The steering control and semaphore registers are inside an "always on"
power domain with respect to RC6. However there are some issues if
higher-level platform sleep states are entering/exiting at the same time
these registers are accessed. Grabbing GT forcewake and holding it over
the entire lock/steer/unlock cycle ensures that those sleep states have
been fully exited before we access these registers.
This is expected to become a formally documented/numbered workaround
soon.
Note that this patch alone isn't expected to have an immediately
noticeable impact on MCR (mis)behavior; an upcoming pcode firmware
update will also be necessary to provide the other half of this
workaround.
v2:
- Move the forcewake inside the Xe_LPG-specific IP version check. This
should only be necessary on platforms that have a steering semaphore.
Fixes: 3100240bf8 ("drm/i915/mtl: Add hardware-level lock for steering")
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231019170241.2102037-2-matthew.d.roper@intel.com
(cherry picked from commit 8fa1c7cd1f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
drm/logicvc driver is depend on REGMAP and REGMAP_MMIO, should select this
two kconfig option, otherwise the driver failed to compile on platform
without REGMAP_MMIO selected:
ERROR: modpost: "__devm_regmap_init_mmio_clk" [drivers/gpu/drm/logicvc/logicvc-drm.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:136: Module.symvers] Error 1
make: *** [Makefile:1978: modpost] Error 2
Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn>
Acked-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: efeeaefe9b ("drm: Add support for the LogiCVC display controller")
Link: https://patchwork.freedesktop.org/patch/msgid/20230608024207.581401-1-suijingfeng@loongson.cn
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
When supporting OA for TGL, it was seen that the context valid bit in
the report ID was not defined, however revisiting the spec seems to have
this bit defined. The bit is used to determine if a context is valid on
a context switch and is essential to determine active and idle periods
for a context. Re-enable the context valid bit for gen12 platforms.
BSpec: 52196 (description of report_id)
v2: Include BSpec reference (Ashutosh)
Fixes: 00a7f0d715 ("drm/i915/tgl: Add perf support on TGL")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230802202854.1224547-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 7eeaedf799)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In amdgpu_dma_buf_move_notify reserve fences for the page table updates
in amdgpu_vm_clear_freed and amdgpu_vm_handle_moved. This fixes a BUG_ON
in dma_resv_add_fence when using SDMA for page table updates.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As drm_dp_get_mst_branch_device_by_guid() is called from
drm_dp_get_mst_branch_device_by_guid(), mstb parameter has to be checked,
otherwise NULL dereference may occur in the call to
the memcpy() and cause following:
[12579.365869] BUG: kernel NULL pointer dereference, address: 0000000000000049
[12579.365878] #PF: supervisor read access in kernel mode
[12579.365880] #PF: error_code(0x0000) - not-present page
[12579.365882] PGD 0 P4D 0
[12579.365887] Oops: 0000 [#1] PREEMPT SMP NOPTI
...
[12579.365895] Workqueue: events_long drm_dp_mst_up_req_work
[12579.365899] RIP: 0010:memcmp+0xb/0x29
[12579.365921] Call Trace:
[12579.365927] get_mst_branch_device_by_guid_helper+0x22/0x64
[12579.365930] drm_dp_mst_up_req_work+0x137/0x416
[12579.365933] process_one_work+0x1d0/0x419
[12579.365935] worker_thread+0x11a/0x289
[12579.365938] kthread+0x13e/0x14f
[12579.365941] ? process_one_work+0x419/0x419
[12579.365943] ? kthread_blkcg+0x31/0x31
[12579.365946] ret_from_fork+0x1f/0x30
As get_mst_branch_device_by_guid_helper() is recursive, moving condition
to the first line allow to remove a similar one for step over of NULL elements
inside a loop.
Fixes: 5e93b8208d ("drm/dp/mst: move GUID storage from mgr, port to only mst branch")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Reviewed-by: Radoslaw Biernacki <rad@chromium.org>
Signed-off-by: Manasi Navare <navaremanasi@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922063410.23626-1-lma@semihalf.com
If we can't find a free fence register to handle a fault in the GMADR
range just return VM_FAULT_NOPAGE without populating the PTE so that
userspace will retry the access and trigger another fault. Eventually
we should find a free fence and the fault will get properly handled.
A further improvement idea might be to reserve a fence (or one per CPU?)
for the express purpose of handling faults without having to retry. But
that would require some additional work.
Looks like this may have gotten broken originally by
commit 39965b3766 ("drm/i915: don't trash the gtt when running out of fences")
as that changed the errno to -EDEADLK which wasn't handle by the gtt
fault code either. But later in commit 2feeb52859 ("drm/i915/gt: Fix
-EDEADLK handling regression") I changed it again to -ENOBUFS as -EDEADLK
was now getting used for the ww mutex dance. So this fix only makes
sense after that last commit.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9479
Fixes: 2feeb52859 ("drm/i915/gt: Fix -EDEADLK handling regression")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012132801.16292-1-ville.syrjala@linux.intel.com
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
(cherry picked from commit 7f403caabe)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The MediaTek DRM driver implements GEM PRIME vmap by fetching the
sg_table for the object, iterating through the pages, and then
vmapping them. In essence, unlike the GEM DMA helpers which vmap
when the object is first created or imported, the MediaTek version
does it on request.
