Pull timer fixes from Thomas Gleixner:
"Two fixes in the timer area:
- a long-standing lock inversion due to a printk
- suspend-related hrtimer corruption in sched_clock"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timer: Fix lock inversion between hrtimer_bases.lock and scheduler locks
sched_clock: Avoid corrupting hrtimer tree during suspend
Pull ARM fixes from Russell King:
"A few fixes for ARM. Some of these are correctness issues:
- TLBs must be flushed after the old mappings are removed by the DMA
mapping code, but before the new mappings are established.
- An off-by-one entry error in the Keystone LPAE setup code.
Fixes include:
- ensuring that the identity mapping for LPAE does not remove the
kernel image from the identity map.
- preventing userspace from trapping into kgdb.
- fixing a preemption issue in the Intel iwmmxt code.
- fixing a build error with nommu.
Other changes include:
- Adding a note about which areas of memory are expected to be
accessible while the identity mapping tables are in place"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8124/1: don't enter kgdb when userspace executes a kgdb break instruction
ARM: idmap: add identity mapping usage note
ARM: 8115/1: LPAE: reduce damage caused by idmap to virtual memory layout
ARM: fix alignment of keystone page table fixup
ARM: 8112/1: only select ARM_PATCH_PHYS_VIRT if MMU is enabled
ARM: 8100/1: Fix preemption disable in iwmmxt_task_enable()
ARM: DMA: ensure that old section mappings are flushed from the TLB
The kgdb breakpoint hooks (kgdb_brk_fn and kgdb_compiled_brk_fn)
should only be entered when a kgdb break instruction is executed
from the kernel. Otherwise, if kgdb is enabled, a userspace program
can cause the kernel to drop into the debugger by executing either
KGDB_BREAKINST or KGDB_COMPILED_BREAK.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a note about the usage of the identity mapping; we do not support
accesses outside of the identity map region and kernel image while a
CPU is using the identity map. This is because the identity mapping
may overwrite vmalloc space, IO mappings, the vectors pages, etc.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull vfs fixes from Al Viro:
"This contains a couple of fixes - one is the aio fix from Christoph,
the other a fallocate() one from Eric"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: fix check for fallocate on active swapfile
direct-io: fix AIO regression
Pull x86 fix from Peter Anvin:
"A single fix to not invoke the espfix code on Xen PV, as it turns out
to oops the guest when invoked after all. This patch leaves some
amount of dead code, in particular unnecessary initialization of the
espfix stacks when they won't be used, but in the interest of keeping
the patch minimal that cleanup can wait for the next cycle"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64/entry/xen: Do not invoke espfix64 on Xen
Pull staging driver bugfixes from Greg KH:
"Here are some tiny staging driver bugfixes that I've had in my tree
for the past week that resolve some reported issues. Nothing major at
all, but it would be good to get them merged for 3.16-rc8 or -final"
* tag 'staging-3.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: Fix disassociated messages every 10 seconds
staging: vt6655: Fix Warning on boot handle_irq_event_percpu.
staging: rtl8723au: rtw_resume(): release semaphore before exit on error
iio:bma180: Missing check for frequency fractional part
iio:bma180: Fix scale factors to report correct acceleration units
iio: buffer: Fix demux table creation
Pull device mapper fixes from Mike Snitzer:
"Fix dm bufio shrinker to properly zero-fill all fields.
Fix race in dm cache that caused improper reporting of the number of
dirty blocks in the cache"
* tag 'dm-3.16-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix race affecting dirty block count
dm bufio: fully initialize shrinker
Pull ARM straggler SoC fix from Olof Johansson:
"A DT bugfix for Nomadik that had an ambigouos double-inversion of a
gpio line, and one MAINTAINER URL update that might as well go in now.
We could hold off until the merge window, but then we'll just have to
mark the DT fix for stable and it just seems like in total causing
more work"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Update Tegra Git URL
ARM: nomadik: fix up double inversion in DT
nr_dirty is updated without locking, causing it to drift so that it is
non-zero (either a small positive integer, or a very large one when an
underflow occurs) even when there are no actual dirty blocks. This was
due to a race between the workqueue and map function accessing nr_dirty
in parallel without proper protection.
People were seeing under runs due to a race on increment/decrement of
nr_dirty, see: https://lkml.org/lkml/2014/6/3/648
Fix this by using an atomic_t for nr_dirty.
Reported-by: roma1390@gmail.com
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
1d3d4437ea ("vmscan: per-node deferred work") added a flags field to
struct shrinker assuming that all shrinkers were zero filled. The dm
bufio shrinker is not zero filled, which leaves arbitrary kmalloc() data
in flags. So far the only defined flags bit is SHRINKER_NUMA_AWARE.
But there are proposed patches which add other bits to shrinker.flags
(e.g. memcg awareness).
Rather than simply initializing the shrinker, this patch uses kzalloc()
when allocating the dm_bufio_client to ensure that the embedded shrinker
and any other similar structures are zeroed.
This fixes theoretical over aggressive shrinking of dm bufio objects.
If the uninitialized dm_bufio_client.shrinker.flags contains
SHRINKER_NUMA_AWARE then shrink_slab() would call the dm shrinker for
each numa node rather than just once. This has been broken since 3.12.
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.12+
Fix the broken check for calling sys_fallocate() on an active swapfile,
introduced by commit 0790b31b69 ("fs: disallow all fallocate
operation on active swapfile").
Signed-off-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The direct-io.c rewrite to use the iov_iter infrastructure stopped updating
the size field in struct dio_submit, and thus rendered the check for
allowing asynchronous completions to always return false. Fix this by
comparing it to the count of bytes in the iov_iter instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Pull ACPI fix from Rafael Wysocki:
"One commit that fixes a problem causing PNP devices to be associated
with wrong ACPI device objects sometimes during device enumeration due
to an incorrect check in a matching function.
That problem was uncovered by the ACPI device enumeration rework in
3.14"
* tag 'pm+acpi-3.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: Fix acpi_pnp_match()
Pull clock driver fix from Mike Turquette:
"A single patch to re-enable audio which is broken on all DRA7
SoC-based platforms. Missed this one from the last set of fixes"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: ti: clk-7xx: Correct ABE DPLL configuration
Pull crypto fix from Herbert Xu:
"This adds missing SELinux labeling to AF_ALG sockets which apparently
causes SELinux (or at least the SELinux people) to misbehave :)"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: af_alg - properly label AF_ALG socket
Pull SCSI barrier fix from James Bottomley:
"This is a potential data corruption fix: If we get an error sending
down a barrier, we simply ignore it meaning the barrier semantics get
violated without anyone being any the wiser. If the system crashes at
this point, the filesystem potentially becomes corrupt. Fix is to
report errors on failed barriers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: handle flush errors properly
ABE DPLL frequency need to be lowered from 361267200
to 180633600 to facilitate the ATL requironments.
The dpll_abe_m2x2_ck clock need to be set to double
of ABE DPLL rate in order to have correct clocks
for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
free_huge_page() is undefined without CONFIG_HUGETLBFS and there's no
need to filter PageHuge() page is such a configuration either, so avoid
exporting the symbol to fix a build error:
In file included from kernel/kexec.c:14:0:
kernel/kexec.c: In function 'crash_save_vmcoreinfo_init':
kernel/kexec.c:1623:20: error: 'free_huge_page' undeclared (first use in this function)
VMCOREINFO_SYMBOL(free_huge_page);
^
Introduced by commit 8f1d26d0e5 ("kexec: export free_huge_page to
VMCOREINFO")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
Josh has moved
kexec: export free_huge_page to VMCOREINFO
mm: fix filemap.c pagecache_get_page() kernel-doc warnings
mm: debugfs: move rounddown_pow_of_two() out from do_fault path
memcg: oom_notify use-after-free fix
hwpoison: call action_result() in failure path of hwpoison_user_mappings()
hwpoison: fix hugetlbfs/thp precheck in hwpoison_user_mappings()
rapidio/tsi721_dma: fix failure to obtain transaction descriptor
mm, thp: do not allow thp faults to avoid cpuset restrictions
mm/page-writeback.c: fix divide by zero in bdi_dirty_limits()
My IBM email addresses haven't worked for years; also map some
old-but-functional forwarding addresses to my canonical address.
Update my GPG key fingerprint; I moved to 4096R a long time ago.
Update description.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PG_head_mask was added into VMCOREINFO to filter huge pages in b3acc56bfe
("kexec: save PG_head_mask in VMCOREINFO"), but makedumpfile still need
another symbol to filter *hugetlbfs* pages.
If a user hope to filter user pages, makedumpfile tries to exclude them by
checking the condition whether the page is anonymous, but hugetlbfs pages
aren't anonymous while they also be user pages.
We know it's possible to detect them in the same way as PageHuge(),
so we need the start address of free_huge_page():
int PageHuge(struct page *page)
{
if (!PageCompound(page))
return 0;
page = compound_head(page);
return get_compound_page_dtor(page) == free_huge_page;
}
For that reason, this patch changes free_huge_page() into public
to export it to VMCOREINFO.
Signed-off-by: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-doc warnings in mm/filemap.c: pagecache_get_page():
Warning(..//mm/filemap.c:1054): No description found for parameter 'cache_gfp_mask'
Warning(..//mm/filemap.c:1054): No description found for parameter 'radix_gfp_mask'
Warning(..//mm/filemap.c:1054): Excess function parameter 'gfp_mask' description in 'pagecache_get_page'
Fixes: 2457aec637 ("mm: non-atomically mark page accessed during page cache allocation where possible")
[mgorman@suse.de: change everything]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_fault_around() expects fault_around_bytes rounded down to nearest page
order. Instead of calling rounddown_pow_of_two every time in
fault_around_pages()/fault_around_mask() we could do round down when user
changes fault_around_bytes via debugfs interface.
This also fixes bug when user set fault_around_bytes to 0. Result of
rounddown_pow_of_two(0) is not defined, therefore fault_around_bytes == 0
doesn't work without this patch.
Let's set fault_around_bytes to PAGE_SIZE if user sets to something less
than PAGE_SIZE
[akpm@linux-foundation.org: tweak code layout]
Fixes: a9b0f861("mm: nominate faultaround area in bytes rather than page order")
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> [3.15.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hwpoison_user_mappings() could fail for various reasons, so printk()s to
print out the reasons should be done in each failure check inside
hwpoison_user_mappings().
And currently we don't call action_result() when hwpoison_user_mappings()
fails, which is not consistent with other exit points of memory error
handler. So this patch fixes these messaging problems.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A recent fix from Chen Yucong, commit 0bc1f8b068 ("hwpoison: fix the
handling path of the victimized page frame that belong to non-LRU")
rejects going into unmapping operation for hugetlbfs/thp pages, which
results in failing error containing on such pages. This patch fixes it.
With this patch, hwpoison functional tests in mce-test testsuite pass.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swarren/linux-tegra.git is a stale location; it has moved to
tegra/linux.git.
While the git protocol re-directs to the new location, HTTP does not.
Besides, MAINTAINERS should contain the canonical URL.
Signed-off-by: Andreas Färber <afaerber@suse.de>
[swarren, updated commit message]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).
After commit 78f87df2b4
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.
So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull Exynos platform DT fix from Grant Likely:
"Device tree Exynos bug fix for v3.16-rc7
This bug fix has been brewing for a while. I hate sending it to you
so late, but I only got confirmation that it solves the problem this
past weekend. The diff looks big for a bug fix, but the majority of
it is only executed in the Exynos quirk case. Unfortunately it
required splitting early_init_dt_scan() in two and adding quirk
handling in the middle of it on ARM.
Exynos has buggy firmware that puts bad data into the memory node.
Commit 1c2f87c225 ("ARM: Get rid of meminfo") exposed the bug by
dropping the artificial upper bound on the number of memory banks that
can be added. Exynos fails to boot after that commit. This branch
fixes it by splitting the early DT parse function and inserting a
fixup hook. Exynos uses the hook to correct the DT before parsing
memory regions"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
arm: Add devicetree fixup machine function
of: Add memory limiting function for flattened devicetrees
of: Split early_init_dt_scan into two parts
Pull Xen fix from David Vrabel:
"Fix BUG when trying to expand the grant table. This seems to occur
often during boot with Ubuntu 14.04 PV guests"
* tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: safely map and unmap grant frames when in atomic context
Pull KVM fix from Paolo Bonzini:
"Fix a bug which allows KVM guests to bring down the entire system on
some 64K enabled ARM64 hosts"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: arm64: vgic: fix hyp panic with 64k pages on juno platform
This reverts commit 20fbe3ae99.
As reported by Stephen Rothwell, it causes compile failures in certain
configurations:
drivers/net/usb/cdc_subset.c:360:15: error: 'dummy_prereset' undeclared here (not in a function)
.pre_reset = dummy_prereset,
^
drivers/net/usb/cdc_subset.c:361:16: error: 'dummy_postreset' undeclared here (not in a function)
.post_reset = dummy_postreset,
^
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David Miller <davem@davemloft.net>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Make fragmentation IDs less predictable, from Eric Dumazet.
2) TSO tunneling can crash in bnx2x driver, fix from Dmitry Kravkov.
3) Don't allow NULL msg->msg_name just because msg->msg_namelen is
non-zero, from Andrey Ryabinin.
4) ndm->ndm_type set using wrong macros, from Jun Zhao.
5) cdc-ether devices can come up with entries in their address filter,
so explicitly clear the filter after the device initializes. From
Oliver Neukum.
6) Forgotten refcount bump in xfrm_lookup(), from Steffen Klassert.
7) Short packets not padded properly, exposing random data, in bcmgenet
driver. Fix from Florian Fainelli.
8) xgbe_probe() doesn't return an error code, but rather zero, when
netif_set_real_num_tx_queues() fails. Fix from Wei Yongjun.
9) USB speed not probed properly in r8152 driver, from Hayes Wang.
10) Transmit logic choosing the outgoing port in the sunvnet driver
needs to consider a) is the port actually up and b) whether it is a
switch port. Fix from David L Stevens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net: phy: re-apply PHY fixups during phy_register_device
cdc-ether: clean packet filter upon probe
cdc_subset: deal with a device that needs reset for timeout
net: sendmsg: fix NULL pointer dereference
isdn/bas_gigaset: fix a leak on failure path in gigaset_probe()
ip: make IP identifiers less predictable
neighbour : fix ndm_type type error issue
sunvnet: only use connected ports when sending
can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()
bnx2x: fix crash during TSO tunneling
r8152: fix the checking of the usb speed
net: phy: Ensure the MDIO bus module is held
net: phy: Set the driver when registering an MDIO bus device
bnx2x: fix set_setting for some PHYs
hyperv: Fix error return code in netvsc_init_buf()
amd-xgbe: Fix error return code in xgbe_probe()
ath9k: fix aggregation session lockup
net: bcmgenet: correctly pad short packets
net: sctp: inherit auth_capable on INIT collisions
mac80211: fix crash on getting sta info with uninitialized rate control
...
arch_gnttab_map_frames() and arch_gnttab_unmap_frames() are called in
atomic context but were calling alloc_vm_area() which might sleep.
Also, if a driver attempts to allocate a grant ref from an interrupt
and the table needs expanding, then the CPU may already by in lazy MMU
mode and apply_to_page_range() will BUG when it tries to re-enable
lazy MMU mode.
These two functions are only used in PV guests.
Introduce arch_gnttab_init() to allocates the virtual address space in
advance.
Avoid the use of apply_to_page_range() by using saving and using the
array of PTE addresses from the alloc_vm_area() call (which ensures
that the required page tables are pre-allocated).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the physical address of GICV isn't page-aligned, then we end up
creating a stage-2 mapping of the page containing it, which causes us to
map neighbouring memory locations directly into the guest.
As an example, consider a platform with GICV at physical 0x2c02f000
running a 64k-page host kernel. If qemu maps this into the guest at
0x80010000, then guest physical addresses 0x80010000 - 0x8001efff will
map host physical region 0x2c020000 - 0x2c02efff. Accesses to these
physical regions may cause UNPREDICTABLE behaviour, for example, on the
Juno platform this will cause an SError exception to EL3, which brings
down the entire physical CPU resulting in RCU stalls / HYP panics / host
crashing / wasted weeks of debugging.
