Pull watchdog fixes from Wim Van Sebroeck:
"This will fix a deadlock on the ts72xx_wdt driver, fix bitmasks in the
kempld_wdt driver and fix a section mismatch in the sunxi_wdt driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sunxi: Fix section mismatch
watchdog: kempld_wdt: Fix bit mask definition
watchdog: ts72xx_wdt: locking bug in ioctl
This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.
WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
STAGE_CFG bits are defined as [5:4] bits. However, '(((x) & 0x30) << 4)'
handles [9:8] bits. Thus, it should be fixed in order to handle
[5:4] bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Calling the WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS and twice will cause a
interruptible deadlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull ARM SoC fixes from Olof Johansson:
"A small batch of fixes this week, mostly OMAP related. Nothing stands
out as particularly controversial.
Also a fix for a 3.12-rc1 timer regression for Exynos platforms,
including the Chromebooks"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.
[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)
THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
[olof: Changed subject, added comment, elaborated on commit message]
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few fixes for omap3 related hangs and errors that people have
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
* tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull parisc fixes from Helge Deller:
"This patchset includes a bugfix to prevent a kernel crash when memory
in page zero is accessed by the kernel itself, e.g. via
probe_kernel_read().
Furthermore we now export flush_cache_page() which is needed
(indirectly) by the lustre filesystem. The other patches remove
unused functions and optimizes the page fault handler to only evaluate
variables if needed, which again protects against possible kernel
crashes"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: let probe_kernel_read() capture access to page zero
parisc: optimize variable initialization in do_page_fault
parisc: fix interruption handler to respect pagefault_disable()
parisc: mark parisc_terminate() noreturn and cold.
parisc: remove unused syscall_ipi() function.
parisc: kill SMP single function call interrupt
parisc: Export flush_cache_page() (needed by lustre)
Pull slave-dmaengine fixes from Vinod Koul:
"Another week, time to send another fixes request taking time out of
extended weekend for the festivities in this part of the world.
We have two fixes from Sergei for rcar driver and one fixing memory
leak of edma driver by Geyslan"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: edma.c: remove edma_desc leakage
rcar-hpbdma: add parameter to set_slave() method
rcar-hpbdma: remove shdma_free_irq() calls
The attached change defers the initialization of the variables tsk, mm
and flags until they are needed. As a result, the code won't crash if a
kernel probe is done with a corrupt context and the code will be better
optimized.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Running an "echo t > /proc/sysrq-trigger" crashes the parisc kernel. The
problem is, that in print_worker_info() we try to read the workqueue info via
the probe_kernel_read() functions which use pagefault_disable() to avoid
crashes like this:
probe_kernel_read(&pwq, &worker->current_pwq, sizeof(pwq));
probe_kernel_read(&wq, &pwq->wq, sizeof(wq));
probe_kernel_read(name, wq->name, sizeof(name) - 1);
The problem here is, that the first probe_kernel_read(&pwq) might return zero
in pwq and as such the following probe_kernel_reads() try to access contents of
the page zero which is read protected and generate a kernel segfault.
With this patch we fix the interruption handler to call parisc_terminate()
directly only if pagefault_disable() was not called (in which case
preempt_count()==0). Otherwise we hand over to the pagefault handler which
will try to look up the faulting address in the fixup tables.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 9a46ad6d6d "smp: make smp_call_function_many() use logic
similar to smp_call_function_single()" has unified the way to handle
single and multiple cross-CPU function calls. Now only one interrupt
is needed for architecture specific code to support generic SMP function
call interfaces, so kill the redundant single function call interrupt.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Olga reported that file descriptors opened with O_PATH do not work with
fstatfs(), found during further development of ksh93's thread support.
There is no reason to not allow O_PATH file descriptors here (fstatfs is
very much a path operation), so use "fdget_raw()". See commit
55815f7014 ("vfs: make O_PATH file descriptors usable for 'fstat()'")
for a very similar issue reported for fstat() by the same team.
Reported-and-tested-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # O_PATH introduced in 3.0+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ext4 bugfixes from Ted Ts'o:
"A bug fix and performance regression fix for ext4"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix memory leak in xattr
ext4: fix performance regression in writeback of random writes
Pull btrfs fixes from Chris Mason:
"We've got more bug fixes in my for-linus branch:
One of these fixes another corner of the compression oops from last
time. Miao nailed down some problems with concurrent snapshot
deletion and drive balancing.
I kept out one of his patches for more testing, but these are all
stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix oops caused by the space balance and dead roots
Btrfs: insert orphan roots into fs radix tree
Btrfs: limit delalloc pages outside of find_delalloc_range
Btrfs: use right root when checking for hash collision
Pull sound fixes from Takashi Iwai:
"All stable fixes except for a trivial headset mic fixup: the removal
of bogus frame checks in snd-usb-usx2y driver that have regressed in
the recent kernel versions, the HD-audio HDMI channel map fix, and a
few HD-audio device-specific fixes"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Sony VAIO Pro 13 (haswell) now has a working headset jack
ALSA: hda - Add a headset mic model for ALC269 and friends
ALSA: hda - Fix microphone for Sony VAIO Pro 13 (Haswell model)
ALSA: hda - Add fixup for ASUS N56VZ
ALSA: hda - hdmi: Fix channel map switch not taking effect
ALSA: hda - Fix mono speakers and headset mic on Dell Vostro 5470
ALSA: snd-usb-usx2y: remove bogus frame checks
Pull i2c fixes from Wolfram Sang:
"We had various reports of problems with deferred probing in the I2C
subsystem, so this pull requst is a little bigger than usual.
Most issues should be addressed now so devices will be found
correctly. A few ususal driver bugfixes are in here, too"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-mux-pinctrl: use deferred probe when adapter not found
i2c: i2c-arb-gpio-challenge: use deferred probe when adapter not found
i2c: i2c-mux-gpio: use deferred probing
i2c: i2c-mux-gpio: don't ignore of_get_named_gpio errors
i2c: omap: Clear ARDY bit twice
i2c: Not all adapters have a parent
i2c: i2c-stu300: replace platform_driver_probe to support deferred probing
i2c: i2c-mxs: replace platform_driver_probe to support deferred probing
i2c: i2c-imx: replace platform_driver_probe to support deferred probing
i2c: i2c-designware-platdrv: replace platform_driver_probe to support deferred probing
If we take the 2nd retry path in ext4_expand_extra_isize_ea, we
potentionally return from the function without having freed these
allocations. If we don't do the return, we over-write the previous
allocation pointers, so we leak either way.
Spotted with Coverity.
[ Fixed by tytso to set is and bs to NULL after freeing these
pointers, in case in the retry loop we later end up triggering an
error causing a jump to cleanup, at which point we could have a double
free bug. -- Ted ]
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Cc: stable@vger.kernel.org
Pull gcc "asm goto" miscompilation workaround from Ingo Molnar:
"This is the fix for the GCC miscompilation discussed in the following
lkml thread:
[x86] BUG: unable to handle kernel paging request at 00740060
The bug in GCC has been fixed by Jakub and the fix will be part of the
GCC 4.8.2 release expected to be released next week - so the quirk's
version test checks for <= 4.8.1.
The quirk is only added to compiler-gcc4.h and not to the higher level
compiler.h because all asm goto uses are behind a feature check"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compiler/gcc4: Add quirk for 'asm goto' miscompilation bug
Pull x86 fixes from Ingo Molnar:
"A build fix and a reboot quirk"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/reboot: Add reboot quirk for Dell Latitude E5410
x86, build, pci: Fix PCI_MSI build on !SMP
Pull ARC fix from Vineet Gupta:
"Fix for broken gdb 'jump'"
* tag 'arc-fixes-for-3.12-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Ignore ptrace SETREGSET request for synthetic register "stop_pc"
ARCompact TRAP_S insn used for breakpoints, commits before exception is
taken (updating architectural PC). So ptregs->ret contains next-PC and
not the breakpoint PC itself. This is different from other restartable
exceptions such as TLB Miss where ptregs->ret has exact faulting PC.
gdb needs to know exact-PC hence ARC ptrace GETREGSET provides for
@stop_pc which returns ptregs->ret vs. EFA depending on the
situation.
However, writing stop_pc (SETREGSET request), which updates ptregs->ret
doesn't makes sense stop_pc doesn't always correspond to that reg as
described above.
This was not an issue so far since user_regs->ret / user_regs->stop_pc
had same value and both writing to ptregs->ret was OK, needless, but NOT
broken, hence not observed.
With gdb "jump", they diverge, and user_regs->ret updating ptregs is
overwritten immediately with stop_pc, which this patch fixes.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull MIPS fix from Ralf Baechle:
"Just one fix. The stack protector was loading the value of the canary
instead of its address"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: stack protector: Fix per-task canary switch
Pull drm fixes from Dave Airlie:
"All over the map..
- nouveau:
disable MSI, needs more work, will try again next merge window
- radeon:
audio + uvd regression fixes, dpm fixes, reset fixes
- i915:
the dpms fix might fix your haswell
And one pain in the ass revert, so we have VGA arbitration that when
implemented 4-5 years ago really hoped that GPUs could remove
themselves from arbitration completely once they had a kernel driver.
It seems Intel hw designers decided that was too nice a facility to
allow us to have so they removed it when they went on-die (so since
Ironlake at least). Now Alex Williamson added support for VGA
arbitration for newer GPUs however this now exposes itself to
userspace as requireing arbitration of GPU VGA regions and the X
server gets involved and disables things that it can't handle when VGA
access is possibly required around every operation.
So in order to not break userspace we just reverted things back to the
old known broken status so maybe we can try and design out way out.
Ville also had a patch to use stop machine for the two times Intel
needs to access VGA space, that might be acceptable with some rework,
but for now myself and Daniel agreed to just go back"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (23 commits)
Revert "i915: Update VGA arbiter support for newer devices"
Revert "drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done"
drm/radeon: re-enable sw ACR support on pre-DCE4
drm/radeon/dpm: disable bapm on TN asics
drm/radeon: improve soft reset on CIK
drm/radeon: improve soft reset on SI
drm/radeon/dpm: off by one in si_set_mc_special_registers()
drm/radeon/dpm/btc: off by one in btc_set_mc_special_registers()
drm/radeon: forever loop on error in radeon_do_test_moves()
drm/radeon: fix hw contexts for SUMO2 asics
drm/radeon: fix typo in CP DMA register headers
drm/radeon/dpm: disable multiple UVD states
drm/radeon: use hw generated CTS/N values for audio
drm/radeon: fix N/CTS clock matching for audio
drm/radeon: use 64-bit math to calculate CTS values for audio (v2)
drm/edid: catch kmalloc failure in drm_edid_to_speaker_allocation
Revert "drm/fb-helper: don't sleep for screen unblank when an oops is in progress"
drm/gma500: fix things after get/put page helpers
drm/nouveau/mc: disable msi support by default, it's busted in tons of places
drm/i915: Only apply DPMS to the encoder if enabled
...
Using the headset mic model will cause the headset mic to be labeled
"headset mic" instead of just "mic".
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The external mic showed up with a precense detect of "always present",
essentially disabling the internal mic. Therefore turn off presence
detection for this pin.
Note: The external mic seems not yet working, but an internal mic is
certainly better than no mic at all.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1227093
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 81b5c7bc8d.
Adding drm/i915 into the vga arbiter chain means that X (in a piece of
well-meant paranoia) will do a get/put on the vga decoding around
_every_ accel call down into the ddx. Which results in some nice
performance disasters [1]. This really breaks userspace, by disabling
DRI for everyone, and stops OpenGL from working, this isn't limited
to just the i915 but both the integrated and discrete GPUs on
multi-gpu systems, in other words this causes untold worlds of pain,
Ville tried to come up with a Great Hack to fiddle the required VGA
I/O ops behind everyone's back using stop_machine, but that didn't
really work out [2]. Given that we're fairly late in the -rc stage for
such games let's just revert this all.
One thing we might want to keep is to delay the disabling of the vga
decoding until the fbdev emulation and the fbcon screen is set up. If
we kill vga mem decoding beforehand fbcon can end up with a white
square in the top-left corner it tried to save from the vga memory for
a seamless transition. And we have bug reports on older platforms
which seem to match these symptoms.
But again that's something to play around with in -next.
References: [1] http://lists.x.org/archives/xorg-devel/2013-September/037763.html
References: [2] http://www.spinics.net/lists/intel-gfx/msg34062.html
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 6e1b4fdad5.
This is part of a revert due to a userspace breakage, better explained in the revert of 1a1a4cbf4906a13c0c377f708df5d94168e7b582.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Regression fixes for audio and UVD, several hang fixes,
some DPM fixes.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: re-enable sw ACR support on pre-DCE4
drm/radeon/dpm: disable bapm on TN asics
drm/radeon: improve soft reset on CIK
drm/radeon: improve soft reset on SI
drm/radeon/dpm: off by one in si_set_mc_special_registers()
drm/radeon/dpm/btc: off by one in btc_set_mc_special_registers()
drm/radeon: forever loop on error in radeon_do_test_moves()
drm/radeon: fix hw contexts for SUMO2 asics
drm/radeon: fix typo in CP DMA register headers
drm/radeon/dpm: disable multiple UVD states
drm/radeon: use hw generated CTS/N values for audio
drm/radeon: fix N/CTS clock matching for audio
drm/radeon: use 64-bit math to calculate CTS values for audio (v2)
drm/edid: catch kmalloc failure in drm_edid_to_speaker_allocation
Free memory allocated to edma_desc when failing to allocate slot.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 4981c4dc19 (DMA: shdma: switch DT mode to
use configuration data from a match table) added a new parameter to set_slave()
method but unfortunately got merged later than commit c4f6c41ba7
(dma: add driver for R-Car HPB-DMAC), so that the HPB-DMAC driver retained the
old prototype which caused this warning:
drivers/dma/sh/rcar-hpbdma.c:485: warning: initialization from incompatible
pointer type
The newly added parameter is used to override DMA slave address from 'struct
hpb_dmae_slave_config', so we have to add the 'slave_addr' field to 'struct
hpb_dmae_chan', conditionally assign it in set_slave() method, and return in
slave_addr() method.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c1c63a14f4 (DMA: shdma: switch to managed
resource allocation) got rid of shdma_free_irq() but unfortunately got merged
later than commit c4f6c41ba7 (dma: add driver for
R-Car HPB-DMAC), so that the HPB-DMAC driver retained the calls and got broken:
drivers/dma/sh/rcar-hpbdma.c: In function `hpb_dmae_alloc_chan_resources':
drivers/dma/sh/rcar-hpbdma.c:435: error: implicit declaration of function
`shdma_free_irq'
Fix this compilation error by removing the remaining shdma_free_irq() calls.
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When doing space balance and subvolume destroy at the same time, we met
the following oops:
kernel BUG at fs/btrfs/relocation.c:2247!
RIP: 0010: [<ffffffffa04cec16>] prepare_to_merge+0x154/0x1f0 [btrfs]
Call Trace:
[<ffffffffa04b5ab7>] relocate_block_group+0x466/0x4e6 [btrfs]
[<ffffffffa04b5c7a>] btrfs_relocate_block_group+0x143/0x275 [btrfs]
[<ffffffffa0495c56>] btrfs_relocate_chunk.isra.27+0x5c/0x5a2 [btrfs]
[<ffffffffa0459871>] ? btrfs_item_key_to_cpu+0x15/0x31 [btrfs]
[<ffffffffa048b46a>] ? btrfs_get_token_64+0x7e/0xcd [btrfs]
[<ffffffffa04a3467>] ? btrfs_tree_read_unlock_blocking+0xb2/0xb7 [btrfs]
[<ffffffffa049907d>] btrfs_balance+0x9c7/0xb6f [btrfs]
[<ffffffffa049ef84>] btrfs_ioctl_balance+0x234/0x2ac [btrfs]
[<ffffffffa04a1e8e>] btrfs_ioctl+0xd87/0x1ef9 [btrfs]
[<ffffffff81122f53>] ? path_openat+0x234/0x4db
[<ffffffff813c3b78>] ? __do_page_fault+0x31d/0x391
[<ffffffff810f8ab6>] ? vma_link+0x74/0x94
[<ffffffff811250f5>] vfs_ioctl+0x1d/0x39
[<ffffffff811258c8>] do_vfs_ioctl+0x32d/0x3e2
[<ffffffff811259d4>] SyS_ioctl+0x57/0x83
[<ffffffff813c3bfa>] ? do_page_fault+0xe/0x10
[<ffffffff813c73c2>] system_call_fastpath+0x16/0x1b
It is because we returned the error number if the reference of the root was 0
when doing space relocation. It was not right here, because though the root
was dead(refs == 0), but the space it held still need be relocated, or we
could not remove the block group. So in this case, we should return the root
no matter it is dead or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Now we don't drop all the deleted snapshots/subvolumes before the space
balance. It means we have to relocate the space which is held by the dead
snapshots/subvolumes. So we must into them into fs radix tree, or we would
forget to commit the change of them when doing transaction commit, and it
would corrupt the metadata.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Liu fixed part of this problem and unfortunately I steered him in slightly the
wrong direction and so didn't completely fix the problem. The problem is we
limit the size of the delalloc range we are looking for to max bytes and then we
try to lock that range. If we fail to lock the pages in that range we will
shrink the max bytes to a single page and re loop. However if our first page is
inside of the delalloc range then we will end up limiting the end of the range
to a period before our first page. This is illustrated below
[0 -------- delalloc range --------- 256mb]
[page]
So find_delalloc_range will return with delalloc_start as 0 and end as 128mb,
and then we will notice that delalloc_start < *start and adjust it up, but not
adjust delalloc_end up, so things go sideways. To fix this we need to not limit
the max bytes in find_delalloc_range, but in find_lock_delalloc_range and that
way we don't end up with this confusion. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
btrfs_rename was using the root of the old dir instead of the root of the new
dir when checking for a hash collision, so if you tried to move a file into a
subvol it would freak out because it would see the file you are trying to move
in its current root. This fixes the bug where this would fail
btrfs subvol create test1
btrfs subvol create test2
mv test1 test2.
Thanks to Chris Murphy for catching this,
Cc: stable@vger.kernel.org
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Commit c0f04d88e4 ("bcache: Fix flushes in writeback mode") was fixing
a reported data corruption bug, but it seems some last minute
refactoring or rebasing introduced a null pointer deref.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Reported-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull hwmon fix from Guenter Roeck:
"Fix root cause of crash/error seen in applesmc driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (applesmc) Always read until end of data
Pull kbuild fix from Michal Marek:
"Here is an ARM Makefile fix that you even acked. After nobody wanted
to take it, it ended up in the kbuild tree"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
arm, kbuild: make "make install" not depend on vmlinux
Pull watchdog fix from Wim Van Sebroeck:
"Make sure that the hpwdt driver will not load auxilary iLO devices"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: hpwdt: Patch to ignore auxilary iLO devices
Useful for locating buggy drivers on kernel oops.
It may add dozens of new lines to boot dmesg. DEBUG_KOBJECT_RELEASE is
hopefully only enabled in debug kernels (like maybe the Fedora rawhide
one, or at developers), so being a bit more verbose is likely ok.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is to prevent hpwdt from loading on any auxilary iLO devices defined
after the initial (or main) iLO device. All auxilary iLO devices will have a
subsystem device ID set to 0x1979 in order for hpwdt to differentiate between
the two types.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull /dev/random changes from Ted Ts'o:
"These patches are designed to enable improvements to /dev/random for
non-x86 platforms, in particular MIPS and ARM"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: allow architectures to optionally define random_get_entropy()
random: run random_int_secret_init() run after all late_initcalls
Pull kvm fixes from Paolo Bonzini:
"Fixes for 3.12-rc5: two old PPC bugs and one new (3.12-rc2) x86 bug"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: ppc: booke: check range page invalidation progress on page setup
KVM: PPC: Book3S HV: Fix typo in saving DSCR
KVM: nVMX: fix shadow on EPT
Pull spi fixes from Mark Brown:
"This is all driver updates, mostly fixes for error handling paths
except for the s3c64xx and hspi fixes for trying to use runtime PM
before it is enabled and the pxa2xx fix for interactions between power
management and interrupt handling"
* tag 'spi-v3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: Fix incorrect error path
spi/hspi: fixup Runtime PM enable timing
spi/s3c64xx: Ensure runtime PM is enabled prior to registration
spi/clps711x: drop clk_put for devm_clk_get in spi_clps711x_probe()
spi: fix return value check in dspi_probe()
spi: mpc512x: fix error return code in mpc512x_psc_spi_do_probe()
spi: clps711x: Don't call kfree() after spi_master_put/spi_unregister_master
spi/pxa2xx: check status register as well to determine if the device is off
Allow architectures which have a disabled get_cycles() function to
provide a random_get_entropy() function which provides a fine-grained,
rapidly changing counter that can be used by the /dev/random driver.
For example, an architecture might have a rapidly changing register
used to control random TLB cache eviction, or DRAM refresh that
doesn't meet the requirements of get_cycles(), but which is good
enough for the needs of the random driver.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
Pull MTD fixes from Brian Norris:
- fix a small memory leak in some new ONFI code
- account for additional odd variations of Micron SPI flash
Acked by David Woodhouse.
* tag 'for-linus-20131008' of git://git.infradead.org/linux-mtd:
mtd: m25p80: Fix 4 byte addressing mode for Micron devices.
mtd: nand: fix memory leak in ONFI extended parameter page
HW ACR support may have issues on some older chips, so
use SW ACR for now until we've tested further.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: Rafał Miłecki <zajec5@gmail.com>
When the MM code is invalidating a range of pages, it calls the KVM
kvm_mmu_notifier_invalidate_range_start() notifier function, which calls
kvm_unmap_hva_range(), which arranges to flush all the TLBs for guest pages.
However, the Linux PTEs for the range being flushed are still valid at
that point. We are not supposed to establish any new references to pages
in the range until the ...range_end() notifier gets called.
The PPC-specific KVM code doesn't get any explicit notification of that;
instead, we are supposed to use mmu_notifier_retry() to test whether we
are or have been inside a range flush notifier pair while we have been
referencing a page.
This patch calls the mmu_notifier_retry() while mapping the guest
page to ensure we are not referencing a page when in range invalidation.
This call is inside a region locked with kvm->mmu_lock, which is the
same lock that is called by the KVM MMU notifier functions, thus
ensuring that no new notification can proceed while we are in the
locked region.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Acked-by: Alexander Graf <agraf@suse.de>
[Backported to 3.12 - Paolo]
Reviewed-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes a typo in the code that saves the guest DSCR (Data Stream
Control Register) into the kvm_vcpu_arch struct on guest exit. The
effect of the typo was that the DSCR value was saved in the wrong place,
so changes to the DSCR by the guest didn't persist across guest exit
and entry, and some host kernel memory got corrupted.
Cc: stable@vger.kernel.org [v3.1+]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
72f857950f broke shadow on EPT. This patch reverts it and fixes PAE
on nEPT (which reverted commit fixed) in other way.
Shadow on EPT is now broken because while L1 builds shadow page table
for L2 (which is PAE while L2 is in real mode) it never loads L2's
GUEST_PDPTR[0-3]. They do not need to be loaded because without nested
virtualization HW does this during guest entry if EPT is disabled,
but in our case L0 emulates L2's vmentry while EPT is enables, so we
cannot rely on vmcs12->guest_pdptr[0-3] to contain up-to-date values
and need to re-read PDPTEs from L2 memory. This is what kvm_set_cr3()
is doing, but by clearing cache bits during L2 vmentry we drop values
that kvm_set_cr3() read from memory.
So why the same code does not work for PAE on nEPT? kvm_set_cr3()
reads pdptes into vcpu->arch.walk_mmu->pdptrs[]. walk_mmu points to
vcpu->arch.nested_mmu while nested guest is running, but ept_load_pdptrs()
uses vcpu->arch.mmu which contain incorrect values. Fix that by using
walk_mmu in ept_(load|save)_pdptrs.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the i2c-parent bus driver is not loaded, returning
-ENODEV will force people to unload and then reload the
module again to get it working.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
of_get_named_gpio could return -E_PROBE_DEFER or another
error code. This error should be passed further instead
of being ignored.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Initially commit cb527ede1b
"i2c-omap: Double clear of ARDY status in IRQ handler"
added a workaround for undocumented errata ProDB0017052.
But then commit 1d7afc9594
"i2c: omap: ack IRQ in parts" refactored code and missed
one of ARDY clearings. So current code violates errata.
It causes often i2c bus timeouts on my Pandaboard.
This patch adds a second clearing in place.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The code in acpi_i2c_register_devices() assumes that all i2c adapters
have a parent. This is not necessarily the case, for example the
i2c-stub driver instantiate a virtual i2c adapter without a parent.
Check for this to avoid a NULL pointer deference.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Reported-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These checks should be ">=" instead of ">". j is used as an offset into
the table->mc_reg_address[] array and that has
SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE (16) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Always use the regular UVD state for now. This fixes
a performance regression with UVD playback on certain APUs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The crash reported and investigated in commit 5f4513 turned out to be
caused by a change to the read interface on newer (2012) SMCs.
Tests by Chris show that simply reading the data valid line is enough
for the problem to go away. Additional tests show that the newer SMCs
no longer wait for the number of requested bytes, but start sending
data right away. Apparently the number of bytes to read is no longer
specified as before, but instead found out by reading until end of
data. Failure to read until end of data confuses the state machine,
which eventually causes the crash.
As a remedy, assuming bit0 is the read valid line, make sure there is
nothing more to read before leaving the read function.
Tested to resolve the original problem, and runtested on MBA3,1,
MBP4,1, MBP8,2, MBP10,1, MBP10,2. The patch seems to have no effect on
machines before 2012.
Tested-by: Chris Murphy <chris@cmurf.com>
Cc: stable@vger.kernel.org
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Disable MSIs for now until we can fix them up
* nouveau/drm-nouveau-next:
drm/nouveau/mc: disable msi support by default, it's busted in tons of places
Commit 8b9ba7a3 'drm/gma500: use gem get/put page helpers' was missing a
line, which resulted in garbled screen.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Guillaume CLÉMENT <gclement@baobob.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
File drivers/leds/leds-lp55xx-common.c refuse to change led_current sysfs
attribute if value is higher than max_current specified in board file. By default
global C variables are zero, so changing always failed. This patch adding missing
max_current and setting it to max safe value 100 (10 mA).
It is unclear which commit exactly caused this regression as the lp5523
driver was broken and was hiding the platform data breakage. Now
the driver is fixed so this should be fixed as well.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Joerg Reisenweber <joerg@openmoko.org>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since dra7 reuses the function 'omap5_realtime_timer_init' in
arch/arm/mach-omap2/board-generic.c as timer init function, it has to be
built for this SoC as well.
Signed-off-by: Simon Barth <Simon.Pe.Barth@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.
With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):
...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...
WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state
So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull perf fixes from Ingo Molnar:
"Various fixlets:
On the kernel side:
- fix a race
- fix a bug in the handling of the perf ring-buffer data page
On the tooling side:
- fix the handling of certain corrupted perf.data files
- fix a bug in 'perf probe'
- fix a bug in 'perf record + perf sched'
- fix a bug in 'make install'
- fix a bug in libaudit feature-detection on certain distros"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf session: Fix infinite loop on invalid perf.data file
perf tools: Fix installation of libexec components
perf probe: Fix to find line information for probe list
perf tools: Fix libaudit test
perf stat: Set child_pid after perf_evlist__prepare_workload()
perf tools: Add default handler for mmap2 events
perf/x86: Clean up cap_user_time* setting
perf: Fix perf_pmu_migrate_context
Currently hdmi_setup_audio_infoframe() reprograms the HDA channel
mapping only when the infoframe is not up-to-date or the non-PCM flag
has changed.
However, when just the channel map has been changed, the infoframe may
still be up-to-date and non-PCM flag may not have changed, so the new
channel map is not actually programmed into the HDA codec.
Notably, this failing case is also always triggered when the device is
already in a prepared state and a new channel map is configured while
changing only the channel positions (for example, plain
"speaker-test -c2 -m FR,FL").
Fix that by always programming the channel map in
hdmi_setup_audio_infoframe(). Tested on Intel HDMI.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* The libaudit test was failing in some systems due to a unescaped newline, fix
it so that the 'trace' tool can be built in such systems.
* Fix installation of libexec components.
* Add default handler for mmap2 events so that tools that don't explicitely
define an MMAP2 handler don't crash, fix from David Ahern.
* Fix to find line information for probe list, from Masami Hiramatsu.
* Set child_pid after perf_evlist__prepare_workload(), fix from Namhyung Kim.
* Fix infinite loop on invalid perf.data file, from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
irq_exit() is now called on the irq stack, which can trigger a switch to
the softirq stack from the irq stack. If an interrupt happens at that
point, we will not properly detect the re-entrancy and clobber the
original return context on the irq stack.
This fixes it. The side effect is to prevent all nesting from softirq
stack to irq stack even in the "safe" case but it's simpler that way and
matches what x86_64 does.
Reported-by: Cédric Le Goater <clg@fr.ibm.com>
Tested-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull HID fixes from Jiri Kosina:
- fix for hidraw reference counting regression, by Manoj Chourasia
- fix for minor number allocation for uhid, by David Herrmann
- other small unsorted fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: fix FF deadlock
HID: add Holtek USB ID 04d9:a081 SHARKOON DarkGlider
HID: hidraw: close underlying device at removal of last reader
HID: roccat: Fix "cannot create duplicate filename" problems
HID: uhid: allocate static minor
Pull Tile bugfixes from Chris Metcalf:
"This fixes some serious issues with PREEMPT support, and a couple of
smaller corner-case issues fixed in the last couple of weeks"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch: tile: re-use kbasename() helper
tile: use a more conservative __my_cpu_offset in CONFIG_PREEMPT
tile: ensure interrupts disabled for preempt_schedule_irq()
tile: change lock initalization in hardwall
tile: include: asm: use 'long long' instead of 'u64' for atomic64_t and its related functions
The input core has an internal spinlock that is acquired during event
injection via input_event() and friends but also held during FF callbacks.
That means, there is no way to share a lock between event-injection and FF
handling. Unfortunately, this is what is required for wiimote state
tracking and what we do with state.lock and input->lock.
This deadlock can be triggered when using continuous data reporting and FF
on a wiimote device at the same time. I takes me at least 30m of
stress-testing to trigger it but users reported considerably shorter
times (http://bpaste.net/show/132504/) when using some gaming-console
emulators.
The real problem is that we have two copies of internal state, one in the
wiimote objects and the other in the input device. As the input-lock is
not supposed to be accessed from outside of input-core, we have no other
chance than offloading FF handling into a worker. This actually works
pretty nice and also allows to implictly merge fast rumble changes into a
single request.
Due to the 3-layered workers (rumble+queue+l2cap) this might reduce FF
responsiveness. Initial tests were fine so lets fix the race first and if
it turns out to be too slow we can always handle FF out-of-band and skip
the queue-worker.
Cc: <stable@vger.kernel.org> # 3.11+
Reported-by: Thomas Schneider
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 1400eb6 (MIPS: r4k,octeon,r2300: stack protector: change canary
per task) was merged in v3.11 and introduced assembly in the MIPS resume
functions to update the value of the current canary in
__stack_chk_guard. However it used PTR_L resulting in a load of the
canary value, instead of PTR_LA to construct its address. The value is
intended to be random but is then treated as an address in the
subsequent LONG_S (store).
This was observed to cause a fault and panic:
CPU 0 Unable to handle kernel paging request at virtual address 139fea20, epc == 8000cc0c, ra == 8034f2a4
Oops[#1]:
...
$24 : 139fea20 1e1f7cb6
...
Call Trace:
[<8000cc0c>] resume+0xac/0x118
[<8034f2a4>] __schedule+0x5f8/0x78c
[<8034f4e0>] schedule_preempt_disabled+0x20/0x2c
[<80348eec>] rest_init+0x74/0x84
[<804dc990>] start_kernel+0x43c/0x454
Code: 3c18804b 8f184030 8cb901f8 <af190000> 00c0e021 8cb002f0 8cb102f4 8cb202f8 8cb302fc
This can also be forced by modifying
arch/mips/include/asm/stackprotector.h so that the default
__stack_chk_guard value is more likely to be a bad (or unaligned)
pointer.
Fix it to use PTR_LA instead, to load the address of the canary value,
which the LONG_S can then use to write into it.
Reported-by: bobjones (via #mipslinux on IRC)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull s390 fixes from Martin Schwidefsky:
"A couple of bux fixes, notable are the regression with ptrace vs
restarting system calls and the patch for kdump to be able to copy
from virtual memory"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix system call restart after inferior call
s390: Allow vmalloc target buffers for copy_from_oldmem()
s390/sclp: properly detect line mode console
s390/kprobes: add exrl to list of prohibited opcodes
s390/3270: fix return value check in tty3270_resize_work()
Daniel writes:
Just a few important fixes, all cc: stable (I've checked this time around
and made sure they're really there ...). The dpms one is a regression from
the modeset rework and has a good chance to rectify Linus' hdmi issues.
* tag 'drm-intel-fixes-2013-10-07' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only apply DPMS to the encoder if enabled
drm/i915: Mask LPSP to get PSR working even with Power Well in use by audio.
drm/i915/hsw: Disable L3 caching of atomic memory operations.
drm/i915: fix rps.vlv_work initialization
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target fixes queued up for v3.12-rc4 code.