Unfortunately, the code never correctly frees the sg_table contents.
This results in a kernel memory leak. On a Hayato device with a text
console on the internal display, this results in the system running
out of memory in a few days from all the console screen cursor updates.
Add sg_free_table() to correctly free the contents of the sg_table. This
was missing despite explicitly required by mtk_gem_prime_get_sg_table().
Also move the "out" shortcut label to after the kfree() call for the
sg_table. Having sg_free_table() together with kfree() makes more sense.
The shortcut is only used when the object already has a kernel address,
in which case the pointer is NULL and kfree() does nothing. Hence this
change causes no functional change.
Fixes: 3df64d7b0a ("drm/mediatek: Implement gem prime vmap/vunmap function")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231004083226.1940055-1-wenst@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fixes for v6.6-rc5
- fix to not reset the PHY everytime we start link training but only
do it if link training fails. Without this, the PLL unlocked
interrupt fires causing "Unexpected DP AUX IRQ 0x01000000 when
not busy" spam in the logs since last 2-3 cycles
- correct the highest bank bit to match downstream device tree for
msm8998
- skip the video mode wait if the timing engine is not enabled. This
was introduced after pre_enable flag for DSI video mode panels
where we would end up waiting for the video mode done interrupt
even before enabling timing engine causing error spam and long
bootup times.
- check the correct return code of irq_of_parse_and_map() in DSI code
- avoid overflow issues in the dpu bandwidth calculation . This was
exposed for high resolution displays and a critical fix to avoid
atomic_check failure
- minor fix to add new lines in DP print messages.
- Fix to fail atomic_check() if the resolution exceeds max mdp clk.
This leads to underflow otherwise if we try to allow that frame.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv-HNxQ=VBtZ8geGzYJum9jtManEdbvhcjo_WWF_J9Ziw@mail.gmail.com
In commit 5f04e7ce39 ("drm/panel-edp: Split eDP panels out of
panel-simple") I moved a pile of panels out of panel-simple driver
into the newly created panel-edp driver. One of those panels, however,
shouldn't have been moved.
As is clear from commit e35e305eff ("drm/panel: simple: Add AUO
B116XW03 panel support"), AUX B116XW03 is an LVDS panel. It's used in
exynos5250-snow and exynos5420-peach-pit where it's clear that the
panel is hooked up with LVDS. Furthermore, searching for datasheets I
found one that makes it clear that this panel is LVDS.
As far as I can tell, I got confused because in commit 88d3457ceb
("drm/panel: auo,b116xw03: fix flash backlight when power on") Jitao
Shi added "DRM_MODE_CONNECTOR_eDP". That seems wrong. Looking at the
downstream ChromeOS trees, it seems like some Mediatek boards are
using a panel that they call "auo,b116xw03" that's an eDP panel. The
best I can guess is that they actually have a different panel that has
similar timing. If so then the proper panel should be used or they
should switch to the generic "edp-panel" compatible.
When moving this back to panel-edp, I wasn't sure what to use for
.bus_flags and .bus_format and whether to add the extra "enable" delay
from commit 88d3457ceb ("drm/panel: auo,b116xw03: fix flash
backlight when power on"). I've added formats/flags/delays based on my
(inexpert) analysis of the datasheet. These are untested.
NOTE: if/when this is backported to stable, we might run into some
trouble. Specifically, before 474c162878 ("arm64: dts: mt8183:
jacuzzi: Move panel under aux-bus") this panel was used by
"mt8183-kukui-jacuzzi", which assumed it was an eDP panel. I don't
know what to suggest for that other than someone making up a bogus
panel for jacuzzi that's just for the stable channel.
Fixes: 88d3457ceb ("drm/panel: auo,b116xw03: fix flash backlight when power on")
Fixes: 5f04e7ce39 ("drm/panel-edp: Split eDP panels out of panel-simple")
Tested-by: Anton Bambura <jenneron@postmarketos.org>
Acked-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230925150010.1.Iff672233861bcc4cf25a7ad0a81308adc3bda8a4@changeid
The kernel produces a warning splat and the DSI device fails to register
in this driver if the i2c driver probes, populates child auxiliary
devices, and then somewhere in ti_sn_bridge_probe() a function call
returns -EPROBE_DEFER. When the auxiliary driver probe defers, the dsi
device created by devm_mipi_dsi_device_register_full() is left
registered because the devm managed device used to manage the lifetime
of the DSI device is the parent i2c device, not the auxiliary device
that is being probed.
