Set off-on-delay-us to 500000 us for pp3300_mipibrdg to make sure it
complies with the panel's unprepare delay (the time to power down
completely) of the power sequence. Explicit configuration on the
regulator node is required because mt8192-asurada uses the same power
supply for the panel and the anx7625 DP bridge.
For example, the power sequence could be violated in this sequence:
1. Bridge on: panel goes off, but regulator doesn't turn off (refcount=1).
2. Bridge off: regulator turns off (refcount=0).
3. Bridge resume -> regulator turns on but the bridge driver doesn't
check the delay.
Or in this sequence:
1. Bridge on: panel goes off. The regulator doesn't turn off (refcount=1),
but the .unprepared_time in panel_edp is still updated.
2. Bridge off, regulator goes off (refcount=0).
3. Panel on, but the panel driver uses the wrong .unprepared_time to check
the unprepare delay.
Fixes: f9f00b1f6b ("arm64: dts: mediatek: asurada: Add display regulators")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240502154455.3427793-1-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This patch fixes an issue where xhci1 was not functioning properly because
the state and PHY settings were incorrect.
The introduction of the 'force-mode' property in the phy-mtk-tphy driver
allows for the correct initialization of xhci1 by updating the Device Tree
settings accordingly.
The necessary fixup which added support for the 'force-mode' switch in the
phy-mtk-tphy driver.
commit 9b27303003 ("phy: mediatek: tphy: add support force phy mode switch")
Link: https://lore.kernel.org/r/20231211025624.28991-2-chunfeng.yun@mediatek.com
Prior to this fix, the system would exhibit the following probe failure messages
for xhci1:
xhci-mtk 11290000.usb: supply vbus not found, using dummy regulator
xhci-mtk 11290000.usb: uwk - reg:0x400, version:104
xhci-mtk 11290000.usb: xHCI Host Controller
xhci-mtk 11290000.usb: new USB bus registered, assigned bus number 5
xhci-mtk 11290000.usb: clocks are not stable (0x1003d0f)
xhci-mtk 11290000.usb: can't setup: -110
xhci-mtk 11290000.usb: USB bus 5 deregistered
xhci-mtk: probe of 11290000.usb failed with error -110
With the application of this dts fixup, the aforementioned initialization errors
are resolved and xhci1 is working.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20240216095751.4937-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a devicetree for the Cherry Dojo (HP Chromebook x360 13b-ca0002sa)
convertible type machine.
Differences with the already supported Tomato machines include:
- Different speaker amplifiers (Dual MAX98380, one per channel)
- I2C Touchscreen is on a different address (though still a HID device)
- Has NVMe storage on the PCIe0 controller
- Slightly different keyboard top row keymap
Link: https://lore.kernel.org/r/20240314103500.93158-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The "output-enable" property is set on uart1's RTS pin. This is bogus
because the hardware does not actually have a controllable output
buffer. Secondly, the implementation incorrectly treats this property
as a request to switch the pin to GPIO output. This does not fit the
intended semantic of "output-enable" and it does not have any affect
either because the pin is muxed to the UART function, not the GPIO
function.
Drop the property.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240412075613.1200048-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The thermal zones in MT8183 had cryptic names and all of them, apart
from the cpu-thermal zone, had no thermal trips, hence those were not
probed at all.
Refactor the tzts1..5 and tztsABB thermal zones to add the correct
thermal trips and give them a meaningful name, corresponding to the
actually monitored thermal zone.
While at it, also rename the thermal sensor node to "thermal-sensor".
Now the thermal zones are probing and their temperatures can be read.
Fixes: b325ce3978 ("arm64: dts: mt8183: add thermal zone node")
Link: https://lore.kernel.org/r/20240410083002.1357857-4-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add basic device-tree for the Genio 700 EVK board. The
Genio 700 EVK is based on MediaTek MT8390 SoC.
MT8390 hardware register maps are identical to MT8188.
The Genio 700 EVK has following features:
- MT8390 SoC
- MT6365 PMIC
- MT6319 Buck IC
- 12V DC Jack
- 2x4GB LPDDR4X
- 64GB eMMC 5.1
- 64Mb SPI NOR
- M.2 Key A-E slot with PCIe Gen2 and USB 2.0
- 2x DSI LCM ports
- 2x touch sensor ports
- 2x MIPI-CSI, as camera daughter board slots
- USB 2 micro USB connector
- USB 3 with 1 to 2 hub:
- M.2 Key B slot
- Type-C connector, with DisplayPort over Type-C
- HDMI 2.0 TX port with Type A HDMI connector
- eDP port
- Gigabit Ethernet with RJ45 connector
- SD card slot
- Earphone Jack
- Analog Microphone
- 2x Digital Microphone
- 3x UART with serial-to-usb converters and micro USB connectors
Signed-off-by: Chris-QJ Chen <chris-qj.chen@mediatek.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915081212.13959-2-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc22a ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
Pull irq fixes from Ingo Molnar:
- Fix x86 IRQ vector leak caused by a CPU offlining race
- Fix build failure in the riscv-imsic irqchip driver
caused by an API-change semantic conflict
- Fix use-after-free in irq_find_at_or_after()
* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
Pull x86 fixes from Ingo Molnar:
- Fix regressions of the new x86 CPU VFM (vendor/family/model)
enumeration/matching code
- Fix crash kernel detection on buggy firmware with
non-compliant ACPI MADT tables
- Address Kconfig warning
* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
crypto: x86/aes-xts - switch to new Intel CPU model defines
x86/topology: Handle bogus ACPI tables correctly
x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y
Pull ipmi updates from Corey Minyard:
"Mostly updates for deprecated interfaces, platform.remove and
converting from a tasklet to a BH workqueue.
