Currently, the mac80211 layer handles construction and parsing
of 802.11 headers during packet transmission and reception.
Offloading encapsulation and decapsulation to hardware can
significantly enhance performance. Check the service bit to determine
if the firmware supports Ethernet offload. If supported, advertise the
capability to mac80211 to bypass software-based 802.11 header
processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00217-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718025513.32982-4-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the ath12k driver supports only the native Wi-Fi
frame format. In this mode, the ieee80211_tx_status() function
works correctly to report transmission status to mac80211, as
it retrieves station information using sta_info_get_by_addrs().
However, this method is not applicable for Ethernet-converted
packets, since sta_info_get_by_addrs() cannot extract station
information from such formats.
Retrieve station information using ath12k_peer_find_by_id() to
support all frame formats, including native Wi-Fi, raw, and Ethernet.
Report transmission status using ieee80211_tx_status_ext(), and
include rate information as part of the datapath TX status report.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00217-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718025513.32982-3-nithyanantham.paramasivam@oss.qualcomm.com
[changed instances of { 0 } to {}]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the transmit (TX) direction, EAPOL, QoS NULL,
and multicast frames are sent in native Wi-Fi (802.11) format.
However, when the virtual interface is configured in Ethernet
mode, transmission fails for packets enqueued in native Wi-fi format.
To address this issue, the firmware should be instructed to
treat these packets as RAW type packets, ensuring proper
handling even when the interface operates in Ethernet mode.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00217-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718025513.32982-2-nithyanantham.paramasivam@oss.qualcomm.com
[fix indentation]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Update the host logic to dynamically parse WMI extended service
bits beyond the current fixed size of 4 * 32 (i.e., 384 bits)
after WMI_MAX_EXT_SERVICE (256).
The current implementation misses service bits advertised beyond this
range, leading to not enabling some of the features supported by firmware.
Implement dynamic length parsing to iterate up to the maximum
service bit index advertised by the firmware.
This ensures all supported features are correctly recognized and enabled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00217-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250717173539.2523396-3-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath11k_mac_disable_peer_fixed_rate() is passed as the iterator to
ieee80211_iterate_stations_atomic(). Note in this case the iterator is
required to be atomic, however ath11k_mac_disable_peer_fixed_rate() does
not follow it as it might sleep. Consequently below warning is seen:
BUG: sleeping function called from invalid context at wmi.c:304
Call Trace:
<TASK>
dump_stack_lvl
__might_resched.cold
ath11k_wmi_cmd_send
ath11k_wmi_set_peer_param
ath11k_mac_disable_peer_fixed_rate
ieee80211_iterate_stations_atomic
ath11k_mac_op_set_bitrate_mask.cold
Change to ieee80211_iterate_stations_mtx() to fix this issue.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250603-ath11k-use-non-atomic-iterator-v1-1-d75762068d56@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently host sends HTT_TCL_METADATA_VER_V2 to the firmware
regardless of the operating mode (Mission or FTM).
Firmware expects additional software information (like peer ID, vdev
ID, and link ID) in Tx packets when HTT_TCL_METADATA_VER_V2 is set.
However, in FTM (Factory Test Mode) mode, no vdev is created on the
host side (this is expected). As a result, the firmware fails to find
the expected vdev during packet processing and ends up dropping
packets.
To fix this, send HTT_TCL_METADATA_VER_V1 in FTM mode because FTM
mode doesn't support HTT_TCL_METADATA_VER_V2.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: 5d964966bd ("wifi: ath12k: Update HTT_TCL_METADATA version and bit mask definitions")
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250711035420.1509029-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
A multi-link client can use any link for transmissions. It can decide to
put one link in power save mode for longer periods while listening on the
other links as per MLD listen interval. Unicast management frames sent to
that link station might get dropped if that link station is in power save
mode or inactive. In such cases, firmware can take decision on which link
to use.
Allow the firmware to decide on which link management frame should be
sent on, by filling the hardware link with maximum value of u32, so that
the firmware will not have a specific link to transmit data on and so
the management frames will be link agnostic. For QCN devices, all action
frames are marked as link agnostic. For WCN devices, if the device is
configured as an AP, then all frames other than probe response frames,
authentication frames, association response frames, re-association response
frames and ADDBA response frames are marked as link agnostic and if the
device is configured as a station, then all frames other than probe request
frames, authentication frames, de-authentication frames and ADDBA response
frames are marked as link agnostic.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250711091704.3704379-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, host sends num_tids (number of TID (Traffic Identifier))
value to firmware via WMI_INIT_CMD during WMI initialization. However,
the firmware does not use this value, as it determines the number of
TIDs using its own internal logic.