Associate the DSI device created and managed by this driver to the
lifetime of the auxiliary device, not the i2c device, so that the DSI
device is removed when the auxiliary driver unbinds. Similarly change
the device pointer used for dev_err_probe() so the deferred probe errors
are associated with the auxiliary device instead of the parent i2c
device so we can narrow down future problems faster.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Fixes: c3b75d4734 ("drm/bridge: sn65dsi86: Register and attach our DSI device at probe")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231002235407.769399-1-swboyd@chromium.org
SI hardware does not have doorbells at all, however currently the code
will try to do the allocation and thus fail, makes SI AMDGPU not usable.
Fix this failure by skipping doorbells allocation when doorbells count
is zero.
Fixes: 54c30d2a8d ("drm/amdgpu: create kernel doorbell pages")
Reviewed-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, dpu_plane_atomic_check() does not check whether the
plane can process the image without exceeding the per chipset
limits for MDP clock. This leads to underflow issues because the
SSPP is not able to complete the processing for the data rate of
the display.
Fail the dpu_plane_atomic_check() if the SSPP cannot process the
image without exceeding the MDP clock limits.
changes in v2:
- use crtc_state's adjusted_mode instead of mode
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/556819/
Link: https://lore.kernel.org/r/20230911221627.9569-1-quic_abhinavk@quicinc.com
When a fence signals there is a very small race window where the timestamp
isn't updated yet. sync_file solves this by busy waiting for the
timestamp to appear, but on other ocassions didn't handled this
correctly.
Provide a dma_fence_timestamp() helper function for this and use it in
all appropriate cases.
Another alternative would be to grab the spinlock when that happens.
v2 by teddy: add a wait parameter to wait for the timestamp to show up, in case
the accurate timestamp is needed and/or the timestamp is not based on
ktime (e.g. hw timestamp)
v3 chk: drop the parameter again for unified handling
Signed-off-by: Yunxiang Li <Yunxiang.Li@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 1774baa64f ("drm/scheduler: Change scheduled fence track v2")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20230929104725.2358-1-christian.koenig@amd.com
On some systems with Navi3x dGPU will attempt to use BACO for runtime
PM but fails to resume properly. This is because on these systems
the root port goes into D3cold which is incompatible with BACO.
This happens because in this case dGPU is connected to a bridge between
root port which causes BOCO detection logic to fail. Fix the intent of
the logic by looking at root port, not the immediate upstream bridge for
_PR3.
Cc: stable@vger.kernel.org
Suggested-by: Jun Ma <Jun.Ma2@amd.com>
Tested-by: David Perry <David.Perry@amd.com>
Fixes: b10c1c5b3a ("drm/amdgpu: add check for ACPI power resources")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While aligning SMU11 with SMU13 implementation an assumption was made that
`dpm_context->dpm_tables.pcie_table` was populated in dpm table initialization
like in SMU13 but it isn't.
So restore some of the original logic and instead just check for
amdgpu_device_pcie_dynamic_switching_supported() to decide whether to hardcode
values; erring on the side of performance.
Cc: stable@vger.kernel.org # 6.1+
Reported-and-tested-by: Umio Yasuno <coelacanth_dream@protonmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1447#note_2101382
Fixes: e701156ccc ("drm/amd: Align SMU11 SMU_MSG_OverridePcieParameters implementation with SMU13")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 1ec23ed712 ("drm/i915: Use uabi engines for the default engine
map") switched from using for_each_engine() to for_each_uabi_engine() to
iterate over the user engines. While this seems to be a sensible change,
it's only safe to do when the engines are actually chained using the
rb-tree structure which is not the case during early driver
initialization where it can be either a lock-less list or regular
double-linked list.
In fact, the modesetting initialization code may end up calling
default_engines() through the fb helper code while the engines list
is still llist_node-based:
i915_driver_probe() ->
intel_display_driver_probe() ->
intel_fbdev_init() ->
drm_fb_helper_init() ->
drm_client_init() ->
drm_client_open() ->
drm_file_alloc() ->
i915_driver_open() ->
i915_gem_open() ->
i915_gem_context_open() ->
i915_gem_create_context() ->
default_engines()
Using for_each_uabi_engine() in default_engines() is therefore wrong, as
it would try to interpret the llist as rb-tree, making it find no engine
at all, as the rb_left and rb_right members will still be NULL, as they
haven't been initialized yet.
To fix this type confusion register the engines earlier and at the same
time reduce the amount of code that has to deal with the intermediate
llist state.
Reported-by: sanity checks in grsecurity
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 1ec23ed712 ("drm/i915: Use uabi engines for the default engine map")
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230928182019.10256-2-minipli@grsecurity.net
[tursulin: fixed commit tag typo]
(cherry picked from commit 2b562f032f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
