Adding the #address-cells/#size-cells properties without also
adding the other required properties for PCI nodes causes new
build warnings from dtc that now show up everywhere, rather than
just while verifying the yaml bindings:
arch/arm/boot/dts/bcm5301x.dtsi:240.21-246.5: Warning (pci_bridge): /axi@18000000/pcie@12000: missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/bcm5301x.dtsi:248.21-254.5: Warning (pci_bridge): /axi@18000000/pcie@13000: missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/bcm5301x.dtsi:256.21-262.5: Warning (pci_bridge): /axi@18000000/pcie@14000: missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dtb: Warning (unit_address_format): Failed prerequisite 'pci_bridge'
Revert it for now.
Fixes: 61dc1e3850 ("ARM: dts: BCM5301X: Add basic PCI controller properties")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM and ARM64 changes for v6.1
Late cleanup and fixes for Samsung DTS:
1. Fix polarity of pins:
- enable GPIO of NFC chip in Exynos5433 TM2 boards,
- vbus GPIO of EHCI in Exynos4412 Origen board.
2. Correct name of pin configuration nodes - redundant "pins" in the
name (no functional impact).
* tag 'samsung-dt-dt64-6.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5pv210: correct double "pins" in pinmux node
ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
arm64: dts: exynos: fix polarity of "enable" line of NFC chip in TM2
Link: https://lore.kernel.org/r/20221003073916.12588-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to s3fwrn5 driver code the "enable" GPIO line is driven "high"
when chip is not in use (mode is S3FWRN5_MODE_COLD), and is driven "low"
when chip is in use.
s3fwrn5_phy_power_ctrl():
...
gpio_set_value(phy->gpio_en, 1);
...
if (mode != S3FWRN5_MODE_COLD) {
msleep(S3FWRN5_EN_WAIT_TIME);
gpio_set_value(phy->gpio_en, 0);
msleep(S3FWRN5_EN_WAIT_TIME);
}
Therefore the line described by "en-gpios" property should be annotated
as "active low".
The wakeup gpio appears to have correct polarity (active high).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220929011557.4165216-1-dmitry.torokhov@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The generic platform driver pcie-designware-plat.c doesn't work for
UniPhier PCIe host controller, because the controller has some
necessary initialization sequence for the controller-specific logic.
Currently the controller doesn't use "snps,dw-pcie" compatible,
so this is no longer needed. Remove the compatible string from the
pcie node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-10-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to gpio-hog schema, should add the suffix "-hog" to the node
names including gpio-hog to fix the following warning.
uniphier-ld11-ref.dtb: gpio@55000000: 'xirq0' does not match any of the regexes: '^.+-hog(-[0-9+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml
This applies to the devicetre for LD11, LD20 and PXs3 SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-5-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The generic platform driver pcie-designware-plat.c doesn't work for
UniPhier PCIe endpoint controller, because the controller has some
necessary initialization sequence for the controller-specific logic.
Currently the controller doesn't use "snps,dw-pcie-ep" compatible,
so this is no longer needed. Remove the compatible string from the
pcie-ep node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042249.4708-10-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to gpio-hog schema, should add the suffix "-hog" to the node
names including gpio-hog to fix the following warning.
uniphier-pro4-ref.dtb: gpio@55000000: 'xirq2' does not match any of the regexes: '^.+-hog(-[0-9+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml
This applies to the devicetree for LD4, LD6b, Pro4 and sLD8 SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042249.4708-5-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
RK3399-Nanopi-R4S-enterprise as variant board, Gru-Scarlet SKU variants,
DSI support for rk356x, display-gamma-control for rk3399, display
output for quartz64-b and rk3566-roc-pc, hdmi supplies for rk3399-roc-pc,
some pinctrl improvements for the px30-evb and a number of changes to
bring rk3399 rock4 and rock-pi4 structure closer to names used in schematics.
