Pull RISC-V fixes from Paul Walmsley:
- Fix swiotlb initialization on systems where DRAM is located above
4GiB (such as the Tenstorrent Blackhole cards)
- Fix an out-of-bounds access in the memory hot-remove code that can
occur on Sv39 and Sv48 systems
- Avoid oopsing during boot if the SBI component of the unaligned
access performance checking code loses a race against __init function
freeing
- Avoid attempting to install the debug-enabled vDSO when it shouldn't
be built due to !CONFIG_MMU
- Avoid some sparse warnings by adding missing __iomem notations in
get_cycles{,_hi}()
- Drop an unnecessary runtime warning in the SiFive errata handler
* tag 'riscv-for-linus-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: vdso: Only try to install vDSO when present
riscv: mm: Fix out-of-bounds page-table walk during memory hot-remove
riscv: drop __init from vec_check_unaligned_access_speed_all_cpus
riscv: mm: fix SWIOTLB initialization for systems with DRAM above 4GB
riscv/sifive: remove warning in errata
riscv: time: Add missing __iomem in get_cycles() and get_cycles_hi()
Pull s390 updates from Vasily Gorbik:
- Fix PCI MMIO write syscall falsely reporting success for mappings not
valid for MMIO when MIO is unavailable by returning -EFAULT
- Fix CPRB parameter buffer overflows in zcrypt CCA AES cipher and ECC
private key conversion by rejecting oversized key tokens
- Fix buffer overreads and length underflow in pkey and zcrypt CCA
token validation by checking length fields against actual buffer
sizes
- Fix out of bounds permission bitmap access in zcrypt EP11 admin CPRB
filtering on custom device nodes by using AP_DOMAINS as the limit
- Fix speculative permission bitmap reads in zcrypt CCA and EP11 admin
CPRB handling by sanitizing user controlled domain indexes
- Fix sensitive key material left in zcrypt CCA clear key import
buffers by scrubbing CPRB and temporary buffers after use
* tag 's390-7.2-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Fix missing mem scrub at clear key import in cca_clr2cipherkey()
s390/zcrypt: Close speculative mem read possibility
s390/zcrypt: Fix wrong domain value verification with EP11 CPRBs
s390/zcrypt: Fix buffer over-read in cca_cipher2protkey
s390/zcrypt: Validate length for CCA ECC private key requests
s390/zcrypt: Validate length for CCA AES cipher key requests
s390/pci: Fix s390_pci_mmio_write syscall error return without MIO
Pull misc x86 fixes from Ingo Molnar:
- Fix the boot-time memcmp() asm implementation's constraints
and optimization properties (Mauricio Faria de Oliveira)
- Move the 0xd0...0xd7 AMD Zen5 model range from the Zen6
range where it mistakenly ended up (Pratik Vishwakarma)
* tag 'x86-urgent-2026-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Carve out a Zen5 models range
x86/boot: Add volatile, clobbers and zero-length test in memcmp()
Pull scheduler fix from Ingo Molnar:
- Fix wakeups of deferred DL servers to be actually deferred (Gabriele
Monaco)
* tag 'sched-urgent-2026-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Use revised wakeup rule only for running dl_server
Pull uprobes fix from Ingo Molnar:
- Fix uretprobes race that can crash the kernel (Breno Leitao)
* tag 'perf-urgent-2026-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
uprobes: Fix NULL pointer dereference in hprobe_expire()
Pull vfs fixes from Christian Brauner:
"binfmt_misc:
- Don't let an 'F' entry pin its own instance.
An entry registered with 'F' opens its interpreter at registration
time and holds that file until the entry is freed, so an entry
nobody removes by hand is only closed once the binfmt_misc
superblock is shut down.
If the interpreter lives on a mount that keeps that superblock
alive the two pin each other and the file is never closed. That's
reachable by pointing the interpreter at the instance itself or by
using the instance as an overlayfs lower layer, and once the mount
namespace is gone there's nothing left to unregister through
either.
- Restore write access when removing an entry.
Registering with the MISC_FMT_OPEN_FILE flag opens the interpreter
via open_exec() which denies write access for as long as the entry
exists, but removal only did filp_close() and never restored it.
The inode's i_writecount stayed permanently negative and opening
the interpreter for writing kept failing with ETXTBSY long after
the entry was gone.
- Use exe_file_deny_write_access() for the interpreter clone so both
sides base their decision on the same mode.
- Reject a flag character as the field delimiter. create_entry() pads
the buffer with the delimiter so the field parsers terminate even
on a truncated string, but check_special_flags() consumes flag
characters instead of scanning for the delimiter.
If the delimiter is itself a flag character the padding stops
acting as a terminator and the scan keeps reading past the end of
the allocation. Such a registration was always rejected, just only
after the out of bounds read has already happened.
- Don't leak the user namespace when the mount fails.
bm_get_tree() hands its reference to get_tree_keyed() and sget_fc()
moves it into sb->s_fs_info, but generic_shutdown_super() only
calls ->put_super() from inside the if (sb->s_root) branch and
bm_fill_super() can fail before either s_root or s_op is in place.
Drop the reference in ->kill_sb() instead, which runs
unconditionally.
netfs:
- Clear PG_private_2 on a copy-to-cache append failure.
- Handle a rolling buffer allocation failure in single-object
writeback and drop the extra folio reference
netfs_write_folio_single() took before the append.
- Release the previously batched readahead folios when
rolling_buffer_load_from_ra() fails in
netfs_prepare_read_iterator()
- Fix the folio_queue ENOMEM in writeback by adding a mempool and
passing gfp flags into the rolling buffer helpers.
iomap:
- Add a separate bio_set for iomap_split_ioend(). It can split bios
that already come from iomap_ioend_bioset and deadlock once that
bioset is exhausted.
afs:
- Set call->async for an asynchronous afs_fs_fetch_data() the way
afs_fs_fetch_data64() already does.