The highlights include:
- Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
- Allow sess_cmd_map allocation failure fallback to use vzalloc
- Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
- Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
zero scsi_status bug
- Make iscsi-target do acknowledgement tag release from RX context
- Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags
Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
legacy wait_for_task=true release during fast-past StatSN
acknowledgement, and two other SRP target related patches that address
long-standing issues that are CC'ed for v3.3+.
Extra thanks to Thomas Glanzmann for his testing feedback with
COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
iscsi-target: Perform release of acknowledged tags from RX context
iscsi-target: Only perform wait_for_tasks when performing shutdown
target: Fail on non zero scsi_status in compare_and_write_callback
target: Fix recursive COMPARE_AND_WRITE callback failure
target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
ib_srpt: always set response for task management
target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
ib_srpt: Destroy cm_id before destroying QP.
target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the slave dmanegine fixes. We have the fix for deadlock issue
on imx-dma by Michael and Josh's edma config fix along with author
change"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: imx-dma: fix callback path in tasklet
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
edma: Update author email address
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes, including a regression fix from
Liu Bo that solves rare crashes with compression on.
I've merged my for-linus up to 3.12-rc3 because the top commit is only
meant for 3.12. The rest of the fixes are also available in my master
branch on top of my last 3.11 based pull"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Fix crash due to not allocating integrity data for a bioset
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
Btrfs: eliminate races in worker stopping code
Btrfs: fix crash of compressed writes
Btrfs: fix transid verify errors when recovering log tree
Pull GPIO fixes from Linus Walleij:
"Two patches for the OMAP driver, dealing with setting up IRQs properly
on the device tree boot path"
* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/omap: auto-setup a GPIO when used as an IRQ
gpio/omap: maintain GPIO and IRQ usage separately
Pull USB fixes from Greg KH:
"Here are none fixes for various USB driver problems. The majority are
gadget/musb fixes, but there are some new device ids in here as well"
* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: add Intel Clovertrail pci id
usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
usb: gadget: f_fs: fix error handling
usb: musb: dsps: do not bind to "musb-hdrc"
USB: serial: option: Ignore card reader interface on Huawei E1750
usb: musb: gadget: fix otg active status flag
usb: phy: gpio-vbus: fix deferred probe from __init
usb: gadget: pxa25x_udc: fix deferred probe from __init
usb: musb: fix otg default state
Pull tty fixes from Greg KH:
"Here are two tty driver fixes for 3.12-rc4.
One fixes the reported regression in the n_tty code that a number of
people found recently, and the other one fixes an issue with xen
consoles that broke in 3.10"
* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
xen/hvc: allow xenboot console to be used again
tty: Fix pty master read() after slave closes
Pull staging fixes from Greg KH:
"Here are 4 tiny staging and iio driver fixes for 3.12-rc4. Nothing
major, just some small fixes for reported issues"
* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
iio:magnetometer: Bugfix magnetometer default output registers
iio: Remove debugfs entries in iio_device_unregister()
iio: amplifiers: ad8366: Remove regulator_put
Pull CIFS fixes from Steve French:
"Small set of cifs fixes. Most important is Jeff's fix that works
around disconnection problems which can be caused by simultaneous use
of user space tools (starting a long running smbclient backup then
doing a cifs kernel mount) or multiple cifs mounts through a NAT, and
Jim's fix to deal with reexport of cifs share.
I expect to send two more cifs fixes next week (being tested now) -
fixes to address an SMB2 unmount hang when server dies and a fix for
cifs symlink handling of Windows "NFS" symlinks"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] update cifs.ko version
[CIFS] Remove ext2 flags that have been moved to fs.h
[CIFS] Provide sane values for nlink
cifs: stop trying to use virtual circuits
CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them
Pull PCI fix from Bjorn Helgaas:
"We merged what was intended to be an MMCONFIG cleanup, but in fact,
for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and it broke all config space for
other domains.
This reverts the change"
* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
Pull ACPI and power management fixes from Rafael Wysocki:
- The resume part of user space driven hibernation (s2disk) is now
broken after the change that moved the creation of memory bitmaps to
after the freezing of tasks, because I forgot that the resume utility
loaded the image before freezing tasks and needed the bitmaps for
that. The fix adds special handling for that case.
- One of recent commits changed the export of acpi_bus_get_device() to
EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
binary modules using that function including one in particularly
widespread use. Change it back to EXPORT_SYMBOL().
- The intel_pstate driver sometimes fails to disable turbo if its
no_turbo sysfs attribute is set. Fix from Srinivas Pandruvada.
- One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
which still (incorrectly) treats non-NULL as non-error. Fix from
Philipp Zabel.
- The SPEAr cpufreq driver uses a wrong variable type in one place
preventing it from catching errors returned by one of the functions
called by it. Fix from Sachin Kamat.
* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
Pull xfs bugfixes from Ben Myers:
"There are lockdep annotations for project quotas, a fix for dirent
dtype support on v4 filesystems, a fix for a memory leak in recovery,
and a fix for the build error that resulted from it. D'oh"
* tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: Use kmem_free() instead of free()
xfs: fix memory leak in xlog_recover_add_to_trans
xfs: dirent dtype presence is dependent on directory magic numbers
xfs: lockdep needs to know about 3 dquot-deep nesting
.. so get rid of it. The only indirect users were all the
avc_has_perm() callers which just expanded to have a zero flags
argument.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
free_device rcu callback, scheduled from btrfs_rm_dev_replace_srcdev,
can be processed before btrfs_scratch_superblock is called, which would
result in a use-after-free on btrfs_device contents. Fix this by
zeroing the superblock before the rcu callback is registered.
Cc: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
The current implementation of worker threads in Btrfs has races in
worker stopping code, which cause all kinds of panics and lockups when
running btrfs/011 xfstest in a loop. The problem is that
btrfs_stop_workers is unsynchronized with respect to check_idle_worker,
check_busy_worker and __btrfs_start_workers.
E.g., check_idle_worker race flow:
btrfs_stop_workers(): check_idle_worker(aworker):
- grabs the lock
- splices the idle list into the
working list
- removes the first worker from the
working list
- releases the lock to wait for
its kthread's completion
- grabs the lock
- if aworker is on the working list,
moves aworker from the working list
to the idle list
- releases the lock
- grabs the lock
- puts the worker
- removes the second worker from the
working list
......
btrfs_stop_workers returns, aworker is on the idle list
FS is umounted, memory is freed
......
aworker is waken up, fireworks ensue
With this applied, I wasn't able to trigger the problem in 48 hours,
whereas previously I could reliably reproduce at least one of these
races within an hour.
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
The crash[1] is found by xfstests/generic/208 with "-o compress",
it's not reproduced everytime, but it does panic.
The bug is quite interesting, it's actually introduced by a recent commit
(573aecafca,
Btrfs: actually limit the size of delalloc range).
Btrfs implements delay allocation, so during writeback, we
(1) get a page A and lock it
(2) search the state tree for delalloc bytes and lock all pages within the range
(3) process the delalloc range, including find disk space and create
ordered extent and so on.
(4) submit the page A.
It runs well in normal cases, but if we're in a racy case, eg.
buffered compressed writes and aio-dio writes,
sometimes we may fail to lock all pages in the 'delalloc' range,
in which case, we need to fall back to search the state tree again with
a smaller range limit(max_bytes = PAGE_CACHE_SIZE - offset).
The mentioned commit has a side effect, that is, in the fallback case,
we can find delalloc bytes before the index of the page we already have locked,
so we're in the case of (delalloc_end <= *start) and return with (found > 0).
This ends with not locking delalloc pages but making ->writepage still
process them, and the crash happens.
This fixes it by just thinking that we find nothing and returning to caller
as the caller knows how to deal with it properly.
[1]:
------------[ cut here ]------------
kernel BUG at mm/page-writeback.c:2170!
[...]
CPU: 2 PID: 11755 Comm: btrfs-delalloc- Tainted: G O 3.11.0+ #8
[...]
RIP: 0010:[<ffffffff810f5093>] [<ffffffff810f5093>] clear_page_dirty_for_io+0x1e/0x83
[...]
[ 4934.248731] Stack:
[ 4934.248731] ffff8801477e5dc8 ffffea00049b9f00 ffff8801869f9ce8 ffffffffa02b841a
[ 4934.248731] 0000000000000000 0000000000000000 0000000000000fff 0000000000000620
[ 4934.248731] ffff88018db59c78 ffffea0005da8d40 ffffffffa02ff860 00000001810016c0
[ 4934.248731] Call Trace:
[ 4934.248731] [<ffffffffa02b841a>] extent_range_clear_dirty_for_io+0xcf/0xf5 [btrfs]
[ 4934.248731] [<ffffffffa02a8889>] compress_file_range+0x1dc/0x4cb [btrfs]
[ 4934.248731] [<ffffffff8104f7af>] ? detach_if_pending+0x22/0x4b
[ 4934.248731] [<ffffffffa02a8bad>] async_cow_start+0x35/0x53 [btrfs]
[ 4934.248731] [<ffffffffa02c694b>] worker_loop+0x14b/0x48c [btrfs]
[ 4934.248731] [<ffffffffa02c6800>] ? btrfs_queue_worker+0x25c/0x25c [btrfs]
[ 4934.248731] [<ffffffff810608f5>] kthread+0x8d/0x95
[ 4934.248731] [<ffffffff81060868>] ? kthread_freezable_should_stop+0x43/0x43
[ 4934.248731] [<ffffffff814fe09c>] ret_from_fork+0x7c/0xb0
[ 4934.248731] [<ffffffff81060868>] ? kthread_freezable_should_stop+0x43/0x43
[ 4934.248731] Code: ff 85 c0 0f 94 c0 0f b6 c0 59 5b 5d c3 0f 1f 44 00 00 55 48 89 e5 41 54 53 48 89 fb e8 2c de 00 00 49 89 c4 48 8b 03 a8 01 75 02 <0f> 0b 4d 85 e4 74 52 49 8b 84 24 80 00 00 00 f6 40 20 01 75 44
[ 4934.248731] RIP [<ffffffff810f5093>] clear_page_dirty_for_io+0x1e/0x83
[ 4934.248731] RSP <ffff8801869f9c48>
[ 4934.280307] ---[ end trace 36f06d3f8750236a ]---
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
If we crash with a log, remount and recover that log, and then crash before we
can commit another transaction we will get transid verify errors on the next
mount. This is because we were not zero'ing out the log when we committed the
transaction after recovery. This is ok as long as we commit another transaction
at some point in the future, but if you abort or something else goes wrong you
can end up in this weird state because the recovery stuff says that the tree log
should have a generation+1 of the super generation, which won't be the case of
the transaction that was started for recovery. Fix this by removing the check
and _always_ zero out the log portion of the super when we commit a transaction.
This fixes the transid verify issues I was seeing with my force errors tests.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Every single user passes in '0'. I think we had non-zero users back in
some stone age when selinux_inode_permission() was implemented in terms
of inode_has_perm(), but that complicated case got split up into a
totally separate code-path so that we could optimize the much simpler
special cases.
See commit 2e33405785 ("SELinux: delay initialization of audit data in
selinux_inode_permission") for example.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a build failure caused by calling the free() function which
does not exist in the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit aaaae98022)
Free the memory in error path of xlog_recover_add_to_trans().
Normally this memory is freed in recovery pass2, but is leaked
in the error path.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 519ccb81ac)
The determination of whether a directory entry contains a dtype
field originally was dependent on the filesystem having CRCs
enabled. This meant that the format for dtype beign enabled could be
determined by checking the directory block magic number rather than
doing a feature bit check. This was useful in that it meant that we
didn't need to pass a struct xfs_mount around to functions that
were already supplied with a directory block header.
Unfortunately, the introduction of dtype fields into the v4
structure via a feature bit meant this "use the directory block
magic number" method of discriminating the dirent entry sizes is
broken. Hence we need to convert the places that use magic number
checks to use feature bit checks so that they work correctly and not
by chance.
The current code works on v4 filesystems only because the dirent
size roundup covers the extra byte needed by the dtype field in the
places where this problem occurs.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 367993e7c6)
Michael Semon reported that xfs/299 generated this lockdep warning:
=============================================
[ INFO: possible recursive locking detected ]
3.12.0-rc2+ #2 Not tainted
---------------------------------------------
touch/21072 is trying to acquire lock:
(&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
but task is already holding lock:
(&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&xfs_dquot_other_class);
lock(&xfs_dquot_other_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by touch/21072:
#0: (sb_writers#10){++++.+}, at: [<c11185b6>] mnt_want_write+0x1e/0x3e
#1: (&type->i_mutex_dir_key#4){+.+.+.}, at: [<c11078ee>] do_last+0x245/0xe40
#2: (sb_internal#2){++++.+}, at: [<c122c9e0>] xfs_trans_alloc+0x1f/0x35
#3: (&(&ip->i_lock)->mr_lock/1){+.+...}, at: [<c126cd1b>] xfs_ilock+0x100/0x1f1
#4: (&(&ip->i_lock)->mr_lock){++++-.}, at: [<c126cf52>] xfs_ilock_nowait+0x105/0x22f
#5: (&dqp->q_qlock){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
#6: (&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
The lockdep annotation for dquot lock nesting only understands
locking for user and "other" dquots, not user, group and quota
dquots. Fix the annotations to match the locking heirarchy we now
have.
Reported-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit f112a04971)
Fix to find the correct (as much as possible) line information for
listing probes. Without this fix, perf probe --list action will show
incorrect line information as below;
probe:getname_flags (on getname_flags@ksrc/linux-3/fs/namei.c)
probe:getname_flags_1 (on getname:-89@x86/include/asm/current.h)
probe:getname_flags_2 (on user_path_at_empty:-2054@x86/include/asm/current.h)
The minus line number is obviously wrong, and current.h is not related
to the probe point. Deeper investigation discovered that there were 2
issues related to this bug, and minor typos too.
The 1st issue is the rack of considering about nested inlined functions,
which causes the wrong (relative) line number.
The 2nd issue is that the dwarf line info is not correct at those
points. It points 14th line of current.h.
Since it seems that the line info includes somewhat unreliable
information, this fixes perf to try to find correct line information
from both of debuginfo and line info as below.
1) Probe address is the entry of a function instance
In this case, the line is set as the function declared line.
2) Probe address is the entry of an expanded inline function block
In this case, the line is set as the function call-site line.
This means that the line number is relative from the entry line
of caller function (which can be an inlined function if nested)
3) Probe address is inside a function instance or an expanded
inline function block
In this case, perf probe queries the line number from lineinfo
and verify the function declared file is same as the file name
queried from lineinfo.
If the file name is different, it is a failure case. The probe
address is shown as symbol+offset.
4) Probe address is not in the any function instance
This is a failure case, the probe address is shown as
symbol+offset.
With this fix, perf probe -l shows correct probe lines as below;
probe:getname_flags (on getname_flags@ksrc/linux-3/fs/namei.c)
probe:getname_flags_1 (on getname:2@ksrc/linux-3/fs/namei.c)
probe:getname_flags_2 (on user_path_at_empty:4@ksrc/linux-3/fs/namei.c)
Changes at v2:
- Fix typos in the function comments. (Thanks to Namhyung Kim)
- Use die_find_top_inlinefunc instead of die_find_inlinefunc_next.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130930092144.1693.11058.stgit@udc4-manage.rcp.hitachi.co.jp
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In ubuntu systems the libaudit test was always failing due to the
newline in the printf call not being escaped, which somehow didn't
prevented the test from working as expected on other systems, such
as fedora18.
Fix it by removing the newline, as this is just a test, that program is
just a compile test.
The error messages, obtained using 'make V=1':
CHK libaudit
<stdin>: In function ‘main’:
<stdin>:5:9: error: missing terminating " character [-Werror]
<stdin>:5:2: error: missing terminating " character
<stdin>:6:1: error: missing terminating " character [-Werror]
<stdin>:6:1: error: missing terminating " character
<stdin>:7:2: error: expected expression before ‘return’
<stdin>:8:1: error: expected ‘;’ before ‘}’ token
cc1: all warnings being treated as errors
config/Makefile:241: No libaudit.h found, disables 'trace' tool, please install audit-libs-devel or libaudit-dev
After this change the test works as expected in all systems tested and the
'trace' tool is built when the needed devel packages are installed.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-0trw8qs9hafeopc0vj1sicay@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit ebd97be635 ('PCI: remove ARCH_SUPPORTS_MSI kconfig option')
removed the ARCH_SUPPORTS_MSI option which architectures could select
to indicate that they support MSI. Now, all architectures are supposed
to build fine when MSI support is enabled: instead of having the
architecture tell *when* MSI support can be used, it's up to the
architecture code to ensure that MSI support can be enabled.
On x86, commit ebd97be635 removed the following line:
select ARCH_SUPPORTS_MSI if (X86_LOCAL_APIC && X86_IO_APIC)
Which meant that MSI support was only available when the local APIC
and I/O APIC were enabled. While this is always true on SMP or x86-64,
it is not necessarily the case on i386 !SMP.
The below patch makes sure that the local APIC and I/O APIC support is
always enabled when MSI support is enabled. To do so, it:
* Ensures the X86_UP_APIC option is not visible when PCI_MSI is
enabled. This is the option that allows, on UP machines, to enable
or not the APIC support. It is already not visible on SMP systems,
or x86-64 systems, for example. We're simply also making it
invisible on i386 MSI systems.
* Ensures that the X86_LOCAL_APIC and X86_IO_APIC options are 'y'
when PCI_MSI is enabled.
Notice that this change requires a change in drivers/iommu/Kconfig to
avoid a recursive Kconfig dependencey. The AMD_IOMMU option selects
PCI_MSI, but was depending on X86_IO_APIC. This dependency is no
longer needed: as soon as PCI_MSI is selected, the presence of
X86_IO_APIC is guaranteed. Moreover, the AMD_IOMMU already depended on
X86_64, which already guaranteed that X86_IO_APIC was enabled, so this
dependency was anyway redundant.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: http://lkml.kernel.org/r/1380794354-9079-1-git-send-email-thomas.petazzoni@free-electrons.com
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull fuse bugfixes from Miklos Szeredi:
"This contains two more fixes by Maxim for writeback/truncate races and
fixes for RCU walk in fuse_dentry_revalidate()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: no RCU mode in fuse_access()
fuse: readdirplus: fix RCU walk
fuse: don't check_submounts_and_drop() in RCU walk
fuse: fix fallocate vs. ftruncate race
fuse: wait for writeback in fuse_file_fallocate()
Pull iommu fixes from Joerg Roedel:
"A couple of fixes from the IOMMU side:
- some small fixes for the new ARM-SMMU driver
- a register offset correction for VT-d
- add MAINTAINERS entry for drivers/iommu
Overall no really big or intrusive changes"
* tag 'iommu-fixes-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
x86/iommu: correct ICS register offset
MAINTAINERS: add overall IOMMU section
iommu/arm-smmu: don't enable SMMU device until probing has completed
iommu/arm-smmu: fix iommu_present() test in init
iommu/arm-smmu: fix a signedness bug
Pull ARM64 fixes/updates from Catalin Marinas:
- Bug-fixes (get_user/put_user, incorrect register width for ASID,
FPSIMD initialisation)
- Kconfig clean-up
- defconfig update
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Remove duplicate DEBUG_STACK_USAGE config
arm64: include VIRTIO_{MMIO,BLK} in defconfig
arm64: include EXT4 in defconfig
arm64: fix possible invalid FPSIMD initialization state
arm64: use correct register width when retrieving ASID
arm64: avoid multiple evaluation of ptr in get_user/put_user()
Pull MIPS fixes from Ralf Baechle:
"Two small fixes for 3.12 only this week. I have a few more fixes
pending but those are conceptually more complex so will have to wait
for a bit longer"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix forgotten preempt_enable() when CPU has inclusive pcaches
MIPS: Alchemy: MTX-1: fix incorrect placement of __initdata tag
Pull x86 fixes from Ingo Molnar:
"Two simplefb fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/simplefb: Mark framebuffer mem-resources as IORESOURCE_BUSY to avoid bootup warning
x86/simplefb: Fix overflow causing bogus fall-back
Pull irq fix from Ingo Molnar:
"Frederic's minimal fix for hardirq/softirq nesting crashes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq: Force hardirq exit's softirq processing on its own stack
We need to free the ld_active list head before jumping into the callback
routine. Otherwise the callback could run into issue_pending and change
our ld_active list head we just going to free. This will run the channel
list into an currupted and undefined state.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the cap_user_time_zero capability has different tests than
cap_user_time; even though they expose the exact same data.
Switch from CONSTANT && NONSTOP to sched_clock_stable to also deal
with multi cabinet machines and drop the tsc_disabled() check.. non of
this will work sanely without tsc anyway.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-nmgn0j0muo1r4c94vlfh23xy@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While auditing the list_entry usage due to a trinity bug I found that
perf_pmu_migrate_context violates the rules for
perf_event::event_entry.
The problem is that perf_event::event_entry is a RCU list element, and
hence we must wait for a full RCU grace period before re-using the
element after deletion.
Therefore the usage in perf_pmu_migrate_context() which re-uses the
entry immediately is broken. For now introduce another list_head into
perf_event for this specific usage.
This doesn't actually fix the trinity report because that never goes
through this code.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-mkj72lxagw1z8fvjm648iznw@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The `insn_bits` handler `ni_65xx_dio_insn_bits()` has a `for` loop that
currently writes (optionally) and reads back up to 5 "ports" consisting
of 8 channels each. It reads up to 32 1-bit channels but can only read
and write a whole port at once - it needs to handle up to 5 ports as the
first channel it reads might not be aligned on a port boundary. It
breaks out of the loop early if the next port it handles is beyond the
final port on the card. It also breaks out early on the 5th port in the
loop if the first channel was aligned. Unfortunately, it doesn't check
that the current port it is dealing with belongs to the comedi subdevice
the `insn_bits` handler is acting on. That's a bug.
Redo the `for` loop to terminate after the final port belonging to the
subdevice, changing the loop variable in the process to simplify things
a bit. The `for` loop could now try and handle more than 5 ports if the
subdevice has more than 40 channels, but the test `if (bitshift >= 32)`
ensures it will break out early after 4 or 5 ports (depending on whether
the first channel is aligned on a port boundary). (`bitshift` will be
between -7 and 7 inclusive on the first iteration, increasing by 8 for
each subsequent operation.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org> # 3.10.y 3.11.y 3.12.y
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch bumps the default number of tags allocated per session by
iscsi-target via transport_alloc_session_tags() -> percpu_ida_init()
by another (tag_num / 2).
This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.
Using a larger value here is also useful to prevent percpu_ida_alloc()
from having to steal tags from other CPUs when no tags are available
on the local CPU, while waiting for unacknowledged tags to be released.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts iscsit_ack_from_expstatsn() to populate a local
ack_list of commands, and call iscsit_free_cmd() directly from RX
thread context, instead of using iscsit_add_cmd_to_immediate_queue()
to queue the acknowledged commands to be released from TX thread
context.
It is helpful to release the acknowledge commands as quickly as
possible, along with the associated percpu_ida tags, in order to
prevent percpu_ida_alloc() from having to steal tags from other
CPUs while waiting for iscsit_free_cmd() to happen from TX thread
context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes transport_generic_free_cmd() to only wait_for_tasks
when shutdown=true is passed to iscsit_free_cmd().
With the advent of >= v3.10 iscsi-target code using se_cmd->cmd_kref,
the extra wait_for_tasks with shutdown=false is unnecessary, and may
end up causing an extra context switch when releasing WRITEs.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Power Well in use forces constantly PSR to exit.
On recent Kernel I noticed that PSR Performance Counter was always 0
indicating that PSR was never really achieved.
By masking LPSP, PSR can work normally and save power on Haswell.
Two bugs had been raised with PSR flag enabled:
- "Screen flickers when booted by enabling PSR in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
- "When booting the DUT with PSR feature enabled in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
Both bugs has been fixed by this patch.
v2: proper comment for -fixes
Tested-by: Selvaraj, Elavarasan <elavarasanx.selvaraj@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull ARC fix from Vineet Gupta:
"Chrisitian found/fixed issue with SA_SIGINFO based signal handler
corrupting the user space registers post after signal handling"
* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix signal frame management for SA_SIGINFO
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few powerpc fixes, all aimed at -stable, found in part
thanks to the ramping up of a major distro testing and in part thanks
to the LE guys hitting all sort interesting corner cases.
The most scary are probably the register clobber issues in
csum_partial_copy_generic(), especially since Anton even had a test
case for that thing, which didn't manage to hit the bugs :-)
Another highlight is that memory hotplug should work again with these
fixes.
Oh and the vio modalias one is worse than the cset implies as it
upsets distro installers, so I've been told at least, which is why I'm
shooting it to stable"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/tm: Switch out userspace PPR and DSCR sooner
powerpc/tm: Turn interrupts hard off in tm_reclaim()
powerpc/perf: Fix handling of FAB events
powerpc/vio: Fix modalias_show return values
powerpc/iommu: Use GFP_KERNEL instead of GFP_ATOMIC in iommu_init_table()
powerpc/sysfs: Disable writing to PURR in guest mode
powerpc: Restore registers on error exit from csum_partial_copy_generic()
powerpc: Fix parameter clobber in csum_partial_copy_generic()
powerpc: Fix memory hotplug with sparse vmemmap
3e00a09d2f
(spi/hspi: Convert to core runtime PM)
enabled master->auto_runtime_pm.
Then, pm_runtime_enable() is required *before*
spi_register_master() calling.
This patch fixed it up.
Kernel will hang up with "spi_master spi0: Failed to power device: -13"
message without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch addresses a bug for backends such as IBLOCK that perform
asynchronous completion via transport_complete_cmd(), that will call
target_complete_failure_work() -> transport_generic_request_failure(),
upon exception status and invoke cmd->transport_complete_callback()
-> compare_and_write_callback() incorrectly during the failure case.
It adds a check for a non zero se_cmd->scsi_status within the first
invocation of compare_and_write_callback(), and will jump to out plus
up se_device->caw_sem before exiting the callback.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug when compare_and_write_callback() invoked from
target_complete_ok_work() hits an failure from __target_execute_cmd() ->
cmd->execute_cmd(), that ends up calling transport_generic_request_failure()
-> compare_and_write_post(), thus causing SCF_COMPARE_AND_WRITE_POST to
incorrectly be set.
The result of this bug is that target_complete_ok_work() no longer hits
the if (!rc && !(cmd->se_cmd_flags & SCF_COMPARE_AND_WRITE_POST) check
that forces an immediate return, and instead double completes the se_cmd
in question, triggering an OOPs in the process.
This patch changes compare_and_write_post() to only set this bit when a
failure has not already occured to ensure the immediate return from within
target_complete_ok_work(), and thus allow transport_generic_request_failure()
to handle the sending of the CHECK_CONDITION exception status.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch resets se_cmd->data_length for COMPARE_AND_WRITE emulation
within sbc_compare_and_write() to NoLB * block_size in order to address
a bug with FILEIO backends where a I/O failure will occur when data_length
does not match the I/O size being actually dispatched for the individual
per block READs + WRITEs.
This is done late enough in sbc_compare_and_write() after the memory
allocations have occured in transport_generic_new_cmd() to not cause
any unwanted side-effects.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The SRP specification requires:
"Response data shall be provided in any SRP_RSP response that is sent in
response to an SRP_TSK_MGMT request (see 6.7). The information in the
RSP_CODE field (see table 24) shall indicate the completion status of
the task management function."
So fix this to avoid the SRP initiator interprets task management functions
that succeeded as failed.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Otherwise using any atomic memory operation will lock up the GPU due
to a Haswell hardware bug.
v2: Use the _MASKED_BIT_ENABLE macro. Drop drm parameter definition.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: <stable@vger.kernel.org>
[danvet: Fix checkpatch fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we do a treclaim or trecheckpoint we end up running with userspace
PPR and DSCR values. Currently we don't do anything special to avoid
running with user values which could cause a severe performance
degradation.
This patch moves the PPR and DSCR save and restore around treclaim and
trecheckpoint so that we run with user values for a much shorter period.
More care is taken with the PPR as it's impact is greater than the DSCR.
This is similar to user exceptions, where we run HTM_MEDIUM early to
ensure that we don't run with a userspace PPR values in the kernel.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can't take IRQs in tm_reclaim as we might have a bogus r13 and r1.
This turns IRQs hard off in this function.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4df4899 "Add power8 EBB support" included a bug in the handling
of the FAB_CRESP_MATCH and FAB_TYPE_MATCH fields.
These values are pulled out of the event code using EVENT_THR_CTL_SHIFT,
however we were then or'ing that value directly into MMCR1.
This meant we were failing to set the FAB fields correctly, and also
potentially corrupting the value for PMC4SEL. Leading to no counts for
the FAB events and incorrect counts for PMC4.
The fix is simply to shift left the FAB value correctly before or'ing it
with MMCR1.
Reported-by: Sooraj Ravindran Nair <soonair3@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
modalias_show() should return an empty string on error, not -ENODEV.
This causes the following false and annoying error:
> find /sys/devices -name modalias -print0 | xargs -0 cat >/dev/null
cat: /sys/devices/vio/4000/modalias: No such device
cat: /sys/devices/vio/4001/modalias: No such device
cat: /sys/devices/vio/4002/modalias: No such device
cat: /sys/devices/vio/4004/modalias: No such device
cat: /sys/devices/vio/modalias: No such device
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Under heavy (DLPAR?) stress, we tripped this panic() in
arch/powerpc/kernel/iommu.c::iommu_init_table():
page = alloc_pages_node(nid, GFP_ATOMIC, get_order(sz));
if (!page)
panic("iommu_init_table: Can't allocate %ld bytes\n", sz);
Before the panic() we got a page allocation failure for an order-2
allocation. There appears to be memory free, but perhaps not in the
ATOMIC context. I looked through all the call-sites of
iommu_init_table() and didn't see any obvious reason to need an ATOMIC
allocation. Most call-sites in fact have an explicit GFP_KERNEL
allocation shortly before the call to iommu_init_table(), indicating we
are not in an atomic context. There is some indirection for some paths,
but I didn't see any locks indicating that GFP_KERNEL is inappropriate.
With this change under the same conditions, we have not been able to
reproduce the panic.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
arch/powerpc/kernel/sysfs.c exports PURR with write permission.
This may be valid for kernel in phyp mode. But writing to
the file in guest mode causes crash due to a priviledge violation
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
The csum_partial_copy_generic() function saves the PowerPC non-volatile
r14, r15, and r16 registers for the main checksum-and-copy loop.
Unfortunately, it fails to restore them upon error exit from this loop,
which results in silent corruption of these registers in the presumably
rare event of an access exception within that loop.
This commit therefore restores these register on error exit from the loop.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The csum_partial_copy_generic() uses register r7 to adjust the remaining
bytes to process. Unfortunately, r7 also holds a parameter, namely the
address of the flag to set in case of access exceptions while reading
the source buffer. Lacking a quantum implementation of PowerPC, this
commit instead uses register r9 to do the adjusting, leaving r7's
pointer uncorrupted.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previous commit 46723bfa540... introduced a new config option
HAVE_BOOTMEM_INFO_NODE that ended up breaking memory hot-remove for ppc
when sparse vmemmap is not defined.
This patch defines HAVE_BOOTMEM_INFO_NODE for ppc and adds the call to
register_page_bootmem_info_node. Without this we get a BUG_ON for memory
hot remove in put_page_bootmem().
This also adds a stub for register_page_bootmem_memmap to allow ppc to build
with sparse vmemmap defined. Leaving this as a stub is fine since the same
vmemmap addresses are also handled in vmemmap_populate and as such are
properly mapped.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.9+]
gfn_to_memslot() can return NULL or invalid slot. We need to check slot
validity before accessing it.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
IORESOURCE_BUSY is used to mark temporary driver mem-resources
instead of global regions. This suppresses warnings if regions
overlap with a region marked as BUSY.
This was always the case for VESA/VGA/EFI framebuffer regions so
do the same for simplefb regions. The reason we do this is to
allow device handover to real GPU drivers like
i915/radeon/nouveau which get the same regions via PCI BARs.
Maybe at some point we will be able to unregister platform
devices properly during the handover. In this case the simplefb
region would get removed before the new region is created.
However, this is currently not the case and would require rather
huge changes in remove_conflicting_framebuffers(). Add the BUSY
marker now and try to eventually rewrite the handover for a next release.
Also see kernel/resource.c for more information:
/*
* if a resource is "BUSY", it's not a hardware resource
* but a driver mapping of such a resource; we don't want
* to warn for those; some drivers legitimately map only
* partial hardware resources. (example: vesafb)
*/
This suppresses warnings like:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 199 at arch/x86/mm/ioremap.c:171 __ioremap_caller+0x2e3/0x390()
Info: mapping multiple BARs. Your kernel is fine.
Call Trace:
dump_stack+0x54/0x8d
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
iomem_map_sanity_check+0xac/0xe0
__ioremap_caller+0x2e3/0x390
ioremap_wc+0x32/0x40
i915_driver_load+0x670/0xf50 [i915]
...
Reported-by: Tom Gundersen <teg@jklm.no>
Tested-by: Tom Gundersen <teg@jklm.no>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1380724864-1757-1-git-send-email-dh.herrmann@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull ARM SoC fixes from Olof Johansson:
"We have a fairly large batch of fixes this time around, mostly just
due to various platforms all having a fix or two more than usual.