* tag 'v6.1-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: use pin constant for reset-gpios on px30-evb
arm64: dts: rockchip: add pinctrl for mipi-pdn pin on px30-evb
arm64: dts: rockchip: set max drive-strength for cif_clkout_m0 on px30-evb
arm64: dts: rockchip: add avdd-0v9-supply and avdd-1v8-supply on rk3399 rock 4c and pi4
arm64: dts: rockchip: sort nodes/properties on rk3399-rock-4
arm64: dts: rockchip: fix regulator name on rk3399-rock-4
arm64: dts: rockchip: sort nodes/properties on rk3399-rock-4c-plus
arm64: dts: rockchip: fix regulator structure on rk3399-rock-4c-plus
arm64: dts: rockchip: connect vcca_1v8 to APIO5_VDD on rk3399-rock-4c-plus
arm64: dts: rockchip: Add DSI and DSI-DPHY nodes to rk356x
arm64: dts: rockchip: Enable HDMI and GPU on quartz64-b
arm64: dts: rockchip: Add RK3399 NanoPi R4S Enterprise Edition
dt-bindings: Add doc for FriendlyARM NanoPi R4S Enterprise Edition
arm64: dts: rockchip: add i2s0 I2S/PDM/TDM 8ch controller to px30
arm64: dts: rockchip: Add HDMI supplies on rk3399-roc-pc
arm64: dts: rockchip: Support gru-scarlet sku{2,4} variants
dt-bindings: arm: rockchip: Add gru-scarlet sku{2,4} variants
arm64: dts: rockchip: enable gamma control on RK3399
arm64: dts: rockchip: Enable video output on rk3566-roc-pc
Link: https://lore.kernel.org/r/38114097.10thIPus4b@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added IPMB-13 channel for Debug Card communication which improves the
readability of the machine and makes it easier to debug the server and
it will display some pieces of information about the server like "system
info", "Critical sensors" and "critical sel".
Signed-off-by: Karthikeyan Pasupathi <pkarthikeyan1509@gmail.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Link: https://lore.kernel.org/r/20220926124313.GA8400@hcl-ThinkPad-T495
Signed-off-by: Joel Stanley <joel@jms.id.au>
Devicetree changes for omaps
A series of changes for am335x baltos and netcom devices to update nand
transfer type and configure gpio-line-names.
* tag 'omap-for-6.1/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-netcom: add GPIO names for NetCom Plus 2-port devices
ARM: dts: am335x-netcom: add GPIO names for NetCom Plus 8-port devices
ARM: dts: am335x-netcan: add GPIO names for NetCAN Plus device
ARM: dts: am335x-baltos: add GPIO names for ir2110 device
ARM: dts: am335x-baltos: add GPIO names for ir3220 and ir5221 devices
ARM: dts: am335x-baltos: change nand-xfer-type
Link: https://lore.kernel.org/r/pull-1663587735-853102@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Device tree label property should contain label from the box/stick.
Labels for other ports are already specified in DT but wan is missing.
So add missing label for wan port.
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Turris Omnia has GPIO51 exported on pin header U16, which works in S/PDIF
output mode. So define S/PDIF audio output card for this pin.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
S/PDIF function on Armada 38x uses only mpp51 pin. So add spdif-pins mpp
pins section for it. It is needed for boards without i2s.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This commit adds the necessary Device Tree information to enable
audio support on the Armada 385 DB platform. In details it:
* Instantiates the CS42L51 audio codec on the I2C0 bus
* Adds simple-card DT binding for audio on Armada 385 DB
* Adds description for both analog I2S and S/PDIF I/O
* Disabled by default
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Tested-by: Star_Automation <star@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Qualcomm ARM64 DTS updates for 6.1
Support for Samsung Galaxy E5, E7 and Grand Max is added, with support
for both 32-bit and 64-bit variants. The Samsung Galaxy S4 Mini Value
Edition gains magnetometer support.
MSM8996-based Xiaomi devices gains descriptions of the LPG-based LEDs.
On SA8295P ADP problems arising from regulators being switched into
low-power mode is worked around by removing this ability, for now.
The onboard USB Hub on SC7180 Trogdor is finally described and a few ADC
related updates are introduced.
On SC7280 support for the CPU and LLC bwmon instances are introduced.
Soundwire, audio codecs and sound introduced for a variety of boards.
Using required-opps the USB controllers votes for a minimum corner on
VDD_CX.
The onboard USB Hub Herobrine is described. A new board, the Google
Evoker is added, as is another revision of Herobrine Villager.
On SC8280XP the USB controllers are marked as wakeup-sources, to keep
them powered during suspend. The CRD has HID devices marked as
wakeup-sources to enable resuming the system. In addition to these
changes the alternative touchpad is introduced on the Lenovo ThinkPad
X13s.
SDM845 gains RPMh stats support and the LLCC BWMON is added. For SM6350
interconnect providers and GPI DMA is introduced. A description of the
PM7280b PMIC is added to Fairphone FP4 on SM7225.
With the multi-MSI support added in the PCIe controller, SM8250 gets all
its MSI interrupts added.