SBSA recommends that systems alias the 4k GICV across the bounding 64k
region, in which case GICV physical could be described as 0x2c020000 in
the above scenario.
This patch fixes the problem by failing the vgic probe if the physical
base address or the size of GICV aren't page-aligned. Note that this
generated a warning in dmesg about freeing enabled IRQs, so I had to
move the IRQ enabling later in the probe.
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Joel Schopp <joel.schopp@amd.com>
Cc: Don Dutile <ddutile@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Joel Schopp <joel.schopp@amd.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Commit 1c2f87c225
(ARM: 8025/1: Get rid of meminfo) dropped the upper bound on
the number of memory banks that can be added as there was no
technical need in the kernel. It turns out though, some bootloaders
(specifically the arndale-octa exynos boards) may pass invalid memory
information and rely on the kernel to not parse this data. This is a
bug in the bootloader but we still need to work around this.
Work around this by introducing a dt_fixup function. This function
gets called before the flattened devicetree is scanned for memory
and the like. In this fixup function for exynos, limit the maximum
number of memory regions in the devicetree.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Andreas Färber <afaerber@suse.de>
[glikely: Added a comment and fixed up function name]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Buggy bootloaders may pass bogus memory entries in the devicetree.
Add of_fdt_limit_memory to add an upper bound on the number of
entries that can be present in the devicetree.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Currently, early_init_dt_scan validates the header, sets the
boot params, and scans for chosen/memory all in one function.
Split this up into two separate functions (validation/setting
boot params in one, scanning in another) to allow for
additional setup between boot params and scanning the memory.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Andreas Färber <afaerber@suse.de>
[glikely: s/early_init_dt_scan_all/early_init_dt_scan_nodes/]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The acpi_pnp_match() function is used for finding the ACPI device
object that should be associated with the given PNP device.
Unfortunately, the check used by that function is not strict enough
and may cause success to be returned for a wrong ACPI device object.
To fix that, use the observation that the pointer to the ACPI
device object in question is already stored in the data field
in struct pnp_dev, so acpi_pnp_match() can simply use that
field to do its job.
This problem was uncovered in 3.14 by commit 202317a573 (ACPI / scan:
Add acpi_device objects for all device nodes in the namespace).
Fixes: 202317a573 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Reported-and-tested-by: Vinson Lee <vlee@twopensource.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
moved the call to phy_scan_fixups() in phy_init_hw() after a software
reset is performed.
By the time phy_init_hw() is called in phy_device_register(), no driver
has been bound to this PHY yet, so all the checks in phy_init_hw()
against the PHY driver and the PHY driver's config_init function will
return 0. We will therefore never call phy_scan_fixups() as we should.
Fix this by calling phy_scan_fixups() and check for its return value to
restore the intended functionality.
This broke PHY drivers which do register an early PHY fixup callback to
intercept the PHY probing and do things like changing the 32-bits unique
PHY identifier when a pseudo-PHY address has been used, as well as
board-specific PHY fixups that need to be applied during driver probe
time.
Reported-by: Hauke Merthens <hauke-m@hauke-m.de>
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are devices that don't do reset all the way. So the packet filter should
be set to a sane initial value. Failure to do so leads to intermittent failures
of DHCP on some systems under some conditions.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device needs to be reset to recover from a timeout.
Unfortunately this can be handled only at the level of
the subdrivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha's report:
> While fuzzing with trinity inside a KVM tools guest running the latest -next
> kernel with the KASAN patchset, I've stumbled on the following spew:
>
> [ 4448.949424] ==================================================================
> [ 4448.951737] AddressSanitizer: user-memory-access on address 0
> [ 4448.952988] Read of size 2 by thread T19638:
> [ 4448.954510] CPU: 28 PID: 19638 Comm: trinity-c76 Not tainted 3.16.0-rc4-next-20140711-sasha-00046-g07d3099-dirty #813
> [ 4448.956823] ffff88046d86ca40 0000000000000000 ffff880082f37e78 ffff880082f37a40
> [ 4448.958233] ffffffffb6e47068 ffff880082f37a68 ffff880082f37a58 ffffffffb242708d
> [ 4448.959552] 0000000000000000 ffff880082f37a88 ffffffffb24255b1 0000000000000000
> [ 4448.961266] Call Trace:
> [ 4448.963158] dump_stack (lib/dump_stack.c:52)
> [ 4448.964244] kasan_report_user_access (mm/kasan/report.c:184)
> [ 4448.965507] __asan_load2 (mm/kasan/kasan.c:352)
> [ 4448.966482] ? netlink_sendmsg (net/netlink/af_netlink.c:2339)
> [ 4448.967541] netlink_sendmsg (net/netlink/af_netlink.c:2339)
> [ 4448.968537] ? get_parent_ip (kernel/sched/core.c:2555)
> [ 4448.970103] sock_sendmsg (net/socket.c:654)
> [ 4448.971584] ? might_fault (mm/memory.c:3741)
> [ 4448.972526] ? might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3740)
> [ 4448.973596] ? verify_iovec (net/core/iovec.c:64)
> [ 4448.974522] ___sys_sendmsg (net/socket.c:2096)
> [ 4448.975797] ? put_lock_stats.isra.13 (./arch/x86/include/asm/preempt.h:98 kernel/locking/lockdep.c:254)
> [ 4448.977030] ? lock_release_holdtime (kernel/locking/lockdep.c:273)
> [ 4448.978197] ? lock_release_non_nested (kernel/locking/lockdep.c:3434 (discriminator 1))
> [ 4448.979346] ? check_chain_key (kernel/locking/lockdep.c:2188)
> [ 4448.980535] __sys_sendmmsg (net/socket.c:2181)
> [ 4448.981592] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2600)
> [ 4448.982773] ? trace_hardirqs_on (kernel/locking/lockdep.c:2607)
> [ 4448.984458] ? syscall_trace_enter (arch/x86/kernel/ptrace.c:1500 (discriminator 2))
> [ 4448.985621] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2600)
> [ 4448.986754] SyS_sendmmsg (net/socket.c:2201)
> [ 4448.987708] tracesys (arch/x86/kernel/entry_64.S:542)
> [ 4448.988929] ==================================================================
This reports means that we've come to netlink_sendmsg() with msg->msg_name == NULL and msg->msg_namelen > 0.
After this report there was no usual "Unable to handle kernel NULL pointer dereference"
and this gave me a clue that address 0 is mapped and contains valid socket address structure in it.
This bug was introduced in f3d3342602
(net: rework recvmsg handler msg_name and msg_namelen logic).
Commit message states that:
"Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address."
But in fact this affects sendto when address 0 is mapped and contains
socket address structure in it. In such case copy-in address will succeed,
verify_iovec() function will successfully exit with msg->msg_namelen > 0
and msg->msg_name == NULL.
This patch fixes it by setting msg_namelen to 0 if msg_name == NULL.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: <stable@vger.kernel.org>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a lack of usb_put_dev(udev) on failure path in gigaset_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM SoC fixes from Arnd Bergmann:
"A nice small set of bug fixes for arm-soc:
- two incorrect register addresses in DT files on shmobile and hisilicon
- one revert for a regression on omap
- one bug fix for a newly introduced pin controller binding
- one regression fix for the memory controller on omap
- one patch to avoid a harmless WARN_ON"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: Revert enabling of twl configuration for n900
ARM: dts: fix L2 address in Hi3620
ARM: OMAP2+: gpmc: fix gpmc_hwecc_bch_capable()
pinctrl: dra: dt-bindings: Fix pull enable/disable
ARM: shmobile: r8a7791: Fix SD2CKCR register address
ARM: OMAP2+: l2c: squelch warning dump on power control setting
Correctly assemble the client UUID by OR'ing in the flags rather than
assigning them over the other components.
Reported-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-doc warnings and function name in mm/page_alloc.c:
Warning(..//mm/page_alloc.c:6074): No description found for parameter 'pfn'
Warning(..//mm/page_alloc.c:6074): No description found for parameter 'mask'
Warning(..//mm/page_alloc.c:6074): Excess function parameter 'start_bitidx' description in 'get_pfnblock_flags_mask'
Warning(..//mm/page_alloc.c:6102): No description found for parameter 'pfn'
Warning(..//mm/page_alloc.c:6102): No description found for parameter 'mask'
Warning(..//mm/page_alloc.c:6102): Excess function parameter 'start_bitidx' description in 'set_pfnblock_flags_mask'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On LPAE, each level 1 (pgd) page table entry maps 1GiB, and the level 2
(pmd) entries map 2MiB.
When the identity mapping is created on LPAE, the pgd pointers are copied
from the swapper_pg_dir. If we find that we need to modify the contents
of a pmd, we allocate a new empty pmd table and insert it into the
appropriate 1GB slot, before then filling it with the identity mapping.
However, if the 1GB slot covers the kernel lowmem mappings, we obliterate
those mappings.
When replacing a PMD, first copy the old PMD contents to the new PMD, so
that we preserve the existing mappings, particularly the mappings of the
kernel itself.
[rewrote commit message and added code comment -- rmk]
Fixes: ae2de10173 ("ARM: LPAE: Add identity mapping support for the 3-level page table format")
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge "omap n900 regression fix for v3.16 rc series" from Tony Lindgren:
Minimal regression fix for n900 display that got broken with
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
* tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert enabling of twl configuration for n900
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If init_mm.brk is not section aligned, the LPAE fixup code will miss
updating the final PMD. Fix this by aligning map_end.
Fixes: a77e0c7b27 ("ARM: mm: Recreate kernel mappings in early_paging_init()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.
Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: Tony Lindgren <tony@atomide.com>
In "Counting Packets Sent Between Arbitrary Internet Hosts", Jeffrey and
Jedidiah describe ways exploiting linux IP identifier generation to
infer whether two machines are exchanging packets.
With commit 73f156a6e8 ("inetpeer: get rid of ip_id_count"), we
changed IP id generation, but this does not really prevent this
side-channel technique.
This patch adds a random amount of perturbation so that IP identifiers
for a given destination [1] are no longer monotonically increasing after
an idle period.
Note that prandom_u32_max(1) returns 0, so if generator is used at most
once per jiffy, this patch inserts no hole in the ID suite and do not
increase collision probability.
This is jiffies based, so in the worst case (HZ=1000), the id can
rollover after ~65 seconds of idle time, which should be fine.
We also change the hash used in __ip_select_ident() to not only hash
on daddr, but also saddr and protocol, so that ICMP probes can not be
used to infer information for other protocols.
For IPv6, adds saddr into the hash as well, but not nexthdr.
If I ping the patched target, we can see ID are now hard to predict.
21:57:11.008086 IP (...)
A > target: ICMP echo request, seq 1, length 64
21:57:11.010752 IP (... id 2081 ...)
target > A: ICMP echo reply, seq 1, length 64
21:57:12.013133 IP (...)
A > target: ICMP echo request, seq 2, length 64
21:57:12.015737 IP (... id 3039 ...)
target > A: ICMP echo reply, seq 2, length 64
21:57:13.016580 IP (...)
A > target: ICMP echo request, seq 3, length 64
21:57:13.019251 IP (... id 3437 ...)
target > A: ICMP echo reply, seq 3, length 64
[1] TCP sessions uses a per flow ID generator not changed by this patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jeffrey Knockel <jeffk@cs.unm.edu>
Reported-by: Jedidiah R. Crandall <crandall@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndm_type means L3 address type, in neighbour proxy and vxlan, it's RTN_UNICAST.
NDA_DST is for netlink TLV type, hence it's not right value in this context.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunvnet driver doesn't check whether or not a port is connected when
transmitting packets, which results in failures if a port fails to connect
(e.g., due to a version mismatch). The original code also assumes
unnecessarily that the first port is up and a switch, even though there is
a flag for switch ports.
This patch only matches a port if it is connected, and otherwise uses the
switch_port flag to send the packet to a switch port that is up.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can 2014-07-25
this is a pull request of one patch for the net tree, hoping to get into the
3.16 release.
The patch by George Cherian fixes a regression in the c_can platform driver.
When using two interfaces the regression leads to a non function second
interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the espfix64 logic into native_iret. To make this work,
it gets rid of the native patch for INTERRUPT_RETURN:
INTERRUPT_RETURN on native kernels is now 'jmp native_iret'.
This changes the 16-bit SS behavior on Xen from OOPSing to leaking
some bits of the Xen hypervisor's RSP (I think).
[ hpa: this is a nonzero cost on native, but probably not enough to
measure. Xen needs to fix this in their own code, probably doing
something equivalent to espfix64. ]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/7b8f1d8ef6597cb16ae004a43c56980a7de3cf94.1406129132.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Pull ARM AES crypto fixes from Herbert Xu:
"This push fixes a regression on ARM where odd-sized blocks supplied to
AES may cause crashes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm-aes - fix encryption of unaligned data
crypto: arm64-aes - fix encryption of unaligned data
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 more small powerpc fixes that should still go into .16.
One is a recent regression (MMCR2 business), the other is a trivial
endian fix without which FW updates won't work on LE in IBM machines,
and the 3rd one turns a BUG_ON into a WARN_ON which is definitely a
LOT more friendly especially when the whole thing is about retrieving
error logs ..."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix endianness of flash_block_list in rtas_flash
powerpc/powernv: Change BUG_ON to WARN_ON in elog code
powerpc/perf: Fix MMCR2 handling for EBB
cryptsetup fails on arm64 when using kernel encryption via AF_ALG socket.
See https://bugzilla.redhat.com/show_bug.cgi?id=1122937
The bug is caused by incorrect handling of unaligned data in
arch/arm64/crypto/aes-glue.c. Cryptsetup creates a buffer that is aligned
on 8 bytes, but not on 16 bytes. It opens AF_ALG socket and uses the
socket to encrypt data in the buffer. The arm64 crypto accelerator causes
data corruption or crashes in the scatterwalk_pagedone.
This patch fixes the bug by passing the residue bytes that were not
processed as the last parameter to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function rtas_flash_firmware passes the address of a data structure,
flash_block_list, when making the update-flash-64-and-reboot rtas call.
While the endianness of the address is handled correctly, the endianness
of the data is not. This patch ensures that the data in flash_block_list
is big endian when passed to rtas on little endian hosts.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull perf fixes from Thomas Gleixner:
"A bunch of fixes for perf and kprobes:
- revert a commit that caused a perf group regression
- silence dmesg spam
- fix kprobe probing errors on ia64 and ppc64
- filter kprobe faults from userspace
- lockdep fix for perf exit path
- prevent perf #GP in KVM guest
- correct perf event and filters"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Fix "Failed to find blacklist" probing errors on ia64 and ppc64
kprobes/x86: Don't try to resolve kprobe faults from userspace
perf/x86/intel: Avoid spamming kernel log for BTS buffer failure
perf/x86/intel: Protect LBR and extra_regs against KVM lying
perf: Fix lockdep warning on process exit
perf/x86/intel/uncore: Fix SNB-EP/IVT Cbox filter mappings
perf/x86/intel: Use proper dTLB-load-misses event on IvyBridge
perf: Revert ("perf: Always destroy groups on exit")
Pull x86 fixes from Peter Anvin:
"A couple of crash fixes, plus a fix that on 32 bits would cause a
missing -ENOSYS for nonexistent system calls"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Fix cache topology for early P4-SMT
x86_32, entry: Store badsys error code in %eax
x86, MCE: Robustify mcheck_init_device
Pull vfs fixes from Christoph Hellwig:
"A vfsmount leak fix, and a compile warning fix"
* 'vfs-for-3.16' of git://git.infradead.org/users/hch/vfs:
fs: umount on symlink leaks mnt count
direct-io: fix uninitialized warning in do_direct_IO()
Pull firewire regression fix from Stefan Richter:
"IEEE 1394 (FireWire) subsystem fix: MSI don't work on VIA PCIe
controllers with some isochronous workloads (regression since
v3.16-rc1)"
* tag 'firewire-fix-vt6315' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: disable MSI for VIA VT6315 again
Michel Dänzer and a couple of other people reported inexplicable random
oopses in the scheduler, and the cause turns out to be gcc mis-compiling
the load_balance() function when debugging is enabled. The gcc bug
apparently goes back to gcc-4.5, but slight optimization changes means
that it now showed up as a problem in 4.9.0 and 4.9.1.
