Since the flip done event will be sent in the flip_done_handler,
no need to add the event to the list and delay it for later.
v2: -Moved the async check above vblank_get as it
was causing issues for PSR.
v3: -No need to wait for vblank to pass, as this wait was causing a
16ms delay once every few flips.
v4: -Rebased.
v5: -Rebased.
v6: -Rebased.
v7: -No need of irq disable if we are not doing vblank evade. (Ville)
v8: -Rebased.
v9: -Move the return in intel_pipe_update_end before tracepoint. (Ville)
v10: Rebased.
Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-5-karthik.b.s@intel.com
If flip is requested on any other plane, reject it.
Make sure there is no change in fbc, offset and framebuffer modifiers
when async flip is requested.
If any of these are modified, reject async flip.
v2: -Replace DRM_ERROR (Paulo)
-Add check for changes in OFFSET, FBC, RC(Paulo)
v3: -Removed TODO as benchmarking tests have been run now.
v4: -Added more state checks for async flip (Ville)
-Moved intel_atomic_check_async to the end of intel_atomic_check
as the plane checks needs to pass before this. (Ville)
-Removed crtc_state->enable_fbc check. (Ville)
-Set the I915_MODE_FLAG_GET_SCANLINE_FROM_TIMESTAMP flag for async
flip case as scanline counter is not reliable here.
v5: -Fix typo and other check patch errors seen in CI
in 'intel_atomic_check_async' function.
v6: -Don't call intel_atomic_check_async multiple times. (Ville)
-Remove the check for n_planes in intel_atomic_check_async
-Added documentation for async flips. (Paulo)
v7: -Replace 'intel_plane' with 'plane'. (Ville)
-Replace all uapi.foo as hw.foo. (Ville)
-Do not use intel_wm_need_update function. (Ville)
-Add destination coordinate check. (Ville)
-Do not allow async flip with linear buffer
on older hw as it has issues with this. (Ville)
-Remove break after intel_atomic_check_async. (Ville)
v8: -Rebased.
v9: -Replace DRM_DEBUG_KMS with drm_dbg_kms(). (Ville)
-Fix comment formatting. (Ville)
-Remove gen specific checks. (Ville)
-Remove irrelevant FB size check. (Ville)
-Add missing stride check. (Ville)
-Use drm_rect_equals() instead of individual checks. (Ville)
-Call intel_atomic_check_async before state dump. (Ville)
v10: -Fix the checkpatch errors seen on CI.
v11: -Use const for all plane/crtc states. (Ville)
-Use 'switch' instead of 'if' for modifier check. (Ville)
-Move documentation changes to a single patch. (Ville)
Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-4-karthik.b.s@intel.com
Add enable/disable flip done functions and the flip done handler
function which handles the flip done interrupt.
Enable the flip done interrupt in IER.
Enable flip done function is called before writing the
surface address register as the write to this register triggers
the flip done interrupt
Flip done handler is used to send the page flip event as soon as the
surface address is written as per the requirement of async flips.
The interrupt is disabled after the event is sent.
v2: -Change function name from icl_* to skl_* (Paulo)
-Move flip handler to this patch (Paulo)
-Remove vblank_put() (Paulo)
-Enable flip done interrupt for gen9+ only (Paulo)
-Enable flip done interrupt in power_well_post_enable hook (Paulo)
-Removed the event check in flip done handler to handle async
flips without pageflip events.
v3: -Move skl_disable_flip_done out of interrupt handler (Paulo)
-Make the pending vblank event NULL in the beginning of
flip_done_handler to remove sporadic WARN_ON that is seen.
v4: -Calculate timestamps using flip done time stamp and current
timestamp for async flips (Ville)
v5: -Fix the sparse warning by making the function 'g4x_get_flip_counter'
static.(Reported-by: kernel test robot <lkp@intel.com>)
-Fix the typo in commit message.
v6: -Revert back to old time stamping code.
-Remove the break while calling skl_enable_flip_done. (Paulo)
v7: -Rebased.
v8: -Rebased.
v9: -Use struct drm_i915_private *i915 in new code. (Ville)
-Use intel_crtc instead of drm_crtc. (Ville)
-Do not mix the flip done and vblank hooks. (Ville)
v10: -Rebased.
Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-2-karthik.b.s@intel.com
When validating a "YCbCr 4:2:0 only" mode we must take into
account the fact that we're going to be outputting YCbCr
4:2:0 or 4:4:4 (when a DP->HDMI protocol converter is doing
the 4:2:0 downsampling). For YCbCr 4:4:4 the minimum output
bpc is 8, for YCbCr 4:2:0 it'll be half that. The currently
hardcoded 6bpc is only correct for RGB 4:4:4, which we will
never use with these kinds of modes. Figure out what we're
going to output and use the correct min bpp value to validate
whether the link has sufficient bandwidth.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917214335.3569-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
As per the HDCP2.2 compliance test 1B-10 expectation, when stream
management for a repeater fails, we retry thrice and when it fails
in all retries, HDCP2.2 reauthentication aborted at kernel.
v2:
seq_num_m++ is extended for steam management failures too.[Anshuman]
v3:
use drm_dbg_kms instead of DRM_DEBUG_KMS [Anshuman]
v4:
dev_priv is used as i915 [JaniN]
v5:
Few improvisements are done [Sean]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923132435.17039-2-anshuman.gupta@intel.com
The name of the argument is different, causing those warnings:
./drivers/gpu/drm/drm_edid.c:3754: warning: Function parameter or member 'video_code' not described in 'drm_display_mode_from_cea_vic'
./drivers/gpu/drm/drm_edid.c:3754: warning: Excess function parameter 'vic' description in 'drm_display_mode_from_cea_vic'
Fixes: 7af655bce2 ("drm/dp: Add drm_dp_downstream_mode()")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200922175357.42998-3-lyude@redhat.com
As warned by kernel-doc:
./drivers/gpu/drm/drm_dp_helper.c:385: warning: Function parameter or member 'type' not described in 'drm_dp_downstream_is_type'
./drivers/gpu/drm/drm_dp_helper.c:886: warning: Function parameter or member 'dev' not described in 'drm_dp_downstream_mode'
Some function parameters weren't documented.
Fixes: 38784f6f88 ("drm/dp: Add helpers to identify downstream facing port types")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200922175357.42998-2-lyude@redhat.com
Just in case the caller passes in 0 for both slow&fast timeouts, make
sure we initialise the stack value returned. Add an assert so that we
don't make the mistake of passing 0 timeouts for the wait.
drivers/gpu/drm/i915/intel_uncore.c:2011 __intel_wait_for_register_fw() error: uninitialized symbol 'reg_value'.
References: 3f649ab728 ("treewide: Remove uninitialized_var() usage")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200916105022.28316-1-chris@chris-wilson.co.uk
Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.
v2: Put the check into the right place for CRT
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Having a mode where the display hardware is present but we try
to pretend it isn't just leads to massive headaches when trying
to reason what the fallout might be from skipping some random
bits of programming.
Let's just neuter INTEL_DISPLAY_ENABLED so that we treat the
hardware as fully present, except we just don't register any
outputs. That's still rather sketchy if the outputs are already
enabled when the driver is loaded. I think the simplest solution
would be to probe everything as normal and just return
disconnected" from all .detect() hooks. That would avoid anything
automagically enabling those outputs, but the driver could then
shut things down using the normal codepaths.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200909213824.12390-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