Hence, remove the redundant num_tids calculation logic for QCN9274.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250708181102.4111054-3-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce ath12k_mem_profile_based_param structure to define
configuration parameters for both default and low-memory profiles.
Add support for enabling the low-memory profile in the follow-up
patch by making the following changes:
- Reduce sizes for transmit, receive, and monitor descriptor rings.
- Reduce transmit and receive descriptor count.
- Limit the maximum number of virtual devices (vdevs) to 9.
- Reduce the maximum number of client support per radio.
Centralize these parameters in the ath12k_mem_profile_based_param
structure to simplify switching between memory profiles.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250708181102.4111054-2-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the ACK RSSI value is not shown in station dump. Enable WMI
resource flag for ACK RSSI in WMI INIT command to add ACK RSSI value in
management TX completion event from WMI. Update ACK RSSI value obtained
in management and data frame completion path to ieee80211_tx_info. Also
advertise NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT flag during hardware
register to mac80211 layer so that ACK RSSI is added to station dump
message.
Example output :
Station aa:bb:cc:dd:ee:ff (on wlp88s0)
inactive time: 46584 ms
rx bytes: 955
rx packets: 10
tx bytes: 769
tx packets: 6
tx retries: 81
tx failed: 0
rx drop misc: 0
signal: -39 dBm
signal avg: -40 dBm
tx bitrate: 6.0 MBit/s
tx duration: 1185 us
rx bitrate: 309.7 MBit/s 40MHz HE-MCS 6 HE-NSS 2 HE-GI 0 HE-DCM 0
rx duration: 0 us
last ack signal:-41 dBm
avg ack signal: -40 dBm
authorized: yes
authenticated: yes
.......
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sivashankari Madhavan <quic_sivamadh@quicinc.com>
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250709133554.622463-1-quic_ssreeela@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Install beacon protection keys in hardware for AP modes only if hardware
supports it, as indicated by the WMI service bit
WMI_TLV_SERVICE_BEACON_PROTECTION_SUPPORT. Allow keyidx up to 7, since
beacon protection uses keyidx 6 and 7.
Control this feature by setting bit 0 of feature_enable_bitmap when sending
the WMI_BCN_TMPL_CMDID command to firmware.
Check for the beacon protection enabled bit in both tx and non-tx profiles
for MBSSID cases. If set in either profile, enable the beacon protection
feature in firmware for transmitted vif.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <karthikeyan.kathirvel@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250604101620.2948103-1-karthikeyan.kathirvel@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Packets delivered to mac80211 from the WBM error path currently do not
have the RX_FLAG_SKIP_MONITOR flag set in status->flag. As a result,
mac80211 performs unnecessary monitor mode checks on each packet, even
though these packets are not intended for monitor mode processing.
In regular rx path, this flag is explicitly set to avoid such overhead.
Align the WBM error path behavior by setting RX_FLAG_SKIP_MONITOR to
prevent redundant per-packet checks in mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605050135.1802902-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In order to ensure the HTT DebugFS structs shared with firmware have
matching alignment, the structs should be packed. Most of the structs
are correctly packed, however the following are not:
ath12k_htt_tx_pdev_rate_stats_tlv
ath12k_htt_rx_pdev_rate_stats_tlv
ath12k_htt_rx_pdev_rate_ext_stats_tlv
So pack those structs.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: ba42b22aa3 ("wifi: ath12k: Dump PDEV transmit rate HTT stats")
Fixes: a24cd75830 ("wifi: ath12k: Dump PDEV receive rate HTT stats")
Fixes: 7a3e8eec8d ("wifi: ath12k: Dump additional PDEV receive rate HTT stats")
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250702-debugfs_htt_packed-v1-1-07bd18b31e79@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The maximum bandwidth an interface can operate in is defined by the
configured country. However, currently, it is able to operate in
bandwidths greater than the allowed bandwidth. For example,
the Central African Republic (CF) supports a maximum bandwidth of 40 MHz
in both the 2 GHz and 5 GHz bands, but an interface is still able to
operate in bandwidths higher than 40 MHz. This issue arises because the
regulatory rules in the regd are not updated with these restrictions
received from firmware on the maximum bandwidth.