The instruction scheduling problem causes gcc to schedule a spill
operation to before the stack frame has been created, which in turn can
corrupt the spilled value if an interrupt comes in. There may be other
effects of this bug too, but that's the code generation problem seen in
Michel's case.
This is fixed in current gcc HEAD, but the workaround as suggested by
Markus Trippelsdorf is pretty simple: use -fno-var-tracking-assignments
when compiling the kernel, which disables the gcc code that causes the
problem. This can result in slightly worse debug information for
variable accesses, but that is infinitely preferable to actual code
generation problems.
Doing this unconditionally (not just for CONFIG_DEBUG_INFO) also allows
non-debug builds to verify that the debug build would be identical: we
can do
export GCC_COMPARE_DEBUG=1
to make gcc internally verify that the result of the build is
independent of the "-g" flag (it will make the compiler build everything
twice, toggling the debug flag, and compare the results).
Without the "-fno-var-tracking-assignments" option, the build would fail
(even with 4.8.3 that didn't show the actual stack frame bug) with a gcc
compare failure.
See also gcc bugzilla:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=61801
Reported-by: Michel Dänzer <michel@daenzer.net>
Suggested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shortly before 3.16-rc1, Dave Jones reported:
WARNING: CPU: 3 PID: 19721 at fs/xfs/xfs_aops.c:971
xfs_vm_writepage+0x5ce/0x630 [xfs]()
CPU: 3 PID: 19721 Comm: trinity-c61 Not tainted 3.15.0+ #3
Call Trace:
xfs_vm_writepage+0x5ce/0x630 [xfs]
shrink_page_list+0x8f9/0xb90
shrink_inactive_list+0x253/0x510
shrink_lruvec+0x563/0x6c0
shrink_zone+0x3b/0x100
shrink_zones+0x1f1/0x3c0
try_to_free_pages+0x164/0x380
__alloc_pages_nodemask+0x822/0xc90
alloc_pages_vma+0xaf/0x1c0
handle_mm_fault+0xa31/0xc50
etc.
970 if (WARN_ON_ONCE((current->flags & (PF_MEMALLOC|PF_KSWAPD)) ==
971 PF_MEMALLOC))
I did not respond at the time, because a glance at the PageDirty block
in shrink_page_list() quickly shows that this is impossible: we don't do
writeback on file pages (other than tmpfs) from direct reclaim nowadays.
Dave was hallucinating, but it would have been disrespectful to say so.
However, my own /var/log/messages now shows similar complaints
WARNING: CPU: 1 PID: 28814 at fs/ext4/inode.c:1881 ext4_writepage+0xa7/0x38b()
WARNING: CPU: 0 PID: 27347 at fs/ext4/inode.c:1764 ext4_writepage+0xa7/0x38b()
from stressing some mmotm trees during July.
Could a dirty xfs or ext4 file page somehow get marked PageSwapBacked,
so fail shrink_page_list()'s page_is_file_cache() test, and so proceed
to mapping->a_ops->writepage()?
Yes, 3.16-rc1's commit 68711a7463 ("mm, migration: add destination
page freeing callback") has provided such a way to compaction: if
migrating a SwapBacked page fails, its newpage may be put back on the
list for later use with PageSwapBacked still set, and nothing will clear
it.
Whether that can do anything worse than issue WARN_ON_ONCEs, and get
some statistics wrong, is unclear: easier to fix than to think through
the consequences.
Fixing it here, before the put_new_page(), addresses the bug directly,
but is probably the worst place to fix it. Page migration is doing too
many parts of the job on too many levels: fixing it in
move_to_new_page() to complement its SetPageSwapBacked would be
preferable, except why is it (and newpage->mapping and newpage->index)
done there, rather than down in migrate_page_move_mapping(), once we are
sure of success? Not a cleanup to get into right now, especially not
with memcg cleanups coming in 3.17.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm fixes from Dave Airlie:
"This is radeon and intel fixes, and is a small bit larger than I'm
guessing you'd like it to be.
- i915: fixes 32-bit highmem i915 blank screen, semaphore hang and
runtime pm fix
- radeon: gpuvm stability fix for hangs since 3.15, and hang/reboot
regression on TN/RL devices,
The only slightly controversial one is the change to use GB for the
vm_size, which I'm letting through as its a new interface we defined
in this merge window, and I'd prefer to have the released kernel have
the final interface rather than changing it later"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix cut and paste issue for hawaii.
drm/radeon: fix irq ring buffer overflow handling
drm/i915: Simplify i915_gem_release_all_mmaps()
drm/radeon: fix error handling in radeon_vm_bo_set_addr
drm/i915: fix freeze with blank screen booting highmem
drm/i915: Reorder the semaphore deadlock check, again
drm/radeon/TN: only enable bapm on MSI systems
drm/radeon: fix VM IB handling
drm/radeon: fix handling of radeon_vm_bo_rmv v3
drm/radeon: let's use GB for vm_size (v2)
Pull sound fixes from Takashi Iwai:
"Here contains only the fixes for the new FireWire bebob driver. All
fairly trivial and local fixes, so safe to apply"
* tag 'sound-3.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: bebob: Correction for return value of special_clk_ctl_put() in error
ALSA: bebob: Correction for return value of .put callback
ALSA: bebob: Use different labels for digital input/output
ALSA: bebob: Fix a missing to unlock mutex in error handling case
Pull hwmon fix from Guenter Roeck:
"Fixes to temperature limit and vrm write operations in smsc47m192
driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (smsc47m192) Fix temperature limit and vrm write operations
Do not split the PARPORT-related symbols with the new kconfig
symbol ARCH_MIGHT_HAVE_PC_PARPORT. The split was causing incorrect
display of these symbols -- they were not being displayed together
as they should be.
Fixes: d90c3eb315 "Kconfig cleanup (PARPORT_PC dependencies)"
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org # for 3.13, 3.14, 3.15
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull blackfin fixes from Steven Miao:
"smc nor flash PM fix, pinctrl group fix, update defconfig, and build
fixes"
* tag 'blackfin-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
blackfin: vmlinux.lds.S: reserve 32 bytes space at the end of data section for XIP kernel
defconfig: BF609: update spi config name
irq: blackfin sec: drop duplicated sec priority set
blackfin: bind different groups of one pinmux function to different state name
blackfin: fix some bf5xx boards build for missing <linux/gpio.h>
pm: bf609: cleanup smc nor flash
drop smc pin state change code, pin state will be saved in pinctrl-adi2 driver
cleanup nor flash init/exit for pm suspend/resume
Signed-off-by: Steven Miao <realmz6@gmail.com>
Pull parisc fixes from Helge Deller:
"We have two trivial patches in here. One removes the SA_RESTORER
#define since on parisc we don't have the sa_restorer field in struct
sigaction, the other patch removes an unnecessary memset().
The SA_RESTORER removal patch is scheduled for stable trees, since
without it some userspace apps don't build"
* 'parisc-3.16-6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Eliminate memset after alloc_bootmem_pages
parisc: Remove SA_RESTORER define
Pull fuse fixes from Miklos Szeredi:
"These two pathes fix issues with the kernel-userspace protocol changes
in v3.15"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: add FUSE_NO_OPEN_SUPPORT flag to INIT
fuse: s_time_gran fix
The raminit register is shared register for both can0 and can1. Since commit:
32766ff net: can: Convert to use devm_ioremap_resource
devm_ioremap_resource() is used to map raminit register. When using both
interfaces the mapping for the can1 interface fails, leading to a non
functional can interface.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the usb speed of the RTL8152 is not high speed, the USB_DEV_STAT[2:1]
should be equal to [0 1]. That is, the STAT_SPEED_FULL should be equal
to 2.
There is a easy way to check the usb speed by the speed field of the
struct usb_device. Use it to replace the original metheod.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-07-24
Please pull this batch of fixes intended for the 3.16 stream...
For the mac80211 fixes, Johannes says:
"I have two fixes: one for tracing that fixes a long-standing NULL
pointer dereference, and one for a mac80211 issue that causes iwlmvm to
send invalid frames during authentication/association."
and,
"One more fix - for a bug in the newly introduced code that obtains rate
control information for stations."
For the iwlwifi fixes, Emmanuel says:
"It includes a merge damage fix. This region has been changed in -next
and -fixes quite a few times and apparently, I failed to handle it
properly, so here the fix. Along with that I have a fix from Eliad
to properly handle overlapping BSS in AP mode."
On top of that, Felix provides and ath9k fix for Tx stalls that happen
after an aggregation session failure.
Please let me know if there are problems! There are some changes
here that will cause merge conflicts in -next. Once you merge this
I can pull it into wireless-next and resolve those issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ezequiel Garcia says:
====================
net: phy: Prevent an MDIO bus from being unloaded while in use
Changes from v1:
* Dropped the unneeded module_put() on phy_attach_direct().
The motivation of this small series is to fix the current lack of relationship
between an ethernet driver and the MDIO bus behind the PHY device. In such
cases, we would find no visible link between the drivers:
$ lsmod
Module Size Used by Not tainted
mvmdio 2941 0
mvneta 22069 0
Which means nothing prevents the MDIO driver from being removed:
$ modprobe -r mvmdio
# Unable to handle kernel NULL pointer dereference at virtual address 00000060
pgd = c0004000
[00000060] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in: mvneta [last unloaded: mvmdio]
CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 3.16.0-rc5-01127-g62c0816-dirty #608
Workqueue: events_power_efficient phy_state_machine
task: df5ec840 ti: df67a000 task.ti: df67a000
PC is at phy_state_machine+0x1c/0x468
LR is at phy_state_machine+0x18/0x468
[snip]
This patchset fixes this problem by adding a pair of module_{get,put},
so the module reference count is increased when the PHY device is attached
and is decreased when the PHY is detached.
Tested with mvneta and mv643xx_eth drivers, which depend on the mvmdio
driver to handle MDIO. This series applies on both net and net-next branches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds proper module_{get,put} to prevent the MDIO bus module
from being unloaded while the phydev is connected. By doing so, we fix
a kernel panic produced when a MDIO driver is removed, but the phydev
that relies on it is attached and running.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register() registers a device which is already bound to a driver.
Hence, the driver pointer should be set properly in order to track down
the driver associated to the MDIO bus.
This will be used to allow ethernet driver to pin down a MDIO bus driver,
preventing it from being unloaded while the PHY device is running.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow set_settings() to complete succesfully even if link is
not estabilished and port type isn't known yet.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Via Simon Horman, I received the following one-liner for your net tree:
1) Fix crash when exiting from netns that uses IPVS and conntrack,
from Julian Anastasov via Simon Horman.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Promote one fix for 3.16
This fix was necessary after
9c15a24b03 ("x86/mce: Improve mcheck_init_device() error handling")
went in. What this patch did was, among others, check the return value
of misc_register and exit early if it encountered an error. Original
code sloppily didn't do that.
However,
cef12ee52b ("xen/mce: Add mcelog support for Xen platform")
made it so that xen's init routine xen_late_init_mcelog runs first. This
was needed for the xen mcelog device which is supposed to be independent
from the baremetal one.
Initially it was reported that misc_register() fails often on xen and
that's why it needed fixing. However, it is *supposed* to fail by
design, when running in dom0 so that the xen mcelog device file gets
registered first.
And *then* you need the notifier *not* unregistered on the error path so
that the timer does get deleted properly in the CPU hotplug notifier.
Btw, this fix is needed also on baremetal in the unlikely event that
misc_register(&mce_chrdev_device) fails there too.
I was unsure whether to rush it in now and decided to delay it to 3.17.
However, xen people wanted it promoted as it breaks xen when doing cpu
hotplug there. So, after a bit of simmering in tip/master for initial
smoke testing, let's move it to 3.16. It fixes a semi-regression which
got introduced in 3.16 so no need for stable tagging.
tip/x86/ras contains that exact same commit but we can't remove it
there as it is not the last one. It won't cause any merge issues, as I
confirmed locally but I should state here the special situation of this
one fix explicitly anyway.
Thanks.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
two more radeon fixes.
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix irq ring buffer overflow handling
drm/radeon: fix error handling in radeon_vm_bo_set_addr
This time in time! Just 32bit-pae fix from Hugh, semaphores fun from Chris
and a fix for runtime pm cherry-picked from next.
Paulo is still working on a fix for runtime pm when X does cursor fun when
the display is off, but that one isn't ready yet.
* tag 'drm-intel-fixes-2014-07-24' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Simplify i915_gem_release_all_mmaps()
drm/i915: fix freeze with blank screen booting highmem
drm/i915: Reorder the semaphore deadlock check, again
byReAssocCount is incremented every second resulting in
disassociated message being send every 10 seconds whether
connection or not.
byReAssocCount should only advance while eCommandState
is in WLAN_ASSOCIATE_WAIT
Change existing scope to if condition.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_bootmem and related function always return zeroed region of
memory. Thus a memset after calls to these functions is unnecessary.
The following Coccinelle semantic patch was used for making the change:
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Helge Deller <deller@gmx.de>
The sa_restorer field in struct sigaction is obsolete and no longer in
the parisc implementation. However, the core code assumes the field is
present if SA_RESTORER is defined. So, the define needs to be removed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
This fixes the following warning:
warning: (ARCH_MULTIPLATFORM && ARCH_INTEGRATOR && ARCH_SHMOBILE_LEGACY) selects ARM_PATCH_PHYS_VIRT which has unmet direct dependencies (!XIP_KERNEL && MMU && (!ARCH_REALVIEW || !SPARSEMEM))
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Temperature limit clamps are applied after converting the temperature
from milli-degrees C to degrees C, so either the clamp limit needs
to be specified in degrees C, not milli-degrees C, or clamping must
happen before converting to degrees C. Use the latter method to avoid
overflows.
vrm is an u8, so the written value needs to be limited to [0, 255].
Cc: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Merge "Two regression fixes for omaps and one fix for device
signaling" from Tony Lindgren:
- L2 cache regression fix for a warning about trying to access
a read-only register
- GPMC ECC software fallback regression fix for omap3
- Fix for dra7 pinctrl pull-up direction that causes signal issues
for anybody trying to use the internal pull up or down
* tag 'omap-for-v3.16/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: gpmc: fix gpmc_hwecc_bch_capable()
pinctrl: dra: dt-bindings: Fix pull enable/disable
ARM: OMAP2+: l2c: squelch warning dump on power control setting
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Second Round of Renesas ARM Based SoC Fixes for v3.16" from Simon Horman
* Fix SD2CKCR register address of r8a7791 (R-Car M2) SoC
This corrects a bug introduced in v3.14 by
59e79895b9 ("ARM: shmobile: r8a7791: Add clocks").
However, it does not manifest in mainline code until
SDHI devices were enabled on the Koelsch board in v3.15 by
2c60a7df72 ("ARM: shmobile: Add SDHI devices for Koelsch DTS").
