The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
While at it, let's also fix the size of the llcc_broadcast_base to cover
the whole region.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-6-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
On SC7180, there is only one LLCC bank available. So let's just pass that
as "llcc0_base".
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-5-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
On SDM845, the size of the LLCC bank 0 needs to be reduced to 0x4500 as
there are LLCC BWMON registers located after this range.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-4-manivannan.sadhasivam@linaro.org
First, move the pinctrl related propeties out from SoC dtsi and into the
board dts and add blank lines before status properties in the PHY nodes
to be consistent with the rest of the nodes. Then drop the pipe clock
from the controller nodes. Rename the aggre0 and aggre1 clocks to more
generic noc_aggr, and then the cnoc_pcie_sf_axi to cnoc_sf_axi. Add the
cpu-pcie interconnects to both controller nodes. Rename the pcie1 second
reset to link_down and drop the unnecessary enable-gpios. Switch the aux
clock to GCC_PCIE_1_PHY_AUX_CLK for the pcie1 PHY and drop the aux_phy
from clock-names. Also rename the nocsr reset to phy_nocsr. With this
changes we are now in line with the SC8280XP bindings.
Fixes: 7d1158c984 ("arm64: dts: qcom: sm8550: Add PCIe PHYs and controllers nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230208180020.2761766-12-abel.vesa@linaro.org
The Lenovo X13s firmware does not implement the UEFI time runtime
services so the RTC in the PM8280K PMIC needs to be accessed directly.
To complicate things further, the RTC control and time registers are
read-only on this platform so an offset must be stored in some other
machine-specific non-volatile memory which an RTC driver can take into
account when reading or updating the time.
The UEFI firmware (and Windows) use a UEFI variable for this:
882f8c2b-9646-435f-8de5-f208ff80c1bd-RTCInfo
but the offset can only be accessed via the Qualcomm UEFI Secure
Application residing in the TEE as the firmware does not implement the
variable runtime services either.
While it is possible to access this UEFI variable from Linux on the
X13s, this requires using a fairly complex and reverse-engineered
firmware interface. As the only benefit of doing so is to make sure that
the UEFI (Windows) and Linux time never gets out of sync, it seems
preferable to use the PMIC scratch registers for storing an offset
instead. This also avoids flash wear in case of RTC drift, etc.
So instead of using the UEFI RTC offset, reserve four bytes in one of
the PMIC SDAM scratch-register blocks to hold the RTC offset.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-23-johan+linaro@kernel.org
The SC8280XP CRD firmware does not implement the UEFI time runtime
services so the RTC in the PM8280K PMIC needs to be accessed directly.
To complicate things further, the RTC control and time registers are
read-only on this platform so an offset must be stored in some other
machine-specific non-volatile memory which an RTC driver can take into
account when reading or updating the time.
The UEFI firmware (and Windows) use a UEFI variable for this:
882f8c2b-9646-435f-8de5-f208ff80c1bd-RTCInfo
but the offset can only be accessed via the Qualcomm UEFI Secure
Application residing in the TEE as the firmware does not implement the
variable runtime services either.
While it is possible to access this UEFI variable from Linux on the CRD,
this requires using a fairly complex and reverse-engineered firmware
interface. As the only benefit of doing so is to make sure that the UEFI
(Windows) and Linux time never gets out of sync, it seems preferable to
use the PMIC scratch registers for storing an offset instead. This also
avoids flash wear in case of RTC drift, etc.
Also note that setting variables using this interface does not work on
at least one CRD for reasons not yet known.
So instead of using the UEFI RTC offset, reserve four bytes in one of
the PMIC SDAM scratch-register blocks to hold the RTC offset.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-22-johan+linaro@kernel.org
Commit aa47a7c215 ("lib/cpumask: deprecate nr_cpumask_bits") resulted
in the cpumask operations potentially becoming hugely less efficient,
because suddenly the cpumask was always considered to be variable-sized.
The optimization was then later added back in a limited form by commit
6f9c07be9d ("lib/cpumask: add FORCE_NR_CPUS config option"), but that
FORCE_NR_CPUS option is not useful in a generic kernel and more of a
special case for embedded situations with fixed hardware.
Instead, just re-introduce the optimization, with some changes.
Instead of depending on CPUMASK_OFFSTACK being false, and then always
using the full constant cpumask width, this introduces three different
cpumask "sizes":
- the exact size (nr_cpumask_bits) remains identical to nr_cpu_ids.
This is used for situations where we should use the exact size.
- the "small" size (small_cpumask_bits) is the NR_CPUS constant if it
fits in a single word and the bitmap operations thus end up able
to trigger the "small_const_nbits()" optimizations.
This is used for the operations that have optimized single-word
cases that get inlined, notably the bit find and scanning functions.
- the "large" size (large_cpumask_bits) is the NR_CPUS constant if it
is an sufficiently small constant that makes simple "copy" and
"clear" operations more efficient.
This is arbitrarily set at four words or less.
As a an example of this situation, without this fixed size optimization,
cpumask_clear() will generate code like
movl nr_cpu_ids(%rip), %edx
addq $63, %rdx
shrq $3, %rdx
andl $-8, %edx
callq memset@PLT
on x86-64, because it would calculate the "exact" number of longwords
that need to be cleared.
In contrast, with this patch, using a MAX_CPU of 64 (which is quite a
reasonable value to use), the above becomes a single
movq $0,cpumask
instruction instead, because instead of caring to figure out exactly how
many CPU's the system has, it just knows that the cpumask will be a
single word and can just clear it all.