Worth pointing out are:
- A fix for EDMA on Davinci/OMAP where channel allocation broke with
the DT conversion. Due to some miscommunication we didn't
understand the impact of the breakage, so we were pushing back on
it for 3.12, but it sounds like it's actually breaking quite a few
people out there.
- A bunch of fixes for Marvell platforms, some straggling fixes for
merge window fallout and some fixes for a couple of the platforms
(Netgear RN102 in particular).
- A fix for a race between multi-cluster power management and cpu
hotplug on Versatile Express.
And a bunch of other smaller fixes that all add up.
We'll be switching over into stricter regressions-only mode from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: multi_v7_defconfig: add SDHCI for i.MX
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: at91: sam9g45: shutdown ddr1 too when rebooting
MAINTAINERS: ARM: SIRF: use kernel.org mail box
MAINTAINERS: ARM: SIRF: add missed drivers into maintain list
ARM: edma: Fix clearing of unused list for DT DMA resources
ARM: vexpress: tc2: fix hotplug/idle/kexec race on cluster power down
ARM: dts: sirf: fix interrupt and dma prop of VIP for prima2 and atlas6
ARM: dts: sirf: fix the ranges of peri-iobrg of prima2
ARM: dts: makefile: build atlas6-evb.dtb for ARCH_ATLAS6
ARM: dts: sirf: fix fifosize, clks, dma channels for UART
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
ARM: mach-integrator: Add stub for pci_v3_early_init() for !CONFIG_PCI
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
...
Previously, when a signal was registered with SA_SIGINFO, parameters 2
and 3 of the signal handler were written to registers r1 and r2 before
the register set was saved. This led to corruption of these two
registers after returning from the signal handler (the wrong values were
restored).
With this patch, registers are now saved before any parameters are
passed, thus maintaining the processor state from before signal entry.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull sparc fixes from David Miller:
"Couple of small bug fixes:
1) strlcpy in ldom_reboot() is still not quite right, use sprintf
instead from Kees Cook.
2) Generic hugetlb interface pte checks should use the widest return
type, otherwise high bits can get chopped off.
3) Fix build with PCI MSI enabled on 32-bit sparc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix MSI build failure on Sparc32
sparc: remove deprecated IRQF_DISABLED
mm: Fix generic hugetlb pte check return type.
sparc: fix ldom_reboot buffer overflow harder
From Jason Cooper:
mvebu fixes for v3.12 (round 2)
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
* tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
Signed-off-by: Olof Johansson <olof@lixom.net>
Turn on SDHCI for i.MX support so machines can boot with local rootfs
on SD. Tested on a Wandboard Quad.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Commit ebd97be635 ('PCI: remove ARCH_SUPPORTS_MSI kconfig option')
removes the ARCH_SUPPORTS_MSI Kconfig option that allowed
architectures to indicate whether they support PCI MSI or not. Now,
PCI MSI support can be compiled in on any architecture thanks to the
use of weak functions thanks to 4287d824f2 ('PCI: use weak functions
for MSI arch-specific functions').
So, architecture specific code is now responsible to ensure that its
PCI MSI code builds in all cases, or be appropriately conditionally
compiled.
On Sparc, the MSI support is only provided for Sparc64, so the
ARCH_SUPPORTS_MSI kconfig option was only selected for SPARC64, and
not for the Sparc architecture as a whole. Therefore, removing
ARCH_SUPPORTS_MSI broke Sparc32 configurations with CONFIG_PCI_MSI=y,
because the Sparc-specific MSI code is not designed to be built on
Sparc32.
To solve this, this commit ensures that the Sparc MSI code is only
built on Sparc64. This is done thanks to a new Kconfig Makefile helper
option SPARC64_PCI_MSI, modeled after the existing SPARC64_PCI. The
SPARC64_PCI_MSI option is an hidden option that is true when both
Sparc64 PCI support is enabled and MSI is enabled. The
arch/sparc/kernel/pci_msi.c file is now only built when
SPARC64_PCI_MSI is true.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from sparc architecture
code. It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The include/asm-generic/hugetlb.h stubs that just vector huge_pte_*()
calls to the pte_*() implementations won't work in certain situations.
x86 and sparc, for example, return "unsigned long" from the bit
checks, and just go "return pte_val(pte) & PTE_BIT_FOO;"
But since huge_pte_*() returns 'int', if any high bits on 64-bit are
relevant, they get chopped off.
The net effect is that we can loop forever trying to COW a huge page,
because the huge_pte_write() check signals false all the time.
Reported-by: Gurudas Pai <gurudas.pai@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: David Rientjes <rientjes@google.com>
The length argument to strlcpy was still wrong. It could overflow the end of
full_boot_str by 5 bytes. Instead of strcat and strlcpy, just use snprint.
Reported-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Install targets (install, zinstall, uinstall) on arm have a dependency
to vmlinux. This may cause parts of the kernel to be rebuilt during
installation. We must avoid this since this may run as root. Install
targets "ABSOLUTELY MUST NOT MODIFY THE SOURCE TREE." as Linus
emphasized this in:
http://lkml.org/lkml/2013/7/10/600
So on arm and maybe other archs we need the same as for x86:
1648e4f8 x86, kbuild: make "make install" not depend on vmlinux
This patch fixes this for arm. Dependencies are removed and instead a
check to install.sh is added for the files that are needed.
This issue was uncovered by this build error where the -j option is
used in conjunction with install targets:
$ make <makeflags>
$ make <makeflags> zinstall
...
DEPMOD
Usage: .../scripts/depmod.sh /sbin/depmod <kernelrelease>
(INSTALL_MOD_PATH and INSTALL_PATH variables set, so no root perms
required in this case.)
The problem is that zinstall on arm due to its dependency to vmlinux
does a prepare/prepare3 and finally does a forced rewrite of
kernel.release even if it exists already.
Rebuilding kernel.release removes it first and then recreates it. This
might race with another parallel make job running depmod.
So this patch should fix this one too.
Also quoting $(KERNELRELEASE) arg for install.sh as this messes
argument order in case it is empty (which is the case if the kernel
was not built yet).
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Signed-off-by: Robert Richter <rric@kernel.org>
Acked-by: Michal Marek <mmarek@suse.cz>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This config item already exists generically in lib/Kconfig.debug.
Remove the duplicate config in arm64.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull sound fixes from Takashi Iwai:
"All small, mostly driver-specific fixes: a few ASoC driver fixes
(trivial stable fixes, sgtl5000 fixes), one DPCM fix, an old AC97 ID,
and a fix for HD-audio Conexant GPIO"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix GPIO for Acer Aspire 3830TG
ALSA: ac97: Add ID for TI TLV320AIC27 codec
ASoC: imx-sgtl5000: Fix uninitialized pointer use in error path
ASoC: imx-sgtl5000: do not use devres on a foreign device
ASoC: blackfin: Add missing break statement to bf6xx
ASoC: 88pm860x: array overflow in snd_soc_put_volsw_2r_st()
ASoC: ab8500-codec: info leak in anc_status_control_put()
ASoC: max98095: a couple array underflows
ASoC: core: Only add platform DAI widgets once.
Pull pin control fixes from Linus Walleij:
- Various build warning fixes.
- Correct the S5P pin count.
- Handle BIAS_DEFAULT properly in the Palmas driver.
* tag 'pinctrl-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: palmas: do not abort pin configuration for BIAS_DEFAULT
pinctrl: Correct number of pins for s5pv210
pinctrl: remove an unnecessary cast
pinctrl: fix pinconf_dbg_config_write return type
pinctrl: tegra114: Remove MODULE_ALIAS
* pm-fixes:
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
Added id, bindings and comments for Holtek USB ID 04d9:a081 SHARKOON
DarkGlider Gaming mouse to use the same corrections of the report
descriptor as Holtek 04d9:a04a. As the mouse exceed HID_MAX_USAGES
at the same offsets in the reported descriptor.
Tested on the hardware.
Signed-off-by: Anders F. U. Kiær <ablacksheep@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch changes transport_alloc_session_tags() to fall back to
use vzalloc when kzalloc fails for big tag_num that end up generating
larger order allocations.
Also use is_vmalloc_addr() in transport_alloc_session_tags() failure
path, and normal transport_free_session() path to determine when
vfree() needs to be called instead of kfree().
v2 changes:
- Use __GFP_NOWARN | __GFP_REPEAT for sess_cmd_map kzalloc (mst)
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix GFP_KERNEL -> GFP_ATOMIC usage of percpu_ida_alloc() within
vhost_scsi_get_tag(), as this code is expected to be called directly
from interrupt context.
v2 changes:
- Handle possible tag < 0 failure with GFP_ATOMIC
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Asias He <asias@redhat.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where ib_destroy_cm_id() was incorrectly being called
after srpt_destroy_ch_ib() had destroyed the active QP.
This would result in the following failed SRP_LOGIN_REQ messages:
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1762bd, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c903009f8f41)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1758f9, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c903009f8f42)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff175941, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c90300a3cfb2)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
Reported-by: Navin Ahuja <navin.ahuja@saratoga-speed.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Felipe writes:
usb: fixes for v3.12-rc4
Here are some more fixes to musb's OTG support and a regression
caused on latest merge window; pxa25x_udc and gpio-vbus learned
to cope with deferred probe; s3c-hsotg got a fix for non-periodic
endpoints write size and f_fs got an error handling fix for cases
where ffs_do_descs() fail.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Commit caf5c03f (ACPI: Move acpi_bus_get_device() from bus.c to
scan.c) caused acpi_bus_get_device() to be exported using
EXPORT_SYMBOL_GPL(), but that broke some binary drivers in
existence, so revert that change.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When sysfs for no_turbo is set, then also some p states in turbo regions
are observed. This patch will set IDA Engage bit when no_turbo is set to
explicitly disengage turbo.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking changes from David Miller:
1) Multiply in netfilter IPVS can overflow when calculating destination
weight. From Simon Kirby.
2) Use after free fixes in IPVS from Julian Anastasov.
3) SFC driver bug fixes from Daniel Pieczko.
4) Memory leak in pcan_usb_core failure paths, from Alexey Khoroshilov.
5) Locking and encapsulation fixes to serial line CAN driver, from
Andrew Naujoks.
6) Duplex and VF handling fixes to bnx2x driver from Yaniv Rosner,
Eilon Greenstein, and Ariel Elior.
7) In lapb, if no other packets are outstanding, T1 timeouts actually
stall things and no packet gets sent. Fix from Josselin Costanzi.
8) ICMP redirects should not make it to the socket error queues, from
Duan Jiong.
9) Fix bugs in skge DMA mapping error handling, from Nikulas Patocka.
10) Fix setting of VLAN priority field on via-rhine driver, from Roget
Luethi.
11) Fix TX stalls and VLAN promisc programming in be2net driver from
Ajit Khaparde.
12) Packet padding doesn't get handled correctly in new usbnet SG
support code, from Ming Lei.
13) Fix races in netdevice teardown wrt. network namespace closing.
From Eric W. Biederman.
14) Fix potential missed initialization of net_secret if not TCP
connections are openned. From Eric Dumazet.
15) Cinterion PLXX product ID in qmi_wwan driver is wrong, from
Aleksander Morgado.
16) skb_cow_head() can change skb->data and thus packet header pointers,
don't use stale ip_hdr reference in ip_tunnel code.
17) Backend state transition handling fixes in xen-netback, from Paul
Durrant.
18) Packet offset for AH protocol is handled wrong in flow dissector,
from Eric Dumazet.
19) Taking down an fq packet scheduler instance can leave stale packets
in the queues, fix from Eric Dumazet.
20) Fix performance regressions introduced by TCP Small Queues. From
Eric Dumazet.
21) IPV6 GRE tunneling code calculates max_headroom incorrectly, from
Hannes Frederic Sowa.
22) Multicast timer handlers in ipv4 and ipv6 can be the last and final
reference to the ipv4/ipv6 specific network device state, so use the
reference put that will check and release the object if the
reference hits zero. From Salam Noureddine.
23) Fix memory corruption in ip_tunnel driver, and use skb_push()
instead of __skb_push() so that similar bugs are less hard to find.
From Steffen Klassert.
24) Add forgotten hookup of rtnl_ops in SIT and ip6tnl drivers, from
Nicolas Dichtel.
25) fq scheduler doesn't accurately rate limit in certain circumstances,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
pkt_sched: fq: rate limiting improvements
ip6tnl: allow to use rtnl ops on fb tunnel
sit: allow to use rtnl ops on fb tunnel
ip_tunnel: Remove double unregister of the fallback device
ip_tunnel_core: Change __skb_push back to skb_push
ip_tunnel: Add fallback tunnels to the hash lists
ip_tunnel: Fix a memory corruption in ip_tunnel_xmit
qlcnic: Fix SR-IOV configuration
ll_temac: Reset dma descriptors indexes on ndo_open
skbuff: size of hole is wrong in a comment
ipv6 mcast: use in6_dev_put in timer handlers instead of __in6_dev_put
ipv4 igmp: use in_dev_put in timer handlers instead of __in_dev_put
ethernet: moxa: fix incorrect placement of __initdata tag
ipv6: gre: correct calculation of max_headroom
powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file
Revert "powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file"
bonding: Fix broken promiscuity reference counting issue
tcp: TSQ can use a dynamic limit
dm9601: fix IFF_ALLMULTI handling
pkt_sched: fq: qdisc dismantle fixes
...
Pull sparc fix from David Miller:
"Just a single bug fix to a regression added during some strlcpy()
conversions"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix buggy strlcpy() conversion in ldom_reboot().
During driver loading we are initializing rps.vlv_work in
valleyview_enable_rps() via the rps.delayed_resume_work delayed work.
This is too late since we are using vlv_work already via
i915_driver_load()->intel_uncore_sanitize()->
intel_disable_gt_powersave(). This at least leads to the following
kernel warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Fix this by initialzing vlv_work before we call intel_uncore_sanitize().
The regression was introduced in
commit 7dcd2677ea
Author: Konstantin Khlebnikov <khlebnikov@openvz.org>
Date: Wed Jul 17 10:22:58 2013 +0400
drm/i915: fix long-standing SNB regression in power consumption
after resume
though there was no good reason to initialize the static vlv_work from
another delayed work to begin with (especially since this will happen
multiple times).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69397
Tested-by: shui yangwei <yangweix.shui@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull vfs lru leak fix from Al Viro:
"The fix in "super: fix for destroy lrus" didn't - they need to be
destroyed, all right, but that's the wrong place..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/super.c: fix lru_list leak for real
Pull two KVM fixes from Gleb Natapov.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: do not check bit 12 of EPT violation exit qualification when undefined
ARM: kvm: rename cpu_reset to avoid name clash
Freeing ->s_{inode,dentry}_lru in deactivate_locked_super() is wrong;
the right place is destroy_super(). As it is, we leak them if sget()
decides that new superblock it has allocated (and never shown to
anybody) isn't needed and should be freed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If the property was not specified then the returned resource had a
resource_size(..) == 1, rather than 0. The PCI-E driver checks for 0 so it
blindly continues on with a corrupted resource.
The regression was introduced into v3.12 by:
11be654 PCI: mvebu: Adapt to the new device tree layout
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
rtnl ops where introduced by c075b13098 ("ip6tnl: advertise tunnel param via
rtnl"), but I forget to assign rtnl ops to fb tunnels.
Now that it is done, we must remove the explicit call to
unregister_netdevice_queue(), because the fallback tunnel is added to the queue
in ip6_tnl_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this
is valid since commit 0bd8762824 ("ip6tnl: add x-netns support")).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl ops where introduced by ba3e3f50a0 ("sit: advertise tunnel param via
rtnl"), but I forget to assign rtnl ops to fb tunnels.
Now that it is done, we must remove the explicit call to
unregister_netdevice_queue(), because the fallback tunnel is added to the queue
in sit_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this
is valid since commit 5e6700b3bf ("sit: add support of x-netns")).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queueing the netdevices for removal, we queue the
fallback device twice in ip_tunnel_destroy(). The first
time when we queue all netdevices in the namespace and
then again explicitly. Fix this by removing the explicit
queueing of the fallback device.
Bug was introduced when network namespace support was added
with commit 6c742e714d ("ipip: add x-netns support").
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Git commit 0e6fbc5b ("ip_tunnels: extend iptunnel_xmit()")
moved the IP header installation to iptunnel_xmit() and
changed skb_push() to __skb_push(). This makes possible
bugs hard to track down, so change it back to skb_push().
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we can not update the tunnel parameters of
the fallback tunnels because we don't find them in the
hash lists. Fix this by adding them on initialization.
Bug was introduced with commit c544193214
("GRE: Refactor GRE tunneling code.")
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We might extend the used aera of a skb beyond the total
headroom when we install the ipip header. Fix this by
calling skb_cow_head() unconditionally.
Bug was introduced with commit c544193214
("GRE: Refactor GRE tunneling code.")
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter/IPVS fixes for your net
tree, they are:
* Fix BUG_ON splat due to malformed TCP packets seen by synproxy, from
Patrick McHardy.
* Fix possible weight overflow in lblc and lblcr schedulers due to
32-bits arithmetics, from Simon Kirby.
* Fix possible memory access race in the lblc and lblcr schedulers,
introduced when it was converted to use RCU, two patches from
Julian Anastasov.
* Fix hard dependency on CPU 0 when reading per-cpu stats in the
rate estimator, from Julian Anastasov.
* Fix race that may lead to object use after release, when invoking
ipvsadm -C && ipvsadm -R, introduced when adding RCU, from Julian
Anastasov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o Interface needs to be brought down and up while configuring SR-IOV.
Protect interface up/down using rtnl_lock()/rtnl_unlock()
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma descriptors indexes are only initialized on the probe function.
If a packet is on the buffer when temac_stop is called, the dma
descriptors indexes can be left on a incorrect state where no other
package can be sent.
So an interface could be left in an usable state after ifdow/ifup.
This patch makes sure that the descriptors indexes are in a proper
status when the device is open.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing dput(parent) is not valid in RCU walk mode. In RCU mode it would
probably be okay to update the parent flags, but it's actually not
necessary most of the time...
So only set the FUSE_I_ADVISE_RDPLUS flag on the parent when the entry was
recently initialized by READDIRPLUS.
This is achieved by setting FUSE_I_INIT_RDPLUS on entries added by
READDIRPLUS and only dropping out of RCU mode if this flag is set.
FUSE_I_INIT_RDPLUS is cleared once the FUSE_I_ADVISE_RDPLUS flag is set in
the parent.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
If revalidate finds an invalid dentry in RCU walk mode, let the VFS deal
with it instead of calling check_submounts_and_drop() which is not prepared
for being called from RCU walk.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Value of can_write variable in s3c_hsotg_write_fifo function should be limited
to 512 only for non-periodic endpoints. There was some discrepancy between
comment and code, because comment suggests correct behavior, but in the code
limit was applied to periodic endpoints too. So there is additional check
causing the limitation concerns only non-periodic endpoints.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch add missing error check in ffs_func_bind() function, after
ffs_do_descs() function call for high speed descriptors. Without this
check it's possible that the module will try dereference incorrect
pointer.
[ balbi@ti.com : removed trailing empty line ]
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This went unnoticed in durin the merge window:
The dsps driver creates a child device for the musb core driver _and_
attaches the of_node to it so devm_usb_get_phy_by_phandle() grabs the
correct phy and attaches the devm resources to the proper device. We
could also use the parent device but then devm would attach the
resource to the wrong device and it would be destroyed once the parent
device is gone - not the device that is used by the musb core driver.
If the phy is now not available then dsps_musb_init() /
devm_usb_get_phy_by_phandle() returns with EPROBE_DEFER. Since the
of_node is attached it tries OF drivers as well and matches the driver
against DSPS. That one creates a new child device for the musb core
driver which gets probed immediately.
The whole thing repeats itself until the stack overflows.
I belive the same problem exists in ux500 glue code (since 313bdb11
("usb: musb: ux500: add device tree probing support") but the drivers are
now probed in the right order so they don't see it.
The problem is that the dsps driver gets bound to the musb-child device
due to the same of_node / matching binding. I don't really agree with
having yet another child node in DT to fix this. Ideally we would have
musb core driver with DT bindings and according to the binding we would
select the few extra hacks / gleue layer.
Therefore I suggest the driver to reject the musb-core device.
Cc: Lee Jones <lee.jones@linaro.org>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The OMAP GPIO controller HW requires a pin to be configured in GPIO
input mode in order to operate as an interrupt input. Since drivers
should not be aware of whether an interrupt pin is also a GPIO or not,
the HW should be fully configured/enabled as an IRQ if a driver solely
uses IRQ APIs such as request_irq(), and never calls any GPIO-related
APIs. As such, add the missing HW setup to the OMAP GPIO controller's
irq_chip driver.
Since this bypasses the GPIO subsystem we have to ensure that another
driver won't be able to request the same GPIO pin that is used as an
IRQ and set its direction as output. Requesting the GPIO and setting
its direction as input is allowed though.
This fixes smsc911x ethernet support for tobi and igep OMAP3 boards
and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit facd8b80c6
("irq: Sanitize invoke_softirq") converted irq exit
calls of do_softirq() to __do_softirq() on all architectures,
assuming it was only used there for its irq disablement
properties.
But as a side effect, the softirqs processed in the end
of the hardirq are always called on the inline current
stack that is used by irq_exit() instead of the softirq
stack provided by the archs that override do_softirq().
The result is mostly safe if the architecture runs irq_exit()
on a separate irq stack because then softirqs are processed
on that same stack that is near empty at this stage (assuming
hardirq aren't nesting).
Otherwise irq_exit() runs in the task stack and so does the softirq
too. The interrupted call stack can be randomly deep already and
the softirq can dig through it even further. To add insult to the
injury, this softirq can be interrupted by a new hardirq, maximizing
the chances for a stack overrun as reported in powerpc for example:
do_IRQ: stack overflow: 1920
CPU: 0 PID: 1602 Comm: qemu-system-ppc Not tainted 3.10.4-300.1.fc19.ppc64p7 #1
Call Trace:
[c0000000050a8740] .show_stack+0x130/0x200 (unreliable)
[c0000000050a8810] .dump_stack+0x28/0x3c
[c0000000050a8880] .do_IRQ+0x2b8/0x2c0
[c0000000050a8930] hardware_interrupt_common+0x154/0x180
--- Exception: 501 at .cp_start_xmit+0x3a4/0x820 [8139cp]
LR = .cp_start_xmit+0x390/0x820 [8139cp]
[c0000000050a8d40] .dev_hard_start_xmit+0x394/0x640
[c0000000050a8e00] .sch_direct_xmit+0x110/0x260
[c0000000050a8ea0] .dev_queue_xmit+0x260/0x630
[c0000000050a8f40] .br_dev_queue_push_xmit+0xc4/0x130 [bridge]
[c0000000050a8fc0] .br_dev_xmit+0x198/0x270 [bridge]
[c0000000050a9070] .dev_hard_start_xmit+0x394/0x640
[c0000000050a9130] .dev_queue_xmit+0x428/0x630
[c0000000050a91d0] .ip_finish_output+0x2a4/0x550
[c0000000050a9290] .ip_local_out+0x50/0x70
[c0000000050a9310] .ip_queue_xmit+0x148/0x420
[c0000000050a93b0] .tcp_transmit_skb+0x4e4/0xaf0
[c0000000050a94a0] .__tcp_ack_snd_check+0x7c/0xf0
[c0000000050a9520] .tcp_rcv_established+0x1e8/0x930
[c0000000050a95f0] .tcp_v4_do_rcv+0x21c/0x570
[c0000000050a96c0] .tcp_v4_rcv+0x734/0x930
[c0000000050a97a0] .ip_local_deliver_finish+0x184/0x360
[c0000000050a9840] .ip_rcv_finish+0x148/0x400
[c0000000050a98d0] .__netif_receive_skb_core+0x4f8/0xb00
[c0000000050a99d0] .netif_receive_skb+0x44/0x110
[c0000000050a9a70] .br_handle_frame_finish+0x2bc/0x3f0 [bridge]
[c0000000050a9b20] .br_nf_pre_routing_finish+0x2ac/0x420 [bridge]
[c0000000050a9bd0] .br_nf_pre_routing+0x4dc/0x7d0 [bridge]
[c0000000050a9c70] .nf_iterate+0x114/0x130
[c0000000050a9d30] .nf_hook_slow+0xb4/0x1e0
[c0000000050a9e00] .br_handle_frame+0x290/0x330 [bridge]
[c0000000050a9ea0] .__netif_receive_skb_core+0x34c/0xb00
[c0000000050a9fa0] .netif_receive_skb+0x44/0x110
[c0000000050aa040] .napi_gro_receive+0xe8/0x120
[c0000000050aa0c0] .cp_rx_poll+0x31c/0x590 [8139cp]
[c0000000050aa1d0] .net_rx_action+0x1dc/0x310
[c0000000050aa2b0] .__do_softirq+0x158/0x330
[c0000000050aa3b0] .irq_exit+0xc8/0x110
[c0000000050aa430] .do_IRQ+0xdc/0x2c0
[c0000000050aa4e0] hardware_interrupt_common+0x154/0x180
--- Exception: 501 at .bad_range+0x1c/0x110
LR = .get_page_from_freelist+0x908/0xbb0
[c0000000050aa7d0] .list_del+0x18/0x50 (unreliable)
[c0000000050aa850] .get_page_from_freelist+0x908/0xbb0
[c0000000050aa9e0] .__alloc_pages_nodemask+0x21c/0xae0
[c0000000050aaba0] .alloc_pages_vma+0xd0/0x210
[c0000000050aac60] .handle_pte_fault+0x814/0xb70
[c0000000050aad50] .__get_user_pages+0x1a4/0x640
[c0000000050aae60] .get_user_pages_fast+0xec/0x160
[c0000000050aaf10] .__gfn_to_pfn_memslot+0x3b0/0x430 [kvm]
[c0000000050aafd0] .kvmppc_gfn_to_pfn+0x64/0x130 [kvm]
[c0000000050ab070] .kvmppc_mmu_map_page+0x94/0x530 [kvm]
[c0000000050ab190] .kvmppc_handle_pagefault+0x174/0x610 [kvm]
[c0000000050ab270] .kvmppc_handle_exit_pr+0x464/0x9b0 [kvm]
[c0000000050ab320] kvm_start_lightweight+0x1ec/0x1fc [kvm]
[c0000000050ab4f0] .kvmppc_vcpu_run_pr+0x168/0x3b0 [kvm]
[c0000000050ab9c0] .kvmppc_vcpu_run+0xc8/0xf0 [kvm]
[c0000000050aba50] .kvm_arch_vcpu_ioctl_run+0x5c/0x1a0 [kvm]
[c0000000050abae0] .kvm_vcpu_ioctl+0x478/0x730 [kvm]
[c0000000050abc90] .do_vfs_ioctl+0x4ec/0x7c0
[c0000000050abd80] .SyS_ioctl+0xd4/0xf0
[c0000000050abe30] syscall_exit+0x0/0x98
Since this is a regression, this patch proposes a minimalistic
and low-risk solution by blindly forcing the hardirq exit processing of
softirqs on the softirq stack. This way we should reduce significantly
the opportunities for task stack overflow dug by softirqs.
Longer term solutions may involve extending the hardirq stack coverage to
irq_exit(), etc...
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: #3.9.. <stable@vger.kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@au1.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@au1.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Since commit c93bdd0e03 ("netvm: allow skb allocation to use PFMEMALLOC
reserves"), hole size is one bit less than what is written in the comment.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the timer handlers to run after the call to
ipv6_mc_down so use in6_dev_put instead of __in6_dev_put in the
handler function in order to do proper cleanup when the refcnt
reaches 0. Otherwise, the refcnt can reach zero without the
inet6_dev being destroyed and we end up leaking a reference to
the net_device and see messages like the following,
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Tested on linux-3.4.43.
Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the timer handlers to run after the call to
ip_mc_down so use in_dev_put instead of __in_dev_put in the handler
function in order to do proper cleanup when the refcnt reaches 0.
Otherwise, the refcnt can reach zero without the in_device being
destroyed and we end up leaking a reference to the net_device and
see messages like the following,
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Tested on linux-3.4.43.
Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
In this particular case __initdata is incorrect as moxart_mac_driver
can be used after the driver gets initialized.
Also while at it static-ize moxart_mac_driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gre_hlen already accounts for sizeof(struct ipv6_hdr) + gre header,
so initialize max_headroom to zero. Otherwise the
if (encap_limit >= 0) {
max_headroom += 8;
mtu -= 8;
}
increments an uninitialized variable before max_headroom was reset.
Found with coverity: 728539
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 894116bd0e.
I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567
Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:
dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.
The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification. With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are. This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device. Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave. But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error
Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.
This is also needed for the ALLMULTI flag
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP Small Queues was added, we used a sysctl to limit amount of
packets queues on Qdisc/device queues for a given TCP flow.
Problem is this limit is either too big for low rates, or too small
for high rates.
Now TCP stack has rate estimation in sk->sk_pacing_rate, and TSO
auto sizing, it can better control number of packets in Qdisc/device
queues.
New limit is two packets or at least 1 to 2 ms worth of packets.
Low rates flows benefit from this patch by having even smaller
number of packets in queues, allowing for faster recovery,
better RTT estimations.
High rates flows benefit from this patch by allowing more than 2 packets
in flight as we had reports this was a limiting factor to reach line
rate. [ In particular if TX completion is delayed because of coalescing
parameters ]
Example for a single flow on 10Gbp link controlled by FQ/pacing
14 packets in flight instead of 2
$ tc -s -d qd
qdisc fq 8001: dev eth0 root refcnt 32 limit 10000p flow_limit 100p
buckets 1024 quantum 3028 initial_quantum 15140
Sent 1168459366606 bytes 771822841 pkt (dropped 0, overlimits 0
requeues 6822476)
rate 9346Mbit 771713pps backlog 953820b 14p requeues 6822476
2047 flow, 2046 inactive, 1 throttled, delay 15673 ns
2372 gc, 0 highprio, 0 retrans, 9739249 throttled, 0 flows_plimit
Note that sk_pacing_rate is currently set to twice the actual rate, but
this might be refined in the future when a flow is in congestion
avoidance.
Additional change : skb->destructor should be set to tcp_wfree().
A future patch (for linux 3.13+) might remove tcp_limit_output_bytes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan writes:
Second set of IIO fixes for the 3.12 cycle (take 2)
A few small fixes:
1) Make sure that debugfs entries are removed early enough to prevent
a race.
2) Drop a stray regulator_put from ad8366 left over from the devm_ patches.
3) The ST magnetometer driver had incorrect register addresses for the
actual data channels.
Commit f95499c303,
n_tty: Don't wait for buffer work in read() loop
creates a race window which can cause a pty master read()
to miss the last pty slave write(s) and return -EIO instead,
thus signalling the pty slave is closed. This can happen when
the pty slave is written and immediately closed but before the
tty buffer i/o loop receives the new input; the pty master
read() is scheduled, sees its read buffer is empty and the
pty slave has been closed, and exits.
Because tty_flush_to_ldisc() has significant performance impact
for parallel i/o, rather than revert the commit, special case this
condition (ie., when the read buffer is empty and the 'other' pty
has been closed) and, only then, wait for buffer work to complete
before re-testing if the read buffer is still empty.
As before, subsequent pty master reads return any available data
until no more data is available, and then returns -EIO to
indicate the pty slave has closed.
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn> (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: Michal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for Oopses in the pNFS files layout driver
- Fix a regression when doing a non-exclusive file create on NFSv4.x
- NFSv4.1 security negotiation fixes when looking up the root
filesystem
- Fix a memory ordering issue in the pNFS files layout driver
* tag 'nfs-for-3.12-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Give "flavor" an initial value to fix a compile warning
NFSv4.1: try SECINFO_NO_NAME flavs until one works
NFSv4.1: Ensure memory ordering between nfs4_ds_connect and nfs4_fl_prepare_ds
NFSv4.1: nfs4_fl_prepare_ds - fix bugs when the connect attempt fails
NFSv4: Honour the 'opened' parameter in the atomic_open() filesystem method
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
pidns: fix free_pid() to handle the first fork failure
ipc,msg: prevent race with rmid in msgsnd,msgrcv
ipc/sem.c: update sem_otime for all operations
mm/hwpoison: fix the lack of one reference count against poisoned page
mm/hwpoison: fix false report on 2nd attempt at page recovery
mm/hwpoison: fix test for a transparent huge page
mm/hwpoison: fix traversal of hugetlbfs pages to avoid printk flood
block: change config option name for cmdline partition parsing
mm/mlock.c: prevent walking off the end of a pagetable in no-pmd configuration
mm: avoid reinserting isolated balloon pages into LRU lists
arch/parisc/mm/fault.c: fix uninitialized variable usage
include/asm-generic/vtime.h: avoid zero-length file
nilfs2: fix issue with race condition of competition between segments for dirty blocks
Documentation/kernel-parameters.txt: replace kernelcore with Movable
mm/bounce.c: fix a regression where MS_SNAP_STABLE (stable pages snapshotting) was ignored
kernel/kmod.c: check for NULL in call_usermodehelper_exec()
ipc/sem.c: synchronize the proc interface
ipc/sem.c: optimize sem_lock()
ipc/sem.c: fix race in sem_lock()
mm/compaction.c: periodically schedule when freeing pages
...
"case 0" in free_pid() assumes that disable_pid_allocation() should
clear PIDNS_HASH_ADDING before the last pid goes away.