It also manifests on the Henninger board when
SDHI devices were enabled in v3.16-rc1 by
1299df03d7 ("ARM: shmobile: henninger: add SDHI0/2 DT support")
* tag 'renesas-fixes2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: Fix SD2CKCR register address
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently umount on symlink blocks following umount:
/vz is separate mount
# ls /vz/ -al | grep test
drwxr-xr-x. 2 root root 4096 Jul 19 01:14 testdir
lrwxrwxrwx. 1 root root 11 Jul 19 01:16 testlink -> /vz/testdir
# umount -l /vz/testlink
umount: /vz/testlink: not mounted (expected)
# lsof /vz
# umount /vz
umount: /vz: device is busy. (unexpected)
In this case mountpoint_last() gets an extra refcount on path->mnt
Signed-off-by: Vasily Averin <vvs@openvz.org>
Acked-by: Ian Kent <raven@themaw.net>
Acked-by: Jeff Layton <jlayton@primarydata.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following warnings:
fs/direct-io.c: In function ‘__blockdev_direct_IO’:
fs/direct-io.c:1011:12: warning: ‘to’ may be used uninitialized in this function [-Wmaybe-uninitialized]
fs/direct-io.c:913:16: note: ‘to’ was declared here
fs/direct-io.c:1011:12: warning: ‘from’ may be used uninitialized in this function [-Wmaybe-uninitialized]
fs/direct-io.c:913:10: note: ‘from’ was declared here
are false positive because dio_get_page() either fails, or sets both
'from' and 'to'.
Paul Bolle said ...
Maybe it's better to move initializing "to" and "from" out of
dio_get_page(). That _might_ make it easier for both the the reader and
the compiler to understand what's going on. Something like this:
Christoph Hellwig said ...
The fix of moving the code definitively looks nicer, while I think
uninitialized_var is horrible wart that won't get anywhere near my code.
Boaz Harrosh: I agree with Christoph and Paul
Signed-off-by: Boaz Harrosh <boaz@plexistor.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
During suspend we call sched_clock_poll() to update the epoch and
accumulated time and reprogram the sched_clock_timer to fire
before the next wrap-around time. Unfortunately,
sched_clock_poll() doesn't restart the timer, instead it relies
on the hrtimer layer to do that and during suspend we aren't
calling that function from the hrtimer layer. Instead, we're
reprogramming the expires time while the hrtimer is enqueued,
which can cause the hrtimer tree to be corrupted. Furthermore, we
restart the timer during suspend but we update the epoch during
resume which seems counter-intuitive.
Let's fix this by saving the accumulated state and canceling the
timer during suspend. On resume we can update the epoch and
restart the timer similar to what we would do if we were starting
the clock for the first time.
Fixes: a08ca5d108 "sched_clock: Use an hrtimer instead of timer"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/1406174630-23458-1-git-send-email-john.stultz@linaro.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Steffen Klassert says:
====================
pull request (net): ipsec 2014-07-23
Just two fixes this time, both are stable candidates.
1) Fix the dst_entry refcount on socket policy usage.
2) Fix a wrong SPI check that prevents AH SAs from getting
installed, dependent on the SPI. From Tobias Brunner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd bugfix from Bruce Fields:
"Another regression from the xdr encoding rewrite"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
NFSD: Fix crash encoding lock reply on 32-bit
Pull arm64 fix from Catalin Marinas:
"Fix arm64 regression introduced by limiting the CMA buffer to ZONE_DMA
on platforms where RAM starts above 4GB (and ZONE_DMA becoming 0)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Create non-empty ZONE_DMA when DRAM starts above 4GB
Pull Xtensa fixes from Chris Zankel:
- resolve FIXMEs in double exception handler for window overflow. This
fix makes native building of linux on xtensa host possible;
- fix sysmem region removal issue introduced in 3.15.
* tag 'xtensa-next-20140721' of git://github.com/czankel/xtensa-linux:
xtensa: fix sysmem reservation at the end of existing block
xtensa: add fixup for double exception raised in window overflow
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for the v3.16 series. Sorry that
some of these arrive late, the summer heat in Sweden makes me slow.
- an IRQ handling fix for the STi driver, also for stable
- another IRQ fix for the RCAR GPIO driver
- a MAINTAINERS entry"
* tag 'pinctrl-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
gpio: rcar: Add support for DT IRQ flags
MAINTAINERS: Add entry for the Renesas pin controller driver
pinctrl: st: Fix irqmux handler
Pull libata regression fix from Tejun Heo:
"The last libata/for-3.16-fixes pull contained a regression introduced
by 1871ee134b ("libata: support the ata host which implements a
queue depth less than 32") which in turn was a fix for a regression
introduced earlier while changing queue tag order to accomodate hard
drives which perform poorly if tags are not allocated in circular
order (ugh...).
The regression happens only for SAS controllers making use of libata
to serve ATA devices. They don't fill an ata_host field which is used
by the new tag allocation function leading to NULL dereference.
This patch adds a new intermediate field ata_host->n_tags which is
initialized for both SAS and !SAS cases to fix the issue"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: introduce ata_host->n_tags to avoid oops on SAS controllers
Pull powerpc fixes from Ben Herrenschmidt:
"Here is a handful of powerpc fixes for 3.16. They are all pretty
simple and self contained and should still make this release"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: use _GLOBAL_TOC for memmove
powerpc/pseries: dynamically added OF nodes need to call of_node_init
powerpc: subpage_protect: Increase the array size to take care of 64TB
powerpc: Fix bugs in emulate_step()
powerpc: Disable doorbells on Power8 DD1.x
Pull slab fix from Mike Snitzer:
"This fixes the broken duplicate slab name check in
kmem_cache_sanity_check() that has been repeatedly reported (as
recently as today against Fedora rawhide).
Pekka seemed to have it staged for a late 3.15-rc in his 'slab/urgent'
branch but never sent a pull request, see:
https://lkml.org/lkml/2014/5/23/648"
* tag 'urgent-slab-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
slab_common: fix the check for duplicate slab names
Merge fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: hugetlb: fix copy_hugetlb_page_range()
simple_xattr: permit 0-size extended attributes
mm/fs: fix pessimization in hole-punching pagecache
shmem: fix splicing from a hole while it's punched
shmem: fix faulting into a hole, not taking i_mutex
mm: do not call do_fault_around for non-linear fault
sh: also try passing -m4-nofpu for SH2A builds
zram: avoid lockdep splat by revalidate_disk
mm/rmap.c: fix pgoff calculation to handle hugepage correctly
coredump: fix the setting of PF_DUMPCORE
Commit 4a705fef98 ("hugetlb: fix copy_hugetlb_page_range() to handle
migration/hwpoisoned entry") changed the order of
huge_ptep_set_wrprotect() and huge_ptep_get(), which leads to breakage
in some workloads like hugepage-backed heap allocation via libhugetlbfs.
This patch fixes it.
The test program for the problem is shown below:
$ cat heap.c
#include <unistd.h>
#include <stdlib.h>
#include <string.h>
#define HPS 0x200000
int main() {
int i;
char *p = malloc(HPS);
memset(p, '1', HPS);
for (i = 0; i < 5; i++) {
if (!fork()) {
memset(p, '2', HPS);
p = malloc(HPS);
memset(p, '3', HPS);
free(p);
return 0;
}
}
sleep(1);
free(p);
return 0;
}
$ export HUGETLB_MORECORE=yes ; export HUGETLB_NO_PREFAULT= ; hugectl --heap ./heap
Fixes 4a705fef98 ("hugetlb: fix copy_hugetlb_page_range() to handle
migration/hwpoisoned entry"), so is applicable to -stable kernels which
include it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Guillaume Morin <guillaume@morinfr.org>
Suggested-by: Guillaume Morin <guillaume@morinfr.org>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a filesystem uses simple_xattr to support user extended attributes,
LTP setxattr01 and xfstests generic/062 fail with "Cannot allocate
memory": simple_xattr_alloc()'s wrap-around test mistakenly excludes
values of zero size. Fix that off-by-one (but apparently no filesystem
needs them yet).
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jeff Layton <jlayton@poochiereds.net>
Cc: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I wanted to revert my v3.1 commit d0823576bf ("mm: pincer in
truncate_inode_pages_range"), to keep truncate_inode_pages_range() in
synch with shmem_undo_range(); but have stepped back - a change to
hole-punching in truncate_inode_pages_range() is a change to
hole-punching in every filesystem (except tmpfs) that supports it.
If there's a logical proof why no filesystem can depend for its own
correctness on the pincer guarantee in truncate_inode_pages_range() - an
instant when the entire hole is removed from pagecache - then let's
revisit later. But the evidence is that only tmpfs suffered from the
livelock, and we have no intention of extending hole-punch to ramfs. So
for now just add a few comments (to match or differ from those in
shmem_undo_range()), and fix one silliness noticed in d0823576bf4b...
Its "index == start" addition to the hole-punch termination test was
incomplete: it opened a way for the end condition to be missed, and the
loop go on looking through the radix_tree, all the way to end of file.
Fix that pessimization by resetting index when detected in inner loop.
Note that it's actually hard to hit this case, without the obsessive
concurrent faulting that trinity does: normally all pages are removed in
the initial trylock_page() pass, and this loop finds nothing to do. I
had to "#if 0" out the initial pass to reproduce bug and test fix.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shmem_fault() is the actual culprit in trinity's hole-punch starvation,
and the most significant cause of such problems: since a page faulted is
one that then appears page_mapped(), needing unmap_mapping_range() and
i_mmap_mutex to be unmapped again.
But it is not the only way in which a page can be brought into a hole in
the radix_tree while that hole is being punched; and Vlastimil's testing
implies that if enough other processors are busy filling in the hole,
then shmem_undo_range() can be kept from completing indefinitely.
shmem_file_splice_read() is the main other user of SGP_CACHE, which can
instantiate shmem pagecache pages in the read-only case (without holding
i_mutex, so perhaps concurrently with a hole-punch). Probably it's
silly not to use SGP_READ already (using the ZERO_PAGE for holes): which
ought to be safe, but might bring surprises - not a change to be rushed.
shmem_read_mapping_page_gfp() is an internal interface used by
drivers/gpu/drm GEM (and next by uprobes): it should be okay. And
shmem_file_read_iter() uses the SGP_DIRTY variant of SGP_CACHE, when
called internally by the kernel (perhaps for a stacking filesystem,
which might rely on holes to be reserved): it's unclear whether it could
be provoked to keep hole-punch busy or not.
We could apply the same umbrella as now used in shmem_fault() to
shmem_file_splice_read() and the others; but it looks ugly, and use over
a range raises questions - should it actually be per page? can these get
starved themselves?
The origin of this part of the problem is my v3.1 commit d0823576bf
("mm: pincer in truncate_inode_pages_range"), once it was duplicated
into shmem.c. It seemed like a nice idea at the time, to ensure
(barring RCU lookup fuzziness) that there's an instant when the entire
hole is empty; but the indefinitely repeated scans to ensure that make
it vulnerable.
Revert that "enhancement" to hole-punch from shmem_undo_range(), but
retain the unproblematic rescanning when it's truncating; add a couple
of comments there.
Remove the "indices[0] >= end" test: that is now handled satisfactorily
by the inner loop, and mem_cgroup_uncharge_start()/end() are too light
to be worth avoiding here.
But if we do not always loop indefinitely, we do need to handle the case
of swap swizzled back to page before shmem_free_swap() gets it: add a
retry for that case, as suggested by Konstantin Khlebnikov; and for the
case of page swizzled back to swap, as suggested by Johannes Weiner.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f00cdc6df7 ("shmem: fix faulting into a hole while it's
punched") was buggy: Sasha sent a lockdep report to remind us that
grabbing i_mutex in the fault path is a no-no (write syscall may already
hold i_mutex while faulting user buffer).
We tried a completely different approach (see following patch) but that
proved inadequate: good enough for a rational workload, but not good
enough against trinity - which forks off so many mappings of the object
that contention on i_mmap_mutex while hole-puncher holds i_mutex builds
into serious starvation when concurrent faults force the puncher to fall
back to single-page unmap_mapping_range() searches of the i_mmap tree.
So return to the original umbrella approach, but keep away from i_mutex
this time. We really don't want to bloat every shmem inode with a new
mutex or completion, just to protect this unlikely case from trinity.
So extend the original with wait_queue_head on stack at the hole-punch
end, and wait_queue item on the stack at the fault end.
This involves further use of i_lock to guard against the races: lockdep
has been happy so far, and I see fs/inode.c:unlock_new_inode() holds
i_lock around wake_up_bit(), which is comparable to what we do here.
i_lock is more convenient, but we could switch to shmem's info->lock.
This issue has been tagged with CVE-2014-4171, which will require commit
f00cdc6df7 and this and the following patch to be backported: we
suggest to 3.1+, though in fact the trinity forkbomb effect might go
back as far as 2.6.16, when madvise(,,MADV_REMOVE) came in - or might
not, since much has changed, with i_mmap_mutex a spinlock before 3.0.
Anyone running trinity on 3.0 and earlier? I don't think we need care.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Korb reported that "repeated mapping of the same file on tmpfs
using remap_file_pages sometimes triggers a BUG at mm/filemap.c:202 when
the process exits".
He bisected the bug to d7c1755179 ("mm: implement ->map_pages for
shmem/tmpfs"), although the bug was actually added by commit
8c6e50b029 ("mm: introduce vm_ops->map_pages()").
The problem is caused by calling do_fault_around for a _non-linear_
fault. In this case pgoff is shifted and might become negative during
calculation.
Faulting around non-linear page-fault makes no sense and breaks the
logic in do_fault_around because pgoff is shifted.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-by: Ingo Korb <ingo.korb@tu-dortmund.de>
Tested-by: Ingo Korb <ingo.korb@tu-dortmund.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Ning Qu <quning@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> [3.15.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When compiling a SH2A kernel (e.g. se7206_defconfig or rsk7203_defconfig)
using sh4-linux-gcc, linking fails with:
net/built-in.o: In function `__sk_run_filter':
net/core/filter.c:566: undefined reference to `__fpscr_values'
net/core/filter.c:269: undefined reference to `__fpscr_values'
...
net/built-in.o:net/core/filter.c:580: more undefined references to `__fpscr_values' follow
This happens because sh4-linux-gcc doesn't support the "-m2a-nofpu",
which is thus filtered out by "$(call cc-option, ...)".
As compiling using sh4-linux-gcc is useful for compile coverage, also
try passing "-m4-nofpu" (which is presumably filtered out when using a
real sh2a-linux toolchain) to disable the generation of FPU instructions
and references to __fpscr_values[].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I triggered VM_BUG_ON() in vma_address() when I tried to migrate an
anonymous hugepage with mbind() in the kernel v3.16-rc3. This is
because pgoff's calculation in rmap_walk_anon() fails to consider
compound_order() only to have an incorrect value.
This patch introduces page_to_pgoff(), which gets the page's offset in
PAGE_CACHE_SIZE.
Kirill pointed out that page cache tree should natively handle
hugepages, and in order to make hugetlbfs fit it, page->index of
hugetlbfs page should be in PAGE_CACHE_SIZE. This is beyond this patch,
but page_to_pgoff() contains the point to be fixed in a single function.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 079148b919 ("coredump: factor out the setting of PF_DUMPCORE")
cleaned up the setting of PF_DUMPCORE by removing it from all the
linux_binfmt->core_dump() and moving it to zap_threads().But this ended
up clearing all the previously set flags. This causes issues during
core generation when tsk->flags is checked again (eg. for PF_USED_MATH
to dump floating point registers). Fix this.
Signed-off-by: Silesh C V <svellattu@mvista.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert half of commit d151f9854f: If isochronous I/O is attempted with
packets larget than 1 kByte, VIA VT6315 rev 01 immediately stops to generate
any interrupts if MSI are used. Fix this by going back to legacy interrupts.
[Thread "Isochronous streaming with VT6315 OHCI",
http://marc.info/?t=139049641500003]
With smaller packets, the loss of IRQs happens too but only very rarely ---
rarely eneough that it was not yet possible for me to determine whether
QUIRK_NO_MSI is an actual fix for this rare variation of this chip bug.
I am keeping QUIRK_CYCLE_TIMER off of VT6315 rev >= 1 because this has been
verified by myself with certainty. On the other hand, I am also keeping
QUIRK_CYCLE_TIMER on for VT6315 rev 0 because I don't know at this time
whether this revision accesses Cycle Timer non-atomically like most of the
other VIA OHCIs are known to do.
Reported-by: Rémy Bruno <remy-fw@remy.trinnov.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If an aggregation session fails, frames still end up in the driver queue
with IEEE80211_TX_CTL_AMPDU set.
