA display, the overlay
imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtbo must now be used
instead of imx8mm-phyboard-polis-peb-av-10.dtbo.
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
sn65dsi83 is mounted on som. Add the static configuration there.
So it can be used by other boards too.
Use mipi_dsi_out from imx8mm.dtsi directly.
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We used regulator-settling-time-us for the wifi regulator which is
wrong for regulator-fixed. We have to use startup-delay-us instead.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This sets in_voltage_scale to calculate the measured voltage from the
raw digital value of the ADC.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Functionality has been added without removing the associated TODO
comments.
Clean that up by removing TODOs no longer applicable.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The HDMI TX Parallel Audio Interface (HTX_PAI) is a bridge between the
Audio Subsystem to the HDMI TX Controller.
Shrink register map size of hdmi_pvi to avoid overlapped hdmi_pai device.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector(PCIe0) on i.MX95 19x19 EVK board.
PCIe1 uses one standard PCIe slot connector, but combines the +3.3v and
+3.3Vaux into a same 3.3v power source, and intends to let it always on.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe1 on i.MX95 19x19 EVK board too.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX95 15x15 EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8QXP MEK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8QM MEK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8MQ EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8MP EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8DXL EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8qxp-mek matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8qm-mek matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8mq-evk matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8mp-evk matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8mm-evk matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx95-19x19-evk matches this requirement, so add supports-clkreq to
allow PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx95-15x15-evk matches this requirement, so add supports-clkreq to
allow PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RTL8211E ethernet PHY on the Debix Model A board it located at
address 1. Replace the broadcast address with the correct unicast
address.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