- Subtract subreq->transferred from subreq->len in
afs_fs_fetch_data() rather than adding it.
- Fix a UAF when sending a message"
* tag 'vfs-7.2-rc6.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
iomap: add a separate bio_set for iomap_split_ioend
binfmt_misc: don't leak the user namespace when the mount fails
binfmt_misc: reject a flag character as the field delimiter
binfmt_misc: use exe_file_deny_write_access() for the interpreter clone
binfmt_misc: restore write access when removing an entry
binfmt_misc: don't let an 'F' entry pin its own instance
netfs: Fix folio_queue ENOMEM in writeback by adding a mempool
netfs: release readahead folios on iterator preparation failure
netfs: handle single writeback rolling buffer allocation failure
netfs: clear PG_private_2 on copy-to-cache append failure
afs: Fix UAF when sending a message
afs: Fix afs_fs_fetch_data() to subtract transferred from len
afs: Fix afs_fs_fetch_data() to set call->async
Pull SCSI fixes from James Bottomley"
"No core changes. The largest driver fix is the reversion of threaded
interrupt handlers in UFS and the next is the resume deadlock fix in
hisi_sas which extends into libsas"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Initialize hba->rpmbs list in ufshcd
scsi: mpi3mr: Fix potential deadlock in mpi3mr_fault_uevent_emit
scsi: target: Clear cmd_cnt when initial counter enrollment fails
scsi: zfcp: Fix memory leak during adapter release by destroying gid_pn_req
scsi: ufs: core: Revert "Delegate the interrupt service routine to a threaded IRQ handler"
scsi: ufs: core: Cancel RTC work in active-active suspend
scsi: scsi_debug: Fix REPORT ZONES alloc_len underflow OOB write
scsi: target: iblock: Fix wrong PR ops NULL check for PREEMPT/RELEASE
scsi: ufs: dt-bindings: Add missing mcq reg for qcom,sa8255p-ufshc
scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race
scsi: libiscsi_tcp: Bound SCSI Response data segment to the connection buffer
scsi: libiscsi: Fix stale-data leak into the SCSI sense buffer
Pull dmaengine fixes from Vinod Koul:
- switchtec fix for register programming
- sun6i descriptor reclaim fix
- Intel idxd fixes for double free in error and setup failure
- Qualcomm bam dma command element fix
* tag 'dmaengine-fix-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: qcom: bam_dma: Fix command element mask field for BAM v1.6.0+
dmaengine: idxd: fix fdev setup failure cleanup in idxd_cdev_open()
dmaengine: idxd: fix double free of wq, engine, and group structs
dmaengine: sun6i-dma: Fix reclaim descriptors while terminating DMA
dmaengine: switchtec-dma: fix FIELD_GET misuse when programming SE threshold
Pull i2c fixes from Andi Shyti:
"A set of fixes across several host controller drivers. The largest
part addresses three issues in the i.MX driver, while the remaining
changes fix probe ordering, power management, timeout recovery and
error handling.
amd-mp2:
- unregister callback if adapter registration fails
designware:
- defer probe until child GPIO controllers are bound
imx:
- mark adapter suspended while hardware is powered down
- fix stale slave pointer and shared IRQ registration race
- stop slave timer before clearing slave pointer
iproc:
- reset controller if START_BUSY remains set after timeout
jz4780:
- cache clock rate to avoid clk_get_rate() deadlock
qcom-cci:
- rely on runtime PM helpers for system sleep
spacemit:
- request interrupt after clock initialization"
* tag 'i2c-fixes-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux:
i2c: qcom-cci: drop custom suspend/resume and rely on runtime PM helpers
i2c: imx: Cancel hrtimer before clearing slave pointer
i2c: imx: Fix slave registration race and error handling
i2c: iproc: reset bus after timeout if START_BUSY is stuck
i2c: imx: mark I2C adapter when hardware is powered down
i2c: designware: defer probe if child GpioInt controllers are not bound
i2c: jz4780: Cache host clock rate at probe to prevent CCF prepare_lock deadlock
i2c: amd-mp2: Unregister callback on adapter add failure
i2c: spacemit: request IRQ after controller initialization
Pull Kbuild fixes from Nathan Chancellor:
- Fix regression with MO= when building out of tree kernel modules due
to incorrectly overwriting build tree's Makefile
- Avoid stripping .BTF sections from modules when building debug .rpm
packages
* tag 'kbuild-fixes-7.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: rpm-pkg: Preserve BTF sections in kernel modules during debuginfo stripping
kbuild: Stop modifying $(objtree)/Makefile when building oot-kmods oos
Pull tracing fixes from Steven Rostedt:
- Reset dropped_count in mmio_reset_data()
When mmio_reset_data() is called, it does not reset the dropped_count
so that subsequent runs will have incorrect reporting.
- Add NULL check for mmio_trace_array in logging functions
The functions __trace_mmiotrace_rw() and __trace_mmiotrace_map() may
have the 'tr' variable passed to it as NULL. But they both
dereference it without checking if it is NULL first.
- Check return value of __register_event() in trace_module_add_events()
If __register_event() fails, the __add_event_to_tracers() call after
it will create a file for it. If the module fails to load and its
memory is freed, the file will still point to it and it will not be
removed as the registering of the event did not complete.
Only call __add_event_to_tracers() if the __register_event() was
successful.
- Fix false positive match in regex_match_full()
The regex full matching uses a strncmp() to test against the match
string and the value. It should not match if value is a prefix of the
string to match. Check to make sure the length of the strings match
before comparing.
- Fix reader page read offset for remote buffers
A page swapped in by __rb_get_reader_page_from_remote() retains its
stale read offset, causing subsequent reads to skip events or read
past valid data.
- Fix memory leak of subbuf_ids in rb_allocate_cpu_buffer()
Remote buffers allocate a subbuf_ids array. If the allocator function
fails after it is allocated, it does not free it, resulting in a
memory leak.