Also use HAS_IOPORT for disabling inb()/outb()"
* tag 'for-linus-6.10-1' of https://github.com/cminyard/linux-ipmi:
ipmi: kcs_bmc_npcm7xx: Convert to platform remove callback returning void
ipmi: kcs_bmc_aspeed: Convert to platform remove callback returning void
ipmi: ipmi_ssif: Convert to platform remove callback returning void
ipmi: ipmi_si_platform: Convert to platform remove callback returning void
ipmi: ipmi_powernv: Convert to platform remove callback returning void
ipmi: bt-bmc: Convert to platform remove callback returning void
char: ipmi: handle HAS_IOPORT dependencies
ipmi: Convert from tasklet to BH workqueue
Pull ceph updates from Ilya Dryomov:
"A series from Xiubo that adds support for additional access checks
based on MDS auth caps which were recently made available to clients.
This is needed to prevent scenarios where the MDS quietly discards
updates that a UID-restricted client previously (wrongfully) acked to
the user.
Other than that, just a documentation fixup"
* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
doc: ceph: update userspace command to get CephFS metadata
ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
ceph: check the cephx mds auth access for async dirop
ceph: check the cephx mds auth access for open
ceph: check the cephx mds auth access for setattr
ceph: add ceph_mds_check_access() helper
ceph: save cap_auths in MDS client when session is opened
Pull ntfs3 updates from Konstantin Komarov:
"Fixes:
- reusing of the file index (could cause the file to be trimmed)
- infinite dir enumeration
- taking DOS names into account during link counting
- le32_to_cpu conversion, 32 bit overflow, NULL check
- some code was refactored
Changes:
- removed max link count info display during driver init
Remove:
- atomic_open has been removed for lack of use"
* tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: Break dir enumeration if directory contents error
fs/ntfs3: Fix case when index is reused during tree transformation
fs/ntfs3: Mark volume as dirty if xattr is broken
fs/ntfs3: Always make file nonresident on fallocate call
fs/ntfs3: Redesign ntfs_create_inode to return error code instead of inode
fs/ntfs3: Use variable length array instead of fixed size
fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
fs/ntfs3: Check 'folio' pointer for NULL
fs/ntfs3: Missed le32_to_cpu conversion
fs/ntfs3: Remove max link count info display during driver init
fs/ntfs3: Taking DOS names into account during link counting
fs/ntfs3: remove atomic_open
fs/ntfs3: use kcalloc() instead of kzalloc()
Pull smb server fixes from Steve French:
"Two ksmbd server fixes, both for stable"
* tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: ignore trailing slashes in share paths
ksmbd: avoid to send duplicate oplock break notifications
Pull RTC updates from Alexandre Belloni:
"There is one new driver and then most of the changes are the device
tree bindings conversions to yaml.
New driver:
- Epson RX8111
Drivers:
- Many Device Tree bindings conversions to dtschema
- pcf8563: wakeup-source support"
* tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
pcf8563: add wakeup-source support
rtc: rx8111: handle VLOW flag
rtc: rx8111: demote warnings to debug level
rtc: rx6110: Constify struct regmap_config
dt-bindings: rtc: convert trivial devices into dtschema
dt-bindings: rtc: stmp3xxx-rtc: convert to dtschema
dt-bindings: rtc: pxa-rtc: convert to dtschema
rtc: Add driver for Epson RX8111
dt-bindings: rtc: Add Epson RX8111
rtc: mcp795: drop unneeded MODULE_ALIAS
rtc: nuvoton: Modify part number value
rtc: test: Split rtc unit test into slow and normal speed test
dt-bindings: rtc: nxp,lpc1788-rtc: convert to dtschema
dt-bindings: rtc: digicolor-rtc: move to trivial-rtc
dt-bindings: rtc: alphascale,asm9260-rtc: convert to dtschema
dt-bindings: rtc: armada-380-rtc: convert to dtschema
rtc: cros-ec: provide ID table for avoiding fallback match
