The reset button on imx8mm-evk is tied to PWRON_B pin of bd71847 and the
long press duration is set to zero from OTP. The linux driver overrides
those values and breaks reset from button.
Overwriting OTP or bootloader configuration with some hardcoded defaults
is not desirable, keep already programmed values instead.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Register driver when EC indicates has precise lid angle calculation code
running.
Fix incorrect extra resource allocation in cros_ec_sensors_register().
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MODULE_DEVICE_TABLE(of, <of_match_table>) should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo ./drivers/mfd/madera.ko | grep alias
After this patch:
modinfo ./drivers/mfd/madera.ko | grep alias
alias: of:N*T*Ccirrus,wm1840C*
alias: of:N*T*Ccirrus,wm1840
alias: of:N*T*Ccirrus,cs47l91C*
alias: of:N*T*Ccirrus,cs47l91
alias: of:N*T*Ccirrus,cs47l90C*
alias: of:N*T*Ccirrus,cs47l90
alias: of:N*T*Ccirrus,cs47l85C*
alias: of:N*T*Ccirrus,cs47l85
alias: of:N*T*Ccirrus,cs47l35C*
alias: of:N*T*Ccirrus,cs47l35
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the LP87565_DEVICE_TYPE_LP87561_Q1 case does not have a
break statement, causing it to fall through to a dev_err message.
Fix this by adding in the missing break statement.
Addresses-Coverity: ("Missing break in switch")
Fixes: 7ee63bd747 ("regulator: lp87565: Add 4-phase lp87561 regulator support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
RK809 and RK817 are power management IC chips for multimedia products.
most of their functions and registers are same, including the clkout
funciton.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
RK809 and RK817 are power management IC chips for multimedia products.
Most of their functions and registers are same, including the rtc.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the rk809 and rk817 regulator driver.
Their specifications are as follows：
1. The RK809 and RK809 consist of 5 DCDCs, 9 LDOs
and have the same registers for these components except dcdc5.
2. The dcdc5 is a boost dcdc for RK817 and is a buck for RK809.
3. The RK817 has one switch but The Rk809 has two.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Mark Brown <broonie@kernel.org>
[rebased on top of 5.2-rc1]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK809 and RK817 are a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators
- RTC
- Clocking
Both RK809 and RK817 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Most of regulators have a some implementation also.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Support RTC block in ROHM bd70528 power management IC. Support
getting and setting the time and date as well as arming an alarm
which can also be used to wake the PMIC from standby state.
HW supports wake interrupt only for the next 24 hours (sec, minute
and hour information only) so we limit also the alarm interrupt to
this 24 hours for the sake of consistency.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ROHM BD70528 PMIC has 4 GPIO pins. Allow them to be
controlled by GPIO framework.
IRQs are handled by regmap-irq and GPIO driver is not
aware of the irq usage.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Document bindings for regulators (3 bucks, 3 LDOs and 2 LED
drivers) and 4 GPIO pins which can be configured for I/O or
as interrupt sources withe configurable trigger levels.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ROHM BD70528 is an ultra low power PMIC with similar 32K clk as
bd718x7. Only difference (from clk perspective) is register address.
Add support for controlling BD70528 clk using bd718x7 driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ROHM BD70528MWV is an ultra-low quiescent current general
purpose single-chip power management IC for battery-powered
portable devices.
Add MFD core which enables chip access for following subdevices:
- regulators/LED drivers
- battery-charger
- gpios
- 32.768kHz clk
- RTC
- watchdog
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Split the bd718x7.h to ROHM common and bd718x7 specific parts
so that we do not need to add same things in every new ROHM
PMIC header. Please note that this change requires changes also
in bd718x7 sub-device drivers for regulators and clk.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The LP8756x family has a single output 4-phase regulator
configuration. Add support for the same. The control
lies in the master buck which is buck0 for 4-phase
configuration. Enable/disable/voltage set happen via
buck0 registers.
Data Sheet: https://www.ti.com/lit/ds/symlink/lp87561-q1.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To reduce code and improve performance of the embedded controller
firmware, pragma __aligned(2) or __aligned(4) are used when alignment to
16 or 32 bit boundary is expected.
Define all ec_align to packed when compiling kernel.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