* tag 'trace-v7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Fix subbuf_ids memory leak in rb_allocate_cpu_buffer() error path
ring-buffer: Fix reader page read offset for remote buffers
tracing/filters: Fix false positive match in regex_match_full()
tracing: Check return value of __register_event() in trace_module_add_events()
tracing/mmiotrace: Add NULL check for mmio_trace_array in logging functions
tracing/mmiotrace: Reset dropped_count in mmio_reset_data()
Pull ntfs fixes from Namjae Jeon:
- Keep RECALL_ON_OPEN in inode flags when reloading them from
$FILE_NAME
- Check runlist reallocation sizes for negative values and overflow
- Drop stale page cache after shrinking non-resident attributes to
prevent writeback failures and data loss
* tag 'ntfs-for-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/ntfs:
ntfs: drop stale page-cache when shrinking a non-resident attr
ntfs: harden runlist realloc size calculations
ntfs: preserve RECALL_ON_OPEN on WSL special-file reparse points
Pull smb server fixes from Steve French:
- Use memcmp() when comparing fixed-size binary ClientGUIDs, so
embedded NUL bytes are handled correctly
- Reject repeated SMB2 NEGOTIATE requests after dialect selection
This prevents preauth_info leaks, enforces the SMB2 protocol
requirements, and serializes negotiation state updates.
- Fix a use-after-free in __close_file_table_ids() by removing the
volatile file ID from the owning IDR before dropping the IDR
reference
* tag 'v7.2-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: use memcmp() to compare ClientGUIDs
ksmbd: reject repeated SMB2 NEGOTIATE requests
ksmbd: fix use-after-free in __close_file_table_ids()
Pull ata fixes from Damien Le Moal:
- Fix PCI resource initialization in the sata_mv driver to keep legacy
Marvell boards functional (Rosen)
- Fix ahci_ceva driver initialization error path (Radhey)
- Fix libata header file to remove a kernel doc compilation warning
(Randy)
- Increase the timeout for the STANDBY IMMEDIATE command to avoid
suspend failures with drives that are slow to respond to this command
(Matt)
- Fixes for the handling of timed out commands in the presence of
deferred non-NCQ commands, to avoid excessive delays in executing the
error handler (me)
- Disable link power management for a couple of WD drives that have
been identified as not functioning properly when power management is
used (Niklas)
- Fix the device iteration loop when checking for link power management
support to correctly handle port multiplier setups (Niklas)
* tag 'ata-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-sata: fix ata_scsi_lpm_supported() iteration
ata: libata-core: Disable LPM on WD Green 2.5 480GB
ata: libata-core: Disable LPM on some WD drives
scsi: libsas: terminate deferred commands on time out
ata: libata-scsi: schedule deferred atapi command
ata: libata-scsi: terminate deferred commands on time out
ata: libata-eh: Increase STANDBY IMMEDIATE timeout
ata: libata: avoid kernel-doc warnings
ata: ahci_ceva: fix error paths in ceva_ahci_platform_enable_resources()
ata: sata_mv: accept 1 or 2 resources in platform probe
In rb_allocate_cpu_buffer(), cpu_buffer->subbuf_ids is allocated using
kcalloc() when buffer->remote is non-NULL. If a subsequent page allocation
fails (e.g., ring_buffer_desc_page() returns NULL or rb_allocate_pages()
fails), execution jumps to fail_free_reader.
While __free(kfree) automatically frees the outer cpu_buffer structure
at scope exit, kfree(cpu_buffer) does not recursively free nested heap
pointers such as cpu_buffer->subbuf_ids, resulting in a memory leak.
Fix this by explicitly freeing cpu_buffer->subbuf_ids in the
fail_free_reader error unwinding path when cpu_buffer->remote is set.
Link: https://patch.msgid.link/178550740672.380917.6067449683620196150.stgit@devnote2
Fixes: 2e67fabd8b ("ring-buffer: Introduce ring-buffer remotes")
Assisted-by: Antigravity:gemini-3.6-flash
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull block fixes from Jens Axboe:
- A set of fixes for s390/dasd, via Stefan
- Fix for a missing stop of the timeout timer, if a disk has never been
added
- Clear kernel owned fields on ublk setup by default
* tag 'block-7.2-20260731' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
s390/dasd: Fix undersized format-check buffer
s390/dasd: Fix potential NULL pointer dereference
s390/dasd: Fix path verification interrupted by concurrent dasd_sleep_on_immediatly
block: stop the timeout timer when releasing a never added disk
ublk: reset kernel-owned dev_info fields in ublk_ctrl_add_dev()
Pull io_uring fixes from Jens Axboe:
- Fix for a bug in how length caps are handled in multishot, and along
with it, a generic fix for avoiding these kinds of conversion issues
in the future.
- Ensure that task restrictions are always preserved across exec.
- Revert of the io_uring controlled epoll restriction, which disallowed
nested contexts. Turns out that libuv is already using it like that,
so we cannot simply remove it, sadly.
- Fix for a reference leak in the zcrx code.
