The i.MX8QXP WCPU MEK board is a reworked version of the i.MX8QXP MEK
board, which includes some sensor and component changes. One of these
components is the WM8962 codec, which is meant to replace the WM8960
codec present on i.MX8QXP MEK. To avoid having to introduce a devicetree
overlay or another DTS, the WM8962 can be supported by using a virtual
I2C MUX since both of the codecs share the same I2C address.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to support Asynchronous Sample Rate Converter (ASRC), switch to
fsl-asoc-card driver for the wm8960 sound card.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fan controller on this board cannot work in automatic mode, and
requires software control, the reason is that it has no temperature
sensor connected.
Given that this board is a development kit and does not have any
specific fan, add a default single cooling level that would enable the
fan to spin with a 100% duty cycle, enabling a safe default.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The defaults for this SoC are configured for overdrive mode, but
the VPU clocks are currently configured for nominal mode.
Increase VPU_G1_CLK_ROOT to 800MHZ from 600MHz,
Increase VPU_G2_CLK_ROOT to 700MHZ from 500MHz, and
Increase VPU_BUS_CLK_ROOT to 800MHz from 600MHz.
This requires adjusting the clock parents. Since there is already
800MHz clock references, move the VPU_BUS and G1 clocks to it.
This frees up the VPU_PLL to be configured at 700MHz to run
the G2 clock at 700MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VPU_PLL clock must be set before the VPU_BUS clock which is derived
from the VPU_PLL clock else the VPU_BUS clock is 300MHz and not 600MHz.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPCv2 G1, G2 and VC8000E power-domain don't need to reference the
VPUMIX power-domain nor their module clocks since the power and reset
handling is done by the VPUMIX blkctrl driver.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
LGTM: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The iMX8QXP and iMX8QM have a CAAM (Cryptographic Acceleration and
Assurance Module) like many other iMXs.
Add the definitions for it.
Job Rings 0 and 1 are bound to the SECO (Security Controller) ARM core
and are not exposed outside it. There's no point to define them in the
bindings as they cannot be used outside the SECO.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the driving strength of all Ethernet RGMII R/TXC pads according to
hardware signal measurement result.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add usdhc3 and lpuart5 for imx93-9x9-qsb, imx93-11x11-evk and
imx93-14x14-evk, which connect to onboard wifi/bt module.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "eee-broken-1000t" was added on 8mm for FEC to avoid issue of ptp sync.
EQoS haven't such issue. So, remove this for EQoS phys.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX93 9x9 qsb has a ST LSM6DSO connected to I2C, which a is 6-axis
IMU (inertial measurement unit = accelerometer & gyroscope). So add the
missing parts to the DTS file.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the EQoS Ethernet controller on the i.MX8MP VAR-SOM with the
integrated Maxlinear MXL86110 PHY. The PHY is connected to the EQOS
MDIO bus at address 4.
This patch adds:
- EQOS controller configuration with RGMII interface.
- Proper reset timings.
- PHY power supply regulators.
- RGMII pinmux configuration for all data, control and clock signals.
- LED configuration for link status indication via the LED subsystem
under /sys/class/leds/, leveraging the support implemented in the.
mxl86110 PHY driver (drivers/net/phy/mxl-86110.c).
Two LEDs are defined to match the LED configuration on the Variscite
VAR-SOM Carrier Boards:
* LED@0: Yellow, netdev trigger.
* LED@1: Green, netdev trigger.
The RGMII TX/RX delays are implemented in SOM via PCB passive
delays, so no software delay configuration is required.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver strength is too high for SDR104 mode. Change the driver strength
to x3 according to hardware recommendation.
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB3 PHY tuning properties for imx95-15x15-evk and imx95-19x19-evk
boards according to signal measurement results.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add adc0 flexcan[1,2] i2c[2,3] uart5 spi3 tpm3 netc_timer and related phys
regulators pinmux and related child nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Variscite has updated the Ethernet PHY on the VAR-SOM-MX93 from the
ADIN1300BCPZ to the MaxLinear MXL86110, as documented in the
August 2023 revision changelog.
Link: https://variwiki.com/index.php?title=VAR-SOM-MX93_rev_changelog
Update the device tree accordingly:
- Drop the regulator node used to power the previously PHY.
- Add support for the reset line using GPIO1_IO07 with proper timings.
- Configure the PHY LEDs via the LED subsystem under /sys/class/leds/,
leveraging the support implemented in the mxl86110 PHY driver
(drivers/net/phy/mxl-86110.c).
Two LEDs are defined to match the LED configuration on the Variscite
VAR-SOM Carrier Boards:
* LED@0: Yellow, netdev trigger.
* LED@1: Green, netdev trigger.
- Adjust the RGMII clock pad control settings to match the updated PHY
requirements.