Hence, update the regulatory rules with unsupported bandwidth flags based
on the maximum bandwidth to ensure compliance with country-specific
regulations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Amith A <quic_amitajit@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250701135902.722851-1-quic_amitajit@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k driver maintains a counter to store the number of
stations connected to each radio. However, at certain times like
debugging, it is useful to know number of stations connected to any
one of the interface in that radio.
Add support to maintain a counter for number of stations connected to
each interface.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250630044531.3490058-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the HTT_H2T_MSG_TYPE_PPDU_STATS_CFG request uses bits
8 to 15 as the bitmask for HTT_PPDU_STATS_CFG_PDEV_ID for firmware
PPDU_STATS. However, bit 8 is reserved for SOC stats, and the actual
PDEV ID should be encoded using bits 9 to 15. This leads to incorrect
PDEV ID encoding in the request, causing it to either ignore the
request or apply it to the wrong PDEV.
Additionally, pdev_mask calculation is done as
pdev_mask = 1 << (i + 1); (i.e. i= num_rxmda_per_pdev)
but this is not valid for multiple pdevs(multi-MAC configurations)
with 1 rxdma per pdev, as this will mask the same value for all pdevs.
To correctly identify each and exact MAC in multi-MAC configurations,
the calculation should include ar->pdev_idx:
pdev_mask = 1 << i + ar->pdev_idx;
Due to these issues, the firmware does not send PPDU_STATS for the
intended PDEV, leading to inaccurate and incomplete statistics on the
host. This might trigger certain WARN_ON() conditions in host that
rely on these statistics.
Hence, change the bitmask for HTT_PPDU_STATS_CFG_PDEV_ID as bit 9
to 15 to properly fill the pdev id in request message and change
the pdev_mask calculation to consider ar->pdev_idx to mask pdev
correctly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250630064431.3446333-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Ensure that all radios remain down when the driver operates in Factory
Test Mode (FTM). Reject any userspace attempts to bring up an
interface in this mode.
Currently, the driver allows userspace to bring up the interface even
though it operates in FTM mode, which violates FTM constraints and
leads to FTM command failures.
Hence, block the radio start when the driver is in FTM mode. Also,
remove ath12k_ftm_mode check from ath12k_drain_tx() because FTM mode
check is already handled in the caller function
(ath12k_mac_op_start()).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 3bc374cbc4 ("wifi: ath12k: add factory test mode support")
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250630031502.8902-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For certain action frames like the TPC Report IE in the spectrum management
TPC Report action frame, and in the Radio Measurement Link Measurement
Report action frame there is a requirement to fill in the current
and max Tx power of the device in the packet.
Add support to populate these fields in the relevant packets.
In software-encrypted cases such as PMF, skip insertion since the packets
are already encrypted and cannot be modified.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250630-support-for-tx-power-insertion-v1-1-77f45484d5bb@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, tx_retries and tx_failed are updated only in mac80211 during
tx_completion path for sta->deflink. This works fine for non-ML
station but for multi-link (ML) station, these values should be updated
for sta->link[link_id] as per tx link_id. However, in tx_completion path
there is no way to determine the link_id for which packet is retried or
failed.
Therefore, update the tx_retries and tx_failed in arsta structure from
htt_ppdu_stats_user_cmpltn_common_tlv during
ath12k_update_per_peer_tx_stats() call to utilize the values from arsta.
Also, during 'iw dev xxxx station dump' populate the tx_retries and
tx_failed in station_info structure to ensure values are correctly
reflected.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250701105927.803342-6-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, statistics in arsta are updated at deflink for both non-ML
and multi-link(ML) station. Link statistics are not updated for
multi-link operation(MLO).
Hence, add support to correctly obtain the link ID if the peer is ML,
fetch the arsta from the appropriate link ID, and update the
statistics in the corresponding arsta.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250701105927.803342-3-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently rx and tx MCS map for 160 MHz under HE capabilities
are not updating properly, when 160 MHz is configured with NSS
lesser than max NSS support. Fix this by utilizing
nss_ratio_enabled and nss_ratio_info fields sent by firmware
in service ready event.