* tag 'io_uring-7.2-20260731' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring: preserve task restrictions across exec
io_uring/zcrx: don't clear master_ctx from the import path
Revert "io_uring/epoll: disallow adding an epoll file to an epoll context"
io_uring/kbuf: cap buffer selection length at MAX_RW_COUNT
io_uring/net: initialize mshot_len for send
Pull drm fixes from Dave Airlie:
"Weekly pulls request. As expected there is more AMD this week since
Alex was off last week, vmwgfx looks to have been hit with the AI
stick a bit and mediatek as well. Otherwise some minor fixes across
the board, the new normal definitely seems to be a thing.
dp:
- Restrict some DP bandwidth calculations to HDMI DFP
bridge:
- Fix small leak in bridge/display-connector
mediatek:
- Check CRTC state before freeing
- mtk_hdmi: Fix DDC adapter double put in v2
- mtk_hdmi_common: take i2c adapter module reference
- mtk_dsi: Enable HS clock only at pre-enable
- ovl_adaptor: balance component registrations
amdgpu:
- VCN 5.3 fix
- UserQ fixes
- GEM close optimization
- HDMI AV mute fix
- UML build fixes
- GFXOFF residency metrics fixes
- SMU 15 fixes
- debug_vm fix
- PSP 15 fixes
- NBIO 7.11.5 fix
- pptable use after free fix
- gpu metrics fetch fix
- DC viewport fix
- DML2.1 fix
- i2c retimer spam fix
- UMD profile pstate fix
- Power metrics format cleanup
- GTT size fix on APUs
- DC context logging fix
- PM sysfs fix for APUs
- Follow on pageflip timeout fix
amdkfd:
- Various bounds checking fixes
- Mutex locking fix
i915/xe:
- Check no-DMA huge-pte cases before DMA segment test
- sink FRL rate fix
- 200ms fix for TMDS scrambler status
vmwgfx:
- Improve various size checks and limit checks
- Fix oops when submitting invalid execbuf ioctl
- Correctly lock in vmfwgx fence signaling path
- More validation of execbuf ioctl
- Fix oops in vmwgfx vkms init failure path
- Overflow handling in shader path
panthor:
- Improve firmware validation
imagination:
- Improve imagination trace points.
qaic:
- Fix QAIC transaction length check"
* tag 'drm-fixes-2026-08-01' of https://gitlab.freedesktop.org/drm/kernel: (59 commits)
drm/i915/hdmi: Poll for 200 msec for TMDS_Scrambler_Status
drm/amd/display: Exit idle optimizations before programming
drm/amd/pm: hide pp_table sysfs on APUs
accel/qaic: use sizeof(*trans_hdr) for transaction length check
drm/panthor: validate firmware interface structure sizes
drm/xe/pt: check no-DMA huge-pte cases before DMA segment test
drm/imagination: Update the trace point pvr_job_submit_fw()
drm/i915/dp: Ignore the sink's DSC max FRL rate without a PCON DSC encoder
drm/mediatek: ovl_adaptor: balance component registrations
drm/mediatek: mtk_dsi: Enable HS clock only at pre-enable
drm/dp: Read the PCON max FRL bandwidth only for HDMI DFPs
drm/amd/display: use proper context for logging
drm/amdgpu: cap GTT size to physical RAM on APUs
drm/amd/pm: use milliwatts for GPU power sensors
drm/amdgpu: restore UMD profile pstate after runtime resume
drm/amd/display: Silence link_dpms I2C retimer failures
drm/amdkfd: hold event_mutex while checkpointing CRIU events
drm/amd/display: check if dml21_add_phantom_plane() is successful
drm/amd/display: Fix divide-by-zero in calculate_mcache_setting on zero viewport
drm/amd/display: Add AV mute wait frames to dce110_set_avmute
...
Pull devicetree fixes from Rob Herring:
- Fix NULL bus dereference in of_pci_range_parser_one()
- Prevent out-of-bounds access when too many dynamic reserved memory
regions are defined
* tag 'devicetree-fixes-for-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/address: Fix NULL bus dereference in of_pci_range_parser_one()
of: reserved_mem: prevent OOB when too many dynamic regions are defined
Pull hyper-v fixes from Wei Liu:
- Multiple fixes for the MSHV driver (Stanislav Kinsburskii, Wei Liu,
Yi Xie, Yousef Alhouseen)
- Multiple fixes for the VMBus driver (Hardik Garg, Michael Kelley,
Sebastian Andrzej Siewior)
* tag 'hyperv-fixes-signed-20260731' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
mshv_vtl: bounds-check cpu index in vtl mmap fault handler
mshv: Publish VP to pt_vp_array before installing the file descriptor
Drivers: hv: vmbus: add VTL2 redirect connection ID
mshv: Order pt_vp_array publish against irqfd assertion path
mshv: Fix missing error code on VP allocation failure
mshv: Fix level-triggered check on uninitialized data
mshv: Fix race in mshv_irqfd_deassign
mshv: Use kfree_rcu in mshv_portid_free
mshv: Fix sleeping under spinlock in mshv_portid_alloc
mshv: Fix duplicate GSI detection for GSI 0
Drivers: hv: vmbus: Remove vmbus_irq_initialized
Drivers: hv: vmbus: Replace lockdep_hardirq_threaded() with lockdep annotation
mshv_vtl: fix fd leak in mshv_ioctl_create_vtl()
mshv_vtl: clear hypercall output before copyout
Drivers: hv: vmbus: Set DMA coherent mask for VMBus devices
mshv: fix hv_input_get_system_property struct
Pull RTLA fix from Steven Rostedt:
- Fix timerlat top actions triggering on signal
Fix a bug in RTLA's timerlat top actions feature where on-threshold
actions are triggered on any signal, regardless of whether a latency
spike had actually occurred during the measurement.
The return retval was checked for non-zero to do actions. But if a
signal came in, it returns a negative and actions were being
incorrectly triggered when they should not have been.
* tag 'trace-tools-v7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rtla/timerlat_top: Fix on-threshold actions firing on signal
cpu is taken from pgoff & 0xffff. cpu_online() does not reject cpu >=
nr_cpu_ids, and per_cpu_ptr() can then walk off __per_cpu_offset.
Signed-off-by: Yi Xie <xieyi@kylinos.cn>
Reviewed-by: Naman Jain <namjain@linux.microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
mshv_partition_ioctl_create_vp() called anon_inode_getfd() before
publishing the new VP into partition->pt_vp_array. anon_inode_getfd()
includes fd_install(), so the fd was live in current->files before the
publish ran.