This causes tx for the affected station/tid to stall, since
ath_tx_get_tid_subframe returning packets to send.
Fix this by clearing IEEE80211_TX_CTL_AMPDU as long as no aggregation
session is running.
Cc: stable@vger.kernel.org
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P4 systems with cpuid level < 4 can have SMT, but the cache topology
description available (cpuid2) does not include SMP information.
Now we know that SMT shares all cache levels, and therefore we can
mark all available cache levels as shared.
We do this by setting cpu_llc_id to ->phys_proc_id, since that's
the same for each SMT thread. We can do this unconditional since if
there's no SMT its still true, the one CPU shares cache with only
itself.
This fixes a problem where such CPUs report an incorrect LLC CPU mask.
This in turn fixes a crash in the scheduler where the topology was
build wrong, it assumes the LLC mask to include at least the SMT CPUs.
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140722133514.GM12054@laptop.lan
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Commit 8c7424cff6 "nfsd4: don't try to encode conflicting owner if low
on space" forgot to free conf->data in nfsd4_encode_lockt and before
sign conf->data to NULL in nfsd4_encode_lock_denied, causing a leak.
Worse, kfree() can be called on an uninitialized pointer in the case of
a succesful lock (or one that fails for a reason other than a conflict).
(Note that lock->lk_denied.ld_owner.data appears it should be zero here,
until you notice that it's one arm of a union the other arm of which is
written to in the succesful case by the
memcpy(&lock->lk_resp_stateid, &lock_stp->st_stid.sc_stateid,
sizeof(stateid_t));
in nfsd4_lock(). In the 32-bit case this overwrites ld_owner.data.)
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Fixes: 8c7424cff6 ""nfsd4: don't try to encode conflicting owner if low on space"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
An object can only have an active gtt mapping if it is currently bound
into the global gtt. Therefore we can simply walk the list of all bound
objects and check the flag upon those for an active gtt mapping.
From commit 48018a57a8
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Dec 13 15:22:31 2013 -0200
drm/i915: release the GTT mmaps when going into D3
Also note that the WARN is inappropriate for this function as GPU
activity is orthogonal to GTT mmap status. Rather it is the caller that
relies upon this condition and so it should assert that the GPU is idle
itself.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80081
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: cherry-pick from -next to -fixes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ZONE_DMA is created to allow 32-bit only devices to access memory in the
absence of an IOMMU. On systems where the memory starts above 4GB, it is
expected that some devices have a DMA offset hardwired to be able to
access the bottom of the memory. Linux currently supports DT bindings
for the DMA offsets but they are not (easily) available early during
boot.
This patch tries to guess a DMA offset and assumes that ZONE_DMA
corresponds to the 32-bit mask above the start of DRAM.
Fixes: 2d5a5612bc (arm64: Limit the CMA buffer to 32-bit if ZONE_DMA)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Tested-by: Anup Patel <anup.patel@linaro.org>
This patch adds bch8 ecc software fallback which is mostly used by
omap3s because they lack hardware elm support.
Fixes: 0611c41934 (ARM: OMAP2+: gpmc:
update gpmc_hwecc_bch_capable() for new platforms and ECC schemes)
Cc: <stable@vger.kernel.org> # 3.15.x+
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA74/72 control module pins have a weak pull up and pull down.
This is configured by bit offset 17. if BIT(17) is 1, a pull up is
selected, else a pull down is selected.
However, this pull resisstor is applied based on BIT(16) -
PULLUDENABLE - if BIT(18) is *0*, then pull as defined in BIT(17) is
applied, else no weak pulls are applied. We defined this in reverse.
Reference: Table 18-5 (Description of the pad configuration register
bits) in Technical Reference Manual Revision (DRA74x revision Q:
SPRUHI2Q Revised June 2014 and DRA72x revision F: SPRUHP2F - Revised
June 2014)
Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the recent commit b50a6c584b "Clear MMCR2 when enabling PMU", I
screwed up the handling of MMCR2 for tasks using EBB.
We must make sure we set MMCR2 *before* ebb_switch_in(), otherwise we
overwrite the value of MMCR2 that userspace may have written. That
potentially breaks a task that uses EBB and manually uses MMCR2 for
event freezing.
Fixes: b50a6c584b ("powerpc/perf: Clear MMCR2 when enabling PMU")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Packets shorter than ETH_ZLEN were not padded with zeroes, hence leaking
potentially sensitive information. This bug has been present since the
driver got accepted in commit 1c1008c793
("net: bcmgenet: add main driver file").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason reported an oops caused by SCTP on his ARM machine with
SCTP authentication enabled:
Internal error: Oops: 17 [#1] ARM
CPU: 0 PID: 104 Comm: sctp-test Not tainted 3.13.0-68744-g3632f30c9b20-dirty #1
task: c6eefa40 ti: c6f52000 task.ti: c6f52000
PC is at sctp_auth_calculate_hmac+0xc4/0x10c
LR is at sg_init_table+0x20/0x38
pc : [<c024bb80>] lr : [<c00f32dc>] psr: 40000013
sp : c6f538e8 ip : 00000000 fp : c6f53924
r10: c6f50d80 r9 : 00000000 r8 : 00010000
r7 : 00000000 r6 : c7be4000 r5 : 00000000 r4 : c6f56254
r3 : c00c8170 r2 : 00000001 r1 : 00000008 r0 : c6f1e660
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005397f Table: 06f28000 DAC: 00000015
Process sctp-test (pid: 104, stack limit = 0xc6f521c0)
Stack: (0xc6f538e8 to 0xc6f54000)
[...]
Backtrace:
[<c024babc>] (sctp_auth_calculate_hmac+0x0/0x10c) from [<c0249af8>] (sctp_packet_transmit+0x33c/0x5c8)
[<c02497bc>] (sctp_packet_transmit+0x0/0x5c8) from [<c023e96c>] (sctp_outq_flush+0x7fc/0x844)
[<c023e170>] (sctp_outq_flush+0x0/0x844) from [<c023ef78>] (sctp_outq_uncork+0x24/0x28)
[<c023ef54>] (sctp_outq_uncork+0x0/0x28) from [<c0234364>] (sctp_side_effects+0x1134/0x1220)
[<c0233230>] (sctp_side_effects+0x0/0x1220) from [<c02330b0>] (sctp_do_sm+0xac/0xd4)
[<c0233004>] (sctp_do_sm+0x0/0xd4) from [<c023675c>] (sctp_assoc_bh_rcv+0x118/0x160)
[<c0236644>] (sctp_assoc_bh_rcv+0x0/0x160) from [<c023d5bc>] (sctp_inq_push+0x6c/0x74)
[<c023d550>] (sctp_inq_push+0x0/0x74) from [<c024a6b0>] (sctp_rcv+0x7d8/0x888)
While we already had various kind of bugs in that area
ec0223ec48 ("net: sctp: fix sctp_sf_do_5_1D_ce to verify if
we/peer is AUTH capable") and b14878ccb7 ("net: sctp: cache
auth_enable per endpoint"), this one is a bit of a different
kind.
Giving a bit more background on why SCTP authentication is
needed can be found in RFC4895:
SCTP uses 32-bit verification tags to protect itself against
blind attackers. These values are not changed during the
lifetime of an SCTP association.
Looking at new SCTP extensions, there is the need to have a
method of proving that an SCTP chunk(s) was really sent by
the original peer that started the association and not by a
malicious attacker.
To cause this bug, we're triggering an INIT collision between
peers; normal SCTP handshake where both sides intent to
authenticate packets contains RANDOM; CHUNKS; HMAC-ALGO
parameters that are being negotiated among peers:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
RFC4895 says that each endpoint therefore knows its own random
number and the peer's random number *after* the association
has been established. The local and peer's random number along
with the shared key are then part of the secret used for
calculating the HMAC in the AUTH chunk.
Now, in our scenario, we have 2 threads with 1 non-blocking
SEQ_PACKET socket each, setting up common shared SCTP_AUTH_KEY
and SCTP_AUTH_ACTIVE_KEY properly, and each of them calling
sctp_bindx(3), listen(2) and connect(2) against each other,
thus the handshake looks similar to this, e.g.:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
<--------- INIT[RANDOM; CHUNKS; HMAC-ALGO] -----------
-------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] -------->
...
Since such collisions can also happen with verification tags,
the RFC4895 for AUTH rather vaguely says under section 6.1:
In case of INIT collision, the rules governing the handling
of this Random Number follow the same pattern as those for
the Verification Tag, as explained in Section 5.2.4 of
RFC 2960 [5]. Therefore, each endpoint knows its own Random
Number and the peer's Random Number after the association
has been established.
In RFC2960, section 5.2.4, we're eventually hitting Action B:
B) In this case, both sides may be attempting to start an
association at about the same time but the peer endpoint
started its INIT after responding to the local endpoint's
INIT. Thus it may have picked a new Verification Tag not
being aware of the previous Tag it had sent this endpoint.
The endpoint should stay in or enter the ESTABLISHED
state but it MUST update its peer's Verification Tag from
the State Cookie, stop any init or cookie timers that may
running and send a COOKIE ACK.
In other words, the handling of the Random parameter is the
same as behavior for the Verification Tag as described in
Action B of section 5.2.4.
Looking at the code, we exactly hit the sctp_sf_do_dupcook_b()
case which triggers an SCTP_CMD_UPDATE_ASSOC command to the
side effect interpreter, and in fact it properly copies over
peer_{random, hmacs, chunks} parameters from the newly created
association to update the existing one.
Also, the old asoc_shared_key is being released and based on
the new params, sctp_auth_asoc_init_active_key() updated.
However, the issue observed in this case is that the previous
asoc->peer.auth_capable was 0, and has *not* been updated, so
that instead of creating a new secret, we're doing an early
return from the function sctp_auth_asoc_init_active_key()
leaving asoc->asoc_shared_key as NULL. However, we now have to
authenticate chunks from the updated chunk list (e.g. COOKIE-ACK).
That in fact causes the server side when responding with ...
<------------------ AUTH; COOKIE-ACK -----------------
... to trigger a NULL pointer dereference, since in
sctp_packet_transmit(), it discovers that an AUTH chunk is
being queued for xmit, and thus it calls sctp_auth_calculate_hmac().
Since the asoc->active_key_id is still inherited from the
endpoint, and the same as encoded into the chunk, it uses
asoc->asoc_shared_key, which is still NULL, as an asoc_key
and dereferences it in ...
crypto_hash_setkey(desc.tfm, &asoc_key->data[0], asoc_key->len)
... causing an oops. All this happens because sctp_make_cookie_ack()
called with the *new* association has the peer.auth_capable=1
and therefore marks the chunk with auth=1 after checking
sctp_auth_send_cid(), but it is *actually* sent later on over
the then *updated* association's transport that didn't initialize
its shared key due to peer.auth_capable=0. Since control chunks
in that case are not sent by the temporary association which
are scheduled for deletion, they are issued for xmit via
SCTP_CMD_REPLY in the interpreter with the context of the
*updated* association. peer.auth_capable was 0 in the updated
association (which went from COOKIE_WAIT into ESTABLISHED state),
since all previous processing that performed sctp_process_init()
was being done on temporary associations, that we eventually
throw away each time.
The correct fix is to update to the new peer.auth_capable
value as well in the collision case via sctp_assoc_update(),
so that in case the collision migrated from 0 -> 1,
sctp_auth_asoc_init_active_key() can properly recalculate
the secret. This therefore fixes the observed server panic.
Fixes: 730fc3d05c ("[SCTP]: Implete SCTP-AUTH parameter processing")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the expected throughput is queried before rate control has been
initialized, the minstrel op for it will crash while trying to access
the rate table.
Check for WLAN_STA_RATE_CONTROL before attempting to use the rate
control op.
Reported-by: Jean-Pierre Tosoni <jp.tosoni@acksys.fr>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here some additional changes to set a capability flag so that clients can
detect when it's appropriate to return -ENOSYS from open.
This amends the following commit introduced in 3.14:
7678ac5061 fuse: support clients that don't implement 'open'
However we can only add the flag to 3.15 and later since there was no
protocol version update in 3.14.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: <stable@vger.kernel.org> # v3.15+
This commit is for correction of my misunderstanding about return value of
.put callback in ALSA Control interface.
According to 'Writing ALSA Driver' (*1), return value of the callback has
three patterns; 1: changed, 0: not changed, an negative value: fatal error.
But I misunderstood that it's boolean; zero or nonzero.
*1: Writing an ALSA Driver (2005, Takashi Iwai)
http://www.alsa-project.org/main/index.php/ALSA_Driver_Documentation
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit uses different labels for control elements of digital input/output
interfaces to correct my misunderstanding about M-Audio Firewire 1814 and
ProjectMix I/O.
According to user manuals for these two models, they have two modes for
digital input; one is S/PDIF in both of optical and coaxial interfaces,
another is ADAT in optical interface only.
But in current implementation, a control element for it reduced labels which
a control element for digital output uses because of my misunderstanding
that optical interface is not available for digital input with S/PDIF mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In error handling case, special_clk_ctl_put() returns without unlock_mutex(),
therefore the mutex is still locked. This commit moves mutex_lock() after
the error handling case.
This commit is my solution for this post.
[PATCH -next] ALSA: bebob: Fix missing unlock on error in special_clk_ctl_put()
https://lkml.org/lkml/2014/7/20/12
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 554086d ("x86_32, entry: Do syscall exit work on badsys
(CVE-2014-4508)") introduced a regression in the x86_32 syscall entry
code, resulting in syscall() not returning proper errors for undefined
syscalls on CPUs supporting the sysenter feature.
The following code:
> int result = syscall(666);
> printf("result=%d errno=%d error=%s\n", result, errno, strerror(errno));
results in:
> result=666 errno=0 error=Success
Obviously, the syscall return value is the called syscall number, but it
should have been an ENOSYS error. When run under ptrace it behaves
correctly, which makes it hard to debug in the wild:
> result=-1 errno=38 error=Function not implemented
The %eax register is the return value register. For debugging via ptrace
the syscall entry code stores the complete register context on the
stack. The badsys handlers only store the ENOSYS error code in the
ptrace register set and do not set %eax like a regular syscall handler
would. The old resume_userspace call chain contains code that clobbers
%eax and it restores %eax from the ptrace registers afterwards. The same
goes for the ptrace-enabled call chain. When ptrace is not used, the
syscall return value is the passed-in syscall number from the untouched
%eax register.
Use %eax as the return value register in syscall_badsys and
sysenter_badsys, like a real syscall handler does, and have the caller
push the value onto the stack for ptrace access.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.11.1407221022380.31021@titan.int.lan.stealer.net
Reviewed-and-tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: <stable@vger.kernel.org> # If 554086d is backported
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
x86_64 boots and displays fine, but booting x86_32 with CONFIG_HIGHMEM
has frozen with a blank screen throughout 3.16-rc on this ThinkPad T420s,
with i915 generation 6 graphics.
Fix 9d0a6fa6c5 ("drm/i915: add render state initialization"): kunmap()
takes struct page * argument, not virtual address. Which the compiler
kindly points out, if you use the appropriate u32 *batch, instead of
silencing it with a void *.
Why did bisection lead decisively to nearby 229b0489aa ("drm/i915:
add null render states for gen6, gen7 and gen8")? Because the u32
deposited at that virtual address by the previous stub failed the
PageHighMem test, and so did no harm.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
memmove may be called from module code copy_pages(btrfs), and it may
call memcpy, which may call back to C code, so it needs to use
_GLOBAL_TOC to set up r2 correctly.