Note that this does end up tightening the rules a bit from the original
version in another way: operations that set bits in the cpumask are now
limited to the actual nr_cpu_ids limit, whereas we used to do the
nr_cpumask_bits thing almost everywhere in the cpumask code.
But if you just clear bits, or scan for bits, we can use the simpler
compile-time constants.
In the process, remove 'cpumask_complement()' and 'for_each_cpu_not()'
which were not useful, and which fundamentally have to be limited to
'nr_cpu_ids'. Better remove them now than have somebody introduce use
of them later.
Of course, on x86-64 with MAXSMP there is no sane small compile-time
constant for the cpumask sizes, and we end up using the actual CPU bits,
and will generate the above kind of horrors regardless. Please don't
use MAXSMP unless you really expect to have machines with thousands of
cores.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto fix from Herbert Xu:
"Fix a regression in the caam driver"
* tag 'v6.3-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - Fix edesc/iv ordering mixup
Pull x86 updates from Thomas Gleixner:
"A small set of updates for x86:
- Return -EIO instead of success when the certificate buffer for SEV
guests is not large enough
- Allow STIPB to be enabled with legacy IBSR. Legacy IBRS is cleared
on return to userspace for performance reasons, but the leaves user
space vulnerable to cross-thread attacks which STIBP prevents.
Update the documentation accordingly"
* tag 'x86-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
virt/sev-guest: Return -EIO if certificate buffer is not large enough
Documentation/hw-vuln: Document the interaction between IBRS and STIBP
x86/speculation: Allow enabling STIBP with legacy IBRS
Pull irq updates from Thomas Gleixner:
"A set of updates for the interrupt susbsystem:
- Prevent possible NULL pointer derefences in
irq_data_get_affinity_mask() and irq_domain_create_hierarchy()
- Take the per device MSI lock before invoking code which relies on
it being hold
- Make sure that MSI descriptors are unreferenced before freeing
them. This was overlooked when the platform MSI code was converted
to use core infrastructure and results in a fals positive warning
- Remove dead code in the MSI subsystem
- Clarify the documentation for pci_msix_free_irq()
- More kobj_type constification"
* tag 'irq-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, platform-msi: Ensure that MSI descriptors are unreferenced
genirq/msi: Drop dead domain name assignment
irqdomain: Add missing NULL pointer check in irq_domain_create_hierarchy()
genirq/irqdesc: Make kobj_type structures constant
PCI/MSI: Clarify usage of pci_msix_free_irq()
genirq/msi: Take the per-device MSI lock before validating the control structure
genirq/ipi: Fix NULL pointer deref in irq_data_get_affinity_mask()
Pull vfs update from Al Viro:
"Adding Christian Brauner as VFS co-maintainer"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Adding VFS co-maintainer
Pull VM_FAULT_RETRY fixes from Al Viro:
"Some of the page fault handlers do not deal with the following case
correctly:
- handle_mm_fault() has returned VM_FAULT_RETRY
- there is a pending fatal signal
- fault had happened in kernel mode
Correct action in such case is not "return unconditionally" - fatal
signals are handled only upon return to userland and something like
copy_to_user() would end up retrying the faulting instruction and
triggering the same fault again and again.
What we need to do in such case is to make the caller to treat that as
failed uaccess attempt - handle exception if there is an exception
handler for faulting instruction or oops if there isn't one.
Over the years some architectures had been fixed and now are handling
that case properly; some still do not. This series should fix the
remaining ones.
Status:
- m68k, riscv, hexagon, parisc: tested/acked by maintainers.
- alpha, sparc32, sparc64: tested locally - bug has been reproduced
on the unpatched kernel and verified to be fixed by this series.
- ia64, microblaze, nios2, openrisc: build, but otherwise completely
untested"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
openrisc: fix livelock in uaccess
nios2: fix livelock in uaccess
microblaze: fix livelock in uaccess
ia64: fix livelock in uaccess
sparc: fix livelock in uaccess
alpha: fix livelock in uaccess
parisc: fix livelock in uaccess
hexagon: fix livelock in uaccess
riscv: fix livelock in uaccess
m68k: fix livelock in uaccess
include/linux/compiler-intel.h had no update in the past 3 years.
We often forget about the third C compiler to build the kernel.
For example, commit a0a12c3ed0 ("asm goto: eradicate CC_HAS_ASM_GOTO")
only mentioned GCC and Clang.
init/Kconfig defines CC_IS_GCC and CC_IS_CLANG but not CC_IS_ICC,
and nobody has reported any issue.
I guess the Intel Compiler support is broken, and nobody is caring
about it.
Harald Arnesen pointed out ICC (classic Intel C/C++ compiler) is
deprecated:
$ icc -v
icc: remark #10441: The Intel(R) C++ Compiler Classic (ICC) is
deprecated and will be removed from product release in the second half
of 2023. The Intel(R) oneAPI DPC++/C++ Compiler (ICX) is the recommended
compiler moving forward. Please transition to use this compiler. Use
'-diag-disable=10441' to disable this message.
icc version 2021.7.0 (gcc version 12.1.0 compatibility)
Arnd Bergmann provided a link to the article, "Intel C/C++ compilers
complete adoption of LLVM".
lib/zstd/common/compiler.h and lib/zstd/compress/zstd_fast.c were kept
untouched for better sync with https://github.com/facebook/zstd
Link: https://www.intel.com/content/www/us/en/developer/articles/technical/adoption-of-llvm-complete-icx.html
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