A concurrent MSHV_RUN_VP ioctl on that fd does not serialise against the
in-progress MSHV_CREATE_VP — it takes vp->vp_mutex, not the partition
mutex. Once the VP starts running and traps, mshv_intercept_isr() can look
up partition->pt_vp_array[vp_index] and observe NULL, silently dropping the
intercept message.
Split the fd creation: reserve an fd with get_unused_fd_flags(), create the
file with anon_inode_getfile(), publish the VP via smp_store_release(), and
finally call fd_install() as the userspace-visibility commit point.
Fixes: 621191d709 ("Drivers: hv: Introduce mshv_root module to expose /dev/mshv to VMMs")
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
VMBus sends CHANNELMSG_INITIATE_CONTACT through a Hyper-V message
connection ID. Older protocol versions use VMBUS_MESSAGE_CONNECTION_ID,
while protocol version 5.0 and newer normally use
VMBUS_MESSAGE_CONNECTION_ID_4.
For a VTL2 kernel using VMBus protocol 5.0 or newer, the host
may expect INITIATE_CONTACT on either the redirect connection ID or
VMBUS_MESSAGE_CONNECTION_ID_4. There is no capability indication that
identifies which ID is active, so the driver must determine it at runtime.
During VMBus negotiation, the redirect ID is tried first because it is
used by VTL2 configurations with VMBus redirection enabled. If the
redirect ID is unavailable, the host rejects it synchronously with
HV_STATUS_INVALID_CONNECTION_ID, allowing fallback to the standard ID.
Return a distinct error for an invalid Initiate Contact connection ID so
this fallback does not mask other post-message failures or
protocol-version rejections. Preserve the existing connection ID
selection for older protocol versions or when running below VTL2.
Signed-off-by: Hardik Garg <hargar@linux.microsoft.com>
Reviewed-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
mshv_partition_ioctl_create_vp() initialises a VP struct (allocations,
mutex_init, init_waitqueue_head, page mappings) and then publishes the
pointer into partition->pt_vp_array. Several ISR paths read this array
locklessly: the intercept ISR, the two scheduler ISRs, and
mshv_try_assert_irq_fast() on the irqfd fast path.
Of these, only mshv_try_assert_irq_fast() can structurally race the
publish. It runs from an eventfd waker without holding pt_mutex, and
MSHV_IRQFD does not require the target lapic_apic_id (== vp_index) to
refer to an existing VP at registration time. A user can therefore
register an irqfd targeting a yet-to-be-created VP, then trigger
mshv_try_assert_irq_fast() concurrently with MSHV_CREATE_VP for the
same index. On weakly-ordered architectures the reader can observe a
non-NULL pointer in pt_vp_array before the initialising stores to the
VP struct become visible, leading to use of partially-initialised
fields (e.g. vp_register_page).
The other ISR readers cannot reach this race: the hypervisor will not
generate intercept or scheduler messages for a VP that has never been
told to run, and the user can only call MSHV_RUN_VP on the VP fd
returned by MSHV_CREATE_VP, which by construction is returned after
the publish. Leave those readers as plain loads.
Use smp_store_release() in mshv_partition_ioctl_create_vp() to publish
the pointer, and pair it with smp_load_acquire() in
mshv_try_assert_irq_fast(). On x86 these compile to plain accesses
under TSO; on ARM64 they emit one-instruction acquire/release barriers,
acceptable on this fast path.
The destroy-side path (destroy_partition() clearing pt_vp_array[i] to
NULL after kfree(vp)) has a separate ordering and lifetime concern
that is out of scope here.
Fixes: 621191d709 ("Drivers: hv: Introduce mshv_root module to expose /dev/mshv to VMMs")
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
In mshv_partition_ioctl_create_vp(), when kzalloc for the VP struct
fails, the code jumps to the cleanup path without setting ret. At that
point ret is 0 from the preceding successful mshv_vp_stats_map() call,
so the function returns success to userspace despite having failed to
create the VP. No fd is installed and no VP is registered in pt_vp_array,
but userspace has no way to know the operation failed.
Set ret to -ENOMEM before jumping to the cleanup path.
Fixes: 621191d709 ("Drivers: hv: Introduce mshv_root module to expose /dev/mshv to VMMs")
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
In mshv_irqfd_assign(), the level-triggered validation for resample
irqfds checks irqfd_lapic_irq.lapic_control.level_triggered before
mshv_irqfd_update() has populated the field. Since the irqfd struct is
zero-allocated, level_triggered is always 0 at that point, causing the
check to always reject resample irqfds with -EINVAL. This makes
level-triggered interrupt resampling — used to avoid interrupt storms
with assigned devices — completely non-functional.
Move the check after the mshv_irqfd_update() call, which resolves the
IRQ routing entry and populates irqfd_lapic_irq with the actual trigger
mode.
Fixes: 621191d709 ("Drivers: hv: Introduce mshv_root module to expose /dev/mshv to VMMs")
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
mshv_irqfd_deactivate() and the hlist traversal of pt_irqfds_list
require pt->pt_irqfds_lock to be held, but mshv_irqfd_deassign()
omits it. This races with the EPOLLHUP path in mshv_irqfd_wakeup(),
which does take the lock before calling mshv_irqfd_deactivate().
Additionally, mshv_irqfd_deactivate() uses hlist_del() which poisons
the node pointers rather than resetting them. Since
mshv_irqfd_is_active() relies on hlist_unhashed() (checks pprev ==
NULL), a poisoned node still appears active. If a concurrent path calls
mshv_irqfd_deactivate() again on the same irqfd, the guard fails to
prevent a double hlist_del() on poisoned pointers.
Fix both issues:
- Add the missing spin_lock_irq/spin_unlock_irq around the list
traversal in mshv_irqfd_deassign(), matching mshv_irqfd_release().
- Use hlist_del_init() instead of hlist_del() so the node is properly
marked as unhashed after removal, making the is_active guard reliable.