These changes ensure proper PHY initialization and LED status indication
for the new MaxLinear MXL86110, improving board compatibility with the
latest hardware revision.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW74xx D revision has added a M2SKT_WDIS2# GPIO which routes to the
W_DISABLE2# pin of the M.2 socket. Update the gpio name for consistency.
Fixes: 6a5d95b06d ("arm64: dts: imx8mp-venice-gw74xx: add M2SKT_GPIO10 gpio configuration")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move configuration for ADC voltage reference from board DTS to a SoM
include file. The SoC ADC reference voltage is connected to a "VDDA_1V8"
voltage node and supplied by the PMIC's BUCK5 regulator. The reference
voltage is thus defined by the SoM and cannot be changed by the carrier
board design and as such belongs into the SoM include file.
Moreover, with this in place, customers designing own carrier boards can
simply include imx93-phycore-som.dtsi and enable adc1 in their own DTS
without the need to define dummy ADC vref regulator themselves anymore.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM microphone and convert
the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set ethernet1 alias to EQOS interface on phyBOARD-Segin-i.MX93 marking
it the secondary networking interface. The primary ethernet0 interface
is already set by the SoM include file (imx93-phycore-som.dtsi).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move alias for ethernet0 interface to the phyCORE-i.MX93 SoM include
file. The reason behind it is that the physical location of the PHY chip
connected to FEC interface is on the SoM itself and alias thus belongs
into the SoM device-tree. Consequently, it can be used by all boards
based on the phyCORE-i.MX93 SoM (phyBOARD-Segin and phyBOARD-Nash).
This also enables us to mark FEC interface as the primary / first for
networking in the bootloader and systemd (predictable interface names).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the BOE av123z7m-n17 variant of the Moduline Display, this variant
comes with a 12.3" 1920x720 display.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the BOE av101hdt-a10 variant of the Moduline Display, this variant
comes with a 10.1 1280x720 display with a touchscreen (not working in
mainline).
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Moduline Display platform is a part of the wider GOcontroll Moduline
ecosystem. These are embedded controllers that focus on modularity with
their swappable IO modules.
The base Moduline Display board includes a board-to-board connector with
various busses to enable adding new display types required by the
application. It includes 2 Moduline IO module slots, a simple mono
codec/amplifier, a four channel adc, 2 CAN busses, an RTC and optional
wifi/bluetooth.
busses to the display adapter include:
- 4 lane LVDS
- 4 lane MIPI-DSI
- 4 lane MIPI-CSI
- HDMI 2.0a
- USB 2.0
- I2S
- I2C
- SPI
Also a couple of GPIO and PWM pins for controlling various ICs on the
display adapter board.
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ka-Ro Electronics tx8p-ml81 is a COM based on the imx8mp SOC. It has
2 GB of ram and 8 GB of eMMC storage on board.
Add it to enable boards based on this Module
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently to configure each IOMUXC_SW_PAD_CTL_PAD the raw value of this
register is written in the dts, these values are not obvious. Add defines
which describe the fields of this register which can be or-ed together to
produce readable settings.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit da5dd31efd ("gpio: vf610: Switch to gpio-mmio"),
the vf610 GPIO driver no longer uses the static number 32 for
gc->ngpio. This allows users to configure the number of GPIOs
per port.
And some gpio controllers did have less pads. So add 'ngpios' here,
this can save some memory when request bitmap, and also show user
more accurate information when use gpio tools.
Besides, some gpio controllers have hole in the gpio ranges, so use
'gpio-reserved-ranges' to cover that, then the gpioinfo tool show the
correct result.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Starting with commit e6ef4f8ede ("gpio: vf610: make irq_chip immutable")
gpio-vf610 supports locking GPIO being used for IRQ. This already prevents
configuring the GPIO as output, so there is no need for a GPIO hog.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa9352 is only using LPDDR4X, so the BUCK2 regulator should be fixed
at 600MV.
Fixes: d2858e6bd3 ("arm64: dts: freescale: imx93-tqma9352: Add PMIC node")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hook up the gpu as a passive cooling device to the thermal zones' alert
trip point just like the cpu.
The gpu here consists of 3D GPU, 2D GPU and NPU.
One way to test would be to set one "alert" trip point low enough
and watch the cooling device state increase:
echo 10000 > /sys/class/thermal/thermal_zone0/trip_point_0_temp
watch cat /sys/class/thermal/cooling_device*/cur_state
And of course set the trip point back to its original value and watch
the cooling device states jump to 0 again.
Signed-off-by: Martin Kepplinger-Novaković <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I.MX95 I3C only need two clocks so add clock fix. Add "nxp,imx95-i3c"
compatible string for all imx95 i3c nodes.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
