When performing indirect read via external DMA the timeout for
completion is set equal to the read length instead of fixed timeout value.
For reads larger than 500 bytes, the timeout will continue to be
equal to the read length whereas for a small read like the Read Status
Register command, the timeout would be 1 or 2 milliseconds. This is not
enough to cover the overhead needed in setting up DMA, in that case make
sure the timeout is at least 500ms to allow DMA to finish. This solution
is inline with the timeout used for Direct read via DMA.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Link: https://lore.kernel.org/r/20230320095931.2651714-2-sai.krishna.potthuri@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>:
This patch series fixes the following bugs in spi-pci1xxxx driver:
1. Length of SPI transactions is improper
2. SPI transactions fail after suspend and resume
3. Incorrect implementation of pci1xxxx_spi_set_cs API
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
CPM has the same problem as QE so for CPM also use the fix added
by commit 0398fb7094 ("spi/spi_mpc8xxx: Fix QE mode Litte Endian"):
CPM mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for 16 and 32 bits
words. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also limit the workaround to 16 and 32 bits words because it can
only work for multiples of 8-bits.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 0398fb7094 ("spi/spi_mpc8xxx: Fix QE mode Litte Endian")
Link: https://lore.kernel.org/r/1b7d3e84b1128f42c1887dd2fb9cdf390f541bc1.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
After fixing the error handling in the .remove() callback of the qup
driver, convert it to .remove_new() preparing to make platform driver's
remove functions return void.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230330210341.2459548-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20230318222132.3373-1-kgroeneveld@lenbrook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Convert this driver from always returning zero in the remove callback to
the void returning variant.
Now that bcm2835_spi_remove returns no error code any more,
bcm2835_spi_shutdown() does the same thing as bcm2835_spi_remove(). So
drop the shutdown function and use bcm2835_spi_remove() as .shutdown
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230330211022.2460233-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
An early error return from a remove callback is usally wrong. In the
case of the spi-sprd driver it's not that critical because the skipped
steps are mainly undoing the things that a successful runtime-resume
would have done.
Still it's cleaner to not exit early and not return an (mostly ignored)
error value. The second patch converts to .remove_new (which is the
motivation for this series).
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
This small series converts the spi-imx driver to .remove_new(). The
motivation for this tree-wide effort are drivers that don't properly
cleanup and return an error code. This is broken as this results in
resource leaks. The spi-imx driver is such a driver. The idea is that if
the remove callback returns void it's obvious that an early error return
is wrong.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230306065733.2170662-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307211426.2331483-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If pm_runtime_resume_and_get() failed before this change, two error
messages were printed. One directly in sprd_spi_remove() and another
by the device core as the return value is non-zero.
The better handling of a failure to resume the device is to do the
software related cleanup anyhow and only skip hardware accesses.
This leaves the device in an unknown state, but there is nothing that can
be done about that.
Even in the error case, return zero to suppress the device core's error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307211426.2331483-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
This series converts the atmel-quadspi driver to use the .remove_new()
callback that doesn't return an int but void. The motivation is to not
give driver authors a reason to (wrongly) believe that returning an
error code was sensible error handling. In fact the spi core only emits
a warning message in this case and otherwise continues as if the return
value was zero. This usually yields resource leaks that sometimes can
lead to exceptions later on.
The atmel-quadspi driver is one of these drivers that got error handling
wrong, this is fixed here and in the last patch the driver is converted
to .remove_new() with the eventual goal to change .remove() to return
void once all drivers are converted this way.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20230317084232.142257-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
An early error exit in atmel_qspi_remove() doesn't prevent the device
unbind. So this results in an spi controller with an unbound parent
and unmapped register space (because devm_ioremap_resource() is undone).
So using the remaining spi controller probably results in an oops.
Instead unregister the controller unconditionally and only skip hardware
access and clk disable.
Also add a warning about resume failing and return zero unconditionally.
The latter has the only effect to suppress a less helpful error message by
the spi core.
Fixes: 4a2f83b7f7 ("spi: atmel-quadspi: add runtime pm support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20230317084232.142257-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The TSIZE register in CR2, to which the number of words to transfer
is written, is only 16 Bit. This limits transfers to 65535 SPI
_words_ at a time. The existing code uses spi_split_transfers_maxsize
to limit transfers to 65535 _bytes_ at a time.
This breaks large transfers with bits_per_word > 8, as they are
split inside of a word boundary by the odd size limit.
Split transfers based on the number of words instead.
This has the added benefit of not artificially limiting the maximum
length of bpw > 8 transfers to half or a quarter of the actual limit.
The combination of very large transfers and bits_per_word = 16 is triggered
e.g. by MIPI DBI displays when updating large parts of the screen.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/20230310092053.1006459-2-l.goehrs@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_split_transfers_maxwords() function that splits
spi_transfers transparently into multiple transfers
that are below a given number of SPI words.
This function reuses most of its code from
spi_split_transfers_maxsize() and for transfers with
eight or less bits per word actually behaves the same.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Link: https://lore.kernel.org/r/20230310092053.1006459-1-l.goehrs@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
With commit 721da5cee9 ("driver core: remove CONFIG_SYSFS_DEPRECATED and
CONFIG_SYSFS_DEPRECATED_V2"), ./scripts/checkkconfigsymbols.py indicated
an unresolved reference to the config SYSFS_DEPRECATED in the SPI summary
documentation.
Simply, delete the sentence referring to the removed config there. Also
update the documentation, as these sys/class entries should always be
symlinks, as the commit message of the commit above suggests.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230314075609.5232-1-lukas.bulwahn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Geert Uytterhoeven <geert+renesas@glider.be>:
After noticing new cases of casting away constness, I went over all
spi_get_*() functions and their callers, and made the following changes:
1. Make all pointer parameters const where possible,
2. Remove unneeded casts, some not even related to constness.