Fixes: 621191d709 ("Drivers: hv: Introduce mshv_root module to expose /dev/mshv to VMMs")
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
mshv_portid_free() uses synchronize_rcu() followed by kfree() to
reclaim port table entries. This blocks the caller until a full RCU
grace period elapses, which is unnecessary since the same module already
uses the non-blocking kfree_rcu() pattern in mshv_port_table_fini().
Replace with kfree_rcu() to avoid the blocking wait and keep the
reclamation strategy consistent across the file.
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Reviewed-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Pull spi fixes from Mark Brown:
"The drip of driver specific fixes, mostly from the device vendors
themselves, keeps on coming in. There's more than I'd like right now
but equally nothing hugely alarming"
* tag 'spi-fix-v7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-nxp-fspi: propagate clock reconfig failures in nxp_fspi_select_mem()
spi: spi-nxp-fspi: enter stop mode before reconfiguring MCR0 and DLL
spi: spi-nxp-fspi: add per-SoC SDR/DTR clock rate limits for all supported SoCs
spi: spi-qpic-snand: write the feature value before executing SET_FEATURE
spi: spi-cadence: Move TX FIFO full busy-wait into FIFO
spi: qcom-qspi: Correct max DMA length to avoid 64K boundary failure
spi: spacemit: prepare both DMA descriptors before submitting
Pull pci fixes from Bjorn Helgaas:
- Remove Karthikeyan Mitran from Mobiveil MAINTAINERS PCIe entry since
email bounces (Manivannan Sadhasivam)
- Preserve i.MX6Q, i.MX6QP, and i.MX6SX Root Port MSI/MSI-X
Capabilities when using iMSI-RX to work around hardware defect
(Soeren Moch)
- Reorder i.MX6Q/DL PHY power up to fix boot hang regression (Richard
Zhu)
* tag 'pci-v7.2-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: imx6: Fix i.MX6Q/DL boot hang caused by improper PHY power sequencing
PCI: imx6: Keep i.MX6 Root Port MSI/MSI-X Capabilities with iMSI-RX to work around hardware bug
MAINTAINERS: Drop Karthikeyan Mitran from Mobiveil PCIe entry
Pull hwmon fixes from Guenter Roeck:
"Most of the patches are fixes for pre-existing issues reported by
Sashiko. I suspect we'll see a lot of those for a while.
- adt7470:
- Fix PWM auto temp state array and bounds check
- Fix divide-by-zero TOCTOU crash in fan speed read
- Use cached PWM frequency value
- Fix swapped PWM3 and PWM4 auto mode masks
- Fix temperature alarm logic in hwmon_temp_read()
- Fix busy-loop and I2C flooding in update thread
- Fix cache updated before hardware write on I2C error
- Fix fans stuck in manual mode on I2C errors
- ina2xx: Fix various overflow issues
- ltc4282: Fix reading the minimum alarm voltage
- lm63: Mask PWM frequency multiplier to supported bits
- lm90: Only report alarms if driver is ready
- nct6775-core:
- Prevent access to unsupported weight registers
- Fix number of temperature registers for NCT6116
- npcm750-pwm-fan: stop fan timer on device detach
- nzxt-smart2: DMA-align output buffer
- pmbus:
- Fix return value from pmbus_update_byte_data()
- Notify on the hwmon device, not the i2c client
- sht3x: Fix unaligned accesses"
* tag 'hwmon-for-v7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (npcm750-pwm-fan): stop fan timer on device detach
hwmon: (pmbus) Fix return value from pmbus_update_byte_data()
hwmon: (adt7470) Fix PWM auto temp state array and bounds check
hwmon: (adt7470) Fix divide-by-zero TOCTOU crash in fan speed read
hwmon: (adt7470) Use cached PWM frequency value
hwmon: (adt7470) Fix swapped PWM3 and PWM4 auto mode masks
hwmon: (adt7470) Fix temperature alarm logic in hwmon_temp_read()
hwmon: (adt7470) Fix busy-loop and I2C flooding in update thread
hwmon: (adt7470) Fix cache updated before hardware write on I2C error
hwmon: (adt7470) Fix fans stuck in manual mode on I2C errors
hwmon: (nct6775-core) Prevent access to unsupported weight registers
hwmon: (lm63) Mask PWM frequency multiplier to supported bits
hwmon: (nzxt-smart2) DMA-align output buffer
hwmon: (lm90) Only report alarms if driver is ready
hwmon: (sht3x) Fix unaligned accesses
hwmon: (ltc4282) Fix reading the minimum alarm voltage
hwmon: (ina2xx) Fix various overflow issues
hwmon: (pmbus/core) notify on the hwmon device, not the i2c client
hwmon: (nct6775-core) Fix number of temperature registers for NCT6116
Pull sound fixes from Takashi Iwai:
"A collection of sound fixes for the 7.2-rc6 cycle. Again, it became
far larger than wished; I'll throttle from now on.
There are no major changes, just a normal flow of small fixes. The
majority of them are device-specific quirks and ASoC SDCA/codec
updates, but it includes a few ALSA core fixes as well.