UFS ICE and the second SDHCI controller is introduced on SM8450. Support
for the Sony Xperia 1 IV is introduced.
Throughout a variety of platforms the TCSR mutex syscon is replaced with
the MMIO-based binding. TCSR nodes gained proper compatibles and halt
syscon nodes are split out from the mutex ranges.
A range of fixes to align with DT bindings are introduced. Among these
are the changes to the follow the TLMM binding and suffix pinctrl states
with -state and subnodes thereof with -pins, another is a number of
changes transitioning to use -gpios and introduction of proper parent
clock references in various clock providers.
* tag 'qcom-arm64-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (136 commits)
arm64: dts: qcom: sc7280: Add required-opps for USB
arm64: dts: qcom: sm8450: fix UFS PHY serdes size
arm64: dts: qcom: ipq8074: fix PCIe PHY serdes size
arm64: dts: qcom: sa8295p-adp: add missing gpio-ranges in PMIC GPIOs
arm64: dts: qcom: sa8295p-adp: add fallback compatible to PMIC GPIOs
arm64: dts: qcom: msm8996-xiaomi: align PMIC GPIO pin configuration with DT schema
arm64: dts: qcom: msm8994-msft-lumia-octagon: align resin node name with bindings
arm64: dts: qcom: pmi8994: add missing MPP compatible fallback
dt-bindings: pci: QCOM Add missing sc7280 aggre0, aggre1 clocks
arm64: dts: qcom: sc7280: Add missing aggre0, aggre1 clocks
arm64: dts: qcom: sc7280-villager: Adjust LTE SKUs
dt-bindings: arm: qcom: Adjust LTE SKUs for sc7280-villager
arm64: dts: qcom: sc7280-herobrine: Add nodes for onboard USB hub
arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub
arm64: dts: qcom: align SDHCI reg-names with DT schema
arm64: dts: qcom: sm8250: provide additional MSI interrupts
arm64: dts: qcom: msm8996: add #clock-cells and XO clock to the HDMI PHY node
arm64: dts: qcom: Use WCD9335 DT bindings
arm64: dts: qcom: msm8994: switch TCSR mutex to MMIO
arm64: dts: qcom: ipq6018: switch TCSR mutex to MMIO
...
Link: https://lore.kernel.org/r/20220921234854.1343238-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM DTS updates for 6.1
This adds extends the IPQ8064 support with the two variants IPQ8062 and
IPQ8065. MSM8974 and APQ8084 gained RPM stats support.
The Audio DSP remoteproc was added to MSM8226 and enabled for ASUS
ZenWatch 2 and LG G Watch R.
MSM8660 gained one I2C and one SPI bus and the APQ8060 Dragonboard got
the TMA340 Touchscreen described.
A wide range of improvements are done throughout the DTS files to align
with bindings, fix issues and improve structure on things.
* tag 'qcom-dts-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (35 commits)
ARM: dts: qcom: apq8026-lg-lenok: Enable ADSP
ARM: dts: qcom: apq8026-asus-sparrow: Enable ADSP
ARM: dts: qcom: msm8226: Add ADSP node
ARM: dts: qcom: ipq8064: pad addresses to 8 digit
ARM: dts: qcom: ipq8064: reorganize node order and sort them
ARM: dts: qcom: align SDHCI clocks with DT schema
ARM: dts: qcom: align SDHCI reg-names with DT schema
ARM: dts: qcom: msm8960: add clocks to the MMCC device node
ARM: dts: qcom: apq8064: add clocks to the MMCC device node
ARM: dts: qcom: msm8960: add clocks to the GCC device node
ARM: dts: qcom: apq8064: add clocks to the GCC device node
ARM: dts: qcom: msm8960: add clocks to the LCC device node
ARM: dts: qcom: apq8064: add clocks to the LCC device node
ARM: dts: qcom: msm8226: switch TCSR mutex to MMIO
ARM: dts: qcom: apq8084: switch TCSR mutex to MMIO
ARM: dts: qcom: msm8660: fix node names for fixed clocks
ARM: dts: qcom: msm8660: add pxo/cxo clocks to the GCC node
ARM: dts: qcom: apq8060-dragonboard: Add TMA340 to APQ8060 DragonBoard
ARM: dts: qcom: msm8660: Add GSBI3 I2C bus
ARM: dts: qcom: msm8660: Add GSBI1 SPI bus
...
Link: https://lore.kernel.org/r/20220921222619.1338380-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
