Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issue: RS-9116 Card is not responding after firmware got loaded.
Root cause: After firmware got loaded, we need to reset the program
counter and few device specific registers. Those registers were not
resetted properly.
Fix: Properly resetting those registers.
Signed-off-by: Ganapathi Kondraju <ganapathirajukondraju@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Surrounding code uses -ERRNO as a result, so don't pass plain -1.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're just trusting that these tables are of the right dimensions, when
we could do better by just using the struct directly. Let's expose the
struct txpwr_lmt_cfg_pair instead.
The table changes were made by using some Vim macros, so that should
help prevent any translation mistakes along the way.
Remaining work: get the 'void *data' out of the generic struct
rtw_table; all of these tables really deserve to be their own data
structure, with proper type fields.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch is to use eth_broadcast_addr() to assign broadcast address
insetad of memcpy().
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Module parameters of 'sw_crypto' and 'disable_watchdog' are false by
default. If new value is desired, we can do it during inserting module,
assignment existing in source code is not reasonable.
Reported-by: David Binderman <dcb314@hotmail.com>
CC: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware crash is a pretty rare event and can't happen too frequently as
it has to be followed by a hardware reinitialization and config reload.
It should be safe to don't use net_ratelimit() when it happens.
For reporting & debugging purposes it's important to provide a complete
log as the last lines are actually the most important. This change
modifies brcmfmac to print all messages in an unlimited way in that
specific case. With this change there should be finally a backtrace of
firmware finally visible after a crash.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It seems we should use 'range' instead of 'priv->range'
in lbtf_geo_init(), because 'range' is the corret one
related to current regioncode.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 691cdb4938 ("libertas_tf: command helper functions for libertas_tf")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a read entry in debugfs to dump current tx power
indexes in use for each path and each rate section.
The corresponding power bases, power by rate, and
power limit are also included.
Also this patch fixes unused function warning.
Fixes: b741422218 ("rtw88: refine flow to get tx power index")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
fix below issue reported by coccicheck
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:514:1-3:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When brcmf_detach() from the bus layer upon rmmod we can no longer
communicate. Hence we will set the bus state to DOWN and cleanup
the event and protocol layer. The network interfaces need to be
deleted before brcmf_cfg80211_detach() because the latter does the
wiphy_unregister() which issues a warning if there are still network
devices linked to the wiphy instance.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver has custom regulatory rules which had maximum bandwidth
for 5GHz channels set to 80MHz. As a consequence the driver can
not use 160MHz in AP mode even when the device supports it. So
relax the rules allowing 160MHz. After wiphy_register() the channel
flags are updated according what the device actually supports.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since each skb in RX ring is reused instead of new allocation, we can
treat the DMA in a more efficient way by DMA synchronization.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Testing with RTL8822BE hardware, when available memory is low, we
frequently see a kernel panic and system freeze.
First, rtw_pci_rx_isr encounters a memory allocation failure (trimmed):
rx routine starvation
WARNING: CPU: 7 PID: 9871 at drivers/net/wireless/realtek/rtw88/pci.c:822 rtw_pci_rx_isr.constprop.25+0x35a/0x370 [rtwpci]
[ 2356.580313] RIP: 0010:rtw_pci_rx_isr.constprop.25+0x35a/0x370 [rtwpci]
Then we see a variety of different error conditions and kernel panics,
such as this one (trimmed):
rtw_pci 0000:02:00.0: pci bus timeout, check dma status
skbuff: skb_over_panic: text:00000000091b6e66 len:415 put:415 head:00000000d2880c6f data:000000007a02b1ea tail:0x1df end:0xc0 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:105!
invalid opcode: 0000 [#1] SMP NOPTI
RIP: 0010:skb_panic+0x43/0x45
When skb allocation fails and the "rx routine starvation" is hit, the
function returns immediately without updating the RX ring. At this
point, the RX ring may continue referencing an old skb which was already
handed off to ieee80211_rx_irqsafe(). When it comes to be used again,
bad things happen.
This patch allocates a new, data-sized skb first in RX ISR. After
copying the data in, we pass it to the upper layers. However, if skb
allocation fails, we effectively drop the frame. In both cases, the
original, full size ring skb is reused.
In addition, to fixing the kernel crash, the RX routine should now
generally behave better under low memory conditions.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=204053
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable rc is being initialized with a value that is never
read and it is being updated later with a new value that is returned.
The variable is redundant and can be replaced with a return 0 as
there are no other return points in this function.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable ret is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi tx power of RTL8723BU is extremely low after booting. So
the WiFi scan gives very limited AP list and it always fails to
connect to the selected AP. This module only supports 1x1 antenna
and the antenna is switched to bluetooth due to some incorrect
register settings.
Compare with the vendor driver https://github.com/lwfinger/rtl8723bu,
we realized that the 8723bu's enable_rf() does the same thing as
rtw_btcoex_HAL_Initialize() in vendor driver. And it by default
sets the antenna path to BTC_ANT_PATH_BT which we verified it's
the cause of the wifi weak tx power. The vendor driver will set
the antenna path to BTC_ANT_PATH_PTA in the consequent btcoexist
mechanism, by the function halbtc8723b1ant_PsTdma.
This commit hand over the antenna control to PTA(Packet Traffic
Arbitration), which compares the weight of bluetooth/wifi traffic
then determine whether to continue current wifi traffic or not.
After PTA take control, The wifi signal will be back to normal and
the bluetooth scan can also work at the same time. However, the
btcoexist still needs to be handled under different circumstances.
If there's a BT connection established, the wifi still fails to
connect until BT disconnected.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In contrast to the TX path, there is no need to separately read the transfer
status from the device after receiving RX data. Consequently, there is no
real STATUS_PENDING RX processing queue entry state.
Remove the unnecessary ENTRY_DATA_STATUS_PENDING flag checks from the RX path.
Also remove the misleading comment about reading RX status from device.
Suggested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Explicitly return constants instead of variable (and rely on
it to be explicitly initialized), if the value is supposed
to be fixed anyways. Align it with the rest of the driver,
which does it the same way.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
John Hurley says:
====================
nfp: Offload MPLS actions
The module act_mpls has recently been added to the kernel. This allows the
manipulation of MPLS headers on packets including push, pop and modify.
Add these new actions and parameters to the intermediate representation
API for hardware offload. Follow this by implementing the offload of these
MPLS actions in the NFP driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS set actions to
firmware. Set actions update the outermost MPLS header. The offload
includes a mask to specify which fields should be set.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS pop actions to
firmware. The act_mpls TC module enforces that the next protocol is
supplied along with the pop action. Passing this to firmware allows it
to properly rebuild the underlying packet after the pop.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS push actions to
firmware.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent addition to TC actions is the ability to manipulate the MPLS
headers on packets.
In preparation to offload such actions to hardware, update the IR code to
accept and prepare the new actions.
Note that no driver currently impliments the MPLS dec_ttl action so this
is not included.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure is too large to put on the stack, resulting in a
warning on 32-bit ARM:
drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c:59:5: error: stack frame size of 1344 bytes in function
'mlx5e_open_xsk' [-Werror,-Wframe-larger-than=]
Use kvzalloc() instead.
Fixes: a038e9794541 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