However this doesn't happen if the first fork() fails to create the
child reaper which should call disable_pid_allocation().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a race in both msgrcv() and msgsnd() between finding the msg
and actually dealing with the queue, as another thread can delete shmid
underneath us if we are preempted before acquiring the
kern_ipc_perm.lock.
Manfred illustrates this nicely:
Assume a preemptible kernel that is preempted just after
msq = msq_obtain_object_check(ns, msqid)
in do_msgrcv(). The only lock that is held is rcu_read_lock().
Now the other thread processes IPC_RMID. When the first task is
resumed, then it will happily wait for messages on a deleted queue.
Fix this by checking for if the queue has been deleted after taking the
lock.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reported-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: <stable@vger.kernel.org> [3.11]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 0a2b9d4c79 ("ipc/sem.c: move wake_up_process out of the
spinlock section"), the update of semaphore's sem_otime(last semop time)
was moved to one central position (do_smart_update).
But since do_smart_update() is only called for operations that modify
the array, this means that wait-for-zero semops do not update sem_otime
anymore.
The fix is simple:
Non-alter operations must update sem_otime.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Reported-by: Jia He <jiakernel@gmail.com>
Tested-by: Jia He <jiakernel@gmail.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lack of one reference count against poisoned page for hwpoison_inject
w/o hwpoison_filter enabled result in hwpoison detect -1 users still
referenced the page, however, the number should be 0 except the poison
handler held one after successfully unmap. This patch fix it by hold one
referenced count against poisoned page for hwpoison_inject w/ and w/o
hwpoison_filter enabled.
Before patch:
[ 71.902112] Injecting memory failure at pfn 224706
[ 71.902137] MCE 0x224706: dirty LRU page recovery: Failed
[ 71.902138] MCE 0x224706: dirty LRU page still referenced by -1 users
After patch:
[ 94.710860] Injecting memory failure at pfn 215b68
[ 94.710885] MCE 0x215b68: dirty LRU page recovery: Recovered
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the page is poisoned by software injection w/ MF_COUNT_INCREASED
flag, there is a false report during the 2nd attempt at page recovery
which is not truthful.
This patch fixes it by reporting the first attempt to try free buddy
page recovery if MF_COUNT_INCREASED is set.
Before patch:
[ 346.332041] Injecting memory failure at pfn 200010
[ 346.332189] MCE 0x200010: free buddy, 2nd try page recovery: Delayed
After patch:
[ 297.742600] Injecting memory failure at pfn 200010
[ 297.742941] MCE 0x200010: free buddy page recovery: Delayed
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PageTransHuge() can't guarantee the page is a transparent huge page
since it returns true for both transparent huge and hugetlbfs pages.
This patch fixes it by checking the page is also !hugetlbfs page.
Before patch:
[ 121.571128] Injecting memory failure at pfn 23a200
[ 121.571141] MCE 0x23a200: huge page recovery: Delayed
[ 140.355100] MCE: Memory failure is now running on 0x23a200
After patch:
[ 94.290793] Injecting memory failure at pfn 23a000
[ 94.290800] MCE 0x23a000: huge page recovery: Delayed
[ 105.722303] MCE: Software-unpoisoned page 0x23a000
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
madvise_hwpoison won't check if the page is small page or huge page and
traverses in small page granularity against the range unconditionally,
which result in a printk flood "MCE xxx: already hardware poisoned" if
the page is a huge page.
This patch fixes it by using compound_order(compound_head(page)) for
huge page iterator.
Testcase:
#define _GNU_SOURCE
#include <stdlib.h>
#include <stdio.h>
#include <sys/mman.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <errno.h>
#define PAGES_TO_TEST 3
#define PAGE_SIZE 4096 * 512
int main(void)
{
char *mem;
int i;
mem = mmap(NULL, PAGES_TO_TEST * PAGE_SIZE,
PROT_READ | PROT_WRITE, MAP_PRIVATE | MAP_ANONYMOUS | MAP_HUGETLB, 0, 0);
if (madvise(mem, PAGES_TO_TEST * PAGE_SIZE, MADV_HWPOISON) == -1)
return -1;
munmap(mem, PAGES_TO_TEST * PAGE_SIZE);
return 0;
}
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently commit bab55417b1 ("block: support embedded device command
line partition") introduced CONFIG_CMDLINE_PARSER. However, that name
is too generic and sounds like it enables/disables generic kernel boot
arg processing, when it really is block specific.
Before this option becomes a part of a full/final release, add the BLK_
prefix to it so that it is clear in absence of any other context that it
is block specific.
In addition, fix up the following less critical items:
- help text was not really at all helpful.
- index file for Documentation was not updated
- add the new arg to Documentation/kernel-parameters.txt
- clarify wording in source comments
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Cai Zhiyong <caizhiyong@huawei.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function __munlock_pagevec_fill() introduced in commit 7a8010cd36
("mm: munlock: manual pte walk in fast path instead of
follow_page_mask()") uses pmd_addr_end() for restricting its operation
within current page table.
This is insufficient on architectures/configurations where pmd is folded
and pmd_addr_end() just returns the end of the full range to be walked.
In this case, it allows pte++ to walk off the end of a page table
resulting in unpredictable behaviour.
This patch fixes the function by using pgd_addr_end() and pud_addr_end()
before pmd_addr_end(), which will yield correct page table boundary on
all configurations. This is similar to what existing page walkers do
when walking each level of the page table.
Additionaly, the patch clarifies a comment for get_locked_pte() call in the
function.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Cc: Jörn Engel <joern@logfs.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
patch(1) can't handle zero-length files - it appears to simply not create
the file, so my powerpc build fails.
Put something in here to make life easier.
Cc: Hugh Dickins <hughd@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many NILFS2 users were reported about strange file system corruption
(for example):
NILFS: bad btree node (blocknr=185027): level = 0, flags = 0x0, nchildren = 768
NILFS error (device sda4): nilfs_bmap_last_key: broken bmap (inode number=11540)
But such error messages are consequence of file system's issue that takes
place more earlier. Fortunately, Jerome Poulin <jeromepoulin@gmail.com>
and Anton Eliasson <devel@antoneliasson.se> were reported about another
issue not so recently. These reports describe the issue with segctor
thread's crash:
BUG: unable to handle kernel paging request at 0000000000004c83
IP: nilfs_end_page_io+0x12/0xd0 [nilfs2]
Call Trace:
nilfs_segctor_do_construct+0xf25/0x1b20 [nilfs2]
nilfs_segctor_construct+0x17b/0x290 [nilfs2]
nilfs_segctor_thread+0x122/0x3b0 [nilfs2]
kthread+0xc0/0xd0
ret_from_fork+0x7c/0xb0
These two issues have one reason. This reason can raise third issue
too. Third issue results in hanging of segctor thread with eating of
100% CPU.
REPRODUCING PATH:
One of the possible way or the issue reproducing was described by
Jermoe me Poulin <jeromepoulin@gmail.com>:
1. init S to get to single user mode.
2. sysrq+E to make sure only my shell is running
3. start network-manager to get my wifi connection up
4. login as root and launch "screen"
5. cd /boot/log/nilfs which is a ext3 mount point and can log when NILFS dies.
6. lscp | xz -9e > lscp.txt.xz
7. mount my snapshot using mount -o cp=3360839,ro /dev/vgUbuntu/root /mnt/nilfs
8. start a screen to dump /proc/kmsg to text file since rsyslog is killed
9. start a screen and launch strace -f -o find-cat.log -t find
/mnt/nilfs -type f -exec cat {} > /dev/null \;
10. start a screen and launch strace -f -o apt-get.log -t apt-get update
11. launch the last command again as it did not crash the first time
12. apt-get crashes
13. ps aux > ps-aux-crashed.log
13. sysrq+W
14. sysrq+E wait for everything to terminate
15. sysrq+SUSB
Simplified way of the issue reproducing is starting kernel compilation
task and "apt-get update" in parallel.
REPRODUCIBILITY:
The issue is reproduced not stable [60% - 80%]. It is very important to
have proper environment for the issue reproducing. The critical
conditions for successful reproducing:
(1) It should have big modified file by mmap() way.
(2) This file should have the count of dirty blocks are greater that
several segments in size (for example, two or three) from time to time
during processing.
(3) It should be intensive background activity of files modification
in another thread.
INVESTIGATION:
First of all, it is possible to see that the reason of crash is not valid
page address:
NILFS [nilfs_segctor_complete_write]:2100 bh->b_count 0, bh->b_blocknr 13895680, bh->b_size 13897727, bh->b_page 0000000000001a82
NILFS [nilfs_segctor_complete_write]:2101 segbuf->sb_segnum 6783
Moreover, value of b_page (0x1a82) is 6786. This value looks like segment
number. And b_blocknr with b_size values look like block numbers. So,
buffer_head's pointer points on not proper address value.
Detailed investigation of the issue is discovered such picture:
[-----------------------------SEGMENT 6783-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_segctor_do_construct]:2336 nilfs_segctor_assign
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111149024, segbuf->sb_segnum 6783
[-----------------------------SEGMENT 6784-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_lookup_dirty_data_buffers]:782 bh->b_count 1, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_lookup_dirty_data_buffers]:783 bh->b_assoc_buffers.next ffff8802174a6798, bh->b_assoc_buffers.prev ffff880221cffee8
NILFS [nilfs_segctor_do_construct]:2336 nilfs_segctor_assign
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bh]:575 bh->b_count 1, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_segbuf_submit_bh]:576 segbuf->sb_segnum 6784
NILFS [nilfs_segbuf_submit_bh]:577 bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880218bcdf50
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111150080, segbuf->sb_segnum 6784, segbuf->sb_nbio 0
[----------] ditto
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111164416, segbuf->sb_segnum 6784, segbuf->sb_nbio 15
[-----------------------------SEGMENT 6785-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_lookup_dirty_data_buffers]:782 bh->b_count 2, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_lookup_dirty_data_buffers]:783 bh->b_assoc_buffers.next ffff880219277e80, bh->b_assoc_buffers.prev ffff880221cffc88
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bh]:575 bh->b_count 2, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_segbuf_submit_bh]:576 segbuf->sb_segnum 6785
NILFS [nilfs_segbuf_submit_bh]:577 bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880222cc7ee8
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111165440, segbuf->sb_segnum 6785, segbuf->sb_nbio 0
[----------] ditto
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111177728, segbuf->sb_segnum 6785, segbuf->sb_nbio 12
NILFS [nilfs_segctor_do_construct]:2399 nilfs_segctor_wait
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6783
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6784
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6785
NILFS [nilfs_segctor_complete_write]:2100 bh->b_count 0, bh->b_blocknr 13895680, bh->b_size 13897727, bh->b_page 0000000000001a82
BUG: unable to handle kernel paging request at 0000000000001a82
IP: [<ffffffffa024d0f2>] nilfs_end_page_io+0x12/0xd0 [nilfs2]
Usually, for every segment we collect dirty files in list. Then, dirty
blocks are gathered for every dirty file, prepared for write and
submitted by means of nilfs_segbuf_submit_bh() call. Finally, it takes
place complete write phase after calling nilfs_end_bio_write() on the
block layer. Buffers/pages are marked as not dirty on final phase and
processed files removed from the list of dirty files.
It is possible to see that we had three prepare_write and submit_bio
phases before segbuf_wait and complete_write phase. Moreover, segments
compete between each other for dirty blocks because on every iteration
of segments processing dirty buffer_heads are added in several lists of
payload_buffers:
[SEGMENT 6784]: bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880218bcdf50
[SEGMENT 6785]: bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880222cc7ee8
The next pointer is the same but prev pointer has changed. It means
that buffer_head has next pointer from one list but prev pointer from
another. Such modification can be made several times. And, finally, it
can be resulted in various issues: (1) segctor hanging, (2) segctor
crashing, (3) file system metadata corruption.
FIX:
This patch adds:
(1) setting of BH_Async_Write flag in nilfs_segctor_prepare_write()
for every proccessed dirty block;
(2) checking of BH_Async_Write flag in
nilfs_lookup_dirty_data_buffers() and
nilfs_lookup_dirty_node_buffers();
(3) clearing of BH_Async_Write flag in nilfs_segctor_complete_write(),
nilfs_abort_logs(), nilfs_forget_buffer(), nilfs_clear_dirty_page().
Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Reported-by: Anton Eliasson <devel@antoneliasson.se>
Cc: Paul Fertser <fercerpav@gmail.com>
Cc: ARAI Shun-ichi <hermes@ceres.dti.ne.jp>
Cc: Piotr Szymaniak <szarpaj@grubelek.pl>
Cc: Juan Barry Manuel Canham <Linux@riotingpacifist.net>
Cc: Zahid Chowdhury <zahid.chowdhury@starsolutions.com>
Cc: Elmer Zhang <freeboy6716@gmail.com>
Cc: Kenneth Langga <klangga@gmail.com>
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "force" parameter in __blk_queue_bounce was being ignored, which
means that stable page snapshots are not always happening (on ext3).
This of course leads to DIF disks reporting checksum errors, so fix this
regression.
The regression was introduced in commit 6bc454d150 ("bounce: Refactor
__blk_queue_bounce to not use bi_io_vec")
Reported-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If /proc/sys/kernel/core_pattern contains only "|", a NULL pointer
dereference happens upon core dump because argv_split("") returns
argv[0] == NULL.
This bug was once fixed by commit 264b83c07a ("usermodehelper: check
subprocess_info->path != NULL") but was by error reintroduced by commit
7f57cfa4e2 ("usermodehelper: kill the sub_info->path[0] check").
This bug seems to exist since 2.6.19 (the version which core dump to
pipe was added). Depending on kernel version and config, some side
effect might happen immediately after this oops (e.g. kernel panic with
2.6.32-358.18.1.el6).
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The proc interface is not aware of sem_lock(), it instead calls
ipc_lock_object() directly. This means that simple semop() operations
can run in parallel with the proc interface. Right now, this is
uncritical, because the implementation doesn't do anything that requires
a proper synchronization.
But it is dangerous and therefore should be fixed.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Operations that need access to the whole array must guarantee that there
are no simple operations ongoing. Right now this is achieved by
spin_unlock_wait(sem->lock) on all semaphores.
If complex_count is nonzero, then this spin_unlock_wait() is not
necessary, because it was already performed in the past by the thread
that increased complex_count and even though sem_perm.lock was dropped
inbetween, no simple operation could have started, because simple
operations cannot start when complex_count is non-zero.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The exclusion of complex operations in sem_lock() is insufficient: after
acquiring the per-semaphore lock, a simple op must first check that
sem_perm.lock is not locked and only after that test check
complex_count. The current code does it the other way around - and that
creates a race. Details are below.
The patch is a complete rewrite of sem_lock(), based in part on the code
from Mike Galbraith. It removes all gotos and all loops and thus the
risk of livelocks.
I have tested the patch (together with the next one) on my i3 laptop and
it didn't cause any problems.
The bug is probably also present in 3.10 and 3.11, but for these kernels
it might be simpler just to move the test of sma->complex_count after
the spin_is_locked() test.
Details of the bug:
Assume:
- sma->complex_count = 0.
- Thread 1: semtimedop(complex op that must sleep)
- Thread 2: semtimedop(simple op).
Pseudo-Trace:
Thread 1: sem_lock(): acquire sem_perm.lock
Thread 1: sem_lock(): check for ongoing simple ops
Nothing ongoing, thread 2 is still before sem_lock().
Thread 1: try_atomic_semop()
<<< preempted.
Thread 2: sem_lock():
static inline int sem_lock(struct sem_array *sma, struct sembuf *sops,
int nsops)
{
int locknum;
again:
if (nsops == 1 && !sma->complex_count) {
struct sem *sem = sma->sem_base + sops->sem_num;
/* Lock just the semaphore we are interested in. */
spin_lock(&sem->lock);
/*
* If sma->complex_count was set while we were spinning,
* we may need to look at things we did not lock here.
*/
if (unlikely(sma->complex_count)) {
spin_unlock(&sem->lock);
goto lock_array;
}
<<<<<<<<<
<<< complex_count is still 0.
<<<
<<< Here it is preempted
<<<<<<<<<
Thread 1: try_atomic_semop() returns, notices that it must sleep.
Thread 1: increases sma->complex_count.
Thread 1: drops sem_perm.lock
Thread 2:
/*
* Another process is holding the global lock on the
* sem_array; we cannot enter our critical section,
* but have to wait for the global lock to be released.
*/
if (unlikely(spin_is_locked(&sma->sem_perm.lock))) {
spin_unlock(&sem->lock);
spin_unlock_wait(&sma->sem_perm.lock);
goto again;
}
<<< sem_perm.lock already dropped, thus no "goto again;"
locknum = sops->sem_num;
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've been getting warnings about an excessive amount of time spent
allocating pages for migration during memory compaction without
scheduling. isolate_freepages_block() already periodically checks for
contended locks or the need to schedule, but isolate_freepages() never
does.
When a zone is massively long and no suitable targets can be found, this
iteration can be quite expensive without ever doing cond_resched().
Check periodically for the need to reschedule while the compaction free
scanner iterates.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A high setting of max_map_count, and a process core-dumping with a large
enough vm_map_count could result in an NT_FILE note not being written,
and the kernel crashing immediately later because it has assumed
otherwise.
Reproduction of the oops-causing bug described here:
https://lkml.org/lkml/2013/8/30/50
Rge ussue originated in commit 2aa362c49c ("coredump: extend core dump
note section to contain file names of mapped file") from Oct 4, 2012.
This patch make that section optional in that case. fill_files_note()
should signify the error, and also let the info struct in
elf_core_dump() be zero-initialized so that we can check for the
optionally written note.
[akpm@linux-foundation.org: avoid abusing E2BIG, remove a couple of not-really-needed local variables]
[akpm@linux-foundation.org: fix sparse warning]
Signed-off-by: Dan Aloni <alonid@stratoscale.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Tested-by: Martin MOKREJS <mmokrejs@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the the debugfs entries in iio_device_unregister(). Otherwise the debugfs
entries might still be accessible even though the device used in the debugfs
callback has already been freed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
fq_reset() should drops all packets in queue, including
throttled flows.
This patch moves code from fq_destroy() to fq_reset()
to do the cleaning.
fq_change() must stop calling fq_dequeue() if all remaining
packets are from throttled flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8ed781668d ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.
This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the scenario where an IPv6 router is advertising a fixed
preferred_lft of 1800 seconds, while the valid_lft begins at 3600
seconds and counts down in realtime.
A client should reset its preferred_lft to 1800 every time the RA is
received, but a bug is causing Linux to ignore the update.
The core problem is here:
if (prefered_lft != ifp->prefered_lft) {
Note that ifp->prefered_lft is an offset, so it doesn't decrease over
time. Thus, the comparison is always (1800 != 1800), which fails to
trigger an update.
The most direct solution would be to compute a "stored_prefered_lft",
and use that value in the comparison. But I think that trying to filter
out unnecessary updates here is a premature optimization. In order for
the filter to apply, both of these would need to hold:
- The advertised valid_lft and preferred_lft are both declining in
real time.
- No clock skew exists between the router & client.
So in this patch, I've set "update_lft = 1" unconditionally, which
allows the surrounding code to be greatly simplified.
Signed-off-by: Paul Marks <pmarks@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While sending packet skb_cow_head() can change skb header which
invalidates inner_iph pointer to skb header. Following patch
avoid using it. Found by code inspection.
This bug was introduced by commit 0e6fbc5b6c (ip_tunnels: extend
iptunnel_xmit()).
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of RCU api makes vxlan code easier to understand. It also
fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference.
In rare case without ACCESS_ONCE() compiler might omit vs on
sk_user_data dereference.
Compiler can use vs as alias for sk->sk_user_data, resulting in
multiple sk_user_data dereference in rcu read context which
could change.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull regulator fixes from Mark Brown:
"Quite a few fixes here, mostly small driver specific ones.
The stand out thing is a fix for errors generating the documentation
from Randy Dunlap, otherwise unless you're using the driver in
question there should be no impact"
* tag 'regulator-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: ti-abb: Fix bias voltage glitch in transition to bypass mode
regulator: wm831x-ldo: Fix max_uV for gp_ldo and aldo linear range settings
regulator: wm8350: correct the max_uV of LDO
regulator: fix fatal kernel-doc error
regulator: palmas: Remove wrong comment for the equation calculating num_voltages
regulator: da9063: Fix PTR_ERR/ERR_PTR mismatch
regulator: palmas: configure enable time for LDOs
regulator: palmas: fix the n_voltages for smps to 122
Pull apparmor fixes from James Morris:
"Bugfixes for the Apparmor code for regressions introduced in the 3.12
pull request"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
apparmor: fix suspicious RCU usage warning in policy.c/policy.h
apparmor: Use shash crypto API interface for profile hashes
Pull assorted vfs fixes from Al Viro:
"A couple of bug fixes + removal of dead code in afs ->d_revalidate()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: dget_parent() can't return a negative dentry
ocfs2: needs ->d_lock to poke in ->d_parent->d_inode from ->d_revalidate()
sysv: Add forgotten superblock lock init for v7 fs
Since the patch "cpufreq: cpufreq-cpu0: NULL is a valid regulator", cpu_reg
contains an error value if the regulator is not set, instead of NULL.
Accordingly, fix the remaining check for non-NULL cpu_reg.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'clk_round_rate' returns a negative error code upon failure. This
will never get detected by unsigned 'newfreq'. Make it signed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Recent commit 8fd37a4 (PM / hibernate: Create memory bitmaps after
freezing user space) broke the resume part of the user space driven
hibernation (s2disk), because I forgot that the resume utility
loaded the image into memory without freezing user space (it still
freezes tasks after loading the image). This means that during user
space driven resume we need to create the memory bitmaps at the
"device open" time rather than at the "freeze tasks" time, so make
that happen (that's a special case anyway, so it needs to be treated
in a special way).
Reported-and-tested-by: Ronald <ronald645@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull AVR32 fixes from Hans-Christian Egtvedt.
Fix build warnings and use the Kbuild infrastructure for generic headers
rather than doing it by hand.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: cast syscall_return to silence compiler warning
avr32: fix clockevents kernel warning
avr32: use Kbuild infrastructure to handle the asm-generic headers
Pull S+core fixes from Lennox Wu:
"These updates include updating information of maintainers, fix some
trivial errors, and add a necessary function for supporting ipv6"
* tag 'for-linus-20130929' of git://github.com/sctscore/official-linux:
Score: Update the information of Score maintaners
Score: Modify the Makefile of Score, remove -mlong-calls for compiling
Score: Implement the function csum_ipv6_magic
Score: The commit is for compiling successfully
Pull ARC Fixes from Vineet Gupta:
- Handle unaligned access in zero delay loops
- spinlock livelock fix for SMP systemC model
- fix 32bit overflow in access_ok
- better setup of clockevents
* tag 'arc-fixes-for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Use clockevents_config_and_register over clockevents_register_device
ARC: Workaround spinlock livelock in SMP SystemC simulation
ARC: Fix 32-bit wrap around in access_ok()
ARC: Handle zero-overhead-loop in unaligned access handler
Like we are doing on DDR0 we need to cleanly shutdown DDR1 if it is
used before rebooting.
If DDR1 is not initialized, we check it and avoid dereferencing its address.
Even by adding two more instructions, we are able to complete the procedure
within a single cache line.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Change my email to kernel.org which is easier for me to catch.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Take more drivers into maintain list of CSR SiRF SoC machines.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
HWMOD removal for MMC is breaking edma_start as the events are being manually
triggered due to unused channel list not being clear.
The above issue is fixed by reading the "dmas" property from the DT node if it
exists and clearing the bits in the unused channel list if the dma controller
used by any device is EDMA. For this purpose we use the of_* helpers to parse
the arguments in the dmas phandle list.
Also introduced is a minor clean up of a checkpatch error in old code.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reported-by: Balaji T K <balajitk@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pantel Antoniou <panto@antoniou-consulting.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On the TC2 testchip, when all CPUs in a cluster enter standbywfi
and commit a power down request, the power controller will wait
for standbywfil2 coming from L2 cache controller to shut the
cluster down.
By the time all CPUs in a cluster commit a power down request
and enter wfi, the power controller cannot backtrack, or put it
another way, a CPU must not be allowed to complete execution
independently of the power controller, the only way for it to
resume properly must be upon wake-up IRQ pending and subsequent
reset triggered from the power controller.
Current MCPM back-end for TC2 disables the GIC CPU IF only when
power down is committed through the tc2_pm_suspend() method, that
makes sense since a suspended CPU is still online and can receive
interrupts whereas a hotplugged CPU, since it is offline,
migrated all IRQs and shutdown the per-CPU peripherals, hence
their PPIs.
The flaw with this reasoning is the following. If all CPUs in
a clusters are entering a power down state either through CPU
idle or CPU hotplug, when the last man successfully completes
the MCPM power down sequence (and executes wfi), power controller
waits for L2 wfi signal to quiesce the cluster and shut it down.
If, when all CPUs are sitting in wfi, an online CPU hotplugs back
in one of the CPUs in the cluster being shutdown, that CPU
receives an IPI that causes wfi to complete (since tc2_pm_down()
method does not disable the GIC CPU IF in that case - CPU being
hotplugged out, not idle) and the power controller will never see
the stanbywfil2 signal coming from L2 that is required for
shutdown to happen and the system deadlocks.
Further to this issue, kexec hotplugs secondary CPUs out during
kernel reload/restart.
Because kexec may (deliberately) trash the old kernel text, it is
not OK for CPUs to follow the MCPM soft reboot path, since
instructions after the WFI may have been replaced by kexec.
If tc2_pm_down() does not disable the GIC cpu interface, there is a
race between CPU powerdown in the old kernel and the IPI from the
new kernel that triggers secondary boot, particularly if the
powerdown is slow (due to L2 cache cleaning for example). If the
new kernel wins the race, the affected CPU(s) will not really be
reset and may execute garbage after the WFI.
The only solution to this problem consists in disabling the GIC
CPU IF on a CPU committed to power down regardless of the power
down entry method (CPU hotplug or CPU idle). This way, CPU wake-up
is under power controller control, which prevents unexpected wfi
exit caused by a pending IRQ.
This patch moves the GIC CPU IF disable call in the TC2 MCPM
implementation from the tc2_pm_suspend() method to the
tc2_pm_down() method to fix the mentioned race condition(s).
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com> (for kexec)
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman:
Fourth Round of Renesas ARM based SoC fixes for v3.12
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
* tag 'renesas-fixes4-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Olof Johansson <olof@lixom.net>
the current dts is lacking interrupt and dma prop for video input
processor of prima2 and atlas6, this patch fixes it.
Signed-off-by: Renwei Wu <Renwei.Wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
we lost an address range <0x56000000 0x56000000 0x1b00000> for peri-iobg
of prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently, development on arm64 is aided by a Foundation_v8 emulator
distributed by ARM [1]. To run their kernels, users will execute:
$ ./Foundation_v8 --image linux-system.axf --block-device raring-rootfs
To mount the raring-rootfs filesystem, the kernel parameter should
typically include:
root=/dev/vda
For this device to be present, the kernel must be compiled with
VIRTIO_{MMIO,BLK}. To make this work out-of-the-box, make it part of the
default configuration.
[1]: https://silver.arm.com/browse/FM00A
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It turns out the kernel relies on barrier() to force a reload of the
percpu offset value. Since we can't easily modify the definition of
barrier() to include "tp" as an output register, we instead provide a
definition of __my_cpu_offset as extended assembly that includes a fake
stack read to hazard against barrier(), forcing gcc to know that it
must reread "tp" and recompute anything based on "tp" after a barrier.
This fixes observed hangs in the slub allocator when we are looping
on a percpu cmpxchg_double.
A similar fix for ARMv7 was made in June in change 509eb76ebf.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
NETGEAR ReadyNAS 102 Power button definition in .dts file flags
associated GPIO active low instead of active high. This results
in reversed events reported by input subsystem (0 returned when
the button is pressed, 1 when released). This patch makes
associated GPIO active high to recover correct behaviour.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In the flexcan_chip_start() function first the flexcan core is going through
the soft reset sequence, then the RX FIFO is enabled.
With the hardware is put into FIFO mode, message buffers 1...7 are reserved by
the FIFO engine. The remaining message buffers are in reset default values.
This patch removes the bogus initialization of the message buffers, as it
causes an imprecise external abort on imx6.
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Git commit 616498813b "s390: system call path micro optimization"
introduced a regression in regard to system call restarting and inferior
function calls via the ptrace interface. The pointer to the system call
table needs to be loaded in sysc_sigpending if do_signal returns with
TIF_SYSCALl set after it restored a system call context.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently copy_from_oldmem() is not able to copy to virtual memory.
When using kexec pre-allocated ELF header, copy_from_oldmem()
is used to copy the ELF notes information to vmalloc buffers.
So fix this and use the new function copy_from_realmem() that allows
copying also to vmalloc memory.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To detect a line mode console we need a message event type
for the receive mask and a command event type for the send mask.
Checking for a MSG event in the sclp send mask was wrong and
might result in line mode consoles not being detected.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
"execute relative long" may have all sorts of side effects dependend on
the instructions it executes.
Therefore prohibit setting a kprobe on exrl just like we do for the
regular execute instruction.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of error, the function tty3270_alloc_screen() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
TCP packets hitting the SYN proxy through the SYNPROXY target are not
validated by TCP conntrack. When th->doff is below 5, an underflow happens
when calculating the options length, causing skb_header_pointer() to
return NULL and triggering the BUG_ON().
Handle this case gracefully by checking for NULL instead of using BUG_ON().
Reported-by: Martin Topholm <mph@one.com>
Tested-by: Martin Topholm <mph@one.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acer Aspire 3830TG seems requiring GPIO bit 0 as the primary mute
control. When a machine is booted after Windows 8, the GPIO pin is
turned off and it results in the silent output.
This patch adds the manual fixup of GPIO bit 0 for this model.
Reported-by: Christopher <DIDI2002@web.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v3.12
Nothing too exciting here, all driver specific except for the fix from
Liam for DPCM systems which have both front and back end DAIs which is
not yet used by anything in mainline.
The patch fixes the following compiler warning:
CC arch/avr32/kernel/process.o
arch/avr32/kernel/process.c: In function 'copy_thread':
arch/avr32/kernel/process.c:292: warning: assignment makes integer \
from pointer without a cast
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Since commit 01426478df
(avr32: Use generic idle loop) the kernel throws the
following warning on avr32:
WARNING: at 900322e4 [verbose debug info unavailable]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0-rc2 #117
task: 901c3ecc ti: 901c0000 task.ti: 901c0000
PC is at cpu_idle_poll_ctrl+0x1c/0x38
LR is at comparator_mode+0x3e/0x40
pc : [<900322e4>] lr : [<90014882>] Not tainted
sp : 901c1f74 r12: 00000000 r11: 901c74a0
r10: 901d2510 r9 : 00000001 r8 : 901db4de
r7 : 901c74a0 r6 : 00000001 r5 : 00410020 r4 : 901db574
r3 : 00410024 r2 : 90206fe0 r1 : 00000000 r0 : 007f0000
Flags: qvnzc
Mode bits: hjmde....G
CPU Mode: Supervisor
Call trace:
[<90039ede>] clockevents_set_mode+0x16/0x2e
[<90039f00>] clockevents_shutdown+0xa/0x1e
[<9003a078>] clockevents_exchange_device+0x58/0x70
[<9003a78c>] tick_check_new_device+0x38/0x54
[<9003a1a2>] clockevents_register_device+0x32/0x90
[<900035c4>] time_init+0xa8/0x108
[<90000520>] start_kernel+0x128/0x23c
When the 'avr32_comparator' clockevent device is registered,
the clockevent core sets the mode of that clockevent device
to CLOCK_EVT_MODE_SHUTDOWN. Due to this, the 'comparator_mode'
function calls the 'cpu_idle_poll_ctrl' to disables idle poll.
This results in the aforementioned warning because the polling
is not enabled yet.
Change the code to only disable idle poll if it is enabled by
the same function to avoid the warning.
Cc: stable@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Use kbuild to add asm-generic headers that do nothing, also remove the arch
specific wrapper headers.
This only affects headers that do nothing but include the generic
equivalent. It does not touch any header that does a little more.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Superblock lock was replaced with (un)lock_super() removal, but left
uninitialized for Seventh Edition UNIX filesystem in the following commit (3.7):
c07cb01 sysv: drop lock/unlock super
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use the shash interface, rather than the hash interface, when hashing
AppArmor profiles. The shash interface does not use scatterlists and it
is a better fit for what AppArmor needs.
This fixes a kernel paging BUG when aa_calc_profile_hash() is passed a
buffer from vmalloc(). The hash interface requires callers to handle
vmalloc() buffers differently than what AppArmor was doing. Due to
vmalloc() memory not being physically contiguous, each individual page
behind the buffer must be assigned to a scatterlist with sg_set_page()
and then the scatterlist passed to crypto_hash_update().
The shash interface does not have that limitation and allows vmalloc()
and kmalloc() buffers to be handled in the same manner.
BugLink: https://launchpad.net/bugs/1216294/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=62261
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull USB fixes from Greg KH:
"Here are a number of USB driver fixes for 3.12-rc3.