However, if firmware advertises EXT NSS BW support in VHT caps
as 1(1x2) and when nss_ratio_info indicates 1:1, reset the EXT
NSS BW Support in VHT caps to 0 which indicates 1x1. This is
to avoid incorrectly choosing 1:2 NSS ratio when using the
default VHT caps advertised by firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-10-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to configure maximum NSS in 160 MHz bandwidth.
Firmware advertises support for handling NSS ratio information
as a part of service ready ext event using nss_ratio_enabled
flag. Save this information in ath12k_pdev_cap to calculate
NSS ratio.
Additionally, reorder the code by moving
ath12k_peer_assoc_h_phymode() before ath12k_peer_assoc_h_vht()
to ensure that arg->peer_phymode correctly reflects the bandwidth
in the max NSS calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-9-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In rare cases, ath10k may lose connection with the PCIe bus due to
some unknown reasons, which could further lead to system crashes during
resuming due to watchdog timeout:
ath10k_pci 0000:01:00.0: wmi command 20486 timeout, restarting hardware
ath10k_pci 0000:01:00.0: already restarting
ath10k_pci 0000:01:00.0: failed to stop WMI vdev 0: -11
ath10k_pci 0000:01:00.0: failed to stop vdev 0: -11
ieee80211 phy0: PM: **** DPM device timeout ****
Call Trace:
panic+0x125/0x315
dpm_watchdog_set+0x54/0x54
dpm_watchdog_handler+0x57/0x57
call_timer_fn+0x31/0x13c
At this point, all WMI commands will timeout and attempt to restart
device. So set a threshold for consecutive restart failures. If the
threshold is exceeded, consider the hardware is unreliable and all
ath10k operations should be skipped to avoid system crash.
fail_cont_count and pending_recovery are atomic variables, and
do not involve complex conditional logic. Therefore, even if recovery
check and reconfig complete are executed concurrently, the recovery
mechanism will not be broken.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623022731.509-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During interface creation, following print is observed on the console -
Timeout while waiting for regulatory update
This occurs due to commit 906619a009 ("wifi: ath12k: handle regulatory
hints during mac registration"), which introduced a completion mechanism to
synchronize the regulatory update process. The intent behind this change is
to coordinate the timing between when the firmware sends regulatory data to
the driver and when the driver processes that data.
However, during interface addition, if the 6 GHz band is active, the driver
invokes ath12k_regd_update() to apply the appropriate 6 GHz power mode
regulatory settings. At this point, there is no interaction with the
firmware, so the completion object is not reinitialized. As a result,
wait_for_completion() eventually times out, leading to the observed error
log message.
Hence to fix this, move all complete() on regd_update_completed to
complete_all().
The complete() function signals only once, causing any subsequent waits
without reinitialization to timeout. In this scenario, since waiting is
unnecessary, complete_all() can be used instead, ensuring that subsequent
calls to wait without reinitialization will simply bail out and not
actually wait. This approach is ideal because if the firmware is not
involved, there is no need to wait for the completion event. However, if
the firmware is involved, it is guaranteed that the completion will be
reinitialized, and thus, it would wait.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-by: Kang Yang <kang.yang@oss.qualcomm.com>
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 906619a009 ("wifi: ath12k: handle regulatory hints during mac registration")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250626-fix_timeout_during_interface_creation-v1-1-90a7fdc222d4@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When setting a new bitrate, WMI peer association command is sent from
the host without the peer authentication bit set in peer_flags for
security mode, which causes ping failure.
The firmware handles peer_flags when the client is associating, as the
peer authentication bit in peer_flags is set after the key exchange.
When the WMI peer association command is sent from the host to update
the new bitrate for an associated STA, the firmware expects the WMI
peer authentication bit to be set in peer_flags.
Fix this issue by ensuring that the WMI peer auth bit is set in
peer_flags in WMI peer association command when updating the new
bitrate.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Thiraviyam Mariyappan <thiraviyam.mariyappan@oss.qualcomm.com>
Signed-off-by: Ramasamy Kaliappan <ramasamy.kaliappan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250608145651.1735236-1-ramasamy.kaliappan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