ALSA Core:
- Fix for ALSA sequencer timer division-by-zero
- Fix potential race in ALSA timer core
- Wake up linked drain waiters on PCM stream unlink
- Fix double-free of converter objects on UMP rawmidi error path
USB-audio:
- Fix a few potential out-of-bounds access bugs
- Prevent stack info leak in RME Digiface status
- Fix UAF during UMP endpoint destruction
- Fix UAF at error handling during probe in Line6 6fire driver
- Quirks for C-Media CM6206, Corsair Virtuoso, Razer Barracuda X 2.4,
JKY Technology, and generic USB headphones
HD-audio:
- Quirks for HP Victus 16, HP Dragonfly Folio G3, Lenovo Legion 7, HP
Laptop 14s, Acer Nitro 5, TongFang X6SP45xU, Infinix INBOOK X3, and
HP Pavilion All-in-One
ASoC:
- Comprehensive cleanups and bug fixes for SoundWire/SDCA drivers
- DMI quirks for AMD ACP/YC on Lenovo Legion 7, Acer Aspire, MSI
Crosshair A16, and ASUS ExpertBook
- ACPI match table entry for SOF RT5682 on Intel Nova Lake
- Device-specific mixer / clock, irq fixes for TI TAS2562, TI
TAS2781, Sophgo cv1800b ADC, Maxim MAX98090/98095, FSL ASRC/EASRC
and Realtek RT5640"
* tag 'sound-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (53 commits)
ASoC: rt722: reset codec to fix abnormal sound
ASoC: dt-bindings: realtek,rt5640: Make interrupts optional
ALSA: hda/realtek: Add mute LED quirk for HP Victus 16-e0xxx (MB 88ED)
ALSA: usb-audio: Add GET_SAMPLE_RATE quirk for C-Media CM6206
ALSA: usb-audio: Clamp frame size in implicit-feedback mode
ALSA: usb-audio: Fix DMA buffer out-of-bounds write when fill_max is set
ALSA: usb-audio: Add quirk for Corsair Virtuoso (later revision)
ALSA: pcm: wake linked drain waiters on unlink
ASoC: amd: acp: Add DMI quirk for Lenovo Legion 7 15ASH11
ASoC: sophgo: return 1 on volume change in cv1800b_adc_volume_set()
ASoC: tas2781: Use correct calibration data for SINEGAIN2 register
ASoC: SDCA: Move kcontrol search out of IRQ
ASoC: SDCA: Switch to fixup_controls callback for IRQ registration
ASoC: Add a component fixup_controls callback
ASoC: SDCA: Populate IRQ data earlier
ASoC: SDCA: Remove devm from primary IRQ cleanup
ASoC: SDCA: Add sdca_irq_cleanup_late()
ASoC: SDCA: Rename sdca_irq_allocate() to include devm
ALSA: hda/realtek: Add quirk for HP Dragonfly Folio G3 2-in-1 (103c:8a05)
ALSA:hda/realtek:ALC269 fixup for Legion 7 15ASH11 Mic Mute LED
...
Pull UML fix from Richard Weinberger:
- Fix use-after-free in UML's vector networking driver
* tag 'uml-for-linus-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux:
um: vector: fix use-after-free in vector_mmsg_rx()
Pull misc fixes from Andrew Morton:
"12 hotfixes. 6 are cc:stable. 9 are for MM.
There's a two-patch series from Nico which fixes a couple of PMD level
mTHP accounting bugs and a two-patch series from Chris Gellermann
which addresses mishandling of getline() in selftests. All the
remainder are singletons - please see the changelogs for details"
* tag 'mm-hotfixes-stable-2026-07-30-19-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
selftests/mm: fix potential wild pointer access of getline due to missing init
selftests/clone3: fix wild pointer access of getline due to missing init
mm/page_reporting: use system_freezable_wq to fix UAF during suspend
mm: vmscan: abort proactive reclaim early when freezing for suspend
MAINTAINERS: update Nico Pache's email address
arm64, mailmap: update email address for Peter Collingbourne
MAINTAINERS: update address for Burak Emir
mm/huge_memory: unlock i_mmap_rwsem before releasing after-split folios
riscv/mm: use physical alignment for vmemmap_start_pfn
mm/migrate: exclude hugetlb folios from MTHP_STAT_NR_ANON accounting
mm: decrement MTHP_STAT_NR_ANON in free_zone_device_folio()
mm: memcg: initialize *locked in memcg1_oom_prepare() stub
fmt_buffer_size in dasd_eckd_check_device_format() is declared as
int, even though one of the multiplicands, sizeof(struct eckd_count),
is a size_t. The expression
trkcount * rpt_max * sizeof(struct eckd_count)
is therefore correctly evaluated at 64-bit width, but the result is
silently truncated when it is stored back into the 32-bit
fmt_buffer_size variable. For a sufficiently large track range
(start_unit/stop_unit are caller-controlled) this truncation
yields a buffer size far smaller than the number of tracks actually
requested. kzalloc() then succeeds with an undersized allocation,
while the subsequent channel program build still operates on the
untruncated track count and writes past the end of that buffer.
Compute the buffer size with check_mul_overflow() and keep it in a
size_t, so that a value that no longer fits results in -EINVAL
instead of a silently truncated allocation size.
Fixes: 8fd575200d ("s390/dasd: Add new ioctl BIODASDCHECKFMT")
Cc: stable@vger.kernel.org #4.7
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260727142840.567286-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When all channel paths to a DASD device are lost and subsequently
recovered, the path event handler starts one IO per path via
dasd_sleep_on_immediatly() to execute read configuration data (RCD) with
high priority.
dasd_sleep_on_immediatly() works by terminating the currently running
request before inserting the new request.
If a concurrent caller, such as the attention handler
dasd_eckd_check_attention_work() or the summary unit
check handler summary_unit_check_handling_work(), also calls
dasd_sleep_on_immediatly() while a path verification RCD is in progress,
the RCD gets terminated.
The problem is that a terminated request transitions from CLEARED to
TERMINATED without going through the normal retry path in
__dasd_device_process_ccw_queue.
The RCD therefore returns -EIO, and the affected paths remain
non-operational after recovery. RCD CQRs used for path verification
already carry the DASD_CQR_VERIFY_PATH flag.
Extend _dasd_term_running_cqr() to check this flag: instead of terminating
such a request, return -EAGAIN. In dasd_sleep_on_immediatly(), loop on
-EAGAIN with a short sleep, waiting for the path verification request to
complete before inserting the new request.