These are all for host controller issues that have been reported, and
there's a fix for an annoying error message that gets printed every
time you remove a USB 3 device from the system that's been bugging me
for a while"
* tag 'usb-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: add support for Merrifield
USB: fsl/ehci: fix failure of checking PHY_CLK_VALID during reinitialization
USB: Fix breakage in ffs_fs_mount()
fsl/usb: Resolve PHY_CLK_VLD instability issue for ULPI phy
usb/core/devio.c: Don't reject control message to endpoint with wrong direction bit
usb: chipidea: USB_CHIPIDEA should depend on HAS_DMA
usb: chipidea: udc: free pending TD at removal procedure
usb: chipidea: imx: Add usb_phy_shutdown at probe's error path
usb: chipidea: Fix memleak for ci->hw_bank.regmap when removal
usb: chipidea: udc: fix the oops after rmmod gadget
USB: fix PM config symbol in uhci-hcd, ehci-hcd, and xhci-hcd
USB: OHCI: accept very late isochronous URBs
USB: UHCI: accept very late isochronous URBs
USB: iMX21: accept very late isochronous URBs
usbcore: check usb device's state before sending a Set SEL control transfer
xhci: Fix race between ep halt and URB cancellation
usb: Fix xHCI host issues on remote wakeup.
xhci: Ensure a command structure points to the correct trb on the command ring
xhci: Fix oops happening after address device timeout
Pull tty/serial fixes from Greg KH:
"Here are some serial at tty driver fixes for 3.12-rc3
The serial driver fixes some kref leaks, documentation is moved to the
proper places, and the tty and n_tty fixes resolve some reported
regressions. There is still one outstanding tty regression fix that
isn't in here yet, as I want to test it out some more, it will be sent
for 3.12-rc4 if it checks out"
* tag 'tty-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: ar933x_uart: move devicetree binding documentation
tty: Fix SIGTTOU not sent with tcflush()
n_tty: Fix EOF push index when termios changes
serial: pch_uart: remove unnecessary tty_port_tty_get
serial: pch_uart: fix tty-kref leak in dma-rx path
serial: pch_uart: fix tty-kref leak in rx-error path
serial: tegra: fix tty-kref leak
Pull staging fixes from Greg KH:
"Here are some staging driver fixes, MAINTAINER updates, and a new
device id. All of these have been in the linux-next tree, and are
pretty simple patches"
* tag 'staging-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID
staging: imx-drm: Fix probe failure
staging: vt6656: [BUG] iwctl_siwencodeext return if device not open
staging: vt6656: [BUG] main_usb.c oops on device_close move flag earlier.
staging: vt6656: rxtx.c [BUG] s_vGetFreeContext dead lock on null apTD.
Staging: rtl8192u: r819xU_cmdpkt: checking NULL value after doing dev_alloc_skb
staging: usbip: Orphan usbip
staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
staging: r8188eu: Cocci spatch "noderef"
staging: octeon-usb: Cocci spatch "noderef"
staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
MAINTAINERS: staging: dgnc and dgap drivers: add maintainer
staging: lustre: Cocci spatch "noderef"
Pull driver core / sysfs fixes from Greg KH:
"Here are 2 fixes for 3.12-rc3. One fixes a sysfs problem with
mounting caused by 3.12-rc1, and the other is a bug reported by the
chromeos developers with the driver core.
Both have been in linux-next for a bit"
* tag 'driver-core-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core : Fix use after free of dev->parent in device_shutdown
sysfs: Allow mounting without CONFIG_NET
Pull char/misc driver fixes from Greg KH:
"Here are some HyperV and MEI driver fixes for 3.12-rc3. They resolve
some issues that people have been reporting for them"
* tag 'char-misc-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Terminate vmbus version negotiation on timeout
Drivers: hv: util: Correctly support ws2008R2 and earlier
mei: cancel stall timers in mei_reset
mei: bus: stop wait for read during cl state transition
mei: make me client counters less error prone
The previous patch introduces a compile warning by not assigning an initial
value to the "flavor" variable. This could only be a problem if the server
returns a supported secflavor list of length zero, but it's better to
fix this before it's ever hit.
Signed-off-by: Anna Schumaker <bjschuma@netapp.com>
Acked-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Call nfs4_lookup_root_sec for each flavor returned by SECINFO_NO_NAME until
one works.
One example of a situation this fixes:
- server configured for krb5
- server principal somehow gets deleted from KDC
- server still thinking krb is good, sends krb5 as first entry in
SECINFO_NO_NAME response
- client tries krb5, but this fails without even sending an RPC because
gssd's requests to the KDC can't find the server's principal
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We need to ensure that the initialisation of the data server nfs_client
structure in nfs4_ds_connect is correctly ordered w.r.t. the read of
ds->ds_clp in nfs4_fl_prepare_ds.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull drm fixes from Dave Airlie:
"Nothing too major, radeon still has some dpm changes for off by
default.
Radeon, intel, msm:
- radeon: a few more dpm fixes (still off by default), uvd fixes
- i915: runtime warn backtrace and regression fix
- msm: iommu changes fallout"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (27 commits)
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
drm/i915: Fix up usage of SHRINK_STOP
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/i915: preserve pipe A quirk in i9xx_set_pipeconf
drm/i915/tv: clear adjusted_mode.flags
drm/i915/dp: increase i2c-over-aux retry interval on AUX DEFER
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/i915: Use a temporary va_list for two-pass string handling
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
...
This reverts commit de95ab5364.
Markus Trippelsdorf reported that this commit broke 'perf top':
> I just see a gray screen with no text at all. Sometimes the
> following error messages are printed:
>
> *** Error in `perf': invalid fastbin entry (free): 0x00000000029b18c0
> ***
> *** Error in `perf': malloc(): memory corruption (fast): 0x0000000000ee0b10 ***
While this code is fixable, the commit itself fails on several levels:
- it should have been a separate helper function
- why the heck does it do strchr() twice
- it casts a const char * over into char *
- sloppy style
- it's not even a regression fix!
So lets revert it and re-try the patch in v3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A small fix + deal with fallout of iommu changes + use new
drm_gem_dumb_destroy helper.
* 'msm-fixes-3.12-rc2' of git://people.freedesktop.org/~robclark/linux:
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
A host might need net_secret[] and never open a single socket.
Problem added in commit aebda156a5
("net: defer net_secret[] initialization")
Based on prior patch from Hannes Frederic Sowa.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@strressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently serialization network namespaces exiting and
network devices exiting as the final part of netdev_run_todo does not
happen under the rtnl_lock. This is compounded by the fact that the
only list of devices unregistering in netdev_run_todo is local to the
netdev_run_todo.
This lack of serialization in extreme cases results in network devices
unregistering in netdev_run_todo after the loopback device of their
network namespace has been freed (making dst_ifdown unsafe), and after
the their network namespace has exited (making the NETDEV_UNREGISTER,
and NETDEV_UNREGISTER_FINAL callbacks unsafe).
Add the missing serialization by a per network namespace count of how
many network devices are unregistering and having a wait queue that is
woken up whenever the count is decreased. The count and wait queue
allow default_device_exit_batch to wait until all of the unregistration
activity for a network namespace has finished before proceeding to
unregister the loopback device and then allowing the network namespace
to exit.
Only a single global wait queue is used because there is a single global
lock, and there is a single waiter, per network namespace wait queues
would be a waste of resources.
The per network namespace count of unregistering devices gives a
progress guarantee because the number of network devices unregistering
in an exiting network namespace must ultimately drop to zero (assuming
network device unregistration completes).
The basic logic remains the same as in v1. This patch is now half
comment and half rtnl_lock_unregistering an expanded version of
wait_event performs no extra work in the common case where no network
devices are unregistering when we get to default_device_exit_batch.
Reported-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler, timer and x86 fixes from Ingo Molnar:
- A context tracking ARM build and functional fix
- A handful of ARM clocksource/clockevent driver fixes
- An AMD microcode patch level sysfs reporting fixlet
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm: Fix build error with context tracking calls
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
clocksource: of: Respect device tree node status
clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
arm: clocksource: mvebu: Use the main timer as clock source from DT
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix patch level reporting for family 15h
Pull perf fixes from Ingo Molnar:
"A couple of tooling fixlets and a PMU detection printout fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix PMU detection printout when no PMU is detected
perf symbols: Demangle cloned functions
perf machine: Fix path unpopulated in machine__create_modules()
perf tools: Explicitly add libdl dependency
perf probe: Fix probing symbols with optimization suffix
perf trace: Add mmap2 handler
perf kmem: Make it work again on non NUMA machines
Pull xfs bugfixes from Ben Myers:
- fix for directory node collapse regression
- fix for recovery over stale on disk structures
- fix for eofblocks ioctl
- fix asserts in xfs_inode_free
- lock the ail before removing an item from it
* tag 'xfs-for-linus-v3.12-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: fix node forward in xfs_node_toosmall
xfs: log recovery lsn ordering needs uuid check
xfs: fix XFS_IOC_FREE_EOFBLOCKS definition
xfs: asserting lock not held during freeing not valid
xfs: lock the AIL before removing the buffer item
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ismt: initialize DMA buffer
i2c: designware: 10-bit addressing mode enabling if I2C_DYNAMIC_TAR_UPDATE is set
i2c: mv64xxx: Do not use writel_relaxed()
i2c: mv64xxx: Fix some build warnings
i2c: s3c2410: fix clk_disable/clk_unprepare WARNings
Pull ACPI and power management fixes from Rafael Wysocki:
"These fix one recent cpufreq regression, a few older bugs that may
harm users and a kerneldoc typo.
Specifics:
1) After the recent locking changes in the cpufreq core it is
possible to trigger BUG_ON(!policy) in lock_policy_rwsem_read() if
cpufreq_get() is called before registering a cpufreq driver. Fix
from Viresh Kumar.
2) If intel_pstate has been loaded already, it doesn't make sense to
do anything in acpi_cpufreq_init() and moreover doing something in
there in that case may be harmful, so make that function return
immediately if another cpufreq driver is already present. From
Yinghai Lu.
3) The ACPI IPMI driver sometimes attempts to acquire a mutex from
interrupt context, which can be avoided by replacing that mutex
with a spinlock. From Lv Zheng.
4) A NULL pointer may be dereferenced by the exynos5440 cpufreq
driver if a memory allocation made by it fails. Fix from Sachin
Kamat.
5) Hanjun Guo's commit fixes a typo in the kerneldoc comment
documenting acpi_bus_unregister_driver()"
* tag 'pm+acpi-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: fix typo in comments of acpi_bus_unregister_driver()
cpufreq: exynos5440: Fix potential NULL pointer dereference
cpufreq: check cpufreq driver is valid and cpufreq isn't disabled in cpufreq_get()
acpi-cpufreq: skip loading acpi_cpufreq after intel_pstate
ACPI / IPMI: Fix atomic context requirement of ipmi_msg_handler()
Ben Herrenschmidt found that commit 928bea9648 ("PCI: Delay enabling
bridges until they're needed") breaks PCI in some powerpc environments.
The reason is that the PCIe port driver will call pci_enable_device() on
the bridge, so the device is enabled, but skips pci_set_master because
pcie_port_auto and no acpi on powerpc.
Because of that, pci_enable_bridge() later on (called as a result of the
child device driver doing pci_enable_device) will see the bridge as
already enabled and will not call pci_set_master() on it.
Fixed by add checking in pci_enable_bridge, and call pci_set_master
if driver skip that.
That will make the code more robot and wade off problem for missing
pci_set_master in drivers.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a router is doing DNAT for 6to4/6rd packets the latest
anti-spoofing commit 218774dc ("ipv6: add anti-spoofing checks for
6to4 and 6rd") will drop them because the IPv6 address embedded does
not match the IPv4 destination. This patch will allow them to pass by
testing if we have an address that matches on 6to4/6rd interface. I
have been hit by this problem using Fedora and IPV6TO4_IPV4ADDR.
Also, log the dropped packets (with rate limit).
Signed-off-by: Catalin(ux) M. BOIE <catab@embedromix.ro>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 638c5115a7949(USBNET: support DMA SG) introduces DMA SG
if the usb host controller is capable of building packet from
discontinuous buffers, but missed handling padding packet when
building DMA SG.
This patch attachs the pre-allocated padding packet at the
end of the sg list, so padding packet can be sent to device
if drivers require that.
Reported-by: David Laight <David.Laight@aculab.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 lockref enablement from Heiko Carstens:
"Enabling the new lockless lockref variant on s390 would have been
trivial until Tony Luck added a cpu_relax() call into the
CMPXCHG_LOOP(), with commit d472d9d98b ("lockref: Relax in cmpxchg
loop")
As already mentioned cpu_relax() is very expensive on s390 since it
yields() the current virtual cpu. So we are talking of several
thousand cycles. Considering this enabling the lockless lockref
variant would contradict the intention of the new semantics. And also
some quick measurements show performance regressions of 50% and more.
Simply removing the cpu_relax() call again seems also not very
desireable since Waiman Long reported that for some workloads the call
improved performance by 5%."
* 'lockref' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: enable ARCH_USE_CMPXCHG_LOCKREF
lockref: use arch_mutex_cpu_relax() in CMPXCHG_LOOP()
mutex: replace CONFIG_HAVE_ARCH_MUTEX_CPU_RELAX with simple ifdef
Pull DeviceTree fixes from Rob Herring:
"Clean-up to fix some warnings for !OF builds and spelling fixes in
docs:
- Clean-up openrisc prom.h
- Fix warnings caused by of_irq.h ifdefs
- Spelling fix for Synopsys"
* tag 'devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dts: Fix misspelling of Synopsys
of: clean-up ifdefs in of_irq.h
openrisc: clean-up prom.h
Pull ARM fixes from Russell King:
"Just a few relatively small ARM fixes found since the last merge
window, nothing too exciting"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7837/3: fix Thumb-2 bug in AES assembler code
ARM: only allow kernel mode neon with AEABI
ARM: 7839/1: entry: fix tracing of ARM-private syscalls
ARM: 7836/1: add __get_user_unaligned/__put_user_unaligned
This patch adds code to initialize the DMA buffer to compensate for
possible hardware data corruption.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
[wsa: changed to use 'sizeof']
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We still need an API exported by msm iommu driver (but not visible in
any public header anymore). For now, just declare the prototype
ourselves, but when msm iommu driver provides a better option, use that
instead.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Ran into this cryptic PMU bootup log recently:
[ 0.124047] Performance Events:
[ 0.125000] smpboot: ...
Turns out we print this if no PMU is detected. Fall back to
the right condition so that the following is printed:
[ 0.122381] Performance Events: no PMU driver, software events only.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: http://lkml.kernel.org/n/tip-u2fwaUffakjp0qkpRfqljgsn@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The include file has been removed and the file does not
need it anyway, so remove it. Fixes a compile error.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The variable priv->kms is not initialized yet.
Found by "scripts/coccinelle/tests/odd_ptr_err.cocci".
PTR_ERR should access the value just tested by IS_ERR.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Since devm_regulator_get is used, regulator_put should not be
used. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable ARCH_USE_CMPXCHG_LOCKREF since it shows performance improvements
with Linus' simple stat() test case of up to 50% on a 30 cpu system.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Make use of arch_mutex_cpu_relax() so architectures can override the
default cpu_relax() semantics.
This is especially useful for s390, where cpu_relax() means that we
yield() the current (virtual) cpu and therefore is very expensive,
and would contradict the whole purpose of the lockless cmpxchg loop.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Linus suggested to replace
#ifndef CONFIG_HAVE_ARCH_MUTEX_CPU_RELAX
#define arch_mutex_cpu_relax() cpu_relax()
#endif
with just a simple
#ifndef arch_mutex_cpu_relax
# define arch_mutex_cpu_relax() cpu_relax()
#endif
to get rid of CONFIG_HAVE_CPU_RELAX_SIMPLE. So architectures can
simply define arch_mutex_cpu_relax if they want an architecture
specific function instead of having to add a select statement in
their Kconfig in addition.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
More radeon fixes for 3.12. Kind of all over the place: UVD, DPM,
tiling, etc.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
drm/radeon: fix missed variable sized access
drm/radeon: Make r100_cp_ring_info() and radeon_ring_gfx() safe (v2)
drm/radeon/cik: Add tiling mode index for 1D tiled depth/stencil surfaces
drm/radeon/cik: Fix encoding of number of banks in tiling configuration info
drm/radeon/cik: Fix printing of client name on VM protection fault
drm/radeon: additional gcc fixes for radeon_atombios.c
drm/radeon: avoid UVD corruption on AGP cards using GPU gart
Just a few fixes for regressions and other serious stuff.
Two fix state tracking mismatches, together with an additional patch that
I've submitted to stable (somehow forgotten to tag it) we should have them
fixed now (I hope).
* tag 'drm-intel-fixes-2013-09-26' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix up usage of SHRINK_STOP
drm/i915: preserve pipe A quirk in i9xx_set_pipeconf
drm/i915/tv: clear adjusted_mode.flags
drm/i915/dp: increase i2c-over-aux retry interval on AUX DEFER
drm/i915: Use a temporary va_list for two-pass string handling
VLAN priority is not being displayed for a VF currently when user executes
"ip link show" command. This patch fixes it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thix fix allows the VLAN priority to be configured for a VF interface
via the "ip link set DEVICE vf NUM" path.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the VF interfaces have privilege to add VLANs.
Allow VLANs to be configured on these interfaces.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In BE3-R, when UMC is enabled, the number of VLANs that can be added
to the interface is reduced to 15.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 117a0c5fc9 ("sparc: kernel: using
strlcpy() instead of strcpy()") added a bug to ldom_reboot in
arch/sparc/kernel/ds.c
- strcpy(full_boot_str + strlen("boot "), boot_command);
+ strlcpy(full_boot_str + strlen("boot "), boot_command,
+ sizeof(full_boot_str + strlen("boot ")));
That last sizeof() expression evaluates to sizeof(size_t) which is
not what was intended.
Also even the corrected:
sizeof(full_boot_str) + strlen("boot ")
is not right as the destination buffer length is just plain
"sizeof(full_boot_str)" and that's what the final argument
should be.
Signed-off-by: David S. Miller <davem@davemloft.net>
When coming from a page fault (for example), interrupts might
be enabled as we enter the code to return from interrupt.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
hardwall used __SPIN_LOCK_INITIALIZER directly instead of the preferred
__SPIN_LOCK_UNLOCKED. This also has the benefit that it will compile
when applying the preempt-rt patch series.
Signed-off-by: Henrik Austad <haustad@cisco.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
atomic* value is signed value, and atomic* functions need also process
signed value (parameter value, and return value), so use 'long long'
instead of 'u64'.
After replacement, it will also fix a bug for atomic64_add_negative():
"u64 is never less than 0".
The modifications are:
in vim, use "1,% s/\<u64\>/long long/g" command.
remove redundant '__aligned(8)'.
be sure of 80 (and macro '\') columns limitation after replacement.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [re-instated const cast]
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"First Bluetooth fixes to 3.12, it includes:
* 3 patches to add device id for 3 new hardwares.
* 2 patches from Johan to fix the rfkill behaviour during setup stage
* a small clean up in the rfcomm TTY code that fixes a potential racy
condition (by Gianluca Anzolin)
* 2 fixes to proper set encryption key size and security level in the
peripheral role of Bluetooth LE devices. (by Andre Guedes)
* a fix for dealing devices where pairing is not necessary, we were keeping
the Bluetooth ACL connection alive for too much time. (by Syam Sidhardhan)"
Also, I fixed-up an curly-brace indentation problem in the Bluetooth
code while merging. On top of that...
Alexey Khoroshilov brings a p54usb fix to avoid a resource leak when
request_firmware_nowait fails.
Amitkumar Karwar fixes a firmware hang caused by too much header data
being appended for USB devices using the mwifiex driver.
Arend van Spriel provides three fixes: a brcmfmac fix to relocate some
driver code outside of an .init section; a scheduling while atomic
fix for bcma; and, another scheduling while atomic fix for brcmsmac.
Bing Zhao offers a pair of mwifiex fixes: a code change to avoid
firmware timeouts on USB; and a fix for a NULL pointer dereference.
Christian Lamparter adds a device ID to p54usb.
Felix Fietkau implements a quartet of small ath9k fixes, including
a locking fix, a list management fix, a fix to properly mark a stale
buffer, and an aggregate buffering fix.
Larry Finger champions a data alignment fix to make rtlwifi work
better with ARM builds.
Solomon Peachy reverts an earlier interrupt handling fix for cw1200
and replaces it with a new threaded oneshot irq handler implementation.
Sujith Manoharan fixes an ath9k regression by reverting an earlier
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb and i40e.
Todd provides a fix for 82580 devices in igb, where the ethtool
loopback test was missing 82580 copper devices.
Jesse provides five fixes/cleanups to i40e based on feedback from
Joe Perches and the community.
v2: fixed up patch 5 in the series based on feedback from Joe Perches
and David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If context switching happens during executing fpsimd_flush_thread(),
stale value in FPSIMD registers will be saved into current thread's
fpsimd_state by fpsimd_thread_switch(). That may cause invalid
initialization state for the new process, so disable preemption
when executing fpsimd_flush_thread().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull hwmon fix from Guenter Roeck:
"Fix potential crash condition in applesmc driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (applesmc) Check key count before proceeding
Pull sound fixes from Takashi Iwai:
"Nothing too serious here: a couple of compress-offload core fixes,
Haswell HDMI audio fix, a fixup for new MacBook Airs and a few COEF
setups for ALC283 mic problems"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Enable internal mic on a Thinkpad machine with ALC283
ALSA: hda - Fix Internal Mic boost can't control with ALC283
ALSA: hda - Add documentation for CS4208 fixups
ALSA: hda - Add fixup for MacBook Air 6,1 and 6,2 with CS4208 codec
ALSA : hda - not use assigned converters for all unused pins
ALSA: compress: Make sure we trigger STOP before closing the stream.
ALSA: compress: Fix compress device unregister.
Pull fbdev fixes from Tomi Valkeinen:
"Small fbdev fixes for various fb drivers"
* tag 'fbdev-fixes-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: mxsfb: Add missing break
video: of: display_timing: correct display-timings node finding
neofb: fix error return code in neofb_probe()
s3fb: fix error return code in s3_pci_probe()
video: mmp: drop needless devm cleanup
OMAPDSS: Add missing dependency on backlight for DSI-CM panel drier
OMAPDSS: DISPC: set irq_safe for runtime PM
OMAPDSS: Return right error during connector probe
Pull reiserfs and UDF fixes from Jan Kara:
"The contains fix of an UDF oops when mounting corrupted media and a
fix of a race in reiserfs leading to oops"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: fix race with flush_used_journal_lists and flush_journal_list
reiserfs: remove useless flush_old_journal_lists
udf: Fortify LVID loading
In kobj_ns_current_may_mount the default should be to allow the mount.
The test is only for a single kobj_ns_type at a time, and unless there
is a reason to prevent it the mounting sysfs should be allowed.
Subsystems that are not registered can't have are not involved so can't
have a reason to prevent mounting sysfs.
This is a bug-fix to commit 7dc5dbc879 ("sysfs: Restrict mounting
sysfs") that came in via the userns tree during the 3.12 merge window.
Reported-and-tested-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 64-bit cmpxchg operation on the lockref is ordered by virtue of
hazarding between the cmpxchg operation and the reference count
manipulation. On weakly ordered memory architectures (such as ARM), it
can be of great benefit to omit the barrier instructions where they are
not needed.
This patch moves the lockless lockref code over to a cmpxchg64_relaxed
operation, which doesn't provide barrier semantics. If the operation
isn't defined, we simply #define it as the usual 64-bit cmpxchg macro.
Cc: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver is used on PowerPC which don't provide writel_relaxed(). This
breaks the c2k and prpmc2800 default configurations. To fix the build,
turn the calls to writel_relaxed() into writel(). The impacts for ARM
should be minimal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some functions and variables are only used if the configuration selects
HAVE_CLK. Protect them with a corresponding #ifdef CONFIG_HAVE_CLK block
to avoid compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[wsa: added marker to #endif]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit d16933b339 "i2c: s3c2410: Move
location of clk_prepare_enable() call in probe function" refactored
clk_enable and clk_disable calls yet neglected to remove the
clk_disable_unprepare call in the module's remove().
It helps remove warnings on an arndale during unbind:
echo 12c90000.i2c > /sys/bus/platform/devices/12c90000.i2c/driver/unbind
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:842 clk_disable+0x18/0x24()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Not tainted 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c4a64>] (clk_disable+0x18/0x24)
[<c02c4a64>] (clk_disable+0x18/0x24) from [<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70)
[<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a6 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:751 clk_unprepare+0x14/0x1c()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Tainted: G W 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c5834>] (clk_unprepare+0x14/0x1c)
[<c02c5834>] (clk_unprepare+0x14/0x1c) from [<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70)
[<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a7 ]---
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Recent movement of all configurations of pin in the single call of
pin_config_set(), it is aborting configuration if BIAS_PULL_PIN_DEFAULT
is selected as return of configuration.
The original idea was to just avoid any update on register for pull up/down
configuration if this option is selected.
Fixing this by just bypassing any register update for BIAS_PULL_PIN_DEFAULT
and continuing the remaining configuration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As documented in Application Note SWPA117 v2.1(NDA), LDO override has a
requirement that when switching from Bias active + override active
mode(FBB/RBB) to Bypass(nominal) mode, LDO reset must be performed
*after* LDO transitions to Bypass(nominal) mode.
The same rule in reverse applies when switching from a ABB bypass mode
to ABB enabled - LDO override *must* be performed prior to transition to
required ABB mode, if we do not do that, the same glitch takes place.
Currently while transitioning to ABB bypass, we reset the LDO overide
prior to the transition which causes a few milliseconds where ABB LDO
voltage could go all the way to 800mV(based on SoC process node),
during this period, the delta voltage between VDD rail and VBB rail
could cause the system to improperly function.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Otherwise we may try to start transfers immediately and then fail to
runtime resume the device causing us not to have clocks enabled.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Conflicts:
drivers/spi/spi-s3c64xx.c
coccicheck shows:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment
Fix each of them with a *a = *b;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.
A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.
v2: fix post increment bug in return
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ALC283 pin control for Line1 default control by hidden register.
Use line1 as internal Mic will not get sound when boost value up.
Set control by verb for hidden register will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.
This allows for clean up of the return types that were previously
converted to int.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
clockevents_config_and_register is more clever and correct than doing it
by hand; so use it.
[vgupta: fixed build failure due to missing ; in patch]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Some ARC SMP systems lack native atomic R-M-W (LLOCK/SCOND) insns and
can only use atomic EX insn (reg with mem) to build higher level R-M-W
primitives. This includes a SystemC based SMP simulation model.
So rwlocks need to use a protecting spinlock for atomic cmp-n-exchange
operation to update reader(s)/writer count.
The spinlock operation itself looks as follows:
mov reg, 1 ; 1=locked, 0=unlocked
retry:
EX reg, [lock] ; load existing, store 1, atomically
BREQ reg, 1, rety ; if already locked, retry
In single-threaded simulation, SystemC alternates between the 2 cores
with "N" insn each based scheduling. Additionally for insn with global
side effect, such as EX writing to shared mem, a core switch is
enforced too.
Given that, 2 cores doing a repeated EX on same location, Linux often
got into a livelock e.g. when both cores were fiddling with tasklist
lock (gdbserver / hackbench) for read/write respectively as the
sequence diagram below shows:
core1 core2
-------- --------
1. spin lock [EX r=0, w=1] - LOCKED
2. rwlock(Read) - LOCKED
3. spin unlock [ST 0] - UNLOCKED
spin lock [EX r=0,w=1] - LOCKED
-- resched core 1----
5. spin lock [EX r=1] - ALREADY-LOCKED
-- resched core 2----
6. rwlock(Write) - READER-LOCKED
7. spin unlock [ST 0]
8. rwlock failed, retry again
9. spin lock [EX r=0, w=1]
-- resched core 1----
10 spinlock locked in #9, retry #5
11. spin lock [EX gets 1]
-- resched core 2----
...
...
The fix was to unlock using the EX insn too (step 7), to trigger another
SystemC scheduling pass which would let core1 proceed, eliding the
livelock.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Anton reported
| LTP tests syscalls/process_vm_readv01 and process_vm_writev01 fail
| similarly in one testcase test_iov_invalid -> lvec->iov_base.
| Testcase expects errno EFAULT and return code -1,
| but it gets return code 1 and ERRNO is 0 what means success.
Essentially test case was passing a pointer of -1 which access_ok()
was not catching. It was doing [@addr + @sz <= TASK_SIZE] which would
pass for @addr == -1
Fixed that by rewriting as [@addr <= TASK_SIZE - @sz]
Reported-by: Anton Kolesov <Anton.Kolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
If a load or store is the last instruction in a zero-overhead-loop, and
it's misaligned, the loop would execute only once.
This fixes that problem.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
According to the datasheet for Micron n25q256a (N25Q256A13ESF40F) 4-byte
addressing mode should be entered as follows:
<quote>
To enter or exit the 4-byte address mode, the WRITE ENABLE command
must be executed to set the write enable latch bit to 1. (Note: The
WRITE ENABLE command must NOT be executed on the N25Q256A83ESF40x and
N25Q256A83E1240x devices.) S# must be driven LOW. The effect of the
command is immediate; after the command has been executed, the write
enable latch bit is cleared to 0.
</quote>
Micron's portable way to perform this for all types of Micron flash
is to first issue a write enable, then switch the addressing mode
followed by a write disable to avoid leaving the flash in a write-
able state.
Signed-off-by: Elie De Brauwer <eliedebrauwer@email.com>
[Brian: reworked a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes a memory leak in the ONFI support code for detecting the
required ECC levels from this commit:
commit 6dcbe0cdd8
Author: Huang Shijie <b32955@freescale.com>
Date: Wed May 22 10:28:27 2013 +0800
mtd: get the ECC info from the Extended Parameter Page
In the success case, we never freed the 'ep' buffer.
Also, this fixes an oversight in the same commit where we (harmlessly)
freed the NULL pointer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
devm_clk_get() is used so there is no reason to explicitly
call clk_put() in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the default pin configuration and some init verbs for
setting COEFs, in addition to the correction of input pin AMP caps
for MacBook Air 6,1 and 6,2. With these changes, the headphone jack
detection starts working properly.
[trivial space fixes by tiwai]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Signed-off-by: Ben Whitten <benwhitten@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On AMD family 14h, applying microcode patch on the a core (core0)
would also affect the other core (core1) in the same compute
unit. The driver would skip applying the patch on core1, but it
still need to update kernel structures to reflect the proper
patch level.
The current logic is not updating the struct
ucode_cpu_info.cpu_sig.rev of the skipped core. This causes the
/sys/devices/system/cpu/cpu1/microcode/version to report
incorrect patch level as shown below:
$ grep . cpu?/microcode/version
cpu0/microcode/version:0x600063d
cpu1/microcode/version:0x6000626
cpu2/microcode/version:0x600063d
cpu3/microcode/version:0x6000626
cpu4/microcode/version:0x600063d
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: <bp@alien8.de>
Cc: <jacob.w.shin@gmail.com>
Cc: <herrmann.der.user@googlemail.com>
Link: http://lkml.kernel.org/r/1285806432-1995-1-git-send-email-suravee.suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dmitry Vyukov managed to trigger a case where aio_migratepage can cause a
use-after-free during teardown of the aio ring buffer's mapping. This turns
out to be caused by access to the ioctx's ring_pages via the migratepage
operation which was not being protected by any locks during ioctx freeing.
Use the address_space's private_lock to protect use and updates of the mapping's
private_data, and make ioctx teardown unlink the ioctx from the address space.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bunch of failure exits in ffs_fs_mount() with
seriously broken recovery logics. Most of that appears to stem
from misunderstanding of the ->kill_sb() semantics; unlike
->put_super() it is called for *all* superblocks of given type,
no matter how (in)complete the setup had been. ->put_super()
is called only if ->s_root is not NULL; any failure prior to
setting ->s_root will have the call of ->put_super() skipped.
->kill_sb(), OTOH, awaits every superblock that has come from
sget().
Current behaviour of ffs_fs_mount():
We have struct ffs_sb_fill_data data on stack there. We do
ffs_dev = functionfs_acquire_dev_callback(dev_name);
and store that in data.private_data. Then we call mount_nodev(),
passing it ffs_sb_fill() as a callback. That will either fail
outright, or manage to call ffs_sb_fill(). There we allocate an
instance of struct ffs_data, slap the value of ffs_dev (picked
from data.private_data) into ffs->private_data and overwrite
data.private_data by storing ffs into an overlapping member
(data.ffs_data). Then we store ffs into sb->s_fs_info and attempt
to set the rest of the things up (root inode, root dentry, then
create /ep0 there). Any of those might fail. Should that
happen, we get ffs_fs_kill_sb() called before mount_nodev()
returns. If mount_nodev() fails for any reason whatsoever,
we proceed to
functionfs_release_dev_callback(data.ffs_data);
That's broken in a lot of ways. Suppose the thing has failed in
allocation of e.g. root inode or dentry. We have
functionfs_release_dev_callback(ffs);
ffs_data_put(ffs);
done by ffs_fs_kill_sb() (ffs accessed via sb->s_fs_info), followed by
functionfs_release_dev_callback(ffs);
from ffs_fs_mount() (via data.ffs_data). Note that the second
functionfs_release_dev_callback() has every chance to be done to freed memory.