This fixes following error when I tried to boot an le guest:
Vector: 300 (Data Access) at [c000000073f97210]
pc: c000000000015004: enable_kernel_altivec+0x24/0x80
lr: c000000000058fbc: enter_vmx_copy+0x3c/0x60
sp: c000000073f97490
msr: 8000000002009033
dar: d000000001d50170
dsisr: 40000000
current = 0xc0000000734c0000
paca = 0xc00000000fff0000 softe: 0 irq_happened: 0x01
pid = 815, comm = mktemp
enter ? for help
[c000000073f974f0] c000000000058fbc enter_vmx_copy+0x3c/0x60
[c000000073f97510] c000000000057d34 memcpy_power7+0x274/0x840
[c000000073f97610] d000000001c3179c copy_pages+0xfc/0x110 [btrfs]
[c000000073f97660] d000000001c3c248 memcpy_extent_buffer+0xe8/0x160 [btrfs]
[c000000073f97700] d000000001be4be8 setup_items_for_insert+0x208/0x4a0 [btrfs]
[c000000073f97820] d000000001be50b4 btrfs_insert_empty_items+0xf4/0x140 [btrfs]
[c000000073f97890] d000000001bfed30 insert_with_overflow+0x70/0x180 [btrfs]
[c000000073f97900] d000000001bff174 btrfs_insert_dir_item+0x114/0x2f0 [btrfs]
[c000000073f979a0] d000000001c1f92c btrfs_add_link+0x10c/0x370 [btrfs]
[c000000073f97a40] d000000001c20e94 btrfs_create+0x204/0x270 [btrfs]
[c000000073f97b00] c00000000026d438 vfs_create+0x178/0x210
[c000000073f97b50] c000000000270a70 do_last+0x9f0/0xe90
[c000000073f97c20] c000000000271010 path_openat+0x100/0x810
[c000000073f97ce0] c000000000272ea8 do_filp_open+0x58/0xd0
[c000000073f97dc0] c00000000025ade8 do_sys_open+0x1b8/0x300
[c000000073f97e30] c00000000000a008 syscall_exit+0x0/0x7c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 75b57ecf9 refactored device tree nodes to use kobjects such that they
can be exposed via /sysfs. A secondary commit 0829f6d1f furthered this rework
by moving the kobect initialization logic out of of_node_add into its own
of_node_init function. The inital commit removed the existing kref_init calls
in the pseries dlpar code with the assumption kobject initialization would
occur in of_node_add. The second commit had the side effect of triggering a
BUG_ON during DLPAR, migration and suspend/resume operations as a result of
dynamically added nodes being uninitialized.
This patch fixes this by adding of_node_init calls in place of the previously
removed kref_init calls.
Fixes: 0829f6d1f6 ("of: device_node kobject lifecycle fixes")
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We now support TASK_SIZE of 16TB, hence the array should be 8.
Fixes the below crash:
Unable to handle kernel paging request for data at address 0x000100bd
Faulting instruction address: 0xc00000000004f914
cpu 0x13: Vector: 300 (Data Access) at [c000000fea75fa90]
pc: c00000000004f914: .sys_subpage_prot+0x2d4/0x5c0
lr: c00000000004fb5c: .sys_subpage_prot+0x51c/0x5c0
sp: c000000fea75fd10
msr: 9000000000009032
dar: 100bd
dsisr: 40000000
current = 0xc000000fea6ae490
paca = 0xc00000000fb8ab00 softe: 0 irq_happened: 0x00
pid = 8237, comm = a.out
enter ? for help
[c000000fea75fe30] c00000000000a164 syscall_exit+0x0/0x98
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes some bugs in emulate_step(). First, the setting of the carry
bit for the arithmetic right-shift instructions was not correct on 64-bit
machines because we were masking with a mask of type int rather than
unsigned long. Secondly, the sld (shift left doubleword) instruction was
using the wrong instruction field for the register containing the shift
count.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These processors do not currently support doorbell IPIs, so remove them
from the feature list if we are at DD 1.xx for the 0x004d part.
This fixes a regression caused by d4e58e5928 (powerpc/powernv: Enable
POWER8 doorbell IPIs). With that patch the kernel would hang at boot
when calling smp_call_function_many, as the doorbell would not be
received by the target CPUs:
.smp_call_function_many+0x2bc/0x3c0 (unreliable)
.on_each_cpu_mask+0x30/0x100
.cpuidle_register_driver+0x158/0x1a0
.cpuidle_register+0x2c/0x110
.powernv_processor_idle_init+0x23c/0x2c0
.do_one_initcall+0xd4/0x260
.kernel_init_freeable+0x25c/0x33c
.kernel_init+0x1c/0x120
.ret_from_kernel_thread+0x58/0x7c
Fixes: d4e58e5928 (powerpc/powernv: Enable POWER8 doorbell IPIs)
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull networking fixes from David Miller:
1) Null termination fix in dns_resolver got the pointer dereferncing
wrong, fix from Ben Hutchings.
2) ip_options_compile() has a benign but real buffer overflow when
parsing options. From Eric Dumazet.
3) Table updates can crash in netfilter's nftables if none of the state
flags indicate an actual change, from Pablo Neira Ayuso.
4) Fix race in nf_tables dumping, also from Pablo.
5) GRE-GRO support broke the forwarding path because the segmentation
state was not fully initialized in these paths, from Jerry Chu.
6) sunvnet driver leaks objects and potentially crashes on module
unload, from Sowmini Varadhan.
7) We can accidently generate the same handle for several u32
classifier filters, fix from Cong Wang.
8) Several edge case bug fixes in fragment handling in xen-netback,
from Zoltan Kiss.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
ipv4: fix buffer overflow in ip_options_compile()
batman-adv: fix TT VLAN inconsistency on VLAN re-add
batman-adv: drop QinQ claim frames in bridge loop avoidance
dns_resolver: Null-terminate the right string
xen-netback: Fix pointer incrementation to avoid incorrect logging
xen-netback: Fix releasing header slot on error path
xen-netback: Fix releasing frag_list skbs in error path
xen-netback: Fix handling frag_list on grant op error path
net_sched: avoid generating same handle for u32 filters
net: huawei_cdc_ncm: add "subclass 3" devices
net: qmi_wwan: add two Sierra Wireless/Netgear devices
wan/x25_asy: integer overflow in x25_asy_change_mtu()
net: ppp: fix creating PPP pass and active filters
net/mlx4_en: cq->irq_desc wasn't set in legacy EQ's
sunvnet: clean up objects created in vnet_new() on vnet_exit()
r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_40
net-gre-gro: Fix a bug that breaks the forwarding path
netfilter: nf_tables: 64bit stats need some extra synchronization
netfilter: nf_tables: set NLM_F_DUMP_INTR if netlink dumping is stale
netfilter: nf_tables: safe RCU iteration on list when dumping
...
Pull sparc fix from David Miller:
"Need to hook up the new renameat2 system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Hook up renameat2 syscall.
Pull IDE fixes from David Miller:
- fix interrupt registry for some Atari IDE chipsets.
- adjust Kconfig dependencies for x86_32 specific chips.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: Fix SC1200 dependencies
ide: Fix CS5520 and CS5530 dependencies
m68k/atari - ide: do not register interrupt if host->get_lock is set
Pull trace fix from Steven Rostedt:
"Tony Luck found that using the "uptime" trace clock that uses jiffies
as a counter was converted to nanoseconds (silly), and after 1 hour 11
minutes and 34 seconds, this monotonic clock would wrap, causing havoc
with the tracing system and making the clock useless.
He converted that clock to use jiffies_64 and made it into a counter
instead of nanosecond conversions, and displayed the clock with the
straight jiffy count, which works much better than it did in the past"
* tag 'trace-fixes-v3.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix wraparound problems in "uptime" trace clock
Antonio Quartulli says:
====================
pull request [net]: batman-adv 20140721
here you have two fixes that we have been testing for quite some time
(this is why they arrived a bit late in the rc cycle).
Patch 1) ensures that BLA packets get dropped and not forwarded to the
mesh even if they reach batman-adv within QinQ frames. Forwarding them
into the mesh means messing up with the TT database of other nodes which
can generate all kind of unexpected behaviours during route computation.
Patch 2) avoids a couple of race conditions triggered upon fast VLAN
deletion-addition. Such race conditions are pretty dangerous because
they not only create inconsistencies in the TT database of the nodes
in the network, but such scenario is also unrecoverable (unless
nodes are rebooted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/TN: only enable bapm on MSI systems
drm/radeon: fix VM IB handling
drm/radeon: fix handling of radeon_vm_bo_rmv v3
drm/radeon: let's use GB for vm_size (v2)
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
Pull block fixes from Jens Axboe:
"Final block fixes for 3.16
Four small fixes that should go into 3.16, have been queued up for a
bit and delayed due to vacation and other euro duties. But here they
are. The pull request contains:
- Fix for a reported crash with shared tagging on SCSI from Christoph
- A regression fix for drbd. From Lars Ellenberg.
- Hooking up the compat ioctl for BLKZEROOUT, which requires no
translation. From Mikulas.
- A fix for a regression where we woud crash on queue exit if the
root_blkg is gone/not there. From Tejun"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: provide compat ioctl for BLKZEROOUT
blkcg: don't call into policy draining if root_blkg is already gone
drbd: fix regression 'out of mem, failed to invoke fence-peer helper'
block: don't assume last put of shared tags is for the host
Pull libata fixes from Tejun Heo:
"Late libata fixes.
The most important one is from Kevin Hao which makes sure that libata
only allocates tags inside the max tag number the controller supports.
libata always had this problem but the recent tag allocation change
and addition of support for sata_fsl which only supports queue depth
of 16 exposed the issue.
Hans de Goede agreed to become the maintainer of libahci_platform
which is under higher than usual development pressure from all the new
controllers popping up from the ARM world"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
drivers/ata/pata_ep93xx.c: use signed int type for result of platform_get_irq()
libata: EH should handle AMNF error condition as a media error
libata: support the ata host which implements a queue depth less than 32
MAINTAINERS: Add Hans de Goede as ahci-platform maintainer
Pull kvm fixes from Paolo Bonzini:
"These are mostly PPC changes for 3.16-new things. However, there is
an x86 change too and it is a regression from 3.14. As it only
affects nested virtualization and there were other changes in this
area in 3.16, I am not nominating it for 3.15-stable"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Check for nested events if there is an injectable interrupt
KVM: PPC: RTAS: Do byte swaps explicitly
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
PPC: Add _GLOBAL_TOC for 32bit
KVM: PPC: BOOK3S: HV: Use base page size when comparing against slb value
KVM: PPC: Book3E: Unlock mmu_lock when setting caching atttribute
Pull s390 fixes from Martin Schwidefsky:
"A couple of last minute bug fixes for 3.16, including a fix for ptrace
to close a hole which allowed a user space program to write to the
kernel address space"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix restore of invalid floating-point-control
s390/zcrypt: improve device probing for zcrypt adapter cards
s390/ptrace: fix PSW mask check
s390/MSI: Use standard mask and unmask funtions
s390/3270: correct size detection with the read-partition command
s390: require mvcos facility, not tod clock steering facility
Jonathan writes:
Fifth set of fixes for IIO in the 3.16 cycle.
One nasty one that has been around a long time and a couple of non compliant
ABI fixes.
* The demux code used to split out desired channels for devices that only
support reading sets of channels at one time had a bug where it was
building it's conversion tables against the wrong bitmap resulting in
it never actually demuxing anything. This is an old bug, but will be
effecting an increasing number of drivers as it is often used to avoid
some fiddly code in the individual drivers.
* bma180 and mma8452 weren't obeying the ABI wrt to units for acceleration.
Were in G rather than m/s^2. A little input check was missing from bma180
that might lead to acceptance of incorrect values. This last one is minor
but might lead to incorrect userspace code working and problems in the
future.
Calling radeon_vm_bo_find on the IB BO during CS
is illegal and can lead to an crash.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VM sizes smaller than 1GB doesn't make much sense anyway.
v2: fix typo and grammer
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BorisO reports that misc_register() fails often on xen. The current code
unregisters the CPU hotplug notifier in that case. If then a CPU is
offlined and onlined back again, we end up with a second timer running
on that CPU, leading to soft lockups and system hangs.
So let's leave the hotcpu notifier always registered - even if
mce_device_create failed for some cores and never unreg it so that we
can deal with the timer handling accordingly.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1403274493-1371-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The "uptime" trace clock added in:
commit 8aacf017b0
tracing: Add "uptime" trace clock that uses jiffies
has wraparound problems when the system has been up more
than 1 hour 11 minutes and 34 seconds. It converts jiffies
to nanoseconds using:
(u64)jiffies_to_usecs(jiffy) * 1000ULL
but since jiffies_to_usecs() only returns a 32-bit value, it
truncates at 2^32 microseconds. An additional problem on 32-bit
systems is that the argument is "unsigned long", so fixing the
return value only helps until 2^32 jiffies (49.7 days on a HZ=1000
system).
Avoid these problems by using jiffies_64 as our basis, and
not converting to nanoseconds (we do convert to clock_t because
user facing API must not be dependent on internal kernel
HZ values).
Link: http://lkml.kernel.org/p/99d63c5bfe9b320a3b428d773825a37095bf6a51.1405708254.git.tony.luck@intel.com
Cc: stable@vger.kernel.org # 3.10+
Fixes: 8aacf017b0 "tracing: Add "uptime" trace clock that uses jiffies"
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When a VLAN interface (on top of batX) is removed and
re-added within a short timeframe TT does not have enough
time to properly cleanup. This creates an internal TT state
mismatch as the newly created softif_vlan will be
initialized from scratch with a TT client count of zero
(even if TT entries for this VLAN still exist). The
resulting TT messages are bogus due to the counter / tt
client listing mismatch, thus creating inconsistencies on
every node in the network
To fix this issue destroy_vlan() has to not free the VLAN
object immediately but it has to be kept alive until all the
TT entries for this VLAN have been removed. destroy_vlan()
still removes the sysfs folder so that the user has the
feeling that everything went fine.
If the same VLAN is re-added before the old object is free'd,
then the latter is resurrected and re-used.
Implement such behaviour by increasing the reference counter
of a softif_vlan object every time a new local TT entry for
such VLAN is created and remove the object from the list
only when all the TT entries have been destroyed.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In AP mode, configure the fw to pass beacons from
foreign APs, in order to be able to set the ht
protection IE properly.
Add the same filters in case of GO (which didn't have
any configured filter_flags, probably by mistake)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since bridge loop avoidance only supports untagged or simple 802.1q
tagged VLAN claim frames, claim frames with stacked VLAN headers (QinQ)
should be detected and dropped. Transporting the over the mesh may cause
problems on the receivers, or create bogus entries in the local tt
tables.
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
*_result[len] is parsed as *(_result[len]) which is not at all what we
want to touch here.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 84a7c0b1db ("dns_resolver: assure that dns_query() result is null-terminated")
Signed-off-by: David S. Miller <davem@davemloft.net>
Zoltan Kiss says:
====================
xen-netback: Fixing up xenvif_tx_check_gop
This series fixes a lot of bugs on the error path around this function, which
were introduced with my grant mapping series in 3.15. They apply to the latest
net tree, but probably to net-next as well without any modification.
I'll post an another series which applies to 3.15 stable, as the problem was
first discovered there. The only difference is that the "queue" variable name is
replaced to "vif".
====================
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reported-by: Armin Zentai <armin.zentai@ezit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes this function aware that the first frag and the header might
share the same ring slot. That could happen if the first slot is bigger than
PKT_PROT_LEN. Due to this the error path might release that slot twice or never,
depending on the error scenario.
xenvif_idx_release is also removed from xenvif_idx_unmap, and called separately.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reported-by: Armin Zentai <armin.zentai@ezit.hu>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When kernel generates a handle for a u32 filter, it tries to start
from the max in the bucket. So when we have a filter with the max (fff)
handle, it will cause kernel always generates the same handle for new
filters. This can be shown by the following command:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 parent ffff: protocol ip pref 770 handle 800::fff u32 match ip protocol 1 0xff
tc filter add dev eth0 parent ffff: protocol ip pref 770 u32 match ip protocol 1 0xff
...
we will get some u32 filters with same handle:
# tc filter show dev eth0 parent ffff:
filter protocol ip pref 770 u32
filter protocol ip pref 770 u32 fh 800: ht divisor 1
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
handles should be unique. This patch fixes it by looking up a bitmap,
so that can guarantee the handle is as unique as possible. For compatibility,
we still start from 0x800.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We attempt to remove noise from coordinates reported by devices in
input_handle_abs_event(), unfortunately, unless we were dropping the
event altogether, we were ignoring the adjusted value and were passing
on the original value instead.