This is consistent with the already indefinite wait_event() that
dasd_sleep_on_immediatly() uses for its own request, and all other callers
(attention handler, summary unit check handler, reserve/release/steal-lock)
benefit automatically without requiring changes.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260727142840.567286-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The helper function _ip_cprb_helper() uses internal buffer memory for
building and processing CPRBs. After use this buffer was never
scrubbed which could lead to leaving for example clear key material in
memory which could be exposed via tricky reuse of this same memory.
Extend the _ip_cprb_helper() function with another parameter 'scrub'
used to steer scrubbing of this buffer. So now the caller has the
opportunity to decide if scrubbing is needed or not.
Extend the clear key to secure key token import process in function
cca_clr2cipherkey() to tell the helper function from above to scrub
the cprb buffer when the clear key value is part of the request data.
Add explicit scrubbing on return from function cca_clr2cipherkey() for
the random EXOR buffer and the cprb buffer.
Overall this cleans the internal used buffer in case of clear key
import to prevent sensitive data to get exposed.
Fixes: 4bc123b18c ("s390/zcrypt: Add low level functions for CCA AES cipher keys")
Cc: stable@vger.kernel.org
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The domain value is extracted from a given CCA or EP11 ioctl struct
when a CPRB is about to be sent. Thus this is a user controlled value.
Under some special conditions (custom device node used, administrative
load) this value is used as an array index after bounds checking, but
without speculation barrier.
Add the missing array_index_nospec() call to prevent speculative
execution where this domain value is used.
Fixes: cfd68b3309 ("s390/zcrypt: Filter admin CPRBs on custom devices")
Cc: stable@vger.kernel.org
Reported-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Finn Callies <fcallies@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
There is a wrong upper limit check for the domain value when an EP11
CPRB is processed for sending to a crypto card. This check is only
active on custom device nodes but may lead to access heap memory
behind perms->adm when an administrative CPRB is sent.
Add correct limit (AP_DOMAINS = 256) checking to fix this.
Fixes: cfd68b3309 ("s390/zcrypt: Filter admin CPRBs on custom devices")
Cc: stable@vger.kernel.org
Reviewed-by: Finn Callies <fcallies@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add validation of both the actual key buffer size and token length
fields in all the cca_check_sec*token() functions. Additionally check
in cca_gencipherkey() for possible underflow with returned key size.
The CCA token structures contain user-controlled len fields that
were used in operations without proper validation against both the
actual buffer size and minimum token structure size. An attacker
could set this field larger than the actual buffer size, leading to
reading beyond buffer boundaries. This may result in a kernel crash or
exposure of memory via sending this as part of a request down to the
crypto card. Also an attacker could have used a very small len value
and thus enforce a buffer under-run which may produce similar effects
as a over-read.
So now a key must
- key buf length must be at least sizeof the token struct
- the key len field inside the token must fit into the range of
sizeof key token struct ... key buf length
Fixes: 4bc123b18c ("s390/zcrypt: Add low level functions for CCA AES cipher keys")
Cc: stable@vger.kernel.org
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
cca_ecc2protkey() derives the copy length for the CPRB parameter
block directly from the length field in the key token. Reject the
request early if the token length exceeds the available space in the
parameter block.
Fixes: fa6999e326 ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Cc: stable@vger.kernel.org # 5.10+
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
cca_cipher2protkey() derives the copy length for the CPRB parameter
block directly from the length field in the key token. Reject the
request early if the token length exceeds the available space in the
parameter block.
Fixes: 4bc123b18c ("s390/zcrypt: Add low level functions for CCA AES cipher keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Cc: stable@vger.kernel.org # 5.4+
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On a machine without PCI memory-I/O (MIO) support or when running with
pci=nomio the s390 specific PCI MMIO write syscall checks if the MMIO
cookie is above ZPCI_IOMAP_ADDR_BASE as a sanity check before even
trying to perform the MMIO. If this check fails the return value was
left unchanged and thus 0 from prior operations falsely indicating
success. This could potentially confuse user-space into falsely
believing the MMIO, on a mapping not valid for MMIO was successful.
Fix this by setting the return value to -EFAULT prior to the check
following the same pattern as elsewhere in the same function.
Cc: stable@vger.kernel.org
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Fixes: a67a88b0b8 ("s390/pci: remove races against pte updates")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
iomap_split_ioend can split bios that already come from
iomap_ioend_bioset and thus deadlock when the bioset is exhausted.
Add a separate bio_set to avoid this deadlock.
Christian Brauner <brauner@kernel.org> says:
Mark iomap_ioend_split_bioset static as it is only used in ioend.c,
fixing the sparse warning reported by the kernel test robot.
Fixes: 5fcbd555d4 ("iomap: split bios to zone append limits in the submission handlers")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260629125229.3400726-1-hch@lst.de
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
Forking a task that has a pending uretprobe can oops the kernel with a
NULL pointer dereference in the clone() path:
BUG: kernel NULL pointer dereference, address: 0000000000000018
Oops: 0002 [#1] SMP NOPTI
RIP: 0010:hprobe_expire
CR2: 0000000000000018
Call Trace:
uprobe_copy_process
copy_process
kernel_clone
__x64_sys_clone
do_syscall_64
entry_SYSCALL_64_after_hwframe
This was found on real hosts on Meta fleet.
I've got the impression that this is what is happening:
CPU 1 CPU 2 (traced task)
----- -------------------
hit uprobe, prepare_uretprobe():
hprobe LEASED, refcount >= 1
uprobe_unregister()
put_uprobe(): refcount -> 0
fork() -> dup_utask()
hprobe_expire(hprobe, true)
try_get_uprobe() -> NULL
get_uprobe(NULL) <-- Oops
Only take the extra reference when the uprobe is non-NULL; a NULL means
it is gone and is the correct value to return.
Fixes: dd1a756778 ("uprobes: SRCU-protect uretprobe lifetime (with timeout)")
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260729-uprobe-v1-1-61896b87c867@debian.org