Suppose we fail *before* root inode allocation. What happens then?
ffs_fs_kill_sb() doesn't do anything to ffs (it's either not called at all,
or it doesn't have a pointer to ffs stored in sb->s_fs_info). And
functionfs_release_dev_callback(data.ffs_data);
is called by ffs_fs_mount(), but here we are in nasal daemon country - we
are reading from a member of union we'd never stored into. In practice,
we'll get what we used to store into the overlapping field, i.e. ffs_dev.
And then we get screwed, since we treat it (struct gfs_ffs_obj * in
disguise, returned by functionfs_acquire_dev_callback()) as struct
ffs_data *, pick what would've been ffs_data ->private_data from it
(*well* past the actual end of the struct gfs_ffs_obj - struct ffs_data
is much bigger) and poke in whatever it points to.
FWIW, there's a minor leak on top of all that in case if ffs_sb_fill()
fails on kstrdup() - ffs is obviously forgotten.
The thing is, there is no point in playing all those games with union.
Just allocate and initialize ffs_data *before* calling mount_nodev() and
pass a pointer to it via data.ffs_data. And once it's stored in
sb->s_fs_info, clear data.ffs_data, so that ffs_fs_mount() knows that
it doesn't need to kill the sucker manually - from that point on
we'll have it done by ->kill_sb().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: stable <stable@vger.kernel.org> # 3.3+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put_device(dev) at the bottom of the loop of device_shutdown
may result in the dev being cleaned up. In device_create_release,
the dev is kfreed.
However, device_shutdown attempts to use the dev pointer again after
put_device by referring to dev->parent.
Copy the parent pointer instead to avoid this condition.
This bug was found on Chromium OS's chromeos-3.8, which is based on v3.8.11.
See bug report : https://code.google.com/p/chromium/issues/detail?id=297842
This can easily be reproduced when shutting down with
hidraw devices that report battery condition.
Two examples are the HP Bluetooth Mouse X4000b and the Apple Magic Mouse.
For example, with the magic mouse :
The dev in question is "hidraw0"
dev->parent is "magicmouse"
In the course of the shutdown for this device, the input event cleanup calls
a put on hidraw0, decrementing its reference count.
When we finally get to put_device(dev) in device_shutdown, kobject_cleanup
is called and device_create_release does kfree(dev).
dev->parent is no longer valid, and we may crash in
put_device(dev->parent).
This change should be applied on any kernel with this change :
d1c6c030fc
Cc: stable@vger.kernel.org
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In kobj_ns_current_may_mount the default should be to allow the
mount. The test is only for a single kobj_ns_type at a time, and unless
there is a reason to prevent it the mounting sysfs should be allowed.
Subsystems that are not registered can't have are not involved so can't
have a reason to prevent mounting sysfs.
This is a bug-fix to:
commit 7dc5dbc879
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Mon Mar 25 20:07:01 2013 -0700
sysfs: Restrict mounting sysfs
Don't allow mounting sysfs unless the caller has CAP_SYS_ADMIN rights
over the net namespace. The principle here is if you create or have
capabilities over it you can mount it, otherwise you get to live with
what other people have mounted.
Instead of testing this with a straight forward ns_capable call,
perform this check the long and torturous way with kobject helpers,
this keeps direct knowledge of namespaces out of sysfs, and preserves
the existing sysfs abstractions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
That came in via the userns tree during the 3.12 merge window.
Reported-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 666b9adc80 terminated vmbus
version negotiation incorrectly. We need to terminate the version
negotiation only if the current negotiation were to timeout.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <ohering@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not correctly negotiate the version numbers for the util
driver when hosted on earlier hosts. The version numbers presented by this
driver were not compatible with the version numbers supported by Windows Server
2008. Fix this problem.
I would like to thank Olaf Hering (ohering@suse.com) for identifying the problem.
Reported-by: Olaf Hering <ohering@suse.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bus layer omitted check for client state transition while waiting
for read completion
The client state transition may occur for example as result
of firmware initiated reset
Add mei_cl_is_transitioning wrapper to reduce the code
repetition.:
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. u8 counters are prone to hard to detect overflow:
make them unsigned long to match bit_ functions argument type
2. don't check me_clients_num for negativity, it is unsigned.
3. init all the me client counters from one place
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).
Peter Boström noticed and reported the bug.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 'tty: ar933x_uart: add device tree support
and binding documentation' introduced a new doc in
bindins/tty/serial.
According to a recent thread [1] on the linux-serial
list, the binding documentation of serial drivers
should be added into bindings/serial.
Move the documentation of qca,ar9330-uart to the
correct place.
1. http://marc.info/?l=linux-serial&m=137771295411517
Cc: devicetree@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For controller versions greater than 1.6, setting ULPI_PHY_CLK_SEL
bit when USB_EN bit is already set causes instability issues with
PHY_CLK_VLD bit. So USB_EN is set only for IP controller version
below 1.6 before setting ULPI_PHY_CLK_SEL bit
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses platform_driver_probe() to obtain platform data
if any. However, that function is placed in the .init section so
it must be called upon driver module initialization.
The problem was reported by Fenguang Wu resulting in a kernel
oops because the .init section was already freed.
[ 48.966342] Switched to clocksource tsc
[ 48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[ 48.970851] BUG: unable to handle kernel paging request at ffffffff82196446
[ 48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163
[ 48.970957] Oops: 0011 [#1]
[ 48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23
[ 48.970957] Workqueue: events brcmf_driver_init
[ 48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000
[ 48.970957] RIP: 0010:[<ffffffff82196446>] [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP: 0000:ffff8800001d5d40 EFLAGS: 00000286
[ 48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000
[ 48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0
[ 48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002
[ 48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0
[ 48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300
[ 48.970957] FS: 0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000
[ 48.970957] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0
[ 48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[ 48.970957] Stack:
[ 48.970957] ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9
[ 48.970957] ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8
[ 48.970957] 0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000
[ 48.970957] Call Trace:
[ 48.970957] [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70
[ 48.970957] [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10
[ 48.970957] [<ffffffff81073dc5>] process_one_work+0x1d5/0x480
[ 48.970957] [<ffffffff81073d68>] ? process_one_work+0x178/0x480
[ 48.970957] [<ffffffff81074188>] worker_thread+0x118/0x3a0
[ 48.970957] [<ffffffff81074070>] ? process_one_work+0x480/0x480
[ 48.970957] [<ffffffff8107aa17>] kthread+0xe7/0xf0
[ 48.970957] [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
[ 48.970957] RIP [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP <ffff8800001d5d40>
[ 48.970957] CR2: ffffffff82196446
[ 48.970957] ---[ end trace 62980817cd525f14 ]---
Cc: <stable@vger.kernel.org> # 3.10.x, 3.11.x
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
[ 2.883807] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000048
[ 2.883813] IP: [<ffffffff815a65e0>] pfifo_fast_enqueue+0x90/0x90
[ 2.883834] CPU: 1 PID: 3220 Comm: kworker/u8:90 Not tainted
3.11.1-monotone-l0 #6
[ 2.883834] Hardware name: Microsoft Corporation Surface with
Windows 8 Pro/Surface with Windows 8 Pro,
BIOS 1.03.0450 03/29/2013
On Surface Pro, suspend to ram gives a NULL pointer dereference in
pfifo_fast_enqueue(). The stack trace reveals that the offending
call is clearing carrier in mwifiex_usb suspend handler.
Since commit 1499d9f "mwifiex: don't drop carrier flag over suspend"
has removed the carrier flag handling over suspend/resume in SDIO
and PCIe drivers, I'm removing it in USB driver too. This also fixes
the bug for Surface Pro.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
We have 4 bytes of interface header for packets delivered to SDIO
and PCIe, but not for USB interface.
In Tx AMSDU case, currently 4 bytes of garbage data is unnecessarily
appended for USB packets. This sometimes leads to a firmware hang,
because it may not interpret the data packet correctly.
Problem is fixed by removing this redundant headroom for USB.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This supercedes the older patch ("cw1200: Don't perform SPI transfers in
interrupt context") that badly attempted to fix this problem.
This is a far simpler solution, which has the added benefit of
actually working.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit aec8e88c94.
This solution turned out to cause interrupt delivery problems, and
rather than trying to fix this approach, it has been scrapped in favor
of an alternative (and far simpler) implementation.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For pcie8897, the hs_cfg cancel command (0xe5) times out when host
comes out of suspend. This is caused by an incompleted host sleep
handshake between driver and firmware.
Like SDIO interface, PCIe also needs to go through firmware power
save events to complete the handshake for host sleep configuration.
Only USB interface doesn't require power save events for hs_cfg.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.
Reported-by: Jason Andrews <jasona@cadence.com>
Tested-by: Jason Andrews <jasona@cadence.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevents race conditions when un-aggregated frames are pending in the
driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If request_firmware_nowait() fails in p54u_load_firmware(),
p54u_load_firmware_cb is not called and no one decrements usb_dev refcnt.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When .release_buffered_frames was implemented, only A-MPDU packets were
buffered internally. Now that this has changed, the BUF_AMPDU flag needs
to be checked before calling ath_tx_addto_baw
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Optimize LNA check" tried
to use the "rs_firstaggr" flag to optimize the LNA
combining algorithm when processing subframes in
an A-MPDU. This doesn't appear to work well in practice,
so revert it and use the old method of relying on
"rs_moreaggr".
Cc: stable@vger.kernel.org # 3.11
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This might trip up tx completion processing, although the condition that
triggers this should not (yet) occur in practice.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a regression from commit
"ath9k: shrink a few data structures by reordering fields"
When cloning a buffer, the stale flag (part of bf_state now) needs to be
reset after copying the state to prevent tx processing hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit f5ea1100 cleans up the disk to host conversions for
node directory entries, but because a variable is reused in
xfs_node_toosmall() the next node is not correctly found.
If the original node is small enough (<= 3/8 of the node size),
this change may incorrectly cause a node collapse when it should
not. That will cause an assert in xfstest generic/319:
Assertion failed: first <= last && last < BBTOB(bp->b_length),
file: /root/newest/xfs/fs/xfs/xfs_trans_buf.c, line: 569
Keep the original node header to get the correct forward node.
(When a node is considered for a merge with a sibling, it overwrites the
sibling pointers of the original incore nodehdr with the sibling's
pointers. This leads to loop considering the original node as a merge
candidate with itself in the second pass, and so it incorrectly
determines a merge should occur.)
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
[v3: added Dave Chinner's (slightly modified) suggestion to the commit header,
cleaned up whitespace. -bpm]
Determine if we've created a new file by examining the directory change
attribute and/or the O_EXCL flag.
This fixes a regression when doing a non-exclusive create of a new file.
If the FILE_CREATED flag is not set, the atomic_open() command will
perform full file access permissions checks instead of just checking
for MAY_OPEN.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch avoids to dereference the uninitialized data pointer if the
error path is entered before devm_kzalloc is called (or if the allocation
fails). It fixes the following warning:
sound/soc/fsl/imx-sgtl5000.c: In function 'imx_sgtl5000_probe':
sound/soc/fsl/imx-sgtl5000.c:175:18: warning: 'data' may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
After reports from Chris and Josh Boyer of a rare crash in applesmc,
Guenter pointed at the initialization problem fixed below. The patch
has not been verified to fix the crash, but should be applied
regardless.
Reported-by: <jwboyer@fedoraproject.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
of_get_display_timing(s) use of_find_node_by_name
to get child node, this is incorrect, of_get_child_by_name
should be used instead. The patch fixes it.
Small typo is also corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
udev has this nice feature of creating "dead" /dev/<node> device-nodes if
it finds a devnode:<node> modalias. Once the node is accessed, the kernel
automatically loads the module that provides the node. However, this
requires udev to know the major:minor code to use for the node. This
feature was introduced by:
commit 578454ff7e
Author: Kay Sievers <kay.sievers@vrfy.org>
Date: Thu May 20 18:07:20 2010 +0200
driver core: add devname module aliases to allow module on-demand auto-loading
However, uhid uses dynamic minor numbers so this doesn't actually work. We
need to load uhid to know which minor it's going to use.
Hence, allocate a static minor (just like uinput does) and we're good
to go.
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix to return -EINVAL when virtual vertical size smaller than real
instead of 0, as done elsewhere in this function. Also remove dup code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The nice thing about devm_* is that the driver doesn't need to free the
resources but the driver core takes care about that. This also
simplifies the error path quite a bit and removes the wrong check for a
clock pointer being NULL.
Russell King - ARM Linux <linux@arm.linux.org.uk>:
"And this patch also fixes the above: disabling/unpreparing _after_ putting
the thing - which was quite silly... :)"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.
On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.
So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we assume that userspace will shut down the compressed stream
correctly. However, if userspcae dies (e.g. cplay & ctrl-C) we dont
stop the stream before freeing it.
This now checks that the stream is stopped before freeing.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From Nicolas Ferre, first fixes series for 3.12:
- removal of void IRQF_DISABLED flag in timer drivers
- two little fixes in DT for at91sam9x5 family
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: remove IRQF_DISABLED
ARM: at91: at91sam9x5: set default mmc[01] pinctrl-names
ARM: at91: serial: fix wrong pinctrl_usart2_rts
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 'e7f3880cd9b98c5bf9391ae7acdec82b75403776'
tty: Fix recursive deadlock in tty_perform_flush()
introduced a regression where tcflush() does not generate
SIGTTOU for background process groups.
Make sure ioctl(TCFLSH) calls tty_check_change() when
invoked from the line discipline.
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the STI driver by setting cpu_possible_mask to make EMEV2
SMP work as expected together with the ARM broadcast timer.
This breakage was introduced by:
f7db706 ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real hardware clock-event
Without this fix SMP operation is broken on EMEV2 since no
broadcast timer interrupts trigger on the secondary CPU cores.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Trying to read data from the Pegasus Technologies NoteTaker (0e20:0101)
[1] with the Windows App (EasyNote) works natively but fails when
Windows is running under KVM (and the USB device handed to KVM).
The reason is a USB control message
usb 4-2.2: control urb: bRequestType=22 bRequest=09 wValue=0200 wIndex=0001 wLength=0008
This goes to endpoint address 0x01 (wIndex); however, endpoint address
0x01 does not exist. There is an endpoint 0x81 though (same number,
but other direction); the app may have meant that endpoint instead.
The kernel thus rejects the IO and thus we see the failure.
Apparently, Linux is more strict here than Windows ... we can't change
the Win app easily, so that's a problem.
It seems that the Win app/driver is buggy here and the driver does not
behave fully according to the USB HID class spec that it claims to
belong to. The device seems to happily deal with that though (and
seems to not really care about this value much).
So the question is whether the Linux kernel should filter here.
Rejecting has the risk that somewhat non-compliant userspace apps/
drivers (most likely in a virtual machine) are prevented from working.
Not rejecting has the risk of confusing an overly sensitive device with
such a transfer. Given the fact that Windows does not filter it makes
this risk rather small though.
The patch makes the kernel more tolerant: If the endpoint address in
wIndex does not exist, but an endpoint with toggled direction bit does,
it will let the transfer through. (It does NOT change the message.)
With attached patch, the app in Windows in KVM works.
usb 4-2.2: check_ctrlrecip: process 13073 (qemu-kvm) requesting ep 01 but needs 81
I suspect this will mostly affect apps in virtual environments; as on
Linux the apps would have been adapted to the stricter handling of the
kernel. I have done that for mine[2].
[1] http://www.pegatech.com/
[2] https://sourceforge.net/projects/notetakerpen/
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clocksource devices provided by DT can be disabled (status != "okay").
Instead of registering clocksource drivers for disabled nodes, respect
the device's status by skiping disabled nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Some variants of Exynos MCT, namely exynos4210-mct at the moment, use
normal, shared interrupts for local timers. This means that each
interrupt must have correct affinity set to fire only on CPU
corresponding to given local timer.
However after recent conversion of clocksource drivers to not use the
local timer API for local timer initialization any more, the point of
time when local timers get initialized changed and irq_set_affinity()
fails because the CPU is not marked as online yet.
This patch fixes this by moving the call to irq_set_affinity() to
CPU_ONLINE notification, so the affinity is being set when the CPU goes
online.
This fixes a regression introduced by commit
ee98d27df6 ARM: EXYNOS4: Divorce mct from local timer API
which rendered all Exynos4210 based boards unbootable due to
failing irq_set_affinity() making local timers inoperatible.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This commit:
573145f08c
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
replaced a call to the driver's timer initialization by a call to
clocksource_of_init(). However, it failed to select CONFIG_CLKSRC_OF.
Fix this by selecting CONFIG_CLKSRC_OF for Armada370/XP machines.
Without this change the kernel is stuck at: 'Calibrating delay loop...'.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in ohci-hcd. The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does. Rather, it
depends on the hardware adding completed TDs to a "done queue". Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place. As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.
To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired). Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way. If so, it gives back the next URB right away.
This should be applied to all kernels containing commit 815fa7b917
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in uhci-hcd. It should be
applied to all kernels containing commit c44b225077 (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it. As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set. I don't have any way to test this change,
unfortunately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah writes:
xhci: Bug fixes for 3.12.
Hi Greg,
Here's five bug fixes for 3.12.
The first two bugs fix issues with the command cancellation handling,
which can lead to oopses or the xHCI driver attempting to handle
previously-completed transfers. People have been running into oopses
and odd behavior with command cancellation for a couple kernel releases,
so they're marked for stable.
The third patch fixes an issue with USB remote wakeup under xHCI that
can only be reproduced under ChromeOS. As discussed, this fix is not
urgent, and isn't marked for stable.
The fourth patch fixes a race condition between URB cancellation and
userspace clearing an endpoint stall. The fifth patch removes some
annoying dmesg spam when a USB 3.0 device is disconnected, by avoiding
sending a Set SEL request.
Sarah Sharp
These flags were unused by cifs and since the EXT flags have
been moved to common code in uapi/linux/fs.h we won't need
to have a cifs specific copy.
Signed-off-by: Steve French <smfrench@gmail.com>
Since commit b5dc0d10 (drm/imx: kill firstopen callback) the following probe
failure is seen:
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] Initialized imx-drm 1.0.0 20120507 on minor 0
imx-ldb ldb.10: adding encoder failed with -16
imx-ldb: probe of ldb.10 failed with error -16
imx-ipuv3 2400000.ipu: IPUv3H probed
imx-ipuv3 2800000.ipu: IPUv3H probed
imx-ipuv3-crtc imx-ipuv3-crtc.0: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.0 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.1: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.1 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.2: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.2 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.3: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.3 failed with error -16
The reason for the probe failure is that now 'imxdrm->references' is incremented
early in imx_drm_driver_load(), so the following checks in imx_drm_add_crtc()
and imx_drm_add_encoder():
if (imxdrm->references) {
ret = -EBUSY;
goto err_busy;
}
,will always fail.
Instead of manually keeping the references in the imx-drm driver, let's use
drm->open_count.
After this patch, lvds panel is functional on a mx6qsabrelite board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't allow entry to iwctl_siwencodeext if device not open.
This fixes a race condition where wpa supplicant/network manager
enters the function when the device is already closed.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt6656 is prone to resetting on the usb bus.
It seems there is a race condition and wpa supplicant is
trying to open the device via iw_handlers before its actually
closed at a stage that the buffers are being removed.
The device is longer considered open when the
buffers are being removed. So move ~DEVICE_FLAGS_OPENED
flag to before freeing the device buffers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be race condition that the device is ndo_start_xmit
at a point where the device is closing and apTD is NULL resulting
in dead lock.
Add a NULL check to apTD and return NULL to calling functions.
This is more likely on 64 bit systems.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the staging/dgnc [DIGI NEO AND CLASSIC
PCI PRODUCTS] and staging/dgap [DIGI EPCA PCI PRODUCTS]
drivers to the MAINTAINERS file. I am listed as the
maintainer and the driverdev-devel list is the mailing
list for these drivers.
Signed-off-by: Lidza Louina <lidza.louina@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes and one update to the kernel-paramters.txt documentation.
- Fix PV spinlocks triggering jump_label code bug
- Remove extraneous code in the tpm front driver
- Fix ballooning out of pages when non-preemptible
- Fix deadlock when using a 32-bit initial domain with large amount
of memory
- Add xen_nopvpsin parameter to the documentation"
* tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/spinlock: Document the xen_nopvspin parameter.
xen/p2m: check MFN is in range before using the m2p table
xen/balloon: don't alloc page while non-preemptible
xen: Do not enable spinlocks before jump_label_init() has executed
tpm: xen-tpmfront: Remove the locality sysfs attribute
tpm: xen-tpmfront: Fix default durations
Pull device-mapper fixes from Mike Snitzer:
"A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning
target to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps
fix a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but
relatively little memory. To responsibly select a smaller value users
should use the new nr_bios tracepoint info (via commit 75afb352
"block: Add nr_bios to block_rq_remap tracepoint") to determine the
peak number of bios their workloads create"
* tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: add reserved_bio_based_ios module parameter
dm: add reserved_rq_based_ios module parameter
dm: lower bio-based mempool reservation
dm thin: do not expose non-zero discard limits if discards disabled
dm mpath: disable WRITE SAME if it fails
dm-snapshot: fix performance degradation due to small hash size
dm snapshot: workaround for a false positive lockdep warning
dm stats: fix possible counter corruption on 32-bit systems
dm mpath: do not fail path on -ENOSPC
Pull MIPS fixes from Ralf Baechle:
- Fix a comment
- A small cleanup the main purpose of which is to work around an
internal compiler error bug in certain Codesource toolchains.
* git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mm: Move some checks out of 'for' loop in DMA operations
MIPS: cpu-features.h: s/MIPS53/MIPS64/
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few things for -rc2, this time it's all written by me so it
can only be perfect .... right ? :)
So we have the fix to call irq_enter/exit on the irq stack we've been
discussing, plus a cleanup on top to remove an unused (and broken)
stack limit tracking feature (well, make it 32-bit only in fact where
it is used and works properly).
Then we have two things that I wrote over the last couple of days and
made the executive decision to include just because I can (and I'm
sure you won't object .... right ?).
They fix a couple of annoying and long standing "issues":
- We had separate zImages for when booting via Open Firmware vs.
booting via a flat device-tree, while it's trivial to make one that
deals with both
- We wasted a ton of cycles spinning secondary CPUs uselessly at boot
instead of starting them when needed on pseries, thus contributing
significantly to global warming"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Do not start secondaries in Open Firmware
powerpc/zImage: make the "OF" wrapper support ePAPR boot
powerpc: Remove ksp_limit on ppc64
powerpc/irq: Run softirqs off the top of the irq stack
In gadget mode, musb->is_active should be set only when connected to the
host. musb_g_reset() already takes care of it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull x86 fixes from Ingo Molnar:
"An EFI fix and two reboot-quirk fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/reboot: Fix apparent cut-n-paste mistake in Dell reboot workaround
x86/reboot: Add quirk to make Dell C6100 use reboot=pci automatically
x86, efi: Don't map Boot Services on i386
Pull scheduler fixes from Ingo Molnar:
"Three small fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/balancing: Fix cfs_rq->task_h_load calculation
sched/balancing: Fix 'local->avg_load > busiest->avg_load' case in fix_small_imbalance()
sched/balancing: Fix 'local->avg_load > sds->avg_load' case in calculate_imbalance()
Pull perf fixes from Ingo Molnar:
"Assorted standalone fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Add model number for Avoton Silvermont
perf: Fix capabilities bitfield compatibility in 'struct perf_event_mmap_page'
perf/x86/intel/uncore: Don't use smp_processor_id() in validate_group()
perf: Update ABI comment
tools lib lk: Uninclude linux/magic.h in debugfs.c
perf tools: Fix old GCC build error in trace-event-parse.c:parse_proc_kallsyms()
perf probe: Fix finder to find lines of given function
perf session: Check for SIGINT in more loops
perf tools: Fix compile with libelf without get_phdrnum
perf tools: Fix buildid cache handling of kallsyms with kcore
perf annotate: Fix objdump line parsing offset validation
perf tools: Fill in new definitions for madvise()/mmap() flags
perf tools: Sharpen the libaudit dependencies test
My old @it.uu.se email address is going away, so update relevant
files to point to my @gmail.com address instead. In sata_promise.c
just delete the address, people can get it from MAINTAINERS.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The modifications include:
1. Kconfig of Score: we don't support ioremap
2. Missed headfile including
3. There are some errors in other people's commit not checked by us, we fix it now
3.1 arch/score/kernel/entry.S: wrong instructions
3.2 arch/score/kernel/process.c : just some typos
Signed-off-by: Lennox Wu <lennox.wu@gmail.com>
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* It was possible to use an uninitialized buffer when reading
kernel modules information and checking if the file was a
/proc/sys/kernel/kptr_restrict'ed one, fix for this from
Adrian Hunter.
* The libbfd demangler doesn't handle cloned functions (e.g. symbol.clone.NUM),
feed it unsuffixed symbol names, workaround from Andi Kleen.
* Fix segfault in 'perf trace' when processing perf.data files with PERF_RECORD_MMAP2
records, recently added but not handled in this tool, from David Ahern.
* Fix libdl related build in old systems like Fedora 12, from David Ahern.
* Make 'perf kmem' work again on non NUMA machines, fix from Jiri Olsa.
* Fix probing symbols with optimization suffix in 'perf probe' where some
operations that are entirely user level and involves vmlinux/DWARF were working
but when the symbol name was fed to the kprobes tracer, the in kernel code
would use /proc/kallsyms where the name had the suffix, from Masami Hiramatsu.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ASID is represented as an unsigned int in mm_context_t and we
currently use the mmid assembler macro to access this element of the
struct. This should be accessed with a register of 32-bit width. If
the incorrect register width is used the ASID will be returned in
bits[32:63] of the register when running under big-endian.
Fix a use of the mmid macro in tlb.S to use a 32-bit access.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
get_user() is defined as a function macro in arm64, and trace_get_user()
calls it as followed:
get_user(ch, ptr++);
Since the second parameter occurs twice in the definition, 'ptr++' is
unexpectedly evaluated twice and trace_get_user() will generate a bogus
string from user-provided one. As a result, some ftrace sysfs operations,
like "echo FUNCNAME > set_ftrace_filter," hit this case and eventually fail.
This patch fixes the issue both in get_user() and put_user().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
[catalin.marinas@arm.com: added __user type annotation and s/optr/__p/]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix perf probe to probe on some symbols which have some optimzation
suffixes, e.g. ".part", ".isra", and ".constprop".
To fix this issue, instead of using the DIE name, perf probe uses the
symbol name found by dwfl_module_addrsym().
This also involves a perf probe --vars operation update which now shows
the symbol name instead of the DIE name.
Without this patch, putting a probe on an inlined function which was
compiled with a suffixed symbol will fail like this:
$ perf probe -v getname_flags
probe-definition(0): getname_flags
symbol:getname_flags file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Looking at the vmlinux_path (6 entries long)
Using /lib/modules/3.11.0+/build/vmlinux for symbols
found inline addr: 0xffffffff8119bb70
Probe point found: getname_flags+0
found inline addr: 0xffffffff8119bcb6
Probe point found: getname+6
found inline addr: 0xffffffff811a06a6
Probe point found: user_path_at_empty+6
find 3 probe_trace_events.
Opening /sys/kernel/debug//tracing/kprobe_events write=1
Added new events:
Writing event: p:probe/getname_flags getname_flags+0
Failed to write event: No such file or directory
Error: Failed to add events. (-1)
Because the debuginfo knows only the original (non suffix) symbol name,
it uses the original symbol for probe address but the kernel (kallsyms)
knows only suffixed symbol. Then, the kernel rejects that original
symbol.
This patch uses dwfl_module_addrsym() to get the correct (suffixed)
symbol from symtab when a probe point is found.
Reported-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130925131616.31632.46658.stgit@udc4-manage.rcp.hitachi.co.jp
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The check cpu_needs_post_dma_flush() in mips_dma_sync_sg_for_cpu() and
the check !plat_device_is_coherent() in mips_dma_sync_sg_for_device()
can be moved outside the for loop.
As a side effect, this also avoids a GCC bug that caused kernel compile
to fail with the error:
arch/mips/mm/dma-default.c: In function 'mips_dma_sync_sg_for_cpu':
arch/mips/mm/dma-default.c:316:1: internal compiler error: in add_insn_before, at emit-rtl.c:3852
This gcc failure is seen in Code Sourcery toolchains [e.g. gcc version
4.7.2 (Sourcery CodeBench Lite 2012.09-99)] after commit "MIPS: Optimize
current_cpu_type() for better code."
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5907/
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Tested-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Which disables in the ticketlock slowpath the Xen PV optimization's.
Useful for diagnosing issues and comparing benchmarks in
over-commit CPU scenarios.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
On hosts with more than 168 GB of memory, a 32-bit guest may attempt
to grant map an MFN that is error cannot lookup in its mapping of the
m2p table. There is an m2p lookup as part of m2p_add_override() and
m2p_remove_override(). The lookup falls off the end of the mapped
portion of the m2p and (because the mapping is at the highest virtual
address) wraps around and the lookup causes a fault on what appears to
be a user space address.
do_page_fault() (thinking it's a fault to a userspace address), tries
to lock mm->mmap_sem. If the gntdev device is used for the grant map,
m2p_add_override() is called from from gnttab_mmap() with mm->mmap_sem
already locked. do_page_fault() then deadlocks.
The deadlock would most commonly occur when a 64-bit guest is started
and xenconsoled attempts to grant map its console ring.
Introduce mfn_to_pfn_no_overrides() which checks the MFN is within the
mapped portion of the m2p table before accessing the table and use
this in m2p_add_override(), m2p_remove_override(), and mfn_to_pfn()
(which already had the correct range check).
All faults caused by accessing the non-existant parts of the m2p are
thus within the kernel address space and exception_fixup() is called
without trying to lock mm->mmap_sem.
This means that for MFNs that are outside the mapped range of the m2p
then mfn_to_pfn() will always look in the m2p overrides. This is
correct because it must be a foreign MFN (and the PFN in the m2p in
this case is only relevant for the other domain).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@citrix.com>
Cc: Jan Beulich <JBeulich@suse.com>
--
v3: check for auto_translated_physmap in mfn_to_pfn_no_overrides()
v2: in mfn_to_pfn() look in m2p_overrides if the MFN is out of
range as it's probably foreign.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Bit 12 is undefined in any of the following cases:
- If the "NMI exiting" VM-execution control is 1 and the "virtual NMIs"
VM-execution control is 0.
- If the VM exit sets the valid bit in the IDT-vectoring information field
Signed-off-by: Gleb Natapov <gleb@redhat.com>
[Add parentheses around & within && - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Starting secondary CPUs early on from Open Firmware and placing them
in a holding spin loop slows down the boot process significantly under
some hypervisors such as KVM.
This is also unnecessary when RTAS supports querying the CPU state
So let's not do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes the "OF" zImage wrapper (zImage.pseries, zImage.pmac,
zImage.maple) work if booted via a flat device-tree (ePAPR boot
mode), and thus potentially usable with kexec.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've been keeping that field in thread_struct for a while, it contains
the "limit" of the current stack pointer and is meant to be used for
detecting stack overflows.
It has a few problems however:
- First, it was never actually *used* on 64-bit. Set and updated but
not actually exploited
- When switching stack to/from irq and softirq stacks, it's update
is racy unless we hard disable interrupts, which is costly. This
is fine on 32-bit as we don't soft-disable there but not on 64-bit.
Thus rather than fixing 2 in order to implement 1 in some hypothetical
future, let's remove the code completely from 64-bit. In order to avoid
a clutter of ifdef's, we remove the updates from C code completely
during interrupt stack switching, and instead maintain it from the
asm helper that is used to do the stack switching in the first place.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nowadays, irq_exit() calls __do_softirq() pretty much directly
instead of calling do_softirq() which switches to the decicated
softirq stack.
This has lead to observed stack overflows on powerpc since we call
irq_enter() and irq_exit() outside of the scope that switches to
the irq stack.
This fixes it by moving the stack switching up a level, making
irq_enter() and irq_exit() run off the irq stack.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a loop in do_mlockall() that lacks a preemption point, which
means that the following can happen on non-preemptible builds of the
kernel. Dave Jones reports:
"My fuzz tester keeps hitting this. Every instance shows the non-irq
stack came in from mlockall. I'm only seeing this on one box, but
that has more ram (8gb) than my other machines, which might explain
it.
INFO: rcu_preempt self-detected stall on CPU { 3} (t=6500 jiffies g=470344 c=470343 q=0)
sending NMI to all CPUs:
NMI backtrace for cpu 3
CPU: 3 PID: 29664 Comm: trinity-child2 Not tainted 3.11.0-rc1+ #32
Call Trace:
lru_add_drain_all+0x15/0x20
SyS_mlockall+0xa5/0x1a0
tracesys+0xdd/0xe2"
This commit addresses this problem by inserting the required preemption
point.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Much of of_irq.h is needlessly ifdef'ed. Clean this up and minimize the
amount ifdef'ed code. This fixes some build warnings when CONFIG_OF
is not enabled (seen on i386 and x86_64):
include/linux/of_irq.h:82:7: warning: 'struct device_node' declared inside parameter list [enabled by default]
include/linux/of_irq.h:82:7: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
include/linux/of_irq.h:87:47: warning: 'struct device_node' declared inside parameter list [enabled by default]
Compile tested on i386, sparc and arm.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Clean-up some copy/paste declarations that are not necessary. All the
functions either don't exist or are already declared in other headers.