Cc: stable@vger.kernel.org
Reviewed-by: Andrew de los Reyes <adlr@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
val2 should be zero
This will make no difference for correct inputs but will reject
incorrect ones with a decimal part in the value written to the sysfs
interface.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
The userspace interface for acceleration sensors is documented as using
m/s^2 units [Documentation/ABI/testing/sysfs-bus-iio]
The fullscale raw values for the BMA80 corresponds to -/+ 1, 1.5, 2, etc G
depending on the selected mode.
The scale table was converting to G rather than m/s^2.
Change the scaling table to match the documented interface.
See commit 71702e6e, iio: mma8452: Use correct acceleration units,
for a related fix.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
When creating the demux table we need to iterate over the selected scan mask for
the buffer to get the samples which should be copied to destination buffer.
Right now the code uses the mask which contains all active channels, which means
the demux table contains entries which causes it to copy all the samples from
source to destination buffer one by one without doing any demuxing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].
Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.
Signed-off-by: Romain Degez <romain.degez@gmail.com>
Tested-by: Romain Degez <romain.degez@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add #ifdef CONFIG_PM_SLEEP around keyscan_supend() and keyscan_resume() to
fix the following compiler warnings occuring if CONFIG_PM_SLEEP is unset:
+ /scratch/kisskb/src/drivers/input/keyboard/st-keyscan.c: warning: 'keyscan_resume' defined but not used [-Wunused-function]: => 235:12
+ /scratch/kisskb/src/drivers/input/keyboard/st-keyscan.c: warning: 'keyscan_suspend' defined but not used [-Wunused-function]: => 218:12
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lkml.org/lkml/2014/7/8/109
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit 431a84b1a4
("ARM: 8034/1: Disable preemption in iwmmxt_task_enable()")
introduced macros {inc,dec}_preempt_count to iwmmxt_task_enable
to make it run with preemption disabled.
Unfortunately, other functions in iwmmxt.S also use concan_{save,dump,load}
sections located in iwmmxt_task_enable() to deal with iWMMXt coprocessor.
This causes an unbalanced preempt_count due to excessive dec_preempt_count
and destroyed return addresses in callers of concan_ labels due to a register
collision:
Linux version 3.16.0-rc3-00062-gd92a333-dirty (jef@armhf) (gcc version 4.8.3 (Debian 4.8.3-4) ) #5 PREEMPT Thu Jul 3 19:46:39 CEST 2014
CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine model: SolidRun CuBox
...
PJ4 iWMMXt v2 coprocessor enabled.
...
Unable to handle kernel paging request at virtual address fffffffe
pgd = bb25c000
[fffffffe] *pgd=3bfde821, *pte=00000000, *ppte=00000000
Internal error: Oops: 80000007 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 62 Comm: startpar Not tainted 3.16.0-rc3-00062-gd92a333-dirty #5
task: bb230b80 ti: bb256000 task.ti: bb256000
PC is at 0xfffffffe
LR is at iwmmxt_task_copy+0x44/0x4c
pc : [<fffffffe>] lr : [<800130ac>] psr: 40000033
sp : bb257de8 ip : 00000013 fp : bb257ea4
r10: bb256000 r9 : fffffdfe r8 : 76e898e6
r7 : bb257ec8 r6 : bb256000 r5 : 7ea12760 r4 : 000000a0
r3 : ffffffff r2 : 00000003 r1 : bb257df8 r0 : 00000000
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 10c5387d Table: 3b25c019 DAC: 00000015
Process startpar (pid: 62, stack limit = 0xbb256248)
This patch fixes the issue by moving concan_{save,dump,load} into separate
code sections and make iwmmxt_task_enable() call them in the same way the
other functions use concan_ symbols. The test for valid ownership is moved
to concan_save and is safe for the other user of it, iwmmxt_task_disable().
The register collision is also resolved by moving concan_ symbols as
{inc,dec}_preempt_count are now local to iwmmxt_task_enable().
Fixes: 431a84b1a4 ("ARM: 8034/1: Disable preemption in iwmmxt_task_enable()")
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Huawei's usage of the subclass and protocol fields is not 100%
clear to us, but there appears to be a very strict system.
A device with the "shared" device ID 12d1:1506 and this NCM
function was recently reported (showing only default altsetting):
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 3
bInterfaceProtocol 22
iInterface 8 CDC Network Control Model (NCM)
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 06 24 1a 00 01 1f
** UNRECOGNIZED: 0c 24 1b 00 01 00 04 10 14 dc 05 20
** UNRECOGNIZED: 0d 24 0f 0a 0f 00 00 00 ea 05 03 00 01
** UNRECOGNIZED: 05 24 06 01 01
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 9
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
If "newmtu * 2 + 4" is too large then it can cause an integer overflow
leading to memory corruption. Eric Dumazet suggests that 65534 is a
reasonable upper limit.
Btw, "newmtu" is not allowed to be a negative number because of the
check in dev_set_mtu(), so that's ok.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up the CMA region, we must ensure that the old section
mappings are flushed from the TLB before replacing them with page
tables, otherwise we can suffer from mismatched aliases if the CPU
speculatively prefetches from these mappings at an inopportune time.
A mismatched alias can occur when the TLB contains a section mapping,
but a subsequent prefetch causes it to load a page table mapping,
resulting in the possibility of the TLB containing two matching
mappings for the same virtual address region.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[linux-3.16-rc5/drivers/ata/pata_ep93xx.c:929]: (style) Checking if unsigned
variable 'irq' is less than zero.
Source code is
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
but
unsigned int irq;
$ fgrep platform_get_irq `find . -name \*.h -print`
./include/linux/platform_device.h:extern int platform_get_irq(struct
platform_device *, unsigned int);
Now using "int" type instead of "unsigned int" for "irq" variable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80401
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 568f194e8b ("net: ppp: use
sk_unattached_filter api") inadvertently changed the logic when setting
PPP pass and active filters. This applies to both the generic PPP subsystem
implemented by drivers/net/ppp/ppp_generic.c and the ISDN PPP subsystem
implemented by drivers/isdn/i4l/isdn_ppp.c. The original code in ppp_ioctl()
(or isdn_ppp_ioctl(), resp.) handling PPPIOCSPASS and PPPIOCSACTIVE allowed to
remove a pass/active filter previously set by using a filter of length zero.
However, with the new code this is not possible anymore as this case is not
explicitly checked for, which leads to passing NULL as a filter to
sk_unattached_filter_create(). This results in returning EINVAL to the caller.
Additionally, the variables ppp->pass_filter and ppp->active_filter (or
is->pass_filter and is->active_filter, resp.) are not reset to NULL, although
the filters they point to may have been destroyed by
sk_unattached_filter_destroy(), so in this EINVAL case dangling pointers are
left behind (provided the pointers were previously non-NULL).
This patch corrects both problems by checking whether the filter passed is
empty or non-empty, and prevents sk_unattached_filter_create() from being
called in the first case. Moreover, the pointers are always reset to NULL
as soon as sk_unattached_filter_destroy() returns.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a regression introduced by commit 35f6f45 ("net/mlx4_en: Don't use
irq_affinity_notifier to track changes in IRQ affinity map").
When core is started in legacy EQ's (number of IRQ's < rx rings), cq->irq_desc
was NULL. This caused a kernel crash under heavy traffic - when having more
than rx NAPI budget completions.
Fixed to have it set for both EQ modes.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing cleans up the objects created by
vnet_new(), they are completely leaked.
vnet_exit(), after doing the vio_unregister_driver() to clean
up ports, should call a helper function that iterates over vnet_list
and cleans up those objects. This includes unregister_netdevice()
as well as free_netdev().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reviewed-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet port on my ASUS A88X Pro mainboard stopped working
several times a day, with messages like these in dmesg:
AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x001e address=0x0000000000003000 flags=0x0050]
Searching the web for these messages led me to similar reports about
different hardware supported by r8169, and eventually to commits
3ced8c955e ('r8169: enforce RX_MULTI_EN
for the 8168f.') and eb2dc35d99 ('r8169:
RxConfig hack for the 8168evl'). So I tried this change, and it fixes
the problem for me.
Signed-off-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/nf_tables fixes
The following patchset contains nf_tables fixes, they are:
1) Fix wrong transaction handling when the table flags are not
modified.
2) Fix missing rcu read_lock section in the netlink dump path, which
is not protected by the nfnl_lock.
3) Set NLM_F_DUMP_INTR in the netlink dump path to indicate
interferences with updates.
4) Fix 64 bits chain counters when they are retrieved from a 32 bits
arch, from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug that was introduced by my GRE-GRO patch
(bf5a755f5e net-gre-gro: Add GRE
support to the GRO stack) that breaks the forwarding path
because various GSO related fields were not set. The bug will
cause on the egress path either the GSO code to fail, or a
GRE-TSO capable (NETIF_F_GSO_GRE) NICs to choke. The following
fix has been tested for both cases.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unnecessary to excessively spam the kernel log anytime the BTS buffer
cannot be allocated, so make this allocation __GFP_NOWARN.
The user probably will want to at least find some artifact that the
allocation has failed in the past, probably due to fragmentation because
of its large size, when it's not allocated at bootstrap. Thus, add a
WARN_ONCE() so something is left behind for them to understand why perf
commnads that require PEBS is not working properly.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1406301600460.26302@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With -cpu host, KVM reports LBR and extra_regs support, if the host has
support.
When the guest perf driver tries to access LBR or extra_regs MSR,
it #GPs all MSR accesses,since KVM doesn't handle LBR and extra_regs support.
So check the related MSRs access right once at initialization time to avoid
the error access at runtime.
For reproducing the issue, please build the kernel with CONFIG_KVM_INTEL = y
(for host kernel).
And CONFIG_PARAVIRT = n and CONFIG_KVM_GUEST = n (for guest kernel).
Start the guest with -cpu host.
Run perf record with --branch-any or --branch-filter in guest to trigger LBR
Run perf stat offcore events (E.g. LLC-loads/LLC-load-misses ...) in guest to
trigger offcore_rsp #GP
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maria Dimakopoulou <maria.n.dimakopoulou@gmail.com>
Cc: Mark Davies <junk@eslaf.co.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yan, Zheng <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1405365957-20202-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The fixup of the inline assembly to restore the floating-point-control
register needs to check for instruction address *after* the lfcp
instruction as the specification and data exceptions are suppresssing.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve device probing process for zcrypt adapters to
transmit service request during registration process.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The PSW mask check of the PTRACE_POKEUSR_AREA command is incorrect.
The PSW_MASK_USER define contains the PSW_MASK_ASC bits, the ptrace
interface accepts all combinations for the address-space-control
bits. To protect the kernel space the PSW mask check in ptrace needs
to reject the address-space-control bit combination for home space.
Fixes CVE-2014-3534
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MSI irqchip in s390 has its own mask and unmask MSI irq
functions, zpci_enable_irq() and zpci_disable_irq().
They mask and unmask MSI irq in standard ways, no arch
special. MSI driver provides two global standard functions
mask_msi_irq() and unmask_msi_irq(). Local zpci_enable_irq()
and zpci_disable_irq() are almost the same as the standard
two. the difference is local mask/unmask functions
read the mask status before mask and unmask everytime.
Then change the value and rewrite to hardware. In standard
functions, save the mask status after mask and unmask msi
irq, and use the cached status to change the mask status.
When we mask or unmask a MSI irq, we always cache its
mask status except we know need not to cache it, like in
pci_msi_shutdown. So use the standard functions to replace
the local is safe.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
[sebott: fixed inverted function pointers]
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The size detection for 3270 terminals with the read-partition command is
broken. The raw3270_reset_device_cb function clears the init_data array,
but if raw3270_writesf_readpart has been called the read-partition command
is queued which needs the init_data array. In this case the size detection
will fail and the invalid command does funny things to the terminal.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Inlined uaccess functions require the mvcos facility (bit 27), not the tod
clock steering facility (bit 28) for z10 and newer machines.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Xtensa fixes for 3.16:
- resolve FIXMEs in double exception handler for window overflow. This
fix makes native building of linux on xtensa host possible;
- fix sysmem region removal issue introduced in 3.15.
commit 8f4e0a1868 ("IPVS netns exit causes crash in conntrack")
added second ip_vs_conn_drop_conntrack call instead of just adding
the needed check. As result, the first call still can cause
crash on netns exit. Remove it.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
The gpio-rcar driver has no IRQ domain OF xlate function and thus
ignores IRQ flags specified in DT. Fix this by using the two-cell xlate
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
st_gpio_irqmux_handler() reads the status register to find out
which banks inside the controller have pending IRQs.
For each banks having pending IRQs, it calls the corresponding handler.
Problem is that current code restricts the number of possible banks inside the
controller to ST_GPIO_PINS_PER_BANK. This define represents the number of pins
inside a bank, so it shouldn't be used here.
On STiH407, PIO_FRONT0 controller has 10 banks, so IRQs pending in the two
last banks (PIO18 & PIO19) aren't handled.
This patch replace ST_GPIO_PINS_PER_BANK by the number of banks inside the
controller.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> #v3.15+
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
libata-eh.c should handle AMNF error condition (error byte bit 0,
usually code 0x01) in libata-eh.c along with UNC as a media error so
SCSI stack can handle it properly (translation code 0x01 is already
present in libata-scsi.c) but was never passed down due to lack of
handling in EH.
While using linux-based machine (AMD 6550M-based notebook, PCI IDs for the
controller are 1022:7801 subsys 1025:059d) and ddrescue to salvage data
from failing hard drive (WD7500BPVT 2.5" 750G SATA2), I've found that pure
AMNF 0x01 error code generates generic "device error" that is retried
several times by SCSI stack instead of "media error" that is passed up to
software.
So we may assume deprecated AMNF error code is surely not dead yet, and
it's better for it to be handled properly. As we may see it is used by
modern enough devices, and used properly: drive returned AMNF only when IDs
for track cannot be read completely due to dying head or positioning,
otherwise it returned UNC(orrectables).
Not handling it causes wrong generic error code ("device error") reporting
down the stack, can damage failing drives further because of excessive
retries, and slows salvaging down a lot. Also, there is handling code in
libata-scsi.c for 0x01 AMNF error already.
https://bugzilla.kernel.org/show_bug.cgi?id=80031
tj: Shortened $SUBJ and moved its content to the first paragraph.
Signed-off-by: Alexey Asemov <alex@alex-at.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acer Aspire needs to be added to nomux blacklist, otherwise the touchpad
misbehaves rather randomly.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Detected symbol rate value was returned too small.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Inversion ON was reported as inversion OFF and vice versa.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
FEC AUTO is valid for PSK-8 modulation too. Add it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only supported modulation for DVB-S is QPSK. Modulation parameter
contains invalid value for DVB-S on some cases, which leads driver
refusing tuning attempt. Due to that, hard code modulation to QPSK
in case of DVB-S.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2
("libata/ahci: accommodate tag ordered controllers"). The reason is
that the ata controller on this SoC only implement a queue depth of
16. When issuing the commands in tag order, all the commands in tag
16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata
malfunction. It makes no senses to use a 32 queue in software while
the hardware has less queue depth. So consider the queue depth
implemented by the hardware when requesting a command tag.
Fixes: 8a4aeec8d2 ("libata/ahci: accommodate tag ordered controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
On OMAP SOCs using PL310 controllers, power_ctrl register is not
accessible from non-secure software even on PL310 versions which
support it. The secure code takes care of setting it up correctly
and power transitions are proven on these devices.
For example, AM437x has L2C-310 version r3p3 and ROM code on that
device does not support writing to L2C-310 power control register.
The L2C driver, however, tries writing to this register for all
revisions >= r3p0.