This is needed in preparation of of_irq.h clean-up.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
If 'dvfs_info' is NULL (due to devm_kzalloc failure) the failure
error message would try to dereference it. Use 'pdev' instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_get() can be called from external drivers which might not be aware if
cpufreq driver is registered or not. And so we should actually check if cpufreq
driver is registered or not and also if cpufreq is active or disabled, at the
beginning of cpufreq_get().
Otherwise call to lock_policy_rwsem_read() might hit BUG_ON(!policy).
Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the hw supports intel_pstate and acpi_cpufreq, intel_pstate will
get loaded first.
acpi_cpufreq_init() will call acpi_cpufreq_early_init()
and that will allocate perf data and init those perf data in ACPI core,
(that will cover all CPUs). But later it will free them as
cpufreq_register_driver(acpi_cpufreq) will fail as intel_pstate is
already registered
Use cpufreq_get_current_driver() to check if we can skip the
acpi_cpufreq loading.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes the issues indicated by the test results that
ipmi_msg_handler() is invoked in atomic context.
BUG: scheduling while atomic: kipmi0/18933/0x10000100
Modules linked in: ipmi_si acpi_ipmi ...
CPU: 3 PID: 18933 Comm: kipmi0 Tainted: G AW 3.10.0-rc7+ #2
Hardware name: QCI QSSC-S4R/QSSC-S4R, BIOS QSSC-S4R.QCI.01.00.0027.070120100606 07/01/2010
ffff8838245eea00 ffff88103fc63c98 ffffffff814c4a1e ffff88103fc63ca8
ffffffff814bfbab ffff88103fc63d28 ffffffff814c73e0 ffff88103933cbd4
0000000000000096 ffff88103fc63ce8 ffff88102f618000 ffff881035c01fd8
Call Trace:
<IRQ> [<ffffffff814c4a1e>] dump_stack+0x19/0x1b
[<ffffffff814bfbab>] __schedule_bug+0x46/0x54
[<ffffffff814c73e0>] __schedule+0x83/0x59c
[<ffffffff81058853>] __cond_resched+0x22/0x2d
[<ffffffff814c794b>] _cond_resched+0x14/0x1d
[<ffffffff814c6d82>] mutex_lock+0x11/0x32
[<ffffffff8101e1e9>] ? __default_send_IPI_dest_field.constprop.0+0x53/0x58
[<ffffffffa09e3f9c>] ipmi_msg_handler+0x23/0x166 [ipmi_si]
[<ffffffff812bf6e4>] deliver_response+0x55/0x5a
[<ffffffff812c0fd4>] handle_new_recv_msgs+0xb67/0xc65
[<ffffffff81007ad1>] ? read_tsc+0x9/0x19
[<ffffffff814c8620>] ? _raw_spin_lock_irq+0xa/0xc
[<ffffffffa09e1128>] ipmi_thread+0x5c/0x146 [ipmi_si]
...
Also Tony Camuso says:
We were getting occasional "Scheduling while atomic" call traces
during boot on some systems. Problem was first seen on a Cisco C210
but we were able to reproduce it on a Cisco c220m3. Setting
CONFIG_LOCKDEP and LOCKDEP_SUPPORT to 'y' exposed a lockdep around
tx_msg_lock in acpi_ipmi.c struct acpi_ipmi_device.
=================================
[ INFO: inconsistent lock state ]
2.6.32-415.el6.x86_64-debug-splck #1
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/3/17 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&ipmi_device->tx_msg_lock){+.?...}, at: [<ffffffff81337a27>] ipmi_msg_handler+0x71/0x126
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810ba11c>] __lock_acquire+0x63c/0x1570
[<ffffffff810bb0f4>] lock_acquire+0xa4/0x120
[<ffffffff815581cc>] __mutex_lock_common+0x4c/0x400
[<ffffffff815586ea>] mutex_lock_nested+0x4a/0x60
[<ffffffff8133789d>] acpi_ipmi_space_handler+0x11b/0x234
[<ffffffff81321c62>] acpi_ev_address_space_dispatch+0x170/0x1be
The fix implemented by this change has been tested by Tony:
Tested the patch in a boot loop with lockdep debug enabled and never
saw the problem in over 400 reboots.
Reported-and-tested-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge fixes from Andrew Morton:
"Bunch of fixes.
And a reversion of mhocko's "Soft limit rework" patch series. This is
actually your fault for opening the merge window when I was off racing ;)
I didn't read the email thread before sending everything off.
Johannes Weiner raised significant issues:
http://www.spinics.net/lists/cgroups/msg08813.html
and we agreed to back it all out"
I clearly need to be more aware of Andrew's racing schedule.
* akpm:
MAINTAINERS: update mach-bcm related email address
checkpatch: make extern in .h prototypes quieter
cciss: fix info leak in cciss_ioctl32_passthru()
cpqarray: fix info leak in ida_locked_ioctl()
kernel/reboot.c: re-enable the function of variable reboot_default
audit: fix endless wait in audit_log_start()
revert "memcg, vmscan: integrate soft reclaim tighter with zone shrinking code"
revert "memcg: get rid of soft-limit tree infrastructure"
revert "vmscan, memcg: do softlimit reclaim also for targeted reclaim"
revert "memcg: enhance memcg iterator to support predicates"
revert "memcg: track children in soft limit excess to improve soft limit"
revert "memcg, vmscan: do not attempt soft limit reclaim if it would not scan anything"
revert "memcg: track all children over limit in the root"
revert "memcg, vmscan: do not fall into reclaim-all pass too quickly"
fs/ocfs2/super.c: use a bigger nodestr in ocfs2_dismount_volume
watchdog: update watchdog_thresh properly
watchdog: update watchdog attributes atomically
The arg64 struct has a hole after ->buf_size which isn't cleared. Or if
any of the calls to copy_from_user() fail then that would cause an
information leak as well.
This was assigned CVE-2013-2147.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1b3a5d02ee ("reboot: move arch/x86 reboot= handling to generic
kernel") did some cleanup for reboot= command line, but it made the
reboot_default inoperative.
The default value of variable reboot_default should be 1, and if command
line reboot= is not set, system will use the default reboot mode.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Robin Holt <robinmholt@linux.com>
Cc: <stable@vger.kernel.org> [3.11.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 3b38722efd ("memcg, vmscan: integrate soft reclaim
tighter with zone shrinking code")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit e883110aad ("memcg: get rid of soft-limit tree
infrastructure")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit a5b7c87f92 ("vmscan, memcg: do softlimit reclaim also
for targeted reclaim")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit de57780dc6 ("memcg: enhance memcg iterator to support
predicates")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 7d910c054b ("memcg: track children in soft limit excess
to improve soft limit")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit e839b6a1c8 ("memcg, vmscan: do not attempt soft limit
reclaim if it would not scan anything")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 1be171d60b ("memcg: track all children over limit in the
root")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit e975de998b ("memcg, vmscan: do not fall into reclaim-all
pass too quickly")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While printing 32-bit node numbers, an 8-byte string is not enough.
Increase the size of the string to 12 chars.
This got left out in commit 49fa8140e4 ("fs/ocfs2/super.c: Use bigger
nodestr to accomodate 32-bit node numbers").
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
watchdog_tresh controls how often nmi perf event counter checks per-cpu
hrtimer_interrupts counter and blows up if the counter hasn't changed
since the last check. The counter is updated by per-cpu
watchdog_hrtimer hrtimer which is scheduled with 2/5 watchdog_thresh
period which guarantees that hrtimer is scheduled 2 times per the main
period. Both hrtimer and perf event are started together when the
watchdog is enabled.
So far so good. But...
But what happens when watchdog_thresh is updated from sysctl handler?
proc_dowatchdog will set a new sampling period and hrtimer callback
(watchdog_timer_fn) will use the new value in the next round. The
problem, however, is that nobody tells the perf event that the sampling
period has changed so it is ticking with the period configured when it
has been set up.
This might result in an ear ripping dissonance between perf and hrtimer
parts if the watchdog_thresh is increased. And even worse it might lead
to KABOOM if the watchdog is configured to panic on such a spurious
lockup.
This patch fixes the issue by updating both nmi perf even counter and
hrtimers if the threshold value has changed.
The nmi one is disabled and then reinitialized from scratch. This has
an unpleasant side effect that the allocation of the new event might
fail theoretically so the hard lockup detector would be disabled for
such cpus. On the other hand such a memory allocation failure is very
unlikely because the original event is deallocated right before.
It would be much nicer if we just changed perf event period but there
doesn't seem to be any API to do that right now. It is also unfortunate
that perf_event_alloc uses GFP_KERNEL allocation unconditionally so we
cannot use on_each_cpu() and do the same thing from the per-cpu context.
The update from the current CPU should be safe because
perf_event_disable removes the event atomically before it clears the
per-cpu watchdog_ev so it cannot change anything under running handler
feet.
The hrtimer is simply restarted (thanks to Don Zickus who has pointed
this out) if it is queued because we cannot rely it will fire&adopt to
the new sampling period before a new nmi event triggers (when the
treshold is decreased).
[akpm@linux-foundation.org: the UP version of __smp_call_function_single ended up in the wrong place]
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc_dowatchdog doesn't synchronize multiple callers which might lead to
confusion when two parallel callers might confuse watchdog_enable_all_cpus
resp watchdog_disable_all_cpus (eg watchdog gets enabled even if
watchdog_thresh was set to 0 already).
This patch adds a local mutex which synchronizes callers to the sysctl
handler.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge bcache fixes from Kent Overstreet:
"There's fixes for _three_ different data corruption bugs, all of which
were found by users hitting them in the wild.
The first one isn't bcache specific - in 3.11 bcache was switched to
the bio_copy_data in fs/bio.c, and that's when the bug in that code
was discovered, but it's also used by raid1 and pktcdvd. (That was my
code too, so the bug's doubly embarassing given that it was or
should've been just a cut and paste from bcache code. Dunno what
happened there).
Most of these (all the non data corruption bugs, actually) were ready
before the merge window and have been sitting in Jens' tree, but I
don't know what's been up with him lately..."
* emailed patches from Kent Overstreet <kmo@daterainc.com>:
bcache: Fix flushes in writeback mode
bcache: Fix for handling overlapping extents when reading in a btree node
bcache: Fix a shrinker deadlock
bcache: Fix a dumb CPU spinning bug in writeback
bcache: Fix a flush/fua performance bug
bcache: Fix a writeback performance regression
bcache: Correct printf()-style format length modifier
bcache: Fix for when no journal entries are found
bcache: Strip endline when writing the label through sysfs
bcache: Fix a dumb journal discard bug
block: Fix bio_copy_data()
In writeback mode, when we get a cache flush we need to make sure we
issue a flush to the backing device.
The code for sending down an extra flush was wrong - by cloning the bio
we were probably getting flags that didn't make sense for a bare flush,
and also the old code was firing for FUA bios, for which we don't need
to send a flush to the backing device.
This was causing data corruption somehow - the mechanism was never
determined, but this patch fixes it for the users that were seeing it.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
btree_sort_fixup() was overly clever, because it was trying to avoid
pulling a key off the btree iterator in more than one place.
This led to a really obscure bug where we'd break early from the loop in
btree_sort_fixup() if the current key overlapped with keys in more than
one older set, and the next key it overlapped with was zero size.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GFP_NOIO means we could be getting called recursively - mca_alloc() ->
mca_data_alloc() - definitely can't use mutex_lock(bucket_lock) then.
Whoops.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bch_journal_meta() was missing the flush to make the journal write
actually go down (instead of waiting up to journal_delay_ms)...
Whoops
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background writeback works by scanning the btree for dirty data and
adding those keys into a fixed size buffer, then for each dirty key in
the keybuf writing it to the backing device.
When read_dirty() finishes and it's time to scan for more dirty data, we
need to wait for the outstanding writeback IO to finish - they still
take up slots in the keybuf (so that foreground writes can check for
them to avoid races) - without that wait, we'll continually rescan when
we'll be able to add at most a key or two to the keybuf, and that takes
locks that starves foreground IO. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix
drivers/md/bcache/btree.c: In function ‘bch_btree_node_read’:
drivers/md/bcache/btree.c:259: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 3 has type ‘size_t’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sysfs attributes with unusual characters have crappy failure modes
in Squeeze (udev 164); later versions of udev are unaffected.
This should make these characters more unusual.
Signed-off-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
That switch statement was obviously wrong, leading to some sort of weird
spinning on rare occasion with discards enabled...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_balloon_scratch_page() disables preemption so we cannot call
alloc_page() in between get/put_balloon_scratch_page(). Shuffle bits
around in decrease_reservation() to avoid this.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
xen_init_spinlocks() currently calls static_key_slow_inc() before
jump_label_init() is invoked. When CONFIG_JUMP_LABEL is set (which usually is
the case) the effect of this static_key_slow_inc() is deferred until after
jump_label_init(). This is different from when CONFIG_JUMP_LABEL is not set, in
which case the key is set immediately. Thus, depending on the value of config
option, we may observe different behavior.
In addition, when we come to __jump_label_transform() from jump_label_init(),
the key (paravirt_ticketlocks_enabled) is already enabled. On processors where
ideal_nop is not the same as default_nop this will cause a BUG() since it is
expected that before a key is enabled the latter is replaced by the former
during initialization.
To address this problem we need to move
static_key_slow_inc(¶virt_ticketlocks_enabled) so that it is called
after jump_label_init(). We also need to make sure that this is done before
other cpus start to boot. early_initcall appears to be a good place to do so.
(Note that we cannot move whole xen_init_spinlocks() there since pv_lock_ops
need to be set before alternative_instructions() runs.)
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Added extra comments in the code]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Upon deeper review it was agreed to remove the driver-unique
'locality' sysfs attribute before it is present in a released
kernel.
The attribute was introduced in e2683957fb
during the 3.12 merge window, so this patch needs to go in before
3.12 is released.
The hope is to have a well defined locality API that all the other
locality aware drivers can use, perhaps in 3.13.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
All the default durations were being set to 10 minutes which is
way too long for the timeouts. Normal values for the longest
duration are around 5 mins, and short duration ar around .5s.
Further, these are just the default, tpm_get_timeouts will set
them to values from the TPM (or throw an error).
Just remove them.
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This regression has been introduced in
commit 9f11a9e4e5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 13 00:54:58 2013 +0200
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
Ville brough up the idea that this is just the pipe A quirk gone
wrong.
Note that after resume the bios might or might not have enabled pipe A
already. We have a bit of magic to make sure that on resume we set up
a decent mode for pipe A, but I fear if I just smash pipe A to always
on we'd enable it in a bogus state and hang the hw. Hence the
readback.
v2: Clarify the logic a bit as suggested by Chris. Also amend the
commit message to clarify why we don't unconditionally enable the
pipe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66462
References: https://lkml.org/lkml/2013/8/26/238
Cc: Meelis Roos <mroos@ut.ee>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use |= instead of = as suggested by Chris.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The native TV encoder has it's own flags to adjust sync modes and
enabled interlaced modes which are totally irrelevant for the adjusted
mode. This worked out nicely since the input modes used by both the
load detect code and reported in the ->get_modes callbacks all have no
flags set, and we also don't fill out any of them in the ->get_config
callback.
This changed with the additional sanitation done with
commit 2960bc9cce
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Jul 30 13:36:32 2013 +0300
drm/i915: make user mode sync polarity setting explicit
sinc now the "no flags at all" state wouldn't fit through core code
any more. So fix this up again by explicitly clearing the flags in the
->compute_config callback.
Aside: We have zero checking in place to make sure that the requested
mode is indeed the right input mode we want for the selected TV mode.
So we'll happily fall over if userspace tries to pull us. But that's
definitely work for a different patch series. So just add a FIXME
comment for now.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After a fair number of xfstests runs, xfs/182 started to fail
regularly with a corrupted directory - a directory read verifier was
failing after recovery because it found a block with a XARM magic
number (remote attribute block) rather than a directory data block.
The first time I saw this repeated failure I did /something/ and the
problem went away, so I was never able to find the underlying
problem. Test xfs/182 failed again today, and I found the root
cause before I did /something else/ that made it go away.
Tracing indicated that the block in question was being correctly
logged, the log was being flushed by sync, but the buffer was not
being written back before the shutdown occurred. Tracing also
indicated that log recovery was also reading the block, but then
never writing it before log recovery invalidated the cache,
indicating that it was not modified by log recovery.
More detailed analysis of the corpse indicated that the filesystem
had a uuid of "a4131074-1872-4cac-9323-2229adbcb886" but the XARM
block had a uuid of "8f32f043-c3c9-e7f8-f947-4e7f989c05d3", which
indicated it was a block from an older filesystem. The reason that
log recovery didn't replay it was that the LSN in the XARM block was
larger than the LSN of the transaction being replayed, and so the
block was not overwritten by log recovery.
Hence, log recovery cant blindly trust the magic number and LSN in
the block - it must verify that it belongs to the filesystem being
recovered before using the LSN. i.e. if the UUIDs don't match, we
need to unconditionally recovery the change held in the log.
This patch was first tested on a block device that was repeatedly
causing xfs/182 to fail with the same failure on the same block with
the same directory read corruption signature (i.e. XARM block). It
did not fail, and hasn't failed since.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
It uses a kernel internal structure in it's definition rather than
the user visible structure that is passed to the ioctl.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
When we free an inode, we do so via RCU. As an RCU lookup can occur
at any time before we free an inode, and that lookup takes the inode
flags lock, we cannot safely assert that the flags lock is not held
just before marking it dead and running call_rcu() to free the
inode.
We check on allocation of a new inode structre that the lock is not
held, so we still have protection against locks being leaked and
hence not correctly initialised when allocated out of the slab.
Hence just remove the assert...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Regression introduced by commit 46f9d2e ("xfs: aborted buf items can
be in the AIL") which fails to lock the AIL before removing the
item. Spinlock debugging throws a warning about this.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Currently, IPC mechanisms do security and auditing related checks under
RCU. However, since security modules can free the security structure,
for example, through selinux_[sem,msg_queue,shm]_free_security(), we can
race if the structure is freed before other tasks are done with it,
creating a use-after-free condition. Manfred illustrates this nicely,
for instance with shared mem and selinux:
-> do_shmat calls rcu_read_lock()
-> do_shmat calls shm_object_check().
Checks that the object is still valid - but doesn't acquire any locks.
Then it returns.
-> do_shmat calls security_shm_shmat (e.g. selinux_shm_shmat)
-> selinux_shm_shmat calls ipc_has_perm()
-> ipc_has_perm accesses ipc_perms->security
shm_close()
-> shm_close acquires rw_mutex & shm_lock
-> shm_close calls shm_destroy
-> shm_destroy calls security_shm_free (e.g. selinux_shm_free_security)
-> selinux_shm_free_security calls ipc_free_security(&shp->shm_perm)
-> ipc_free_security calls kfree(ipc_perms->security)
This patch delays the freeing of the security structures after all RCU
readers are done. Furthermore it aligns the security life cycle with
that of the rest of IPC - freeing them based on the reference counter.
For situations where we need not free security, the current behavior is
kept. Linus states:
"... the old behavior was suspect for another reason too: having the
security blob go away from under a user sounds like it could cause
various other problems anyway, so I think the old code was at least
_prone_ to bugs even if it didn't have catastrophic behavior."
I have tested this patch with IPC testcases from LTP on both my
quad-core laptop and on a 64 core NUMA server. In both cases selinux is
enabled, and tests pass for both voluntary and forced preemption models.
While the mentioned races are theoretical (at least no one as reported
them), I wanted to make sure that this new logic doesn't break anything
we weren't aware of.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Acked-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the following scenario the socket is corked:
If the first UDP packet is larger then the mtu we try to append it to the
write queue via ip6_ufo_append_data. A following packet, which is smaller
than the mtu would be appended to the already queued up gso-skb via
plain ip6_append_data. This causes random memory corruptions.
In ip6_ufo_append_data we also have to be careful to not queue up the
same skb multiple times. So setup the gso frame only when no first skb
is available.
This also fixes a shortcoming where we add the current packet's length to
cork->length but return early because of a packet > mtu with dontfrag set
(instead of sutracting it again).
Found with trinity.
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also changed a log message to indicate that memory was not allocated
instead of memory not available!
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my patch c194992cbe ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.
If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]
This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.
This patch should be backported to 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redirect isn't an error condition, it should leave
the error handler without touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redirect isn't an error condition, it should leave
the error handler without touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Intel Vt-D specs, the offset of Invalidation complete
status register should be 0x9C, not 0x98.
See Intel's VT-d spec, Revision 1.3, Chapter 10.4, Page 98;
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
I believe that Joerg Roedel is at least the path through which
drivers/iommu changes should be merged. Add a MAINTAINERS entry to
make this clear, so that he's Cd'd on all relevant patches. This is
relevant for non-AMD/Intel IOMMUs, where get_maintainers.pl doesn't
currently remind anyone to Cc Joerg on patches.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
There are two locks involved in managing the journal lists. The general
reiserfs_write_lock and the journal->j_flush_mutex.
While flush_journal_list is sleeping to acquire the j_flush_mutex or to
submit a block for write, it will drop the write lock. This allows
another thread to acquire the write lock and ultimately call
flush_used_journal_lists to traverse the list of journal lists and
select one for flushing. It can select the journal_list that has just
had flush_journal_list called on it in the original thread and call it
again with the same journal_list.
The second thread then drops the write lock to acquire j_flush_mutex and
the first thread reacquires it and continues execution and eventually
clears and frees the journal list before dropping j_flush_mutex and
returning.
The second thread acquires j_flush_mutex and ends up operating on a
journal_list that has already been released. If the memory hasn't
been reused, we'll soon after hit a BUG_ON because the transaction id
has already been cleared. If it's been reused, we'll crash in other
fun ways.
Since flush_journal_list will synchronize on j_flush_mutex, we can fix
the race by taking a proper reference in flush_used_journal_lists
and checking to see if it's still valid after the mutex is taken. It's
safe to iterate the list of journal lists and pick a list with
just the write lock as long as a reference is taken on the journal list
before we drop the lock. We already have code to handle whether a
transaction has been flushed already so we can use that to handle the
race and get rid of the trans_id BUG_ON.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Commit a3172027 introduced test_transaction as a requirement for
flushing old lists -- but it can never return 1 unless the transaction
has already been flushed.
As a result, we have a routine that iterates the j_realblocks list but
doesn't actually do anything. Since it's been this way since 2006 and
the latency numbers were what Chris expected, let's just rip it out.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
A user has reported an oops in udf_statfs() that was caused by
numOfPartitions entry in LVID structure being corrupted. Fix the problem
by verifying whether numOfPartitions makes sense at least to the extent
that LVID fits into a single block as it should.
Reported-by: Juergen Weigert <jw@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
In
commit edc3d8848d
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 23 13:55:35 2013 +0300
drm/i915: avoid big kmallocs on reading error state
we introduce a two-pass mechanism for splitting long strings being
formatted into the error-state. The first pass finds the length, and the
second pass emits the right portion of the string into the accumulation
buffer. Unfortunately we use the same va_list for both passes, resulting
in the second pass reading garbage off the end of the argument list. As
the two passes are only used for boundaries between read() calls, the
corruption is only rarely seen.
This fixes the root cause behind
commit baf27f9b17
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Jun 29 23:26:50 2013 +0100
drm/i915: Break up the large vsnprintf() in print_error_buffers()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set SEL control urbs cannot be sent to a device in unconfigured state.
This patch adds a check in usb_req_set_sel() to ensure the usb device's
state is USB_STATE_CONFIGURED.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699
Signed-off-by: Florian Wolter <wolly84@web.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
MRP doesn't implement the periodictimer in 802.1Q, so it never retries
if packets get lost. I ran into this problem when MRP sent a MVRP
JoinIn before the interface was fully up. The JoinIn was lost, MRP
didn't retry, and MVRP registration failed.
Tested against Juniper QFabric switches
Signed-off-by: Noel Burton-Krahn <noel@burton-krahn.com>
Acked-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually re-send packets when the T1 timer runs out. This fixes a bug
where packets are waiting on the write queue until disconnection when
no other traffic is outstanding.
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
This patch contains various bug fixes, half of which are SR-IOV related
(some fixing issues in the recently added VF RSS support), while the other fix
a wide assortments of issues in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).
Wait until firmware ack is written before unlocking channel
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.
This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.
Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
and 04bf3011 ("regulator: Support driver probe deferral") this driver
might return -EPROBE_DEFER if a gpio_request or regulator_get fails.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
this driver might return -EPROBE_DEFER if a gpio_request fails.
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Starting with UVD3 message and feedback buffers have their
own 256MB segment, so no need to force them into VRAM any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow user to change the number of IOs that are reserved by
bio-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_bio_based_ios
The default value is RESERVED_BIO_BASED_IOS (16). The maximum allowed
value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_bio_based_ios() for use by DM targets and core
code. Switch to sizing dm-io's mempool and bioset using DM core's
configurable 'reserved_bio_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios
The default value is RESERVED_REQUEST_BASED_IOS (256). The maximum
allowed value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code. Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Bio-based device mapper processing doesn't need larger mempools (like
request-based DM does), so lower the number of reserved entries for
bio-based operation. 16 was already used for bio-based DM's bioset
but mistakenly wasn't used for it's _io_cache.
Formalize difference between bio-based and request-based defaults by
introducing RESERVED_BIO_BASED_IOS and RESERVED_REQUEST_BASED_IOS.
(based on older code from Mikulas Patocka)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Fix issue where the block layer would stack the discard limits of the
pool's data device even if the "ignore_discard" pool feature was
specified.
The pool and thin device(s) still had discards disabled because the
QUEUE_FLAG_DISCARD request_queue flag wasn't set. But to avoid user
confusion when "ignore_discard" is used: both the pool device and the
thin device(s) have zeroes for all discard limits.
Also, always set discard_zeroes_data_unsupported in targets because they
should never advertise the 'discard_zeroes_data' capability (even if the
pool's data device supports it).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
This is a partial revert of c6cf7777a3.
We need to take into account the clk voltage dependencies of the
board. Not doing so can lead to stability issues on certain
boards if the clks exceed the levels in the dep tables.
DPM already takes that into account, so for optimal performance,
use DPM.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch adds a helper function to fetch the max clock
from the voltage clock dependecy tables. Clocks above that
level tend to be unstable and will require additional driver
tweaks in order to work properly.
This patch implemented the helper function to fetch the max clocks
from the dependency tables. The following patches implement the
per-asic clock filtering.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the linear range settings in commit 5ff26a14c3
"regulator: wm831x-ldo: Convert to use linear ranges".
For wm831x_gp_ldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xe:
volt = 0.9-1.6V in 50mV steps
sel <= 0x1f:
volt = 1.7-3.3V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
For wm831x_aldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xc:
volt = 1-1.6V in 50mV steps
sel <= 0x1f
volt = 1.7-3.5V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The some platforms (e.g., ARM) initializes their clocks as
late_initcalls for some unknown reason. So make sure
random_int_secret_init() is run after all of the late_initcalls are
run.
Cc: stable@vger.kernel.org
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
sizeof() is already size_t so there is no need to cast here. Generally,
casting inside the min() macro instead of using min_t() is considered
bad style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Have pinconf_dbg_config_write() return a ssize_t. This fixes the following
compilation warning:
drivers/pinctrl/pinconf.c:617:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/pinctrl/pinconf.c:617:2: warning: (near initialization for ‘pinconf_dbg_pinconfig_fops.write’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch 638591c enabled building the AES assembler code in Thumb2 mode.
However, this code used arithmetic involving PC rather than adr{l}
instructions to generate PC-relative references to the lookup tables,
and this needs to take into account the different PC offset when
running in Thumb mode.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This prevents the linker erroring with:
arm-linux-ld: error: arch/arm/lib/xor-neon.o uses VFP instructions, whereas arch/arm/lib/built-in.o does not
arm-linux-ld: failed to merge target specific data of file arch/arm/lib/xor-neon.o
This is due to the non-neon files being marked as containing FPA data/
instructions (even though they do not) being mixed with files which
contain VFP, which is an incompatible floating point format.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 377747c406 ("ARM: entry: allow ARM-private syscalls to be
restarted") reworked the low-level syscall dispatcher to allow
restarting of ARM-private syscalls. Unfortunately, this relocated the
label used to dispatch a private syscall from the trace path, so that
the invocation would be bypassed altogether!
This causes applications to fail under strace as soon as they rely on
a private syscall (e.g. set_tls):
set_tls(0xb6fad4c0, 0xb6fadb98, 0xb6fb1050, 0xb6fad4c0, 0xb6fb1050)
= -1 ENOSYS (Function not implemented)
This patch fixes the label so that we correctly dispatch private
syscalls from the trace path.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Hutchings says:
====================
Daniel Pieczko fixed two bugs in reset handling that particularly
affected the new SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently on the Lager board NFS timeouts/delays are seen when booting. That
turned out to happen because the SoC's ETH_LINK signal turns on and off after
each packet. It is connected to Micrel KSZ8041 PHY's LED0 signal. Ether LEDs
on the Lager board are named LINK and ACTIVE which corresponds to non-default
01 setting of the PHY control register 1 bits 14-15. The 'sh_eth' driver resets
the PHY when opening the network device, so we have to set the mentioned bits
back to 01 from the default 00 value which causes bouncing of ETH_LINK. That
can be achieved using the PHY platform fixup mechanism if we also modify the
driver to use it..
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since we don't get info about the number of links from the readdir
linfo levels, stat() will return 0 for st_nlink, and in particular,
samba re-exported shares will show directories as files (as samba is
keying off st_nlink before evaluating how to set the dos modebits)
when doing a dir or ls.
Copy nlink to the inode, unless it wasn't provided. Provide
sane values if we don't have an existing one and none was provided.
Signed-off-by: Jim McDonough <jmcd@samba.org>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: David Disseldorp <ddiss@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Prevent NULL pointer dereference in case when radeon_ring_fini() did it's job.
Reading of r100_cp_ring_info and radeon_ring_gfx debugfs entries will lead to a KP if ring buffer was deallocated, e.g. on failed ring test.
Seen on PA-RISC machine having "radeon: ring test failed (scratch(0x8504)=0xCAFEDEAD)" issue.
v2: agd5f: add some parens around ring->ready check
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
CIK uses a different index for 1D DST surfaces compared to SI. Expose
the new index so libdrm_radeon can use it properly for userspace
drivers.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The old implementation was heavy on str* functions and sprintf calls.
This version is more manual, but faster.
Profiling just the printing of a 3 char CAN-id resulted in 60 instructions
for the manual method and over 2000 for the sprintf method. Bear in
mind the profiling was done against libc and not the kernel sprintf.
Together with this rewrite an issue with sending and receiving of RTR frames
has been fixed by Oliver for the cases that the DLC is not zero.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to use the hex ascii functions in case sensitive environments
the array hex_asc_upper[] and the needed functions for hex_byte_pack_upper()
are introduced.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locking is needed, since the the internal buffer for the CAN frames is
changed during the wakeup call. This could cause buffer inconsistencies
under high loads, especially for the outgoing short CAN packet skbuffs.
The needed locks led to deadlocks before commit
"5ede52538ee2b2202d9dff5b06c33bfde421e6e4 tty: Remove extra wakeup from pty
write() path", which removed the direct callback to the wakeup function from the
tty layer.
As slcan.c is based on slip.c the issue in the original code is fixed, too.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the dlc is closed, rfcomm_dev_state_change() tries to release the
port in the case it cannot get a reference to the tty. However this is
racy and not even needed.
Infact as Peter Hurley points out:
1. Only consider dlcs that are 'stolen' from a connected socket, ie.
reused. Allocated dlcs cannot have been closed prior to port
activate and so for these dlcs a tty reference will always be avail
in rfcomm_dev_state_change() -- except for the conditions covered by
#2b below.
2. If a tty was at some point previously created for this rfcomm, then
either
(a) the tty reference is still avail, so rfcomm_dev_state_change()
will perform a hangup. So nothing to do, or,
(b) the tty reference is no longer avail, and the tty_port will be
destroyed by the last tty_port_put() in rfcomm_tty_cleanup.
Again, no action required.
3. Prior to obtaining the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will not 'see' a rfcomm_dev so nothing to
do here.
4. After releasing the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will 'see' an incomplete rfcomm_dev if a
tty reference could not be obtained. Again, the best thing to do here
is nothing. Any future attempted open() will block on
rfcomm_dev_carrier_raised(). The unconnected device will exist until
released by ioctl(RFCOMMRELEASEDEV).
The patch removes the aforementioned code and uses the
tty_port_tty_hangup() helper to hangup the tty.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tx and rx urbs are not deallocated if something goes wrong in peak_usb_start().
The patch fixes error handling to deallocate all the resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
From Sekhar Nori, DaVinci fixes for v3.12-rc2:
- a fix build breakage with DEBUG_LL
- a quell a build-time warning
* tag 'davinci-fixes-for-v3.12-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm365 evm: fix unused variable warning
ARM: davinci: fix build breakage with DEBUG_LL
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper, mvebu fixes for v3.12:
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
* tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu:
ARM: kirkwood: Fix address of second XOR engine
ARM: mvebu: Add clock properties to Armada XP timer node
ARM: mvebu: Add the reference 25 MHz fixed-clock to Armada XP
ARM: Kirkwood: Add missing DT reg property to cpu@0
bus: mvebu: add missing of_node_put() to fix reference leak
ARM: mvebu: add missing of_node_put() to fix reference leak
Signed-off-by: Olof Johansson <olof@lixom.net>
The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Scheduling a reset following an MC reboot event before waiting for
reboot to complete results in a race that can lead to a state where
must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have
been destroyed during the MC reboot.
To avoid MC errors when trying to remove VIs that do not exist, wait
for the MC reboot to complete before scheduling the reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Workaround the SCSI layer's problematic WRITE SAME heuristics by
disabling WRITE SAME in the DM multipath device's queue_limits if an
underlying device disabled it.
The WRITE SAME heuristics, with both the original commit 5db44863b6
("[SCSI] sd: Implement support for WRITE SAME") and the updated commit
66c28f971 ("[SCSI] sd: Update WRITE SAME heuristics"), default to enabling
WRITE SAME(10) even without successfully determining it is supported.
After the first failed WRITE SAME the SCSI layer will disable WRITE SAME
for the device (by setting sdkp->device->no_write_same which results in
'max_write_same_sectors' in device's queue_limits to be set to 0).
When a device is stacked ontop of such a SCSI device any changes to that
SCSI device's queue_limits do not automatically propagate up the stack.
As such, a DM multipath device will not have its WRITE SAME support
disabled. This causes the block layer to continue to issue WRITE SAME
requests to the mpath device which causes paths to fail and (if mpath IO
isn't configured to queue when no paths are available) it will result in
actual IO errors to the upper layers.
This fix doesn't help configurations that have additional devices
stacked ontop of the mpath device (e.g. LVM created linear DM devices
ontop). A proper fix that restacks all the queue_limits from the bottom
of the device stack up will need to be explored if SCSI will continue to
use this model of optimistically allowing op codes and then disabling
them after they fail for the first time.
Before this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: failing WRITE SAME IO with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
device-mapper: multipath: Failing path 8:112.
end_request: I/O error, dev dm-6, sector 4616
dm-6: WRITE SAME failed. Manually zeroing.
end_request: I/O error, dev dm-6, sector 4616
end_request: I/O error, dev dm-6, sector 5640
end_request: I/O error, dev dm-6, sector 6664
end_request: I/O error, dev dm-6, sector 7688
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
end_request: I/O error, dev dm-6, sector 524296
Aborting journal on device dm-6-8.
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
33553920
After this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: WRITE SAME I/O failed with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
0
It should be noted that WRITE SAME support wasn't enabled in DM
multipath until v3.10.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
LVM2, since version 2.02.96, creates origin with zero size, then loads
the snapshot driver and then loads the origin. Consequently, the
snapshot driver sees the origin size zero and sets the hash size to the
lower bound 64. Such small hash table causes performance degradation.
This patch changes it so that the hash size is determined by the size of
snapshot volume, not minimum of origin and snapshot size. It doesn't
make sense to set the snapshot size significantly larger than the origin
size, so we do not need to take origin size into account when
calculating the hash size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The kernel reports a lockdep warning if a snapshot is invalidated because
it runs out of space.
The lockdep warning was triggered by commit 0976dfc1d0
("workqueue: Catch more locking problems with flush_work()") in v3.5.
The warning is false positive. The real cause for the warning is that
the lockdep engine treats different instances of md->lock as a single
lock.
This patch is a workaround - we use flush_workqueue instead of flush_work.
This code path is not performance sensitive (it is called only on
initialization or invalidation), thus it doesn't matter that we flush the
whole workqueue.
The real fix for the problem would be to teach the lockdep engine to treat
different instances of md->lock as separate locks.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.5+
Patch a003a2 (sched: Consider runnable load average in move_tasks())
sets all top-level cfs_rqs' h_load to rq->avg.load_avg_contrib, which is
always 0. This mistype leads to all tasks having weight 0 when load
balancing in a cpu-cgroup enabled setup. There obviously should be sum
of weights of all runnable tasks there instead. Fix it.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Reviewed-by: Paul Turner <pjt@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1379173186-11944-1-git-send-email-vdavydov@parallels.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In busiest->group_imb case we can come to fix_small_imbalance() with
local->avg_load > busiest->avg_load. This can result in wrong imbalance
fix-up, because there is the following check there where all the
members are unsigned:
if (busiest->avg_load - local->avg_load + scaled_busy_load_per_task >=
(scaled_busy_load_per_task * imbn)) {
env->imbalance = busiest->load_per_task;
return;
}
As a result we can end up constantly bouncing tasks from one cpu to
another if there are pinned tasks.
Fix it by substituting the subtraction with an equivalent addition in
the check.
[ The bug can be caught by running 2*N cpuhogs pinned to two logical cpus
belonging to different cores on an HT-enabled machine with N logical
cpus: just look at se.nr_migrations growth. ]
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/ef167822e5c5b2d96cf5b0e3e4f4bdff3f0414a2.1379252740.git.vdavydov@parallels.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In busiest->group_imb case we can come to calculate_imbalance() with
local->avg_load >= busiest->avg_load >= sds->avg_load. This can result
in imbalance overflow, because it is calculated as follows
env->imbalance = min(
max_pull * busiest->group_power,
(sds->avg_load - local->avg_load) * local->group_power) / SCHED_POWER_SCALE;
As a result we can end up constantly bouncing tasks from one cpu to
another if there are pinned tasks.
Fix this by skipping the assignment and assuming imbalance=0 in case
local->avg_load > sds->avg_load.
[ The bug can be caught by running 2*N cpuhogs pinned to two logical cpus
belonging to different cores on an HT-enabled machine with N logical
cpus: just look at se.nr_migrations growth. ]
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/8f596cc6bc0e5e655119dc892c9bfcad26e971f4.1379252740.git.vdavydov@parallels.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull EFI fix from Matt Flemin:
" * Fix WARNING on i386 by only enabling a workaround for x86-64 since
we've never encountered the bug on i386 - Josh Boyer "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Solve the problems around the broken definition of perf_event_mmap_page::
cap_usr_time and cap_usr_rdpmc fields which used to overlap, partially
fixed by:
860f085b74 ("perf: Fix broken union in 'struct perf_event_mmap_page'")
The problem with the fix (merged in v3.12-rc1 and not yet released
officially), noticed by Vince Weaver is that the new behavior is
not detectable by new user-space, and that due to the reuse of the
field names it's easy to mis-compile a binary if old headers are used
on a new kernel or new headers are used on an old kernel.
To solve all that make this change explicit, detectable and self-contained,
by iterating the ABI the following way:
- Always clear bit 0, and rename it to usrpage->cap_bit0, to at least not
confuse old user-space binaries. RDPMC will be marked as unavailable
to old binaries but that's within the ABI, this is a capability bit.
- Rename bit 1 to ->cap_bit0_is_deprecated and always set it to 1, so new
libraries can reliably detect that bit 0 is deprecated and perma-zero
without having to check the kernel version.
- Use bits 2, 3, 4 for the newly defined, correct functionality:
cap_user_rdpmc : 1, /* The RDPMC instruction can be used to read counts */
cap_user_time : 1, /* The time_* fields are used */
cap_user_time_zero : 1, /* The time_zero field is used */
- Rename all the bitfield names in perf_event.h to be different from the
old names, to make sure it's not possible to mis-compile it
accidentally with old assumptions.
The 'size' field can then be used in the future to add new fields and it
will act as a natural ABI version indicator as well.
Also adjust tools/perf/ userspace for the new definitions, noticed by
Adrian Hunter.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Also-Fixed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/n/tip-zr03yxjrpXesOzzupszqglbv@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For some mysterious reason the sample_id field of PERF_RECORD_MMAP went AWOL.
Reported-by: Vince Weaver <vince@deater.net>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* Check for SIGINT in more loops, allowing tools such as 'perf report' to
react faster to Ctrl+C, from Arnaldo Carvalho de Melo.
* Fix objdump line parsing offset validation in the annotate code,
from Adrian Hunter.
* Fix buildid cache handling of kallsyms with kcore, from Adrian Hunter.
* Fix compile with libelf without get_phdrnum, from Adrian Hunter.
* Sharpen the libaudit dependencies test, refusing to build with older
libraries that doesn't have all the functions used by 'perf trace", fix
from Ingo Molnar.
* Fill in new definitions for madvise()/mmap() flags to fix the build in
older systems, from Ingo Molnar.
* Fix old GCC build error in older systems in the kallsyms parsing code in
trace-event-parse.c, from Ingo Molnar.
* Ignore DWARF declaration tags, allowing, for instance, that the
$ perf probe -L getname
command succeeds in showing the source code for the 'getname' kernel
function, telling in which lines probes can be inserted, fix from
Masami Hiramatsu.
* Fix linux/magic.h related build breakage in some systems, fix from
Vinson Lee.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The compilation only looks for linux/magic.h from the default include
paths, which does not include the source tree. This results in a build
error if linux/magic.h is not available or not installed.
For example, this build error occurs on CentOS 5.
$ make -C tools/lib/lk V=1
[...]
gcc -o debugfs.o -c -ggdb3 -Wall -Wextra -std=gnu99 -Werror -O6
-D_FORTIFY_SOURCE=2 -Wbad-function-cast -Wdeclaration-after-statement
-Wformat-security -Wformat-y2k -Winit-self -Wmissing-declarations
-Wmissing-prototypes -Wnested-externs -Wno-system-headers
-Wold-style-definition -Wpacked -Wredundant-decls -Wshadow
-Wstrict-aliasing=3 -Wstrict-prototypes -Wswitch-default -Wswitch-enum
-Wundef -Wwrite-strings -Wformat -fPIC -D_LARGEFILE64_SOURCE
-D_FILE_OFFSET_BITS=64 debugfs.c
debugfs.c:8:25: error: linux/magic.h: No such file or directory
The only symbol from linux/magic.h needed by debugfs.c is DEBUGFS_MAGIC,
and that is already defined in debugfs.h. linux/magic.h isn't providing
any extra symbols and can unincluded. This is similar to the approach by
perf, which has its own magic.h wrapper at
tools/perf/util/include/linux/magic.h
Signed-off-by: Vinson Lee <vlee@twitter.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Vinson Lee <vlee@freedesktop.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1379546200-17028-1-git-send-email-vlee@freedesktop.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When parsing lines from objdump a line containing source code starting
with a numeric label is mistaken for a line of disassembly starting with
a memory address.
Current validation fails to recognise that the "memory address" is out
of range and calculates an invalid offset which later causes this
segfault:
Program received signal SIGSEGV, Segmentation fault.
0x0000000000457315 in disasm__calc_percent (notes=0xc98970, evidx=0, offset=143705, end=2127526177, path=0x7fffffffbf50)
at util/annotate.c:631
631 hits += h->addr[offset++];
(gdb) bt
#0 0x0000000000457315 in disasm__calc_percent (notes=0xc98970, evidx=0, offset=143705, end=2127526177, path=0x7fffffffbf50)
at util/annotate.c:631
#1 0x00000000004d65e3 in annotate_browser__calc_percent (browser=0x7fffffffd130, evsel=0xa01da0) at ui/browsers/annotate.c:364
#2 0x00000000004d7433 in annotate_browser__run (browser=0x7fffffffd130, evsel=0xa01da0, hbt=0x0) at ui/browsers/annotate.c:672
#3 0x00000000004d80c9 in symbol__tui_annotate (sym=0xc989a0, map=0xa02660, evsel=0xa01da0, hbt=0x0) at ui/browsers/annotate.c:962
#4 0x00000000004d7aa0 in hist_entry__tui_annotate (he=0xdf73f0, evsel=0xa01da0, hbt=0x0) at ui/browsers/annotate.c:823
#5 0x00000000004dd648 in perf_evsel__hists_browse (evsel=0xa01da0, nr_events=1, helpline=
0x58b768 "For a higher level overview, try: perf report --sort comm,dso", ev_name=0xa02cd0 "cycles", left_exits=false, hbt=
0x0, min_pcnt=0, env=0xa011e0) at ui/browsers/hists.c:1659
#6 0x00000000004de372 in perf_evlist__tui_browse_hists (evlist=0xa01520, help=
0x58b768 "For a higher level overview, try: perf report --sort comm,dso", hbt=0x0, min_pcnt=0, env=0xa011e0)
at ui/browsers/hists.c:1950
#7 0x000000000042cf6b in __cmd_report (rep=0x7fffffffd6c0) at builtin-report.c:581
#8 0x000000000042e25d in cmd_report (argc=0, argv=0x7fffffffe4b0, prefix=0x0) at builtin-report.c:965
#9 0x000000000041a0e1 in run_builtin (p=0x801548, argc=1, argv=0x7fffffffe4b0) at perf.c:319
#10 0x000000000041a319 in handle_internal_command (argc=1, argv=0x7fffffffe4b0) at perf.c:376
#11 0x000000000041a465 in run_argv (argcp=0x7fffffffe38c, argv=0x7fffffffe380) at perf.c:420
#12 0x000000000041a707 in main (argc=1, argv=0x7fffffffe4b0) at perf.c:521
After the fix is applied the symbol can be annotated showing the
problematic line "1: rep"
copy_user_generic_string /usr/lib/debug/lib/modules/3.9.10-100.fc17.x86_64/vmlinux
*/
ENTRY(copy_user_generic_string)
CFI_STARTPROC
ASM_STAC
andl %edx,%edx
and %edx,%edx
jz 4f
je 37
cmpl $8,%edx
cmp $0x8,%edx
jb 2f /* less than 8 bytes, go to byte copy loop */
jb 33
ALIGN_DESTINATION
mov %edi,%ecx
and $0x7,%ecx
je 28
sub $0x8,%ecx
neg %ecx
sub %ecx,%edx
1a: mov (%rsi),%al
mov %al,(%rdi)
inc %rsi
inc %rdi
dec %ecx
jne 1a
movl %edx,%ecx
28: mov %edx,%ecx
shrl $3,%ecx
shr $0x3,%ecx
andl $7,%edx
and $0x7,%edx
1: rep
100.00 rep movsq %ds:(%rsi),%es:(%rdi)
movsq
2: movl %edx,%ecx
33: mov %edx,%ecx
3: rep
rep movsb %ds:(%rsi),%es:(%rdi)
movsb
4: xorl %eax,%eax
37: xor %eax,%eax
data32 xchg %ax,%ax
ASM_CLAC
ret
retq
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1379009721-27667-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This flag is a NOOP since 2.6.36 and can be removed.
This is an update for 3.11 of a patch already sent for 3.10
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As per datasheet, voltage range for LDOs are as follows:
0000 = 0.9V
...(50mV steps)
01111 = 1.65V
10000 = 1.8V
... (100mV stepns)
11111 = 3.3V
So, there is no selector for 1.65V to 1.8V.
Correcting the range for max_uV for selector between 0 to 15.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace pinctrl_usart2_rts and pinctrl_usart2_cts istead of pinctrl_uart2_*.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The driver cannot be built as a module, so having a MODULE_ALIAS() isn't
useful.
While at it, fix a small typo in the file header comment and make the
module description string consistent with those for earlier Tegra SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have a bug with omapdrm, where omapdrm calls dispc's pm_runtime
function in atomic context, and dispc's pm_runtime is not marked as
irq_safe:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:952
Dispc's runtime PM callbacks are irq safe, so we can just set the
irq_safe flag to fix the issue.
However, in the long term, I'd rather have omapdrm manage the runtime PM
calls in a better way. Calling get/put for every small operation that
touches the dispc registers is very inefficient. It'd be better and
cleaner to have clear "in-use" and "not-in-use" states for dispc, so
that we don't need to do register context restore for small operations,
only to turn dispc off right afterwards.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While using HDMI connector driver with sil9022 encoder
came across issue where connector driver is probed first.
This resulted in error. A deffered probe solved this.
Most connector drivers need a encoder driver as their
video source. This patch ensures we do a probe defferal
if video source is not present for connector drivers.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If neither CONFIG_SND_DM365_AIC3X_CODEC nor CONFIG_SND_DM365_VOICE_CODEC
are defined, we may get warnings like:
arch/arm/mach-davinci/board-dm365-evm.c:179:33: warning: 'dm365_evm_snd_data' defined but not used [-Wunused-variable]
To fix this, just mark the struct as __maybe_unused.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
commit fcf7157 ("ARM: davinci: serial: get rid of davinci_uart_config")
introduced build breakage because of a misplaced
header file include which cause a bunch of errors when
the file is included in assembly code (like debug-macro.S)
Fix the build breakage.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
When reading percpu stats we need to properly reset
the sum when CPU 0 is not present in the possible mask.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
commit c5549571f9 ("ipvs: convert lblcr scheduler to rcu")
allows RCU readers to use dest after calling ip_vs_dest_put().
In the corner case it can race with ip_vs_dest_trash_expire()
which can release the dest while it is being returned to the
RCU readers as scheduling result.
To fix the problem do not allow e->dest to be replaced and
defer the ip_vs_dest_put() call by using RCU callback. Now
e->dest does not need to be RCU pointer.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
commit c2a4ffb70e ("ipvs: convert lblc scheduler to rcu")
allows RCU readers to use dest after calling ip_vs_dest_put().
In the corner case it can race with ip_vs_dest_trash_expire()
which can release the dest while it is being returned to the
RCU readers as scheduling result.
To fix the problem do not allow en->dest to be replaced and
defer the ip_vs_dest_put() call by using RCU callback. Now
en->dest does not need to be RCU pointer.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
commit 578bc3ef1e ("ipvs: reorganize dest trash") added
IP_VS_DEST_STATE_REMOVING flag and RCU callback named
ip_vs_dest_wait_readers() to keep dests and services after
removal for at least a RCU grace period. But we have the
following corner cases:
- we can not reuse the same dest if its service is removed
while IP_VS_DEST_STATE_REMOVING is still set because another dest
removal in the first grace period can not extend this period.
It can happen when ipvsadm -C && ipvsadm -R is used.
- dest->svc can be replaced but ip_vs_in_stats() and
ip_vs_out_stats() have no explicit read memory barriers
when accessing dest->svc. It can happen that dest->svc
was just freed (replaced) while we use it to update
the stats.
We solve the problems as follows:
- IP_VS_DEST_STATE_REMOVING is removed and we ensure a fixed
idle period for the dest (IP_VS_DEST_TRASH_PERIOD). idle_start
will remember when for first time after deletion we noticed
dest->refcnt=0. Later, the connections can grab a reference
while in RCU grace period but if refcnt becomes 0 we can
safely free the dest and its svc.
- dest->svc becomes RCU pointer. As result, we add explicit
RCU locking in ip_vs_in_stats() and ip_vs_out_stats().
- __ip_vs_unbind_svc is renamed to __ip_vs_svc_put(), it
now can free the service immediately or after a RCU grace
period. dest->svc is not set to NULL anymore.
As result, unlinked dests and their services are
freed always after IP_VS_DEST_TRASH_PERIOD period, unused
services are freed after a RCU grace period.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers such as lblc and lblcr require the weight to be as high as the
maximum number of active connections. In commit b552f7e3a9
("ipvs: unify the formula to estimate the overhead of processing
connections"), the consideration of inactconns and activeconns was cleaned
up to always count activeconns as 256 times more important than inactconns.
In cases where 3000 or more connections are expected, a weight of 3000 *
256 * 3000 connections overflows the 32-bit signed result used to determine
if rescheduling is required.
On amd64, this merely changes the multiply and comparison instructions to
64-bit. On x86, a 64-bit result is already present from imull, so only
a few more comparison instructions are emitted.
Signed-off-by: Simon Kirby <sim@hostway.ca>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
There was a deliberate race condition in dm_stat_for_entry() to avoid the
overhead of disabling and enabling interrupts. The race could result in
some events not being counted on 64-bit architectures.
However, on 32-bit architectures, operations on long long variables are
not atomic, so the race condition could cause the counter to jump by 2^32.
Such jumps could be disruptive, so we need to do proper locking on 32-bit
architectures.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Alasdair G. Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Since ENOSPC is a target-side error, dm-mpath should just pass the error
information to upper layer instead of retrying itself with path failover.
Otherwise it will end up failing all paths down while path checkers find
all paths ok.
ENOSPC can now be returned from SCSI device after commit a9d6ceb8
("[SCSI] return ENOSPC on thin provisioning failure").
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We need to let the setup stage complete cleanly even when the HCI device
is rfkilled. Otherwise the HCI device will stay in an undefined state
and never get notified to user space through mgmt (even when it gets
unblocked through rfkill).
This patch makes sure that hci_dev_open() can be called in the HCI_SETUP
stage, that blocking the device doesn't abort the setup stage, and that
the device gets proper powered down as soon as the setup stage completes
in case it was blocked meanwhile.
The bug that this patch fixed can be very easily reproduced using e.g.
the rfkill command line too. By running "rfkill block all" before
inserting a Bluetooth dongle the resulting HCI device goes into a state
where it is never announced over mgmt, not even when "rfkill unblock all"
is run.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
With the addition of the Armada XP reference clock, we can now model
accurately the available clock inputs for the timer: namely, nbclk
and refclk. For each of this clock inputs we assign a name, for the
driver to select as appropriate.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP SoC has a reference 25 MHz fixed-clock that is used in
some controllers such as the timer and the watchdog. This commit adds
a DT representation of this clock through a fixed-clock compatible node.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The kirkwood.dtsi cpu@0 node is missing the mandatory reg property.
This causes of_get_cpu_node() to fail to find the node and as a result
the cpufreq driver fails in its probe function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add of_node_put to properly decrement the refcount when we are
done using a given node.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/mach-mvebu/armada-370-xp.c
arch/arm/mach-mvebu/platsmp.c
Currently, we try to ensure that we use vcnum of 0 on the first
established session on a connection and then try to use a different
vcnum on each session after that.
This is a little odd, since there's no real reason to use a different
vcnum for each SMB session. I can only assume there was some confusion
between SMB sessions and VCs. That's somewhat understandable since they
both get created during SESSION_SETUP, but the documentation indicates
that they are really orthogonal. The comment on max_vcs in particular
looks quite misguided. An SMB session is already uniquely identified
by the SMB UID value -- there's no need to again uniquely ID with a
VC.
Furthermore, a vcnum of 0 is a cue to the server that it should release
any resources that were previously held by the client. This sounds like
a good thing, until you consider that:
a) it totally ignores the fact that other programs on the box (e.g.
smbclient) might have connections established to the server. Using a
vcnum of 0 causes them to get kicked off.
b) it causes problems with NAT. If several clients are connected to the
same server via the same NAT'ed address, whenever one connects to the
server it kicks off all the others, which then reconnect and kick off
the first one...ad nauseum.
I don't see any reason to ignore the advice in "Implementing CIFS" which
has a comprehensive treatment of virtual circuits. In there, it states
"...and contrary to the specs the client should always use a VcNumber of
one, never zero."
Have the client just use a hardcoded vcnum of 1, and stop abusing the
special behavior of vcnum 0.
Reported-by: Sauron99@gmx.de <sauron99@gmx.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Volker Lendecke <vl@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
In cifs_readpages(), we may decide we don't want to read a page after all -
but the page may already have passed through fscache_read_or_alloc_pages() and
thus have marks and reservations set. Thus we have to call
fscache_readpages_cancel() or fscache_uncache_page() on the pages we're
returning to clear the marks.
NFS, AFS and 9P should be unaffected by this as they call read_cache_pages()
which does the cleanup for you.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Add patch to fix 32bit EFI service mapping (rhbz 726701)
Multiple people are reporting hitting the following WARNING on i386,
WARNING: at arch/x86/mm/ioremap.c:102 __ioremap_caller+0x3d3/0x440()
Modules linked in:
Pid: 0, comm: swapper Not tainted 3.9.0-rc7+ #95
Call Trace:
[<c102b6af>] warn_slowpath_common+0x5f/0x80
[<c1023fb3>] ? __ioremap_caller+0x3d3/0x440
[<c1023fb3>] ? __ioremap_caller+0x3d3/0x440
[<c102b6ed>] warn_slowpath_null+0x1d/0x20
[<c1023fb3>] __ioremap_caller+0x3d3/0x440
[<c106007b>] ? get_usage_chars+0xfb/0x110
[<c102d937>] ? vprintk_emit+0x147/0x480
[<c1418593>] ? efi_enter_virtual_mode+0x1e4/0x3de
[<c102406a>] ioremap_cache+0x1a/0x20
[<c1418593>] ? efi_enter_virtual_mode+0x1e4/0x3de
[<c1418593>] efi_enter_virtual_mode+0x1e4/0x3de
[<c1407984>] start_kernel+0x286/0x2f4
[<c1407535>] ? repair_env_string+0x51/0x51
[<c1407362>] i386_start_kernel+0x12c/0x12f
Due to the workaround described in commit 916f676f8 ("x86, efi: Retain
boot service code until after switching to virtual mode") EFI Boot
Service regions are mapped for a period during boot. Unfortunately, with
the limited size of the i386 direct kernel map it's possible that some
of the Boot Service regions will not be directly accessible, which
causes them to be ioremap()'d, triggering the above warning as the
regions are marked as E820_RAM in the e820 memmap.
There are currently only two situations where we need to map EFI Boot
Service regions,
1. To workaround the firmware bug described in 916f676f8
2. To access the ACPI BGRT image
but since we haven't seen an i386 implementation that requires either,
this simple fix should suffice for now.
[ Added to changelog - Matt ]
Reported-by: Bryan O'Donoghue <bryan.odonoghue.lkml@nexus-software.ie>
Acked-by: Tom Zanussi <tom.zanussi@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
A former patch introducing FUSE_I_SIZE_UNSTABLE flag provided detailed
description of races between ftruncate and anyone who can extend i_size:
> 1. As in the previous scenario fuse_dentry_revalidate() discovered that i_size
> changed (due to our own fuse_do_setattr()) and is going to call
> truncate_pagecache() for some 'new_size' it believes valid right now. But by
> the time that particular truncate_pagecache() is called ...
> 2. fuse_do_setattr() returns (either having called truncate_pagecache() or
> not -- it doesn't matter).
> 3. The file is extended either by write(2) or ftruncate(2) or fallocate(2).
> 4. mmap-ed write makes a page in the extended region dirty.
This patch adds necessary bits to fuse_file_fallocate() to protect from that
race.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
The patch fixes a race between mmap-ed write and fallocate(PUNCH_HOLE):
1) An user makes a page dirty via mmap-ed write.
2) The user performs fallocate(2) with mode == PUNCH_HOLE|KEEP_SIZE
and <offset, size> covering the page.
3) Before truncate_pagecache_range call from fuse_file_fallocate,
the page goes to write-back. The page is fully processed by fuse_writepage
(including end_page_writeback on the page), but fuse_flush_writepages did
nothing because fi->writectr < 0.
4) truncate_pagecache_range is called and fuse_file_fallocate is finishing
by calling fuse_release_nowrite. The latter triggers processing queued
write-back request which will write stale data to the hole soon.
Changed in v2 (thanks to Brian for suggestion):
- Do not truncate page cache until FUSE_FALLOCATE succeeded. Otherwise,
we can end up in returning -ENOTSUPP while user data is already punched
from page cache. Use filemap_write_and_wait_range() instead.
Changed in v3 (thanks to Miklos for suggestion):
- fuse_wait_on_writeback() is prone to livelocks; use fuse_set_nowrite()
instead. So far as we need a dirty-page barrier only, fuse_sync_writes()
should be enough.
- rebased to for-linus branch of fuse.git
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Right after the musb_hdrc driver is loaded, the otg default state
is a_idle, and Mode=Host, which are set by musb_host_setup().
This causes the following kernel message during musb gadget
enumeration.
CAUTION: musb: Babble Interrupt Occurred
This patch sets the otg default state to b_idle, and its Mode to
Peripheral.
It has been validated on TI AM335x GP EVM USB0 port with g_zero.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 40d5e0905a,
'n_tty: Fix EOF push handling' introduced a subtle state
change error wrt EOF push handling when the termios is
changed from non-canonical to canonical mode.
Reset line_start to the current read_tail index, not 0.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused tty-reference from dma-rx path which was left after the
recent tty-port conversions.
Also remove a redundant port initialisation while at it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tty_kref leak when tty_buffer_request room fails in dma-rx path.
Note that the tty ref isn't really needed anymore, but as the leak has
always been there, fixing it before removing should makes it easier to
backport the fix.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently reset and enable the SMMU before the device has finished
being probed, so if we fail later on (for example, because we couldn't
request a global irq successfully) then we will leave the device in an
active state.
This patch delays the reset and enabling of the SMMU hardware until
probing has completed.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix fatal kernel-doc error in <linux/regulator/driver.h>:
Error(include/linux/regulator/driver.h:52): cannot understand prototype: 'struct regulator_linear_range '
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[Rewrote first line -- broonie]
Signed-off-by: Mark Brown <broonie@linaro.org>
The TI_EDMA driver unconditionally calls functions provided by the
TI_PRIV_EDMA code, but it doesn't force that to be built-in. If that isn't
otherwise enabled somewhere, you can get build errors like:
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:593: undefined reference to `edma_free_slot'
drivers/built-in.o: In function `edma_terminate_all':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:169: undefined reference to `edma_stop'
drivers/built-in.o: In function `edma_execute':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:122: undefined reference to `edma_write_slot'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:149: undefined reference to `edma_link'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:152: undefined reference to `edma_start'
Make TI_EDMA select TI_PRIV_EDMA to avoid this.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current equation on the comment is wrong.
For linear mapping starting from 0, the equation is (maxV-minV)/stepV + 1.
Since the linear mapping for PALMAS is not all starting from 0, the equation
on the comment is not useful and misleading. Thus remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SNDRV_PCM_FORMAT_S8 isn't supposed to fall through to SNDRV_PCM_FORMAT_S16_LE
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the connection encryption key size information when
the host is playing the peripheral role. We should set conn->enc_key_
size in hci_le_ltk_request_evt, otherwise it is left uninitialized.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
While playing the peripheral role, the host gets a LE Long Term Key
Request Event from the controller when a connection is established
with a bonded device. The host then informs the LTK which should be
used for the connection. Once the link is encrypted, the host gets
an Encryption Change Event.
Therefore we should set conn->pending_sec_level instead of conn->
sec_level in hci_le_ltk_request_evt. This way, conn->sec_level is
properly updated in hci_encrypt_change_evt.
Moreover, since we have a LTK associated to the device, we have at
least BT_SECURITY_MEDIUM security level.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The Linux Kernel Performance project guys have reported that commit
4e7ea81db5 introduces a performance regression for the following fio
workload:
[global]
direct=0
ioengine=mmap
size=1500M
bs=4k
pre_read=1
numjobs=1
overwrite=1
loops=5
runtime=300
group_reporting
invalidate=0
directory=/mnt/
file_service_type=random:36
file_service_type=random:36
[job0]
startdelay=0
rw=randrw
filename=data0/f1:data0/f2
[job1]
startdelay=0
rw=randrw
filename=data0/f2:data0/f1
...
[job7]
startdelay=0
rw=randrw
filename=data0/f2:data0/f1
The culprit of the problem is that after the commit ext4_writepages()
are more aggressive in writing back pages. Thus we have less consecutive
dirty pages resulting in more seeking.
This increased aggressivity is caused by a bug in the condition
terminating ext4_writepages(). We start writing from the beginning of
the file even if we should have terminated ext4_writepages() because
wbc->nr_to_write <= 0.
After fixing the condition the throughput of the fio workload is about 20%
better than before writeback reorganization.
Reported-by: "Yan, Zheng" <zheng.z.yan@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If the user passes an invalid value it leads to an info leak when we
print the error message or it could oops. This is called with user
supplied data from snd_ctl_elem_write().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The ->put() function are called from snd_ctl_elem_write() with user
supplied data. The limit checks here could underflow leading to a
crash.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Currently platform CPU DAI widgets are created in soc_probe_platform and
soc_probe_link_dais. Remove the extra call in soc_probe_link_dais().
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
If CONFIG_OF=n:
drivers/regulator/da9063-regulator.c: In function ‘da9063_parse_regulators_dt’:
drivers/regulator/da9063-regulator.c:712: warning: passing argument 1 of ‘PTR_ERR’ makes pointer from integer without a cast
drivers/regulator/da9063-regulator.c:712: warning: return makes pointer from integer without a cast
Use ERR_PTR() to encode an error code in a pointer.
PTR_ERR() is meant to decode an error code from a pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet (Referred TPS65913), the on-time for LDO is
500micro second. If LDO6 is in vibrator mode then the on-time
is 2000us.
Set the enable_time on regulator descriptor accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling kfree() to clean up the memory obtained from spi_alloc_master() is
wrong as this is done in spi_master_release() when spi_master->dev's refcount
reaches zero.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current interrupt handler calls pm_runtime_suspended() to check if the
device is suspended or not. However, runtime PM status of the device is
only set to suspended once all PM runtime suspend hooks have executed.
In case of Intel Lynxpoint we have the device bound to the ACPI power
domain and its runtime suspend hook will put the device to D3hot (or D3cold
if possible). This means that the device is powered off before its state is
set to runtime suspended. While in this state the device might get an
interrupt that is meant for another device (as the interrupt line is
shared), and because the device is powered off accessing its registers will
return 0xffffffff that the driver misinterprets as an invalid state.
When this happens user will see messages like below on the console:
pxa2xx-spi INT33C0:00: bad message state in interrupt handler
Fix this by checking the status register for ~0 and returning IRQ_NONE in
that case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the following change
---------
commit ad02e84687
Author: Axel Lin <axel.lin@ingics.com>
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
----------
The list_voltage() takes the true value of selector which is
programmed in the register. As per smsp voltage table
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
121 1650000 (0.49V + 116 * 0.1) * RANGE
Hence making n_voltages for smps to 122.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-09-04 10:39:43 +01:00
654 changed files with 5945 additions and 3430 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