This leads to a warning dump on boot which leads most users to believe
that L2 cache is non-functional.
Since the problem is understood, and cannot be addressed through
software, replace the warning with a pr_info() while maintaining the
WARN_ON() for other truly unexpected scenarios.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch provides the compat BLKZEROOUT ioctl. The argument is a pointer
to two uint64_t values, so there is no need to translate it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.7+
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use generic u64_stats_sync infrastructure to get proper 64bit stats,
even on 32bit arches, at no extra cost for 64bit arches.
Without this fix, 32bit arches can have some wrong counters at the time
the carry is propagated into upper word.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
An updater may interfer with the dumping of any of the object lists.
Fix this by using a per-net generation counter and use the
nl_dump_check_consistent() interface so the NLM_F_DUMP_INTR flag is set
to notify userspace that it has to restart the dump since an updater
has interfered.
This patch also replaces the existing consistency checking code in the
rule dumping path since it is broken. Basically, the value that the
dump callback returns is not propagated to userspace via
netlink_dump_start().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The dump operation through netlink is not protected by the nfnl_lock.
Thus, a reader process can be dumping any of the existing object
lists while another process can be updating the list content.
This patch resolves this situation by protecting all the object
lists with RCU in the netlink dump path which is the reader side.
The updater path is already protected via nfnl_lock, so use list
manipulation RCU-safe operations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While a queue is being destroyed, all the blkgs are destroyed and its
->root_blkg pointer is set to NULL. If someone else starts to drain
while the queue is in this state, the following oops happens.
NULL pointer dereference at 0000000000000028
IP: [<ffffffff8144e944>] blk_throtl_drain+0x84/0x230
PGD e4a1067 PUD b773067 PMD 0
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in: cfq_iosched(-) [last unloaded: cfq_iosched]
CPU: 1 PID: 537 Comm: bash Not tainted 3.16.0-rc3-work+ #2
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task: ffff88000e222250 ti: ffff88000efd4000 task.ti: ffff88000efd4000
RIP: 0010:[<ffffffff8144e944>] [<ffffffff8144e944>] blk_throtl_drain+0x84/0x230
RSP: 0018:ffff88000efd7bf0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff880015091450 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88000efd7c10 R08: 0000000000000000 R09: 0000000000000001
R10: ffff88000e222250 R11: 0000000000000000 R12: ffff880015091450
R13: ffff880015092e00 R14: ffff880015091d70 R15: ffff88001508fc28
FS: 00007f1332650740(0000) GS:ffff88001fa80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000028 CR3: 0000000009446000 CR4: 00000000000006e0
Stack:
ffffffff8144e8f6 ffff880015091450 0000000000000000 ffff880015091d80
ffff88000efd7c28 ffffffff8144ae2f ffff880015091450 ffff88000efd7c58
ffffffff81427641 ffff880015091450 ffffffff82401f00 ffff880015091450
Call Trace:
[<ffffffff8144ae2f>] blkcg_drain_queue+0x1f/0x60
[<ffffffff81427641>] __blk_drain_queue+0x71/0x180
[<ffffffff81429b3e>] blk_queue_bypass_start+0x6e/0xb0
[<ffffffff814498b8>] blkcg_deactivate_policy+0x38/0x120
[<ffffffff8144ec44>] blk_throtl_exit+0x34/0x50
[<ffffffff8144aea5>] blkcg_exit_queue+0x35/0x40
[<ffffffff8142d476>] blk_release_queue+0x26/0xd0
[<ffffffff81454968>] kobject_cleanup+0x38/0x70
[<ffffffff81454848>] kobject_put+0x28/0x60
[<ffffffff81427505>] blk_put_queue+0x15/0x20
[<ffffffff817d07bb>] scsi_device_dev_release_usercontext+0x16b/0x1c0
[<ffffffff810bc339>] execute_in_process_context+0x89/0xa0
[<ffffffff817d064c>] scsi_device_dev_release+0x1c/0x20
[<ffffffff817930e2>] device_release+0x32/0xa0
[<ffffffff81454968>] kobject_cleanup+0x38/0x70
[<ffffffff81454848>] kobject_put+0x28/0x60
[<ffffffff817934d7>] put_device+0x17/0x20
[<ffffffff817d11b9>] __scsi_remove_device+0xa9/0xe0
[<ffffffff817d121b>] scsi_remove_device+0x2b/0x40
[<ffffffff817d1257>] sdev_store_delete+0x27/0x30
[<ffffffff81792ca8>] dev_attr_store+0x18/0x30
[<ffffffff8126f75e>] sysfs_kf_write+0x3e/0x50
[<ffffffff8126ea87>] kernfs_fop_write+0xe7/0x170
[<ffffffff811f5e9f>] vfs_write+0xaf/0x1d0
[<ffffffff811f69bd>] SyS_write+0x4d/0xc0
[<ffffffff81d24692>] system_call_fastpath+0x16/0x1b
776687bce4 ("block, blk-mq: draining can't be skipped even if
bypass_depth was non-zero") made it easier to trigger this bug by
making blk_queue_bypass_start() drain even when it loses the first
bypass test to blk_cleanup_queue(); however, the bug has always been
there even before the commit as blk_queue_bypass_start() could race
against queue destruction, win the initial bypass test but perform the
actual draining after blk_cleanup_queue() already destroyed all blkgs.
Fix it by skippping calling into policy draining if all the blkgs are
already gone.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Shirish Pargaonkar <spargaonkar@suse.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Jet Chen <jet.chen@intel.com>
Cc: stable@vger.kernel.org
Tested-by: Shirish Pargaonkar <spargaonkar@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since linux kernel 3.13, kthread_run() internally uses
wait_for_completion_killable(). We sometimes may use kthread_run()
while we still have a signal pending, which we used to kick our threads
out of potentially blocking network functions, causing kthread_run() to
mistake that as a new fatal signal and fail.
Fix: flush_signals() before kthread_run().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no inherent reason why the last put of a tag structure must be
the one for the Scsi_Host, as device model objects can be held for
arbitrary periods. Merge blk_free_tags and __blk_free_tags into a single
funtion that just release a references and get rid of the BUG() when the
host reference wasn't the last.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Patch queue for 3.16 - 2014-07-08
A few bug fixes to make 3.16 work well with KVM on PowerPC:
- Fix ppc32 module builds
- Fix Little Endian hosts
- Fix Book3S HV HPTE lookup with huge pages in guest
- Fix BookE lock leak
With commit b6b8a1451f that introduced
vmx_check_nested_events, checks for injectable interrupts happen
at different points in time for L1 and L2 that could potentially
cause a race. The regression occurs because KVM_REQ_EVENT is always
set when nested_run_pending is set even if there's no pending interrupt.
Consequently, there could be a small window when check_nested_events
returns without exiting to L1, but an interrupt comes through soon
after and it incorrectly, gets injected to L2 by inject_pending_event
Fix this by adding a call to check for nested events too when a check
for injectable interrupt returns true
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In commit b59d9d26b we introduced implicit byte swaps for RTAS calls.
Unfortunately we messed up and didn't swizzle return values properly.
Also the old approach wasn't "sparse" compatible - we were randomly
reading __be32 values on an LE system.
Let's just do all of the swizzling explicitly with byte swaps right
where values get used. That way we can at least catch bugs using sparse.
This patch fixes XICS RTAS emulation on little endian hosts for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
This reverts commit 277d916fc2 as it was
at least breaking iwlwifi by setting the IEEE80211_TX_CTL_NO_PS_BUFFER
flag in all kinds of interface modes, not only for AP mode where it is
appropriate.
To avoid reintroducing the original problem, explicitly check for probe
request frames in the multicast buffering code.
Cc: stable@vger.kernel.org
Fixes: 277d916fc2 ("mac80211: move "bufferable MMPDU" check to fix AP mode scan")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We switched to ABIv2 on Little Endian systems now which gets rid of the
dotted function names. Branch to the actual functions when we see such
a system.
Signed-off-by: Alexander Graf <agraf@suse.de>
Both kvmppc_hv_entry_trampoline and kvmppc_entry_trampoline are
assembly functions that are exported to modules and also require
a valid r2.
As such we need to use _GLOBAL_TOC so we provide a global entry
point that establishes the TOC (r2).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When the audio encoding is changed the driver calls hdpvr_set_audio
with the current opt->audio_input value. However, that should have
been opt->audio_input + 1. So changing the audio encoding inadvertently
changes the input as well. This bug has always been there.
The second bug was introduced in kernel 3.10 and that broke the
default_audio_input module option handling: the audio encoding was
never switched to AC3 if default_audio_input was set to 2 (SPDIF input).
In addition, since starting with 3.10 the audio encoding is always set
at the start the first bug now always happens when the driver is loaded.
In the past this bug would only surface if the user would change the
audio encoding after the driver was loaded.
Also fixes a small trivial typo (bufffer -> buffer).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Scott Doty <scott@corp.sonic.net>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tuner ID set into EEPROM is wrong in some cases, which causes driver
to select wrong tuner profile. That leads device non-working. Fix
issue by overriding known bad tuner IDs with suitable default value.
Thanks to MX-NET Telekomunikace s.r.o. for providing non-working
DTV stick, that I could fix the bug!
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Skip transaction handling for table updates with no changes in
the flags. This fixes a crash when passing the table flag with all
bits unset.
Reported-by: Ana Rey <anarey@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The SPI check introduced in ea9884b3ac
was intended for IPComp SAs but actually prevented AH SAs from getting
installed (depending on the SPI).
Fixes: ea9884b3ac ("xfrm: check user specified spi for IPComp")
Cc: Fan Du <fan.du@windriver.com>
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit ac5a8ee8 started using _GLOBAL_TOC on ppc32 code. Unfortunately it's only
defined for 64bit targets though. Define it for ppc32 as well, fixing the build
breakage that commit introduced.
Signed-off-by: Alexander Graf <agraf@suse.de>
xfrm_lookup must return a dst_entry with a refcount for the caller.
Git commit 1a1ccc96ab ("xfrm: Remove caching of xfrm_policy_sk_bundles")
removed this refcount for the socket policy case accidentally.
This patch restores it and sets DST_NOCACHE flag to make sure
that the dst_entry is freed when the refcount becomes null.
Fixes: 1a1ccc96ab ("xfrm: Remove caching of xfrm_policy_sk_bundles")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With guests supporting Multiple page size per segment (MPSS),
hpte_page_size returns the actual page size used. Add a new function to
return base page size and use that to compare against the the page size
calculated from SLB. Without this patch a hpte lookup can fail since
we are comparing wrong page size in kvmppc_hv_find_lock_hpte.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The patch 08c9a188d0
kvm: powerpc: use caching attributes as per linux pte
do not handle properly the error case, letting mmu_lock locked. The lock
will further generate a RCU stall from kvmppc_e500_emul_tlbwe() caller.
In case of an error go to out label.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The saa7134 driver uses core-locking, so there is no longer any need
to use the ioctl op instead of the unlocked_ioctl op. This change
was forgotten for the saa7134-empress.c, so fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
First 8 bytes belonging to firmware image were hard-coded and uploaded
by the driver mistakenly. Introduce new corrected firmware file and
remove those 8 bytes from the driver.
New firmware image could be extracted from the PCTV 292e driver CD
using following command:
$ dd if=/TVC 6.4.8/Driver/PCTV Empia/emOEM.sys ibs=1 skip=1089408 count=2728 of=dvb-demod-si2168-02.fw
$ md5sum dvb-demod-si2168-02.fw
d8da7ff67cd56cd8aa4e101aea45e052 dvb-demod-si2168-02.fw
$ sudo cp dvb-demod-si2168-02.fw /lib/firmware/
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix following warnings:
si2157_cmd_execute() warn: add some parenthesis here?
si2157_cmd_execute() warn: maybe use && instead of &
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix following warnings:
si2168_cmd_execute() warn: add some parenthesis here?
si2168_cmd_execute() warn: maybe use && instead of &
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The OMAP4 camera support depends on I2C and VIDEO_V4L2, both
of which can be loadable modules. This causes build failures
if we want the camera driver to be built-in.
This can be solved by turning the option into "tristate",
which unfortunately causes another problem, because the
driver incorrectly calls a platform-internal interface
for omap4_ctrl_pad_readl/omap4_ctrl_pad_writel.
Instead, this patch just forbids the invalid configurations
and ensures that the driver can only be built if all its
dependencies are built-in.
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the hopes that people run new kernels on their devices, let's add a
warning message asking users to have their DTS file fixed.
The goal is that by Linux 4.0 we will be able to remove support for the
bogus version of our touchscreen's DTS.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Historically we dealt with touch_max equals to 2 differently from
other MT devices. Now we use input_mt_*() to process all MT events,
as long as touch_max is greater than 1. So, there is no need to
take (touch_max == 2) as a special case any more.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When sysmem reservation occurs exactly at the end of an existing block
that block is deleted, because it is incorrectly included in the range
of memblocks to remove. Fix that by skipping such block.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There are two FIXMEs in the double exception handler 'for the extremely
unlikely case'. This case gets hit by gcc during kernel build once in
a few hours, resulting in an unrecoverable exception condition.
Provide missing fixup routine to handle this case. Double exception
literals now need 8 more bytes, add them to the linker script.
Also replace bbsi instructions with bbsi.l as we're branching depending
on 8th and 7th LSB-based bits of exception address.
This may be tested by adding the explicit DTLB invalidation to window
overflow handlers, like the following:
--- a/arch/xtensa/kernel/vectors.S
+++ b/arch/xtensa/kernel/vectors.S
@@ -592,6 +592,14 @@ ENDPROC(_WindowUnderflow4)
ENTRY_ALIGN64(_WindowOverflow8)
s32e a0, a9, -16
+ bbsi.l a9, 31, 1f
+ rsr a0, ccount
+ bbsi.l a0, 4, 1f
+ pdtlb a0, a9
+ idtlb a0
+ movi a0, 9
+ idtlb a0
+1:
l32e a0, a1, -12
s32e a2, a9, -8
s32e a1, a9, -12
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The patch 3e374919b3 is supposed to fix the
problem where kmem_cache_create incorrectly reports duplicate cache name
and fails. The problem is described in the header of that patch.
However, the patch doesn't really fix the problem because of these
reasons:
* the logic to test for debugging is reversed. It was intended to perform
the check only if slub debugging is enabled (which implies that caches
with the same parameters are not merged). Therefore, there should be
#if !defined(CONFIG_SLUB) || defined(CONFIG_SLUB_DEBUG_ON)
The current code has the condition reversed and performs the test if
debugging is disabled.
* slub debugging may be enabled or disabled based on kernel command line,
CONFIG_SLUB_DEBUG_ON is just the default settings. Therefore the test
based on definition of CONFIG_SLUB_DEBUG_ON is unreliable.
This patch fixes the problem by removing the test
"!defined(CONFIG_SLUB_DEBUG_ON)". Therefore, duplicate names are never
checked if the SLUB allocator is used.
Note to stable kernel maintainers: when backporint this patch, please
backport also the patch 3e374919b3.
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Pekka Enberg <penberg@kernel.org>
The SC1200 is a SoC based on the Geode GX1 32-bit x86 processor, so
its drivers are only needed on this architecture, except for build
testing purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As far as I know, the CS5520 and CS5530 chipsets were only used with
32-bit x86 Geode processors, so I think their drivers are only needed
on this architecture, except for build testing purpose.
While we're here, simplify the dependencies for the CS5535 driver.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On m68k, host->get_lock is used to both lock and register the interrupt
that the IDE host shares with other device drivers. Registering the
IDE interrupt handler in ide-probe.c results in duplicating the
interrupt registered (once via host->get lock, and also via init_irq()),
and may result in IDE accepting interrupts even when another driver has
locked the interrupt hardware. This opens the whole locking scheme up
to races.
host->get_lock is set on m68k only, so other drivers' behaviour is not
changed.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-ide@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-04 15:58:31 -05:00
244 changed files with 1953 additions and 910 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.